提交 bd529cfb 编写于 作者: E Evgeniy Polyakov 提交者: Greg Kroah-Hartman

[PATCH] W1: Move w1 bus master code into 'w1/masters' and move w1 slave code into 'w1/slaves'

Signed-off-by: NBen Gardner <bgardner@wabtec.com>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
上级 ccd69940
...@@ -11,63 +11,7 @@ config W1 ...@@ -11,63 +11,7 @@ config W1
This W1 support can also be built as a module. If so, the module This W1 support can also be built as a module. If so, the module
will be called wire.ko. will be called wire.ko.
config W1_MATROX source drivers/w1/masters/Kconfig
tristate "Matrox G400 transport layer for 1-wire" source drivers/w1/slaves/Kconfig
depends on W1 && PCI
help
Say Y here if you want to communicate with your 1-wire devices
using Matrox's G400 GPIO pins.
This support is also available as a module. If so, the module
will be called matrox_w1.ko.
config W1_DS9490
tristate "DS9490R transport layer driver"
depends on W1 && USB
help
Say Y here if you want to have a driver for DS9490R UWB <-> W1 bridge.
This support is also available as a module. If so, the module
will be called ds9490r.ko.
config W1_DS9490_BRIDGE
tristate "DS9490R USB <-> W1 transport layer for 1-wire"
depends on W1_DS9490
help
Say Y here if you want to communicate with your 1-wire devices
using DS9490R USB bridge.
This support is also available as a module. If so, the module
will be called ds_w1_bridge.ko.
config W1_THERM
tristate "Thermal family implementation"
depends on W1
help
Say Y here if you want to connect 1-wire thermal sensors to you
wire.
config W1_SMEM
tristate "Simple 64bit memory family implementation"
depends on W1
help
Say Y here if you want to connect 1-wire
simple 64bit memory rom(ds2401/ds2411/ds1990*) to you wire.
config W1_DS2433
tristate "4kb EEPROM family support (DS2433)"
depends on W1
help
Say Y here if you want to use a 1-wire
4kb EEPROM family device (DS2433).
config W1_DS2433_CRC
bool "Protect DS2433 data with a CRC16"
depends on W1_DS2433
select CRC16
help
Say Y here to protect DS2433 data with a CRC16.
Each block has 30 bytes of data and a two byte CRC16.
Full block writes are only allowed if the CRC is valid.
endmenu endmenu
...@@ -13,13 +13,5 @@ endif ...@@ -13,13 +13,5 @@ endif
obj-$(CONFIG_W1) += wire.o obj-$(CONFIG_W1) += wire.o
wire-objs := w1.o w1_int.o w1_family.o w1_netlink.o w1_io.o wire-objs := w1.o w1_int.o w1_family.o w1_netlink.o w1_io.o
obj-$(CONFIG_W1_MATROX) += matrox_w1.o obj-y += masters/ slaves/
obj-$(CONFIG_W1_THERM) += w1_therm.o
obj-$(CONFIG_W1_SMEM) += w1_smem.o
obj-$(CONFIG_W1_DS9490) += ds9490r.o
ds9490r-objs := dscore.o
obj-$(CONFIG_W1_DS9490_BRIDGE) += ds_w1_bridge.o
obj-$(CONFIG_W1_DS2433) += w1_ds2433.o
#
# 1-wire bus master configuration
#
menu "1-wire Bus Masters"
depends on W1
config W1_MASTER_MATROX
tristate "Matrox G400 transport layer for 1-wire"
depends on W1 && PCI
help
Say Y here if you want to communicate with your 1-wire devices
using Matrox's G400 GPIO pins.
This support is also available as a module. If so, the module
will be called matrox_w1.ko.
config W1_MASTER_DS9490
tristate "DS9490R transport layer driver"
depends on W1 && USB
help
Say Y here if you want to have a driver for DS9490R UWB <-> W1 bridge.
This support is also available as a module. If so, the module
will be called ds9490r.ko.
config W1_MASTER_DS9490_BRIDGE
tristate "DS9490R USB <-> W1 transport layer for 1-wire"
depends on W1_DS9490
help
Say Y here if you want to communicate with your 1-wire devices
using DS9490R USB bridge.
This support is also available as a module. If so, the module
will be called ds_w1_bridge.ko.
endmenu
#
# Makefile for 1-wire bus master drivers.
#
obj-$(CONFIG_W1_MASTER_MATROX) += matrox_w1.o
obj-$(CONFIG_W1_MASTER_DS9490) += ds9490r.o
ds9490r-objs := dscore.o
obj-$(CONFIG_W1_MASTER_DS9490_BRIDGE) += ds_w1_bridge.o
...@@ -22,8 +22,8 @@ ...@@ -22,8 +22,8 @@
#include <linux/module.h> #include <linux/module.h>
#include <linux/types.h> #include <linux/types.h>
#include "../w1/w1.h" #include "../w1.h"
#include "../w1/w1_int.h" #include "../w1_int.h"
#include "dscore.h" #include "dscore.h"
static struct ds_device *ds_dev; static struct ds_device *ds_dev;
......
...@@ -340,7 +340,7 @@ int ds_reset(struct ds_device *dev, struct ds_status *st) ...@@ -340,7 +340,7 @@ int ds_reset(struct ds_device *dev, struct ds_status *st)
return -EIO; return -EIO;
} }
#endif #endif
return 0; return 0;
} }
...@@ -348,7 +348,7 @@ int ds_reset(struct ds_device *dev, struct ds_status *st) ...@@ -348,7 +348,7 @@ int ds_reset(struct ds_device *dev, struct ds_status *st)
int ds_set_speed(struct ds_device *dev, int speed) int ds_set_speed(struct ds_device *dev, int speed)
{ {
int err; int err;
if (speed != SPEED_NORMAL && speed != SPEED_FLEXIBLE && speed != SPEED_OVERDRIVE) if (speed != SPEED_NORMAL && speed != SPEED_FLEXIBLE && speed != SPEED_OVERDRIVE)
return -EINVAL; return -EINVAL;
......
...@@ -19,8 +19,8 @@ ...@@ -19,8 +19,8 @@
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/ */
#include <asm/atomic.h>
#include <asm/types.h> #include <asm/types.h>
#include <asm/atomic.h>
#include <asm/io.h> #include <asm/io.h>
#include <linux/delay.h> #include <linux/delay.h>
...@@ -35,9 +35,9 @@ ...@@ -35,9 +35,9 @@
#include <linux/pci.h> #include <linux/pci.h>
#include <linux/timer.h> #include <linux/timer.h>
#include "w1.h" #include "../w1.h"
#include "w1_int.h" #include "../w1_int.h"
#include "w1_log.h" #include "../w1_log.h"
MODULE_LICENSE("GPL"); MODULE_LICENSE("GPL");
MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>"); MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>");
......
#
# 1-wire slaves configuration
#
menu "1-wire Slaves"
depends on W1
config W1_SLAVE_THERM
tristate "Thermal family implementation"
depends on W1
help
Say Y here if you want to connect 1-wire thermal sensors to you
wire.
config W1_SLAVE_SMEM
tristate "Simple 64bit memory family implementation"
depends on W1
help
Say Y here if you want to connect 1-wire
simple 64bit memory rom(ds2401/ds2411/ds1990*) to you wire.
config W1_SLAVE_DS2433
tristate "4kb EEPROM family support (DS2433)"
depends on W1
help
Say Y here if you want to use a 1-wire
4kb EEPROM family device (DS2433).
config W1_SLAVE_DS2433_CRC
bool "Protect DS2433 data with a CRC16"
depends on W1_DS2433
select CRC16
help
Say Y here to protect DS2433 data with a CRC16.
Each block has 30 bytes of data and a two byte CRC16.
Full block writes are only allowed if the CRC is valid.
endmenu
#
# Makefile for the Dallas's 1-wire slaves.
#
ifeq ($(CONFIG_W1_SLAVE_DS2433_CRC), y)
EXTRA_CFLAGS += -DCONFIG_W1_F23_CRC
endif
obj-$(CONFIG_W1_SLAVE_THERM) += w1_therm.o
obj-$(CONFIG_W1_SLAVE_SMEM) += w1_smem.o
obj-$(CONFIG_W1_SLAVE_DS2433) += w1_ds2433.o
...@@ -21,10 +21,10 @@ ...@@ -21,10 +21,10 @@
#endif #endif
#include "w1.h" #include "../w1.h"
#include "w1_io.h" #include "../w1_io.h"
#include "w1_int.h" #include "../w1_int.h"
#include "w1_family.h" #include "../w1_family.h"
MODULE_LICENSE("GPL"); MODULE_LICENSE("GPL");
MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>"); MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
......
...@@ -27,10 +27,10 @@ ...@@ -27,10 +27,10 @@
#include <linux/device.h> #include <linux/device.h>
#include <linux/types.h> #include <linux/types.h>
#include "w1.h" #include "../w1.h"
#include "w1_io.h" #include "../w1_io.h"
#include "w1_int.h" #include "../w1_int.h"
#include "w1_family.h" #include "../w1_family.h"
MODULE_LICENSE("GPL"); MODULE_LICENSE("GPL");
MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>"); MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>");
...@@ -51,7 +51,7 @@ static int __init w1_smem_init(void) ...@@ -51,7 +51,7 @@ static int __init w1_smem_init(void)
err = w1_register_family(&w1_smem_family_01); err = w1_register_family(&w1_smem_family_01);
if (err) if (err)
return err; return err;
err = w1_register_family(&w1_smem_family_81); err = w1_register_family(&w1_smem_family_81);
if (err) { if (err) {
w1_unregister_family(&w1_smem_family_01); w1_unregister_family(&w1_smem_family_01);
......
...@@ -28,10 +28,10 @@ ...@@ -28,10 +28,10 @@
#include <linux/types.h> #include <linux/types.h>
#include <linux/delay.h> #include <linux/delay.h>
#include "w1.h" #include "../w1.h"
#include "w1_io.h" #include "../w1_io.h"
#include "w1_int.h" #include "../w1_int.h"
#include "w1_family.h" #include "../w1_family.h"
MODULE_LICENSE("GPL"); MODULE_LICENSE("GPL");
MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>"); MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>");
...@@ -123,12 +123,12 @@ static inline int w1_DS18S20_convert_temp(u8 rom[9]) ...@@ -123,12 +123,12 @@ static inline int w1_DS18S20_convert_temp(u8 rom[9])
if (!rom[7]) if (!rom[7])
return 0; return 0;
if (rom[1] == 0) if (rom[1] == 0)
t = ((s32)rom[0] >> 1)*1000; t = ((s32)rom[0] >> 1)*1000;
else else
t = 1000*(-1*(s32)(0x100-rom[0]) >> 1); t = 1000*(-1*(s32)(0x100-rom[0]) >> 1);
t -= 250; t -= 250;
h = 1000*((s32)rom[7] - (s32)rom[6]); h = 1000*((s32)rom[7] - (s32)rom[6]);
h /= (s32)rom[7]; h /= (s32)rom[7];
...@@ -231,7 +231,7 @@ static ssize_t w1_therm_read_bin(struct kobject *kobj, char *buf, loff_t off, si ...@@ -231,7 +231,7 @@ static ssize_t w1_therm_read_bin(struct kobject *kobj, char *buf, loff_t off, si
for (i = 0; i < 9; ++i) for (i = 0; i < 9; ++i)
count += sprintf(buf + count, "%02x ", sl->rom[i]); count += sprintf(buf + count, "%02x ", sl->rom[i]);
count += sprintf(buf + count, "t=%d\n", w1_convert_temp(rom, sl->family->fid)); count += sprintf(buf + count, "t=%d\n", w1_convert_temp(rom, sl->family->fid));
out: out:
up(&dev->mutex); up(&dev->mutex);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册