提交 a490631f 编写于 作者: F Florian Fainelli 提交者: David S. Miller

net: phy: bcm7xxx: add PHY revision D0 workaround sequence

PHY revision D0 requires a specific workaround sequence which needs to
be applied to get the HW to behave properly in all corner cases
conditions. Do this based on the revision we just read out of the HW
using a specific function.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 9c41f2ba
......@@ -39,8 +39,11 @@
#define AFE_RXCONFIG_0 MISC_ADDR(0x38, 0)
#define AFE_RXCONFIG_1 MISC_ADDR(0x38, 1)
#define AFE_RXCONFIG_2 MISC_ADDR(0x38, 2)
#define AFE_RX_LP_COUNTER MISC_ADDR(0x38, 3)
#define AFE_TX_CONFIG MISC_ADDR(0x39, 0)
#define AFE_VDCA_ICTRL_0 MISC_ADDR(0x39, 1)
#define AFE_VDAC_OTHERS_0 MISC_ADDR(0x39, 3)
#define AFE_HPF_TRIM_OTHERS MISC_ADDR(0x3a, 0)
#define CORE_EXPB0 0xb0
......@@ -119,6 +122,46 @@ static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev)
return 0;
}
static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
{
/* AFE_RXCONFIG_0 */
phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);
/* AFE_RXCONFIG_1 */
phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
/* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */
phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);
/* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
/* AFE_TX_CONFIG, set 1000BT Cfeed=110 for all ports */
phy_write_misc(phydev, AFE_TX_CONFIG, 0x0061);
/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
/* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);
/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
* offset for HT=0 code
*/
phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);
/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
phy_write_misc(phydev, DSP_TAP10, 0x011b);
/* Reset R_CAL/RC_CAL engine */
r_rc_cal_reset(phydev);
return 0;
}
static int bcm7xxx_apd_enable(struct phy_device *phydev)
{
int val;
......@@ -179,6 +222,9 @@ static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
case 0xb0:
ret = bcm7xxx_28nm_b0_afe_config_init(phydev);
break;
case 0xd0:
ret = bcm7xxx_28nm_d0_afe_config_init(phydev);
break;
default:
break;
}
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册