提交 9546aae0 编写于 作者: S Sujith 提交者: John W. Linville

ath9k: Cleanup beacon stuck processing

We never use SC_OP_NO_RESET, it is not configurable at all.
Remove all code that deals with this flag and make beacon
stuck processing simple.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 9fc9ab0a
......@@ -549,17 +549,16 @@ struct ath_rfkill {
#define SC_OP_TXAGGR BIT(3)
#define SC_OP_CHAINMASK_UPDATE BIT(4)
#define SC_OP_FULL_RESET BIT(5)
#define SC_OP_NO_RESET BIT(6)
#define SC_OP_PREAMBLE_SHORT BIT(7)
#define SC_OP_PROTECT_ENABLE BIT(8)
#define SC_OP_RXFLUSH BIT(9)
#define SC_OP_LED_ASSOCIATED BIT(10)
#define SC_OP_RFKILL_REGISTERED BIT(11)
#define SC_OP_RFKILL_SW_BLOCKED BIT(12)
#define SC_OP_RFKILL_HW_BLOCKED BIT(13)
#define SC_OP_WAIT_FOR_BEACON BIT(14)
#define SC_OP_LED_ON BIT(15)
#define SC_OP_SCANNING BIT(16)
#define SC_OP_PREAMBLE_SHORT BIT(6)
#define SC_OP_PROTECT_ENABLE BIT(7)
#define SC_OP_RXFLUSH BIT(8)
#define SC_OP_LED_ASSOCIATED BIT(9)
#define SC_OP_RFKILL_REGISTERED BIT(10)
#define SC_OP_RFKILL_SW_BLOCKED BIT(11)
#define SC_OP_RFKILL_HW_BLOCKED BIT(12)
#define SC_OP_WAIT_FOR_BEACON BIT(13)
#define SC_OP_LED_ON BIT(14)
#define SC_OP_SCANNING BIT(15)
struct ath_bus_ops {
void (*read_cachesize)(struct ath_softc *sc, int *csz);
......
......@@ -49,13 +49,6 @@ static int ath_beaconq_config(struct ath_softc *sc)
}
}
static void ath_bstuck_process(struct ath_softc *sc)
{
DPRINTF(sc, ATH_DBG_BEACON, "stuck beacon; resetting (bmiss count %u)\n",
sc->beacon.bmisscnt);
ath_reset(sc, false);
}
/*
* Associates the beacon frame buffer with a transmit descriptor. Will set
* up all required antenna switch parameters, rate codes, and channel flags.
......@@ -401,83 +394,37 @@ void ath_beacon_tasklet(unsigned long data)
struct ath_hw *ah = sc->sc_ah;
struct ath_buf *bf = NULL;
int slot, if_id;
u32 bfaddr, show_cycles = 0, bc = 0, tsftu;
u32 rx_clear = 0, rx_frame = 0, tx_frame = 0;
u32 bfaddr, bc = 0, tsftu;
u64 tsf;
u16 intval;
if (sc->sc_flags & SC_OP_NO_RESET) {
show_cycles = ath9k_hw_GetMibCycleCountsPct(ah,
&rx_clear, &rx_frame, &tx_frame);
}
/*
* Check if the previous beacon has gone out. If
* not don't try to post another, skip this period
* and wait for the next. Missed beacons indicate
* a problem and should not occur. If we miss too
* many consecutive beacons reset the device.
*
* FIXME: Clean up this mess !!
*/
if (ath9k_hw_numtxpending(ah, sc->beacon.beaconq) != 0) {
sc->beacon.bmisscnt++;
/* XXX: doth needs the chanchange IE countdown decremented.
* We should consider adding a mac80211 call to indicate
* a beacon miss so appropriate action could be taken
* (in that layer).
*/
if (sc->beacon.bmisscnt < BSTUCK_THRESH) {
if (sc->sc_flags & SC_OP_NO_RESET) {
DPRINTF(sc, ATH_DBG_BEACON,
"missed %u consecutive beacons\n",
sc->beacon.bmisscnt);
if (show_cycles) {
/*
* Display cycle counter stats from HW
* to aide in debug of stickiness.
*/
DPRINTF(sc, ATH_DBG_BEACON,
"busy times: rx_clear=%d, "
"rx_frame=%d, tx_frame=%d\n",
rx_clear, rx_frame,
tx_frame);
} else {
DPRINTF(sc, ATH_DBG_BEACON,
"unable to obtain "
"busy times\n");
}
} else {
DPRINTF(sc, ATH_DBG_BEACON,
"missed %u consecutive beacons\n",
sc->beacon.bmisscnt);
}
DPRINTF(sc, ATH_DBG_BEACON,
"missed %u consecutive beacons\n",
sc->beacon.bmisscnt);
} else if (sc->beacon.bmisscnt >= BSTUCK_THRESH) {
if (sc->sc_flags & SC_OP_NO_RESET) {
if (sc->beacon.bmisscnt == BSTUCK_THRESH) {
DPRINTF(sc, ATH_DBG_BEACON,
"beacon is officially "
"stuck\n");
}
} else {
DPRINTF(sc, ATH_DBG_BEACON,
"beacon is officially stuck\n");
ath_bstuck_process(sc);
}
DPRINTF(sc, ATH_DBG_BEACON,
"beacon is officially stuck\n");
ath_reset(sc, false);
}
return;
}
if (sc->beacon.bmisscnt != 0) {
if (sc->sc_flags & SC_OP_NO_RESET) {
DPRINTF(sc, ATH_DBG_BEACON,
"resume beacon xmit after %u misses\n",
sc->beacon.bmisscnt);
} else {
DPRINTF(sc, ATH_DBG_BEACON,
"resume beacon xmit after %u misses\n",
sc->beacon.bmisscnt);
}
DPRINTF(sc, ATH_DBG_BEACON,
"resume beacon xmit after %u misses\n",
sc->beacon.bmisscnt);
sc->beacon.bmisscnt = 0;
}
......@@ -497,8 +444,7 @@ void ath_beacon_tasklet(unsigned long data)
DPRINTF(sc, ATH_DBG_BEACON,
"slot %d [tsf %llu tsftu %u intval %u] if_id %d\n",
slot, (unsigned long long)tsf, tsftu,
intval, if_id);
slot, tsf, tsftu, intval, if_id);
bfaddr = 0;
if (if_id != ATH_IF_ID_ANY) {
......@@ -508,6 +454,7 @@ void ath_beacon_tasklet(unsigned long data)
bc = 1;
}
}
/*
* Handle slot time change when a non-ERP station joins/leaves
* an 11g network. The 802.11 layer notifies us via callback,
......@@ -524,7 +471,6 @@ void ath_beacon_tasklet(unsigned long data)
* interval has passed. When bursting slot is always left
* set to ATH_BCBUF so this check is a noop.
*/
/* XXX locking */
if (sc->beacon.updateslot == UPDATE) {
sc->beacon.updateslot = COMMIT; /* commit next beacon */
sc->beacon.slotupdate = slot;
......@@ -541,7 +487,6 @@ void ath_beacon_tasklet(unsigned long data)
if (!ath9k_hw_stoptxdma(ah, sc->beacon.beaconq)) {
DPRINTF(sc, ATH_DBG_FATAL,
"beacon queue %u did not stop?\n", sc->beacon.beaconq);
/* NB: the HAL still stops DMA, so proceed */
}
/* NB: cabq traffic should already be queued and primed */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册