提交 7b01773b 编写于 作者: L Linus Torvalds

Merge branch 'for-linus' of git://github.com/at91linux/linux-2.6-at91

* 'for-linus' of git://github.com/at91linux/linux-2.6-at91:
  at91: at91sam9g20ek modify dual slot evaluation kit
......@@ -289,13 +289,6 @@ config MACH_NEOCORE926
help
Select this if you are using the Adeneo Neocore 926 board.
config MACH_AT91SAM9G20EK_2MMC
bool "Atmel AT91SAM9G20-EK Evaluation Kit modified for 2 MMC Slots"
depends on ARCH_AT91SAM9G20
help
Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
Rev A or B modified for 2 MMC Slots.
endif
# ----------------------------------------------------------
......@@ -322,7 +315,16 @@ config MACH_AT91SAM9G20EK
bool "Atmel AT91SAM9G20-EK Evaluation Kit"
depends on ARCH_AT91SAM9G20
help
Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit.
Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit
that embeds only one SD/MMC slot.
config MACH_AT91SAM9G20EK_2MMC
bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots"
depends on ARCH_AT91SAM9G20
help
Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and
onwards.
config MACH_CPU9G20
bool "Eukrea CPU9G20 board"
......@@ -392,7 +394,7 @@ config MTD_AT91_DATAFLASH_CARD
config MTD_NAND_ATMEL_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)
depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G20EK_2MMC || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)
help
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
......
......@@ -90,7 +90,7 @@ static struct at91_udc_data __initdata ek_udc_data = {
* SPI devices.
*/
static struct spi_board_info ek_spi_devices[] = {
#if !defined(CONFIG_MMC_ATMELMCI)
#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91))
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.chip_select = 1,
......@@ -113,7 +113,7 @@ static struct spi_board_info ek_spi_devices[] = {
* MACB Ethernet device
*/
static struct at91_eth_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PC12,
.phy_irq_pin = AT91_PIN_PB0,
.is_rmii = 1,
};
......@@ -194,24 +194,27 @@ static void __init ek_add_device_nand(void)
/*
* MCI (SD/MMC)
* det_pin and wp_pin are not connected
* wp_pin is not connected
*/
#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
static struct mci_platform_data __initdata ek_mmc_data = {
.slot[0] = {
.bus_width = 4,
.detect_pin = -ENODEV,
.detect_pin = AT91_PIN_PC2,
.wp_pin = -ENODEV,
},
.slot[1] = {
.bus_width = 4,
.detect_pin = -ENODEV,
.detect_pin = AT91_PIN_PC9,
.wp_pin = -ENODEV,
},
};
#else
static struct amci_platform_data __initdata ek_mmc_data = {
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 1, /* Only one slot so use slot B */
.wire4 = 1,
.det_pin = AT91_PIN_PC9,
};
#endif
......@@ -221,13 +224,13 @@ static struct amci_platform_data __initdata ek_mmc_data = {
static struct gpio_led ek_leds[] = {
{ /* "bottom" led, green, userled1 to be defined */
.name = "ds5",
.gpio = AT91_PIN_PB12,
.gpio = AT91_PIN_PB8,
.active_low = 1,
.default_trigger = "none",
},
{ /* "power" led, yellow */
.name = "ds1",
.gpio = AT91_PIN_PB13,
.gpio = AT91_PIN_PB9,
.default_trigger = "heartbeat",
}
};
......@@ -254,7 +257,11 @@ static void __init ek_board_init(void)
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
at91_add_device_mci(0, &ek_mmc_data);
#else
at91_add_device_mmc(0, &ek_mmc_data);
#endif
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* LEDs */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册