提交 25930707 编写于 作者: C Corey Minyard

ipmi: Add SMBus interface driver (SSIF)

This patch adds the SMBus interface to the IPMI driver.
Signed-off-by: NCorey Minyard <minyard@acm.org>

 Documentation/IPMI.txt       |   32
 drivers/char/ipmi/Kconfig    |   11
 drivers/char/ipmi/Makefile   |    1
 drivers/char/ipmi/ipmi_smb.c | 1737 +++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 1769 insertions(+), 12 deletions(-)
上级 99ab32f3
......@@ -42,7 +42,13 @@ The driver interface depends on your hardware. If your system
properly provides the SMBIOS info for IPMI, the driver will detect it
and just work. If you have a board with a standard interface (These
will generally be either "KCS", "SMIC", or "BT", consult your hardware
manual), choose the 'IPMI SI handler' option.
manual), choose the 'IPMI SI handler' option. A driver also exists
for direct I2C access to the IPMI management controller. Some boards
support this, but it is unknown if it will work on every board. For
this, choose 'IPMI SMBus handler', but be ready to try to do some
figuring to see if it will work on your system if the SMBIOS/APCI
information is wrong or not present. It is fairly safe to have both
these enabled and let the drivers auto-detect what is present.
You should generally enable ACPI on your system, as systems with IPMI
can have ACPI tables describing them.
......@@ -52,7 +58,8 @@ their job correctly, the IPMI controller should be automatically
detected (via ACPI or SMBIOS tables) and should just work. Sadly,
many boards do not have this information. The driver attempts
standard defaults, but they may not work. If you fall into this
situation, you need to read the section below named 'The SI Driver'.
situation, you need to read the section below named 'The SI Driver' or
"The SMBus Driver" on how to hand-configure your system.
IPMI defines a standard watchdog timer. You can enable this with the
'IPMI Watchdog Timer' config option. If you compile the driver into
......@@ -97,7 +104,12 @@ driver, each open file for this device ties in to the message handler
as an IPMI user.
ipmi_si - A driver for various system interfaces. This supports KCS,
SMIC, and BT interfaces.
SMIC, and BT interfaces. Unless you have an SMBus interface or your
own custom interface, you probably need to use this.
ipmi_ssif - A driver for accessing BMCs on the SMBus. It uses the
I2C kernel driver's SMBus interfaces to send and receive IPMI messages
over the SMBus.
ipmi_watchdog - IPMI requires systems to have a very capable watchdog
timer. This driver implements the standard Linux watchdog timer
......@@ -476,6 +488,62 @@ for specifying an interface. Note that when removing an interface,
only the first three parameters (si type, address type, and address)
are used for the comparison. Any options are ignored for removing.
The SMBus Driver (SSIF)
-----------------------
The SMBus driver allows up to 4 SMBus devices to be configured in the
system. By default, the driver will only register with something it
finds in DMI or ACPI tables. You can change this
at module load time (for a module) with:
modprobe ipmi_ssif.o
addr=<i2caddr1>[,<i2caddr2>[,...]]
adapter=<adapter1>[,<adapter2>[...]]
dbg=<flags1>,<flags2>...
slave_addrs=<addr1>,<addr2>,...
[dbg_probe=1]
The addresses are normal I2C addresses. The adapter is the string
name of the adapter, as shown in /sys/class/i2c-adapter/i2c-<n>/name.
It is *NOT* i2c-<n> itself.
The debug flags are bit flags for each BMC found, they are:
IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8
Setting dbg_probe to 1 will enable debugging of the probing and
detection process for BMCs on the SMBusses.
The slave_addrs specifies the IPMI address of the local BMC. This is
usually 0x20 and the driver defaults to that, but in case it's not, it
can be specified when the driver starts up.
Discovering the IPMI compliant BMC on the SMBus can cause devices on
the I2C bus to fail. The SMBus driver writes a "Get Device ID" IPMI
message as a block write to the I2C bus and waits for a response.
This action can be detrimental to some I2C devices. It is highly
recommended that the known I2C address be given to the SMBus driver in
the smb_addr parameter unless you have DMI or ACPI data to tell the
driver what to use.
When compiled into the kernel, the addresses can be specified on the
kernel command line as:
ipmb_ssif.addr=<i2caddr1>[,<i2caddr2>[...]]
ipmi_ssif.adapter=<adapter1>[,<adapter2>[...]]
ipmi_ssif.dbg=<flags1>[,<flags2>[...]]
ipmi_ssif.dbg_probe=1
ipmi_ssif.slave_addrs=<addr1>[,<addr2>[...]]
These are the same options as on the module command line.
The I2C driver does not support non-blocking access or polling, so
this driver cannod to IPMI panic events, extend the watchdog at panic
time, or other panic-related IPMI functions without special kernel
patches and driver modifications. You can get those at the openipmi
web page.
The driver supports a hot add and remove of interfaces through the I2C
sysfs interface.
Other Pieces
------------
......
......@@ -62,6 +62,14 @@ config IPMI_SI_PROBE_DEFAULTS
only be available on older systems if the "ipmi_si_intf.trydefaults=1"
boot argument is passed.
config IPMI_SSIF
tristate 'IPMI SMBus handler (SSIF)'
select I2C
help
Provides a driver for a SMBus interface to a BMC, meaning that you
have a driver that must be accessed over an I2C bus instead of a
standard interface. This module requires I2C support.
config IPMI_WATCHDOG
tristate 'IPMI Watchdog Timer'
help
......
......@@ -7,5 +7,6 @@ ipmi_si-y := ipmi_si_intf.o ipmi_kcs_sm.o ipmi_smic_sm.o ipmi_bt_sm.o
obj-$(CONFIG_IPMI_HANDLER) += ipmi_msghandler.o
obj-$(CONFIG_IPMI_DEVICE_INTERFACE) += ipmi_devintf.o
obj-$(CONFIG_IPMI_SI) += ipmi_si.o
obj-$(CONFIG_IPMI_SSIF) += ipmi_ssif.o
obj-$(CONFIG_IPMI_WATCHDOG) += ipmi_watchdog.o
obj-$(CONFIG_IPMI_POWEROFF) += ipmi_poweroff.o
此差异已折叠。
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册