add support f421/f425

bsp/at32/at32f421-start/.config

+#
+# Automatically generated file; DO NOT EDIT.
+# RT-Thread Configuration
+#
+
+#
+# RT-Thread Kernel
+#
+CONFIG_RT_NAME_MAX=8
+# CONFIG_RT_USING_ARCH_DATA_TYPE is not set
+# CONFIG_RT_USING_SMART is not set
+# CONFIG_RT_USING_SMP is not set
+CONFIG_RT_ALIGN_SIZE=8
+# CONFIG_RT_THREAD_PRIORITY_8 is not set
+CONFIG_RT_THREAD_PRIORITY_32=y
+# CONFIG_RT_THREAD_PRIORITY_256 is not set
+CONFIG_RT_THREAD_PRIORITY_MAX=32
+CONFIG_RT_TICK_PER_SECOND=1000
+CONFIG_RT_USING_OVERFLOW_CHECK=y
+CONFIG_RT_USING_HOOK=y
+CONFIG_RT_HOOK_USING_FUNC_PTR=y
+CONFIG_RT_USING_IDLE_HOOK=y
+CONFIG_RT_IDLE_HOOK_LIST_SIZE=4
+CONFIG_IDLE_THREAD_STACK_SIZE=256
+CONFIG_RT_USING_TIMER_SOFT=y
+CONFIG_RT_TIMER_THREAD_PRIO=4
+CONFIG_RT_TIMER_THREAD_STACK_SIZE=512
+
+#
+# kservice optimization
+#
+# CONFIG_RT_KSERVICE_USING_STDLIB is not set
+# CONFIG_RT_KSERVICE_USING_TINY_SIZE is not set
+# CONFIG_RT_USING_TINY_FFS is not set
+# CONFIG_RT_KPRINTF_USING_LONGLONG is not set
+CONFIG_RT_DEBUG=y
+CONFIG_RT_DEBUG_COLOR=y
+# CONFIG_RT_DEBUG_INIT_CONFIG is not set
+# CONFIG_RT_DEBUG_THREAD_CONFIG is not set
+# CONFIG_RT_DEBUG_SCHEDULER_CONFIG is not set
+# CONFIG_RT_DEBUG_IPC_CONFIG is not set
+# CONFIG_RT_DEBUG_TIMER_CONFIG is not set
+# CONFIG_RT_DEBUG_IRQ_CONFIG is not set
+# CONFIG_RT_DEBUG_MEM_CONFIG is not set
+# CONFIG_RT_DEBUG_SLAB_CONFIG is not set
+# CONFIG_RT_DEBUG_MEMHEAP_CONFIG is not set
+# CONFIG_RT_DEBUG_MODULE_CONFIG is not set
+
+#
+# Inter-Thread communication
+#
+CONFIG_RT_USING_SEMAPHORE=y
+CONFIG_RT_USING_MUTEX=y
+CONFIG_RT_USING_EVENT=y
+CONFIG_RT_USING_MAILBOX=y
+CONFIG_RT_USING_MESSAGEQUEUE=y
+# CONFIG_RT_USING_SIGNALS is not set
+
+#
+# Memory Management
+#
+CONFIG_RT_PAGE_MAX_ORDER=11
+CONFIG_RT_USING_MEMPOOL=y
+CONFIG_RT_USING_SMALL_MEM=y
+# CONFIG_RT_USING_SLAB is not set
+CONFIG_RT_USING_MEMHEAP=y
+CONFIG_RT_MEMHEAP_FAST_MODE=y
+# CONFIG_RT_MEMHEAP_BEST_MODE is not set
+CONFIG_RT_USING_SMALL_MEM_AS_HEAP=y
+# CONFIG_RT_USING_MEMHEAP_AS_HEAP is not set
+# CONFIG_RT_USING_SLAB_AS_HEAP is not set
+# CONFIG_RT_USING_USERHEAP is not set
+# CONFIG_RT_USING_NOHEAP is not set
+# CONFIG_RT_USING_MEMTRACE is not set
+# CONFIG_RT_USING_HEAP_ISR is not set
+CONFIG_RT_USING_HEAP=y
+
+#
+# Kernel Device Object
+#
+CONFIG_RT_USING_DEVICE=y
+# CONFIG_RT_USING_DEVICE_OPS is not set
+# CONFIG_RT_USING_DM is not set
+# CONFIG_RT_USING_INTERRUPT_INFO is not set
+CONFIG_RT_USING_CONSOLE=y
+CONFIG_RT_CONSOLEBUF_SIZE=128
+CONFIG_RT_CONSOLE_DEVICE_NAME="uart1"
+CONFIG_RT_VER_NUM=0x50000
+# CONFIG_RT_USING_CACHE is not set
+# CONFIG_ARCH_ARM_BOOTWITH_FLUSH_CACHE is not set
+# CONFIG_ARCH_CPU_STACK_GROWS_UPWARD is not set
+CONFIG_RT_USING_CPU_FFS=y
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_ARM_CORTEX_M=y
+CONFIG_ARCH_ARM_CORTEX_M4=y
+
+#
+# RT-Thread Components
+#
+CONFIG_RT_USING_COMPONENTS_INIT=y
+CONFIG_RT_USING_USER_MAIN=y
+CONFIG_RT_MAIN_THREAD_STACK_SIZE=2048
+CONFIG_RT_MAIN_THREAD_PRIORITY=10
+# CONFIG_RT_USING_LEGACY is not set
+CONFIG_RT_USING_MSH=y
+CONFIG_RT_USING_FINSH=y
+CONFIG_FINSH_USING_MSH=y
+CONFIG_FINSH_THREAD_NAME="tshell"
+CONFIG_FINSH_THREAD_PRIORITY=20
+CONFIG_FINSH_THREAD_STACK_SIZE=4096
+CONFIG_FINSH_USING_HISTORY=y
+CONFIG_FINSH_HISTORY_LINES=5
+CONFIG_FINSH_USING_SYMTAB=y
+CONFIG_FINSH_CMD_SIZE=80
+CONFIG_MSH_USING_BUILT_IN_COMMANDS=y
+CONFIG_FINSH_USING_DESCRIPTION=y
+# CONFIG_FINSH_ECHO_DISABLE_DEFAULT is not set
+# CONFIG_FINSH_USING_AUTH is not set
+CONFIG_FINSH_ARG_MAX=10
+# CONFIG_RT_USING_DFS is not set
+# CONFIG_RT_USING_FAL is not set
+
+#
+# Device Drivers
+#
+CONFIG_RT_USING_DEVICE_IPC=y
+CONFIG_RT_UNAMED_PIPE_NUMBER=64
+# CONFIG_RT_USING_SYSTEM_WORKQUEUE is not set
+CONFIG_RT_USING_SERIAL=y
+CONFIG_RT_USING_SERIAL_V1=y
+# CONFIG_RT_USING_SERIAL_V2 is not set
+# CONFIG_RT_SERIAL_USING_DMA is not set
+CONFIG_RT_SERIAL_RB_BUFSZ=64
+# CONFIG_RT_USING_CAN is not set
+# CONFIG_RT_USING_HWTIMER is not set
+# CONFIG_RT_USING_CPUTIME is not set
+# CONFIG_RT_USING_I2C is not set
+# CONFIG_RT_USING_PHY is not set
+CONFIG_RT_USING_PIN=y
+# CONFIG_RT_USING_ADC is not set
+# CONFIG_RT_USING_DAC is not set
+# CONFIG_RT_USING_NULL is not set
+# CONFIG_RT_USING_ZERO is not set
+# CONFIG_RT_USING_RANDOM is not set
+# CONFIG_RT_USING_PWM is not set
+# CONFIG_RT_USING_MTD_NOR is not set
+# CONFIG_RT_USING_MTD_NAND is not set
+# CONFIG_RT_USING_PM is not set
+# CONFIG_RT_USING_FDT is not set
+# CONFIG_RT_USING_RTC is not set
+# CONFIG_RT_USING_SDIO is not set
+# CONFIG_RT_USING_SPI is not set
+# CONFIG_RT_USING_WDT is not set
+# CONFIG_RT_USING_AUDIO is not set
+# CONFIG_RT_USING_SENSOR is not set
+# CONFIG_RT_USING_TOUCH is not set
+# CONFIG_RT_USING_LCD is not set
+# CONFIG_RT_USING_HWCRYPTO is not set
+# CONFIG_RT_USING_PULSE_ENCODER is not set
+# CONFIG_RT_USING_INPUT_CAPTURE is not set
+# CONFIG_RT_USING_DEV_BUS is not set
+# CONFIG_RT_USING_WIFI is not set
+# CONFIG_RT_USING_VIRTIO is not set
+
+#
+# Using USB
+#
+# CONFIG_RT_USING_USB is not set
+# CONFIG_RT_USING_USB_HOST is not set
+# CONFIG_RT_USING_USB_DEVICE is not set
+
+#
+# C/C++ and POSIX layer
+#
+CONFIG_RT_LIBC_DEFAULT_TIMEZONE=8
+
+#
+# POSIX (Portable Operating System Interface) layer
+#
+# CONFIG_RT_USING_POSIX_FS is not set
+# CONFIG_RT_USING_POSIX_DELAY is not set
+# CONFIG_RT_USING_POSIX_CLOCK is not set
+# CONFIG_RT_USING_POSIX_TIMER is not set
+# CONFIG_RT_USING_PTHREADS is not set
+# CONFIG_RT_USING_MODULE is not set
+
+#
+# Interprocess Communication (IPC)
+#
+# CONFIG_RT_USING_POSIX_PIPE is not set
+# CONFIG_RT_USING_POSIX_MESSAGE_QUEUE is not set
+# CONFIG_RT_USING_POSIX_MESSAGE_SEMAPHORE is not set
+
+#
+# Socket is in the 'Network' category
+#
+# CONFIG_RT_USING_CPLUSPLUS is not set
+
+#
+# Network
+#
+# CONFIG_RT_USING_SAL is not set
+# CONFIG_RT_USING_NETDEV is not set
+# CONFIG_RT_USING_LWIP is not set
+# CONFIG_RT_USING_AT is not set
+
+#
+# Utilities
+#
+# CONFIG_RT_USING_RYM is not set
+# CONFIG_RT_USING_ULOG is not set
+# CONFIG_RT_USING_UTEST is not set
+# CONFIG_RT_USING_VAR_EXPORT is not set
+# CONFIG_RT_USING_RT_LINK is not set
+# CONFIG_RT_USING_VBUS is not set
+
+#
+# RT-Thread Utestcases
+#
+# CONFIG_RT_USING_UTESTCASES is not set
+
+#
+# RT-Thread online packages
+#
+
+#
+# IoT - internet of things
+#
+# CONFIG_PKG_USING_PAHOMQTT is not set
+# CONFIG_PKG_USING_WEBCLIENT is not set
+# CONFIG_PKG_USING_WEBNET is not set
+# CONFIG_PKG_USING_MONGOOSE is not set
+# CONFIG_PKG_USING_MYMQTT is not set
+# CONFIG_PKG_USING_MQTTCLIENT is not set
+# CONFIG_PKG_USING_WEBTERMINAL is not set
+# CONFIG_PKG_USING_CJSON is not set
+# CONFIG_PKG_USING_JSMN is not set
+# CONFIG_PKG_USING_LIBMODBUS is not set
+# CONFIG_PKG_USING_FREEMODBUS is not set
+# CONFIG_PKG_USING_LJSON is not set
+# CONFIG_PKG_USING_EZXML is not set
+# CONFIG_PKG_USING_NANOPB is not set
+
+#
+# Wi-Fi
+#
+
+#
+# Marvell WiFi
+#
+# CONFIG_PKG_USING_WLANMARVELL is not set
+
+#
+# Wiced WiFi
+#
+# CONFIG_PKG_USING_WLAN_WICED is not set
+# CONFIG_PKG_USING_RW007 is not set
+# CONFIG_PKG_USING_COAP is not set
+# CONFIG_PKG_USING_NOPOLL is not set
+# CONFIG_PKG_USING_NETUTILS is not set
+# CONFIG_PKG_USING_PPP_DEVICE is not set
+# CONFIG_PKG_USING_AT_DEVICE is not set
+# CONFIG_PKG_USING_ATSRV_SOCKET is not set
+# CONFIG_PKG_USING_WIZNET is not set
+
+#
+# IoT Cloud
+#
+# CONFIG_PKG_USING_ONENET is not set
+# CONFIG_PKG_USING_GAGENT_CLOUD is not set
+# CONFIG_PKG_USING_ALI_IOTKIT is not set
+# CONFIG_PKG_USING_AZURE is not set
+# CONFIG_PKG_USING_TENCENT_IOTHUB is not set
+# CONFIG_PKG_USING_JIOT-C-SDK is not set
+# CONFIG_PKG_USING_UCLOUD_IOT_SDK is not set
+# CONFIG_PKG_USING_NIMBLE is not set
+# CONFIG_PKG_USING_OTA_DOWNLOADER is not set
+# CONFIG_PKG_USING_IPMSG is not set
+# CONFIG_PKG_USING_LSSDP is not set
+# CONFIG_PKG_USING_AIRKISS_OPEN is not set
+# CONFIG_PKG_USING_LIBRWS is not set
+# CONFIG_PKG_USING_TCPSERVER is not set
+# CONFIG_PKG_USING_PROTOBUF_C is not set
+# CONFIG_PKG_USING_ONNX_PARSER is not set
+# CONFIG_PKG_USING_ONNX_BACKEND is not set
+# CONFIG_PKG_USING_DLT645 is not set
+# CONFIG_PKG_USING_QXWZ is not set
+# CONFIG_PKG_USING_SMTP_CLIENT is not set
+# CONFIG_PKG_USING_ABUP_FOTA is not set
+# CONFIG_PKG_USING_LIBCURL2RTT is not set
+# CONFIG_PKG_USING_CAPNP is not set
+# CONFIG_PKG_USING_RT_CJSON_TOOLS is not set
+# CONFIG_PKG_USING_AGILE_TELNET is not set
+
+#
+# security packages
+#
+# CONFIG_PKG_USING_MBEDTLS is not set
+# CONFIG_PKG_USING_libsodium is not set
+# CONFIG_PKG_USING_TINYCRYPT is not set
+# CONFIG_PKG_USING_TFM is not set
+
+#
+# language packages
+#
+# CONFIG_PKG_USING_LUA is not set
+# CONFIG_PKG_USING_JERRYSCRIPT is not set
+# CONFIG_PKG_USING_MICROPYTHON is not set
+
+#
+# multimedia packages
+#
+# CONFIG_PKG_USING_OPENMV is not set
+# CONFIG_PKG_USING_MUPDF is not set
+# CONFIG_PKG_USING_STEMWIN is not set
+# CONFIG_PKG_USING_WAVPLAYER is not set
+# CONFIG_PKG_USING_TJPGD is not set
+
+#
+# tools packages
+#
+# CONFIG_PKG_USING_CMBACKTRACE is not set
+# CONFIG_PKG_USING_EASYFLASH is not set
+# CONFIG_PKG_USING_EASYLOGGER is not set
+# CONFIG_PKG_USING_SYSTEMVIEW is not set
+# CONFIG_PKG_USING_RDB is not set
+# CONFIG_PKG_USING_QRCODE is not set
+# CONFIG_PKG_USING_ULOG_EASYFLASH is not set
+# CONFIG_PKG_USING_ADBD is not set
+# CONFIG_PKG_USING_COREMARK is not set
+# CONFIG_PKG_USING_DHRYSTONE is not set
+# CONFIG_PKG_USING_NR_MICRO_SHELL is not set
+# CONFIG_PKG_USING_CHINESE_FONT_LIBRARY is not set
+# CONFIG_PKG_USING_LUNAR_CALENDAR is not set
+# CONFIG_PKG_USING_BS8116A is not set
+
+#
+# system packages
+#
+# CONFIG_PKG_USING_GUIENGINE is not set
+# CONFIG_PKG_USING_PERSIMMON is not set
+# CONFIG_PKG_USING_CAIRO is not set
+# CONFIG_PKG_USING_PIXMAN is not set
+# CONFIG_PKG_USING_LWEXT4 is not set
+# CONFIG_PKG_USING_PARTITION is not set
+# CONFIG_PKG_USING_FAL is not set
+# CONFIG_PKG_USING_SQLITE is not set
+# CONFIG_PKG_USING_RTI is not set
+# CONFIG_PKG_USING_LITTLEVGL2RTT is not set
+# CONFIG_PKG_USING_CMSIS is not set
+# CONFIG_PKG_USING_DFS_YAFFS is not set
+# CONFIG_PKG_USING_LITTLEFS is not set
+# CONFIG_PKG_USING_THREAD_POOL is not set
+# CONFIG_PKG_USING_ROBOTS is not set
+# CONFIG_PKG_USING_EV is not set
+# CONFIG_PKG_USING_SYSWATCH is not set
+
+#
+# peripheral libraries and drivers
+#
+# CONFIG_PKG_USING_SENSORS_DRIVERS is not set
+# CONFIG_PKG_USING_REALTEK_AMEBA is not set
+# CONFIG_PKG_USING_SHT2X is not set
+# CONFIG_PKG_USING_SHT3X is not set
+# CONFIG_PKG_USING_STM32_SDIO is not set
+# CONFIG_PKG_USING_ICM20608 is not set
+# CONFIG_PKG_USING_U8G2 is not set
+# CONFIG_PKG_USING_BUTTON is not set
+# CONFIG_PKG_USING_PCF8574 is not set
+# CONFIG_PKG_USING_SX12XX is not set
+# CONFIG_PKG_USING_SIGNAL_LED is not set
+# CONFIG_PKG_USING_LEDBLINK is not set
+# CONFIG_PKG_USING_LITTLED is not set
+# CONFIG_PKG_USING_WM_LIBRARIES is not set
+# CONFIG_PKG_USING_KENDRYTE_SDK is not set
+# CONFIG_PKG_USING_INFRARED is not set
+# CONFIG_PKG_USING_ROSSERIAL is not set
+# CONFIG_PKG_USING_AGILE_BUTTON is not set
+# CONFIG_PKG_USING_AGILE_LED is not set
+# CONFIG_PKG_USING_AT24CXX is not set
+# CONFIG_PKG_USING_MOTIONDRIVER2RTT is not set
+# CONFIG_PKG_USING_AD7746 is not set
+# CONFIG_PKG_USING_PCA9685 is not set
+# CONFIG_PKG_USING_I2C_TOOLS is not set
+# CONFIG_PKG_USING_NRF24L01 is not set
+# CONFIG_PKG_USING_TOUCH_DRIVERS is not set
+# CONFIG_PKG_USING_MAX17048 is not set
+# CONFIG_PKG_USING_RPLIDAR is not set
+# CONFIG_PKG_USING_AS608 is not set
+# CONFIG_PKG_USING_RC522 is not set
+# CONFIG_PKG_USING_EMBARC_BSP is not set
+
+#
+# miscellaneous packages
+#
+# CONFIG_PKG_USING_LIBCSV is not set
+# CONFIG_PKG_USING_OPTPARSE is not set
+# CONFIG_PKG_USING_FASTLZ is not set
+# CONFIG_PKG_USING_MINILZO is not set
+# CONFIG_PKG_USING_QUICKLZ is not set
+# CONFIG_PKG_USING_MULTIBUTTON is not set
+# CONFIG_PKG_USING_FLEXIBLE_BUTTON is not set
+# CONFIG_PKG_USING_CANFESTIVAL is not set
+# CONFIG_PKG_USING_ZLIB is not set
+# CONFIG_PKG_USING_DSTR is not set
+# CONFIG_PKG_USING_TINYFRAME is not set
+# CONFIG_PKG_USING_KENDRYTE_DEMO is not set
+# CONFIG_PKG_USING_DIGITALCTRL is not set
+# CONFIG_PKG_USING_UPACKER is not set
+# CONFIG_PKG_USING_UPARAM is not set
+
+#
+# samples: kernel and components samples
+#
+# CONFIG_PKG_USING_KERNEL_SAMPLES is not set
+# CONFIG_PKG_USING_FILESYSTEM_SAMPLES is not set
+# CONFIG_PKG_USING_NETWORK_SAMPLES is not set
+# CONFIG_PKG_USING_PERIPHERAL_SAMPLES is not set
+# CONFIG_PKG_USING_HELLO is not set
+# CONFIG_PKG_USING_VI is not set
+# CONFIG_PKG_USING_NNOM is not set
+# CONFIG_PKG_USING_LIBANN is not set
+# CONFIG_PKG_USING_ELAPACK is not set
+# CONFIG_PKG_USING_ARMv7M_DWT is not set
+# CONFIG_PKG_USING_VT100 is not set
+# CONFIG_PKG_USING_ULAPACK is not set
+# CONFIG_PKG_USING_UKAL is not set
+CONFIG_SOC_FAMILY_AT32=y
+CONFIG_SOC_SERIES_AT32F421=y
+
+#
+# Hardware Drivers Config
+#
+CONFIG_SOC_AT32F421C8T7=y
+
+#
+# Onboard Peripheral Drivers
+#
+CONFIG_BSP_USING_SERIAL=y
+
+#
+# On-chip Peripheral Drivers
+#
+CONFIG_BSP_USING_GPIO=y
+# CONFIG_BSP_USING_ON_CHIP_FLASH is not set
+# CONFIG_BSP_USING_RTC is not set
+CONFIG_BSP_USING_UART=y
+CONFIG_BSP_USING_UART1=y
+# CONFIG_BSP_USING_UART2 is not set
+# CONFIG_BSP_USING_PWM is not set
+# CONFIG_BSP_USING_HWTIMER is not set
+# CONFIG_BSP_USING_SPI is not set
+# CONFIG_BSP_USING_I2C is not set
+# CONFIG_BSP_USING_ADC is not set

bsp/at32/at32f421-start/Kconfig

+mainmenu "RT-Thread Configuration"
+
+config BSP_DIR
+    string
+    option env="BSP_ROOT"
+    default "."
+
+config RTT_DIR
+    string
+    option env="RTT_ROOT"
+    default "../../.."
+
+config PKGS_DIR
+    string
+    option env="PKGS_ROOT"
+    default "packages"
+
+source "$RTT_DIR/Kconfig"
+source "$PKGS_DIR/Kconfig"
+source "../libraries/Kconfig"
+source "board/Kconfig"

bsp/at32/at32f421-start/README.md

+# AT32F421 AT-START 开发板 BSP 说明
+
+## 简介
+
+AT32F421 AT-START是雅特力推出的一款AT32F421系列的评估板，其搭载的MCU主要资源参数如下：
+
+| 硬件      | 描述          |
+| --------- | ------------- |
+| 芯片型号  | AT32F421C8T7  |
+| CPU       | ARM Cortex M4 |
+| 主频      | 120M          |
+| 片内SRAM  | 16K           |
+| 片内FLASH | 64K           |
+
+## 编译说明
+
+AT32F421-START板级包支持MDK4﹑MDK5﹑IAR开发环境和GCC编译器，以下是具体版本信息：
+
+| IDE/编译器 | 已测试版本                   |
+| ---------- | ---------------------------- |
+| MDK4       | MDK4.74                      |
+| MDK5       | MDK531                       |
+| IAR        | IAR8.20                      |
+| GCC        | GCC 5.4.1 20160919 (release) |
+
+## 板载资源
+
+- MCU：AT32F421C8T7，主频 120MHz，64KB FLASH ，16KB RAM
+- 常用外设
+  - LED：3个，（红色PF6、黄色PF7、绿色PB11）
+  - 按键：1个，KEY_USER（兼具唤醒功能，PA0)
+- 常用接口：插针串口J8
+- 调试接口，JLINK、板载的 AT-LINK SWD 下载
+
+## 外设支持
+
+本 BSP 目前对外设驱动的支持情况如下：
+
+| 驱动      | 支持情况 |            备注            |
+| --------- | -------- | :------------------------: |
+| UART      | 支持     | USART1/2                   |
+| GPIO      | 支持     | PA0...PF7                  |
+| IIC       | 支持     | GPIO模拟I2C                |
+| SPI       | 支持     | SPI1/2                     |
+| ADC       | 支持     | ADC1                       |
+| PWM       | 支持     | TMR1                       |
+| HWTIMER   | 支持     | TMR3                       |
+| WDT       | 支持     |                            |
+| RTC       | 支持     |                            |
+| FLASH     | 支持     |                            |
+
+### IO在板级支持包中的映射情况
+
+| IO号 | 板级包中的定义 |
+| ---- | -------------- |
+| PF6  | LED2           |
+| PF7  | LED3           |
+| PB11 | LED4           |
+| PA9  | USART1_TX      |
+| PA10 | USART1_RX      |
+| PA2  | USART2_TX      |
+| PA3  | USART2_RX      |
+| PA4  | SPI1_NSS       |
+| PA5  | SPI1_SCK       |
+| PA6  | SPI1_MISO      |
+| PA7  | SPI1_MOSI      |
+| PB12 | SPI2_NSS       |
+| PB13 | SPI2_SCK       |
+| PB14 | SPI2_MISO      |
+| PB15 | SPI2_MOSI      |
+| PB6  | I2C1_SCL       |
+| PB7  | I2C1_SDA       |
+| PA8  | PWM_TMR1_CH1   |
+| PA11 | PWM_TMR1_CH4   |
+| PA0  | ADC1_IN0       |
+| PA1  | ADC1_IN1       |
+| PA4  | ADC1_IN4       |
+| PA5  | ADC1_IN5       |
+| PA6  | ADC1_IN6       |
+
+## 使用说明
+
+    本章节是为刚接触 RT-Thread 的新手准备的使用说明，遵循简单的步骤即可将 RT-Thread 操作系统运行在该开发板上，看到实验效果 。
+
+### 快速上手
+
+本 BSP 为开发者提供 MDK4、MDK5 和 IAR 工程，并且支持 GCC 开发环境。下面以 MDK5 开发环境为例，介绍如何将系统运行起来。
+
+#### 硬件连接
+
+使用数据线连接开发板到 PC，打开电源开关。
+
+#### 编译下载
+
+双击 project.uvprojx 文件，打开 MDK5 工程，编译并下载程序到开发板。
+
+> 工程默认配置使用AT-LINK SWD下载程序，在通过AT-LINK SWD连接开发板的基础上，点击下载按钮即可下载程序到开发板
+
+#### 运行结果
+
+下载程序成功之后，系统会自动运行，观察开发板上 LED 的运行效果，LED2/3/4 会周期性闪烁。
+
+连接开发板对应串口到 PC , 在终端工具里打开相应的串口（115200-8-1-N），复位设备后，在串口上可以看到 RT-Thread 的输出信息:
+
+```bash
+ \ | /
+- RT -     Thread Operating System
+ / | \     5.0.0 build Jan 18 2023 09:19:32
+ 2006 - 2022 Copyright by RT-Thread team
+msh />
+```
+
+## 注意事项
+
+可在雅特力官方网站进行所需资料下载，如Keil_v5/Keil_v4/IAR等pack安装包和AT-START开发板原理图等（www.arterytek.com）
+
+## 联系人信息
+
+维护人:
+
+- [sheltonyu]
\ No newline at end of file

bsp/at32/at32f421-start/SConscript

+# for module compiling
+import os
+Import('RTT_ROOT')
+
+cwd = str(Dir('#'))
+objs = []
+list = os.listdir(cwd)
+
+for d in list:
+    path = os.path.join(cwd, d)
+    if os.path.isfile(os.path.join(path, 'SConscript')):
+        objs = objs + SConscript(os.path.join(d, 'SConscript'))
+
+Return('objs')

bsp/at32/at32f421-start/SConstruct

+import os
+import sys
+import rtconfig
+
+if os.getenv('RTT_ROOT'):
+    RTT_ROOT = os.getenv('RTT_ROOT')
+else:
+    RTT_ROOT = os.path.normpath(os.getcwd() + '/../../..')
+
+sys.path = sys.path + [os.path.join(RTT_ROOT, 'tools')]
+try:
+    from building import *
+except:
+    print('Cannot found RT-Thread root directory, please check RTT_ROOT')
+    print(RTT_ROOT)
+    exit(-1)
+
+TARGET = 'rtthread.' + rtconfig.TARGET_EXT
+
+DefaultEnvironment(tools=[])
+env = Environment(tools = ['mingw'],
+    AS = rtconfig.AS, ASFLAGS = rtconfig.AFLAGS,
+    CC = rtconfig.CC, CFLAGS = rtconfig.CFLAGS,
+    AR = rtconfig.AR, ARFLAGS = '-rc',
+    LINK = rtconfig.LINK, LINKFLAGS = rtconfig.LFLAGS)
+env.PrependENVPath('PATH', rtconfig.EXEC_PATH)
+
+if rtconfig.PLATFORM in ['iccarm']:
+    env.Replace(CCCOM = ['$CC $CFLAGS $CPPFLAGS $_CPPDEFFLAGS $_CPPINCFLAGS -o $TARGET $SOURCES'])
+    env.Replace(ARFLAGS = [''])
+    env.Replace(LINKCOM = env["LINKCOM"] + ' --map project.map')
+
+Export('RTT_ROOT')
+Export('rtconfig')
+
+SDK_ROOT = os.path.abspath('./')
+
+if os.path.exists(SDK_ROOT + '/libraries'):
+    libraries_path_prefix = SDK_ROOT + '/libraries'
+else:
+    libraries_path_prefix = os.path.dirname(SDK_ROOT) + '/libraries'
+
+SDK_LIB = libraries_path_prefix
+Export('SDK_LIB')
+
+# prepare building environment
+objs = PrepareBuilding(env, RTT_ROOT, has_libcpu=False)
+
+at32_library = 'AT32F421_Firmware_Library'
+rtconfig.BSP_LIBRARY_TYPE = at32_library
+
+# include libraries
+objs.extend(SConscript(os.path.join(libraries_path_prefix, at32_library, 'SConscript')))
+
+# include drivers
+objs.extend(SConscript(os.path.join(libraries_path_prefix, 'rt_drivers', 'SConscript')))
+
+# make a building
+DoBuilding(TARGET, objs)

bsp/at32/at32f421-start/applications/SConscript

+from building import *
+import os
+
+cwd = GetCurrentDir()
+src = Glob('*.c')
+CPPPATH = [cwd]
+
+group = DefineGroup('Applications', src, depend = [''], CPPPATH = CPPPATH)
+
+list = os.listdir(cwd)
+for item in list:
+    if os.path.isfile(os.path.join(cwd, item, 'SConscript')):
+        group = group + SConscript(os.path.join(item, 'SConscript'))
+
+Return('group')

bsp/at32/at32f421-start/applications/main.c

+/*
+ * Copyright (c) 2006-2021, RT-Thread Development Team
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Change Logs:
+ * Date           Author       Notes
+ * 2023-01-31     shelton      first version
+ */
+
+#include <rtthread.h>
+#include <rtdevice.h>
+#include "drv_common.h"
+#include "drv_gpio.h"
+
+/* defined the led2 pin: pf6 */
+#define LED2_PIN    GET_PIN(F, 6)
+/* defined the led3 pin: pf7 */
+#define LED3_PIN    GET_PIN(F, 7)
+/* defined the led4 pin: pb11 */
+#define LED4_PIN    GET_PIN(B, 11)
+
+int main(void)
+{
+    rt_uint32_t speed = 200;
+    /* set led2 pin mode to output */
+    rt_pin_mode(LED2_PIN, PIN_MODE_OUTPUT);
+    /* set led3 pin mode to output */
+    rt_pin_mode(LED3_PIN, PIN_MODE_OUTPUT);
+    /* set led4 pin mode to output */
+    rt_pin_mode(LED4_PIN, PIN_MODE_OUTPUT);
+
+    while (1)
+    {
+        rt_pin_write(LED2_PIN, PIN_LOW);
+        rt_thread_mdelay(speed);
+        rt_pin_write(LED3_PIN, PIN_LOW);
+        rt_thread_mdelay(speed);
+        rt_pin_write(LED4_PIN, PIN_LOW);
+        rt_thread_mdelay(speed);
+        rt_pin_write(LED2_PIN, PIN_HIGH);
+        rt_thread_mdelay(speed);
+        rt_pin_write(LED3_PIN, PIN_HIGH);
+        rt_thread_mdelay(speed);
+        rt_pin_write(LED4_PIN, PIN_HIGH);
+        rt_thread_mdelay(speed);
+    }
+}

bsp/at32/at32f421-start/board/Kconfig

+menu "Hardware Drivers Config"
+
+config SOC_AT32F421C8T7
+    bool
+    select SOC_SERIES_AT32F421
+    select RT_USING_COMPONENTS_INIT
+    select RT_USING_USER_MAIN
+    default y
+
+menu "Onboard Peripheral Drivers"
+
+    config BSP_USING_SERIAL
+        bool "Enable USART (uart1)"
+        select BSP_USING_UART
+        select BSP_USING_UART1
+        default y
+
+endmenu
+
+menu "On-chip Peripheral Drivers"
+
+    config BSP_USING_GPIO
+        bool "Enable GPIO"
+        select RT_USING_PIN
+        default y
+
+    config BSP_USING_ON_CHIP_FLASH
+        bool "Enable on-chip FLASH"
+        default n
+
+    menuconfig BSP_USING_RTC
+        bool "Enable RTC"
+        select RT_USING_RTC
+        default n
+        if BSP_USING_RTC
+            choice
+                prompt "Select clock source"
+                default BSP_RTC_USING_LEXT
+
+                config BSP_RTC_USING_LEXT
+                    bool "RTC USING LEXT"
+
+                config BSP_RTC_USING_LICK
+                    bool "RTC USING LICK"
+            endchoice
+        endif
+
+    menuconfig BSP_USING_UART
+        bool "Enable UART"
+        default y
+        select RT_USING_SERIAL
+        if BSP_USING_UART
+            config BSP_USING_UART1
+                bool "Enable UART1"
+                default y
+
+            config BSP_UART1_RX_USING_DMA
+                bool "Enable UART1 RX DMA"
+                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
+                default n
+
+            config BSP_USING_UART2
+                bool "Enable UART2"
+                default n
+
+            config BSP_UART2_RX_USING_DMA
+                bool "Enable UART2 RX DMA"
+                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
+                default n
+        endif
+
+    menuconfig BSP_USING_PWM
+        bool "Enable PWM"
+        default n
+        select RT_USING_PWM
+        if BSP_USING_PWM
+        menuconfig BSP_USING_PWM1
+            bool "Enable timer1 output pwm"
+            default n
+            if BSP_USING_PWM1
+                config BSP_USING_PWM1_CH1
+                    bool "Enable PWM1 channel1"
+                    default n
+
+                config BSP_USING_PWM1_CH4
+                    bool "Enable PWM1 channel4"
+                    default n
+            endif
+        endif
+
+    menuconfig BSP_USING_HWTIMER
+        bool "Enable HWTIMER"
+        default n
+        select RT_USING_HWTIMER
+        if BSP_USING_HWTIMER
+        config BSP_USING_HWTMR3
+            bool "Enable hardware timer3"
+            default n
+        endif
+
+    menuconfig BSP_USING_SPI
+        bool "Enable SPI BUS"
+        default n
+        select RT_USING_SPI
+        if BSP_USING_SPI
+            config BSP_USING_SPI1
+                bool "Enable SPI1 BUS"
+                default n
+
+            config BSP_SPI1_TX_USING_DMA
+                bool "Enable SPI1 TX DMA"
+                depends on BSP_USING_SPI1
+                default n
+
+            config BSP_SPI1_RX_USING_DMA
+                bool "Enable SPI1 RX DMA"
+                depends on BSP_USING_SPI1
+                select BSP_SPI1_TX_USING_DMA
+                default n
+
+            config BSP_USING_SPI2
+                bool "Enable SPI2 BUS"
+                default n
+
+            config BSP_SPI2_TX_USING_DMA
+                bool "Enable SPI2 TX DMA"
+                depends on BSP_USING_SPI2
+                default n
+
+            config BSP_SPI2_RX_USING_DMA
+                bool "Enable SPI2 RX DMA"
+                depends on BSP_USING_SPI2
+                select BSP_SPI2_TX_USING_DMA
+                default n
+        endif
+
+    menuconfig BSP_USING_I2C
+        bool "Enable I2C BUS (software simulation)"
+        default n
+        select RT_USING_I2C
+        select RT_USING_I2C_BITOPS
+        select RT_USING_PIN
+        if BSP_USING_I2C
+            config BSP_USING_I2C1
+                bool "Enable I2C1 BUS"
+                if BSP_USING_I2C1
+                    config BSP_I2C1_SCL_PIN
+                        int "i2c1 scl pin number"
+                        range 0 63
+                        default 22
+                    config BSP_I2C1_SDA_PIN
+                        int "I2C1 sda pin number"
+                        range 0 63
+                        default 23
+                endif
+            config BSP_USING_I2C2
+                bool "Enable I2C2 BUS"
+                if BSP_USING_I2C2
+                    config BSP_I2C2_SCL_PIN
+                        int "i2c2 scl pin number"
+                        range 0 63
+                        default 26
+                    config BSP_I2C2_SDA_PIN
+                        int "I2C2 sda pin number"
+                        range 0 63
+                        default 27
+                endif
+        endif
+
+    menuconfig BSP_USING_ADC
+        bool "Enable ADC"
+        default n
+        select RT_USING_ADC
+        if BSP_USING_ADC
+            config BSP_USING_ADC1
+                bool "Enable ADC1"
+                default n
+        endif
+endmenu
+
+endmenu

bsp/at32/at32f421-start/board/SConscript

+import os
+import rtconfig
+from building import *
+
+Import('SDK_LIB')
+
+cwd = GetCurrentDir()
+
+# add general drivers
+src = Split('''
+src/board.c
+src/at32_msp.c
+''')
+
+path = [cwd]
+path += [cwd + '/inc']
+
+startup_path_prefix = SDK_LIB
+
+if rtconfig.PLATFORM in ['gcc']:
+    src += [startup_path_prefix + '/AT32F421_Firmware_Library/cmsis/cm4/device_support/startup/gcc/startup_at32f421.s']
+elif rtconfig.PLATFORM in ['armcc', 'armclang']:
+    src += [startup_path_prefix + '/AT32F421_Firmware_Library/cmsis/cm4/device_support/startup/mdk/startup_at32f421.s']
+elif rtconfig.PLATFORM in ['iccarm']:
+    src += [startup_path_prefix + '/AT32F421_Firmware_Library/cmsis/cm4/device_support/startup/iar/startup_at32f421.s']
+
+CPPDEFINES = ['AT32F421C8T7']
+group = DefineGroup('Drivers', src, depend = [''], CPPPATH = path, CPPDEFINES = CPPDEFINES)
+Return('group')

bsp/at32/at32f421-start/board/inc/at32_msp.h

+/*
+ * Copyright (c) 2006-2018, RT-Thread Development Team
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Change Logs:
+ * Date           Author       Notes
+ * 2023-01-31     shelton      first version
+ */
+
+#ifndef __AT32_MSP_H__
+#define __AT32_MSP_H__
+
+void at32_msp_usart_init(void *instance);
+void at32_msp_spi_init(void *instance);
+void at32_msp_tmr_init(void *instance);
+void at32_msp_adc_init(void *instance);
+void at32_msp_hwtmr_init(void *instance);
+
+#endif /* __AT32_MSP_H__ */

bsp/at32/at32f421-start/board/inc/at32f421_conf.h

+/**
+  **************************************************************************
+  * @file     at32f421_conf.h
+  * @brief    at32f421 config header file
+  **************************************************************************
+  *                       Copyright notice & Disclaimer
+  *
+  * The software Board Support Package (BSP) that is made available to
+  * download from Artery official website is the copyrighted work of Artery.
+  * Artery authorizes customers to use, copy, and distribute the BSP
+  * software and its related documentation for the purpose of design and
+  * development in conjunction with Artery microcontrollers. Use of the
+  * software is governed by this copyright notice and the following disclaimer.
+  *
+  * THIS SOFTWARE IS PROVIDED ON "AS IS" BASIS WITHOUT WARRANTIES,
+  * GUARANTEES OR REPRESENTATIONS OF ANY KIND. ARTERY EXPRESSLY DISCLAIMS,
+  * TO THE FULLEST EXTENT PERMITTED BY LAW, ALL EXPRESS, IMPLIED OR
+  * STATUTORY OR OTHER WARRANTIES, GUARANTEES OR REPRESENTATIONS,
+  * INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY,
+  * FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT.
+  *
+  **************************************************************************
+  */
+
+/* define to prevent recursive inclusion -------------------------------------*/
+#ifndef __AT32F421_CONF_H
+#define __AT32F421_CONF_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+  * @brief in the following line adjust the value of high speed exernal crystal (hext)
+  * used in your application
+  *
+  * tip: to avoid modifying this file each time you need to use different hext, you
+  *      can define the hext value in your toolchain compiler preprocessor.
+  *
+  */
+#if !defined  HEXT_VALUE
+#define HEXT_VALUE               ((uint32_t)8000000) /*!< value of the high speed exernal crystal in hz */
+#endif
+
+/**
+  * @brief in the following line adjust the high speed exernal crystal (hext) startup
+  * timeout value
+  */
+#define HEXT_STARTUP_TIMEOUT     ((uint16_t)0x3000) /*!< time out for hext start up */
+#define HICK_VALUE               ((uint32_t)8000000) /*!< value of the high speed internal clock in hz */
+
+/* module define -------------------------------------------------------------*/
+#define CRM_MODULE_ENABLED
+#define TMR_MODULE_ENABLED
+#define ERTC_MODULE_ENABLED
+#define GPIO_MODULE_ENABLED
+#define I2C_MODULE_ENABLED
+#define USART_MODULE_ENABLED
+#define PWC_MODULE_ENABLED
+#define ADC_MODULE_ENABLED
+#define SPI_MODULE_ENABLED
+#define DMA_MODULE_ENABLED
+#define DEBUG_MODULE_ENABLED
+#define FLASH_MODULE_ENABLED
+#define CRC_MODULE_ENABLED
+#define WWDT_MODULE_ENABLED
+#define WDT_MODULE_ENABLED
+#define EXINT_MODULE_ENABLED
+#define MISC_MODULE_ENABLED
+#define SCFG_MODULE_ENABLED
+
+/* includes ------------------------------------------------------------------*/
+#ifdef CRM_MODULE_ENABLED
+#include "at32f421_crm.h"
+#endif
+#ifdef TMR_MODULE_ENABLED
+#include "at32f421_tmr.h"
+#endif
+#ifdef ERTC_MODULE_ENABLED
+#include "at32f421_ertc.h"
+#endif
+#ifdef GPIO_MODULE_ENABLED
+#include "at32f421_gpio.h"
+#endif
+#ifdef I2C_MODULE_ENABLED
+#include "at32f421_i2c.h"
+#endif
+#ifdef USART_MODULE_ENABLED
+#include "at32f421_usart.h"
+#endif
+#ifdef PWC_MODULE_ENABLED
+#include "at32f421_pwc.h"
+#endif
+#ifdef ADC_MODULE_ENABLED
+#include "at32f421_adc.h"
+#endif
+#ifdef SPI_MODULE_ENABLED
+#include "at32f421_spi.h"
+#endif
+#ifdef DMA_MODULE_ENABLED
+#include "at32f421_dma.h"
+#endif
+#ifdef DEBUG_MODULE_ENABLED
+#include "at32f421_debug.h"
+#endif
+#ifdef FLASH_MODULE_ENABLED
+#include "at32f421_flash.h"
+#endif
+#ifdef CRC_MODULE_ENABLED
+#include "at32f421_crc.h"
+#endif
+#ifdef WWDT_MODULE_ENABLED
+#include "at32f421_wwdt.h"
+#endif
+#ifdef WDT_MODULE_ENABLED
+#include "at32f421_wdt.h"
+#endif
+#ifdef EXINT_MODULE_ENABLED
+#include "at32f421_exint.h"
+#endif
+#ifdef MISC_MODULE_ENABLED
+#include "at32f421_misc.h"
+#endif
+#ifdef SCFG_MODULE_ENABLED
+#include "at32f421_scfg.h"
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+
+

bsp/at32/at32f421-start/board/inc/board.h

+/*
+ * Copyright (c) 2006-2021, RT-Thread Development Team
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Change Logs:
+ * Date           Author       Notes
+ * 2023-01-31     shelton      first version
+ */
+
+#ifndef __BOARD_H__
+#define __BOARD_H__
+
+#include <rtthread.h>
+#include "at32f421.h"
+#include "at32_msp.h"
+#include "drv_common.h"
+#include "drv_gpio.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#define AT32_FLASH_START_ADRESS         ((uint32_t)0x08000000)
+#define FLASH_PAGE_SIZE                 (1 * 1024)
+#define AT32_FLASH_SIZE                 (64 * 1024)
+#define AT32_FLASH_END_ADDRESS          ((uint32_t)(AT32_FLASH_START_ADRESS + AT32_FLASH_SIZE))
+
+/* internal sram memory size[kbytes] <16>, default: 16*/
+#define AT32_SRAM_SIZE                  16
+#define AT32_SRAM_END                   (0x20000000 + AT32_SRAM_SIZE * 1024)
+
+#if defined(__ARMCC_VERSION)
+extern int Image$$RW_IRAM1$$ZI$$Limit;
+#define HEAP_BEGIN                      ((void *)&Image$$RW_IRAM1$$ZI$$Limit)
+#elif __ICCARM__
+#pragma section="CSTACK"
+#define HEAP_BEGIN                      (__segment_end("CSTACK"))
+#else
+extern int __bss_end;
+#define HEAP_BEGIN                      ((void *)&__bss_end)
+#endif
+
+#define HEAP_END                        AT32_SRAM_END
+
+void system_clock_config(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __BOARD_H__ */

bsp/at32/at32f421-start/board/linker_scripts/link.icf

+/*###ICF### Section handled by ICF editor, don't touch! ****/
+/*-Editor annotation file-*/
+/* IcfEditorFile="$TOOLKIT_DIR$\config\ide\IcfEditor\cortex_v1_0.xml" */
+/*-Specials-*/
+define symbol __ICFEDIT_intvec_start__ = 0x08000000;
+/*-Memory Regions-*/
+define symbol __ICFEDIT_region_ROM_start__ = 0x08000000;
+define symbol __ICFEDIT_region_ROM_end__   = 0x0800FFFF;
+define symbol __ICFEDIT_region_RAM_start__ = 0x20000000;
+define symbol __ICFEDIT_region_RAM_end__   = 0x20003FFF;
+/*-Sizes-*/
+define symbol __ICFEDIT_size_cstack__ = 0x0400;
+define symbol __ICFEDIT_size_heap__   = 0x0000;
+/**** End of ICF editor section. ###ICF###*/
+
+define memory mem with size = 4G;
+define region ROM_region      = mem:[from __ICFEDIT_region_ROM_start__   to __ICFEDIT_region_ROM_end__];
+define region RAM_region      = mem:[from __ICFEDIT_region_RAM_start__   to __ICFEDIT_region_RAM_end__];
+
+define block CSTACK    with alignment = 8, size = __ICFEDIT_size_cstack__   { };
+
+initialize by copy { readwrite };
+do not initialize  { section .noinit };
+
+place at address mem:__ICFEDIT_intvec_start__ { readonly section .intvec };
+
+place in ROM_region   { readonly };
+place in RAM_region   { readwrite, last block CSTACK};

bsp/at32/at32f421-start/board/linker_scripts/link.lds

+/*
+ * linker script for AT32 with GNU ld
+ */
+
+/* Program Entry, set to mark it as "used" and avoid gc */
+MEMORY
+{
+    ROM (rx) : ORIGIN = 0x08000000, LENGTH = 64k /* 64KB flash */
+    RAM (rw) : ORIGIN = 0x20000000, LENGTH = 16k /* 16K sram */
+}
+ENTRY(Reset_Handler)
+_system_stack_size = 0x200;
+
+SECTIONS
+{
+    .text :
+    {
+        . = ALIGN(4);
+        _stext = .;
+        KEEP(*(.isr_vector))            /* Startup code */
+
+        . = ALIGN(4);
+        *(.text)                        /* remaining code */
+        *(.text.*)                      /* remaining code */
+        *(.rodata)                      /* read-only data (constants) */
+        *(.rodata*)
+        *(.glue_7)
+        *(.glue_7t)
+        *(.gnu.linkonce.t*)
+
+        /* section information for finsh shell */
+        . = ALIGN(4);
+        __fsymtab_start = .;
+        KEEP(*(FSymTab))
+        __fsymtab_end = .;
+
+        . = ALIGN(4);
+        __vsymtab_start = .;
+        KEEP(*(VSymTab))
+        __vsymtab_end = .;
+
+        /* section information for initial. */
+        . = ALIGN(4);
+        __rt_init_start = .;
+        KEEP(*(SORT(.rti_fn*)))
+        __rt_init_end = .;
+
+        . = ALIGN(4);
+
+        PROVIDE(__ctors_start__ = .);
+        KEEP (*(SORT(.init_array.*)))
+        KEEP (*(.init_array))
+        PROVIDE(__ctors_end__ = .);
+
+        . = ALIGN(4);
+
+        _etext = .;
+    } > ROM = 0
+
+    /* .ARM.exidx is sorted, so has to go in its own output section.  */
+    __exidx_start = .;
+    .ARM.exidx :
+    {
+        *(.ARM.exidx* .gnu.linkonce.armexidx.*)
+
+        /* This is used by the startup in order to initialize the .data secion */
+        _sidata = .;
+    } > ROM
+    __exidx_end = .;
+
+    /* .data section which is used for initialized data */
+
+    .data : AT (_sidata)
+    {
+        . = ALIGN(4);
+        /* This is used by the startup in order to initialize the .data secion */
+        _sdata = . ;
+
+        *(.data)
+        *(.data.*)
+        *(.gnu.linkonce.d*)
+
+        PROVIDE(__dtors_start__ = .);
+        KEEP(*(SORT(.dtors.*)))
+        KEEP(*(.dtors))
+        PROVIDE(__dtors_end__ = .);
+
+        . = ALIGN(4);
+        /* This is used by the startup in order to initialize the .data secion */
+        _edata = . ;
+    } >RAM
+
+    .stack :
+    {
+        . = ALIGN(4);
+        _sstack = .;
+        . = . + _system_stack_size;
+        . = ALIGN(4);
+        _estack = .;
+    } >RAM
+
+    __bss_start = .;
+    .bss :
+    {
+        . = ALIGN(4);
+        /* This is used by the startup in order to initialize the .bss secion */
+        _sbss = .;
+
+        *(.bss)
+        *(.bss.*)
+        *(COMMON)
+
+        . = ALIGN(4);
+        /* This is used by the startup in order to initialize the .bss secion */
+        _ebss = . ;
+
+        *(.bss.init)
+    } > RAM
+    __bss_end = .;
+
+    _end = .;
+
+    /* Stabs debugging sections.  */
+    .stab          0 : { *(.stab) }
+    .stabstr       0 : { *(.stabstr) }
+    .stab.excl     0 : { *(.stab.excl) }
+    .stab.exclstr  0 : { *(.stab.exclstr) }
+    .stab.index    0 : { *(.stab.index) }
+    .stab.indexstr 0 : { *(.stab.indexstr) }
+    .comment       0 : { *(.comment) }
+    /* DWARF debug sections.
+     * Symbols in the DWARF debugging sections are relative to the beginning
+     * of the section so we begin them at 0.  */
+    /* DWARF 1 */
+    .debug          0 : { *(.debug) }
+    .line           0 : { *(.line) }
+    /* GNU DWARF 1 extensions */
+    .debug_srcinfo  0 : { *(.debug_srcinfo) }
+    .debug_sfnames  0 : { *(.debug_sfnames) }
+    /* DWARF 1.1 and DWARF 2 */
+    .debug_aranges  0 : { *(.debug_aranges) }
+    .debug_pubnames 0 : { *(.debug_pubnames) }
+    /* DWARF 2 */
+    .debug_info     0 : { *(.debug_info .gnu.linkonce.wi.*) }
+    .debug_abbrev   0 : { *(.debug_abbrev) }
+    .debug_line     0 : { *(.debug_line) }
+    .debug_frame    0 : { *(.debug_frame) }
+    .debug_str      0 : { *(.debug_str) }
+    .debug_loc      0 : { *(.debug_loc) }
+    .debug_macinfo  0 : { *(.debug_macinfo) }
+    /* SGI/MIPS DWARF 2 extensions */
+    .debug_weaknames 0 : { *(.debug_weaknames) }
+    .debug_funcnames 0 : { *(.debug_funcnames) }
+    .debug_typenames 0 : { *(.debug_typenames) }
+    .debug_varnames  0 : { *(.debug_varnames) }
+}

bsp/at32/at32f421-start/board/linker_scripts/link.sct

+; *************************************************************
+; *** Scatter-Loading Description File generated by uVision ***
+; *************************************************************
+
+LR_IROM1 0x08000000 0x00010000  {    ; load region size_region
+  ER_IROM1 0x08000000 0x00010000  {  ; load address = execution address
+   *.o (RESET, +First)
+   *(InRoot$$Sections)
+   .ANY (+RO)
+  }
+  RW_IRAM1 0x20000000 0x00004000  {  ; RW data
+   .ANY (+RW +ZI)
+  }
+}
+

bsp/at32/at32f421-start/board/src/at32_msp.c

+/*
+ * Copyright (c) 2006-2018, RT-Thread Development Team
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Change Logs:
+ * Date           Author       Notes
+ * 2023-01-31     shelton      first version
+ */
+
+#include <rtthread.h>
+#include "at32f421.h"
+#include "at32_msp.h"
+
+#ifdef BSP_USING_UART
+void at32_msp_usart_init(void *instance)
+{
+    gpio_init_type gpio_init_struct;
+    usart_type *usart_x = (usart_type *)instance;
+
+    gpio_default_para_init(&gpio_init_struct);
+    gpio_init_struct.gpio_drive_strength = GPIO_DRIVE_STRENGTH_STRONGER;
+#ifdef BSP_USING_UART1
+    if(USART1 == usart_x)
+    {
+        crm_periph_clock_enable(CRM_USART1_PERIPH_CLOCK, TRUE);
+        crm_periph_clock_enable(CRM_GPIOA_PERIPH_CLOCK, TRUE);
+
+        gpio_init_struct.gpio_mode = GPIO_MODE_MUX;
+        gpio_init_struct.gpio_out_type = GPIO_OUTPUT_PUSH_PULL;
+        gpio_init_struct.gpio_pull = GPIO_PULL_NONE;
+        gpio_init_struct.gpio_pins = GPIO_PINS_9;
+        gpio_init(GPIOA, &gpio_init_struct);
+
+        gpio_init_struct.gpio_pins = GPIO_PINS_10;
+        gpio_init(GPIOA, &gpio_init_struct);
+
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE9, GPIO_MUX_1);
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE10, GPIO_MUX_1);
+    }
+#endif
+#ifdef BSP_USING_UART2
+    if(USART2 == usart_x)
+    {
+        crm_periph_clock_enable(CRM_USART2_PERIPH_CLOCK, TRUE);
+        crm_periph_clock_enable(CRM_GPIOA_PERIPH_CLOCK, TRUE);
+
+        gpio_init_struct.gpio_mode = GPIO_MODE_MUX;
+        gpio_init_struct.gpio_out_type = GPIO_OUTPUT_PUSH_PULL;
+        gpio_init_struct.gpio_pull = GPIO_PULL_NONE;
+        gpio_init_struct.gpio_pins = GPIO_PINS_2;
+        gpio_init(GPIOA, &gpio_init_struct);
+
+        gpio_init_struct.gpio_pins = GPIO_PINS_3;
+        gpio_init(GPIOA, &gpio_init_struct);
+
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE2, GPIO_MUX_1);
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE3, GPIO_MUX_1);
+    }
+#endif
+    /* add others */
+}
+#endif /* BSP_USING_SERIAL */
+
+#ifdef BSP_USING_SPI
+void at32_msp_spi_init(void *instance)
+{
+    gpio_init_type gpio_init_struct;
+    spi_type *spi_x = (spi_type *)instance;
+
+    gpio_default_para_init(&gpio_init_struct);
+    gpio_init_struct.gpio_drive_strength = GPIO_DRIVE_STRENGTH_STRONGER;
+#ifdef BSP_USING_SPI1
+    if(SPI1 == spi_x)
+    {
+        crm_periph_clock_enable(CRM_SPI1_PERIPH_CLOCK, TRUE);
+        crm_periph_clock_enable(CRM_GPIOA_PERIPH_CLOCK, TRUE);
+
+        gpio_init_struct.gpio_mode = GPIO_MODE_OUTPUT;
+        gpio_init_struct.gpio_out_type = GPIO_OUTPUT_PUSH_PULL;
+        gpio_init_struct.gpio_pull = GPIO_PULL_NONE;
+        gpio_init_struct.gpio_pins = GPIO_PINS_4;
+        gpio_init(GPIOA, &gpio_init_struct);
+
+        gpio_init_struct.gpio_mode = GPIO_MODE_MUX;
+        gpio_init_struct.gpio_pins = GPIO_PINS_5 | GPIO_PINS_6 | GPIO_PINS_7;
+        gpio_init(GPIOA, &gpio_init_struct);
+
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE5, GPIO_MUX_0);
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE6, GPIO_MUX_0);
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE7, GPIO_MUX_0);
+    }
+#endif
+#ifdef BSP_USING_SPI2
+    if(SPI2 == spi_x)
+    {
+        crm_periph_clock_enable(CRM_SPI2_PERIPH_CLOCK, TRUE);
+        crm_periph_clock_enable(CRM_GPIOB_PERIPH_CLOCK, TRUE);
+
+        gpio_init_struct.gpio_mode = GPIO_MODE_OUTPUT;
+        gpio_init_struct.gpio_out_type = GPIO_OUTPUT_PUSH_PULL;
+        gpio_init_struct.gpio_pull = GPIO_PULL_NONE;
+        gpio_init_struct.gpio_pins = GPIO_PINS_12;
+        gpio_init(GPIOB, &gpio_init_struct);
+
+        gpio_init_struct.gpio_mode = GPIO_MODE_MUX;
+        gpio_init_struct.gpio_pins = GPIO_PINS_13 | GPIO_PINS_14 | GPIO_PINS_15;
+        gpio_init(GPIOB, &gpio_init_struct);
+
+        gpio_pin_mux_config(GPIOB, GPIO_PINS_SOURCE13, GPIO_MUX_0);
+        gpio_pin_mux_config(GPIOB, GPIO_PINS_SOURCE14, GPIO_MUX_0);
+        gpio_pin_mux_config(GPIOB, GPIO_PINS_SOURCE15, GPIO_MUX_0);
+    }
+#endif
+    /* add others */
+}
+#endif /* BSP_USING_SPI */
+
+#ifdef BSP_USING_PWM
+void at32_msp_tmr_init(void *instance)
+{
+    gpio_init_type gpio_init_struct;
+    tmr_type *tmr_x = (tmr_type *)instance;
+
+    gpio_default_para_init(&gpio_init_struct);
+    gpio_init_struct.gpio_drive_strength = GPIO_DRIVE_STRENGTH_STRONGER;
+    if(tmr_x == TMR1)
+    {
+        /* tmr1 clock enable */
+        crm_periph_clock_enable(CRM_TMR1_PERIPH_CLOCK, TRUE);
+        /* gpioa clock enable */
+        crm_periph_clock_enable(CRM_GPIOA_PERIPH_CLOCK, TRUE);
+
+        /* gpioa configuration: tmr1 channel1 and channel4 as alternate function push-pull */
+        gpio_init_struct.gpio_mode = GPIO_MODE_MUX;
+        gpio_init_struct.gpio_out_type = GPIO_OUTPUT_PUSH_PULL;
+        gpio_init_struct.gpio_pull = GPIO_PULL_NONE;
+        gpio_init_struct.gpio_pins = GPIO_PINS_8 | GPIO_PINS_11;
+        gpio_init(GPIOA, &gpio_init_struct);
+
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE8, GPIO_MUX_2);
+        gpio_pin_mux_config(GPIOA, GPIO_PINS_SOURCE11, GPIO_MUX_2);
+    }
+    /* add others */
+}
+#endif /* BSP_USING_PWM */
+
+#ifdef BSP_USING_ADC
+void at32_msp_adc_init(void *instance)
+{
+    gpio_init_type gpio_init_struct;
+    adc_type *adc_x = (adc_type *)instance;
+
+    gpio_default_para_init(&gpio_init_struct);
+    gpio_init_struct.gpio_drive_strength = GPIO_DRIVE_STRENGTH_STRONGER;
+#ifdef BSP_USING_ADC1
+    if(adc_x == ADC1)
+    {
+        /* adc1 & gpio clock enable */
+        crm_periph_clock_enable(CRM_ADC1_PERIPH_CLOCK, TRUE);
+        crm_periph_clock_enable(CRM_GPIOA_PERIPH_CLOCK, TRUE);
+
+        /* configure adc channel as analog input */
+        gpio_init_struct.gpio_pins = GPIO_PINS_0 | GPIO_PINS_1 | GPIO_PINS_4 | GPIO_PINS_5 | GPIO_PINS_6;
+        gpio_init_struct.gpio_mode = GPIO_MODE_ANALOG;
+        gpio_init(GPIOA, &gpio_init_struct);
+    }
+#endif
+}
+#endif /* BSP_USING_ADC */
+
+#ifdef BSP_USING_HWTIMER
+void at32_msp_hwtmr_init(void *instance)
+{
+    tmr_type *tmr_x = (tmr_type *)instance;
+
+#ifdef BSP_USING_HWTMR3
+    if(tmr_x == TMR3)
+    {
+        /* tmr3 clock enable */
+        crm_periph_clock_enable(CRM_TMR3_PERIPH_CLOCK, TRUE);
+    }
+#endif
+}
+#endif

bsp/at32/at32f421-start/board/src/board.c

+/*
+ * Copyright (c) 2006-2021, RT-Thread Development Team
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Change Logs:
+ * Date           Author       Notes
+ * 2023-01-31     shelton      first version
+ */
+
+#include "board.h"
+
+void system_clock_config(void)
+{
+  /* config flash psr register */
+  flash_psr_set(FLASH_WAIT_CYCLE_3);
+
+  /* reset crm */
+  crm_reset();
+
+  crm_clock_source_enable(CRM_CLOCK_SOURCE_HEXT, TRUE);
+
+   /* wait till hext is ready */
+  while(crm_hext_stable_wait() == ERROR)
+  {
+  }
+
+  /* config pll clock resource */
+  crm_pll_config(CRM_PLL_SOURCE_HEXT, CRM_PLL_MULT_15);
+
+  /* enable pll */
+  crm_clock_source_enable(CRM_CLOCK_SOURCE_PLL, TRUE);
+
+  /* wait till pll is ready */
+  while(crm_flag_get(CRM_PLL_STABLE_FLAG) != SET)
+  {
+  }
+
+  /* config ahbclk */
+  crm_ahb_div_set(CRM_AHB_DIV_1);
+
+  /* config apb2clk, the maximum frequency of APB1/APB2 clock is 120 MHz  */
+  crm_apb2_div_set(CRM_APB2_DIV_1);
+
+  /* config apb1clk, the maximum frequency of APB1/APB2 clock is 120 MHz  */
+  crm_apb1_div_set(CRM_APB1_DIV_1);
+
+  /* enable auto step mode */
+  crm_auto_step_mode_enable(TRUE);
+
+  /* select pll as system clock source */
+  crm_sysclk_switch(CRM_SCLK_PLL);
+
+  /* wait till pll is used as system clock source */
+  while(crm_sysclk_switch_status_get() != CRM_SCLK_PLL)
+  {
+  }
+
+  /* disable auto step mode */
+  crm_auto_step_mode_enable(FALSE);
+
+  /* update system_core_clock global variable */
+  system_core_clock_update();
+}

bsp/at32/at32f421-start/project.eww

+<?xml version="1.0" encoding="iso-8859-1"?>
+
+<workspace>
+  <project>
+    <path>$WS_DIR$\project.ewp</path>
+  </project>
+  <batchBuild/>
+</workspace>
+
+

bsp/at32/at32f421-start/template.eww

+<?xml version="1.0" encoding="iso-8859-1"?>
+
+<workspace>
+  <project>
+    <path>$WS_DIR$\template.ewp</path>
+  </project>
+  <batchBuild/>
+</workspace>
+
+

bsp/at32/at32f425-start/project.eww

+<?xml version="1.0" encoding="iso-8859-1"?>
+
+<workspace>
+  <project>
+    <path>$WS_DIR$\project.ewp</path>
+  </project>
+  <batchBuild/>
+</workspace>
+
+