Kconfig

menu "Hardware Drivers Config"

config SOC_STM32F429BI
    bool
    select SOC_SERIES_STM32F4
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_RS232_TO_USART
        bool "Enable RS232 TO USART (uart1)"
        select BSP_USING_UART1
        default y

    config BSP_USING_EXT_FMC_IO
        bool "Enable extend gpio"
        default y

	config BSP_USING_SDRAM
        bool "Enable SDRAM"
        default n
		
	config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (w25q64 spi3)"
        select BSP_USING_SPI3
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_SDCARD
        bool "Enable SDCARD (sdio)"
        select BSP_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        default n

    config PHY_USING_DM9161CEP
        bool
    
    config BSP_USING_ETH
        bool "Enable Ethernet"
        default n
        select RT_USING_LWIP
        select PHY_USING_DM9161CEP

    config BSP_USING_MPU6050
        bool "Enable MPU6050(i2c1)"
        select BSP_USING_I2C1
        select PKG_USING_MPU6XXX
        select PKG_USING_MPU6XXX_SAMPLE
        select PKG_USING_MPU6XXX_LATEST_VERSION
        default n	

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    config BSP_USING_UART1
        bool "Enable UART1"
        select RT_USING_SERIAL
        default y

    config BSP_UART_USING_DMA_RX
        bool "Enable UART RX DMA support"
        default n

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

	config BSP_USING_SPI3
        bool "Enable SPI3 BUS"
        select RT_USING_SPI
        default n	
    
    config BSP_SPI_USING_DMA
        bool "Enable SPI DMA support"
        default n

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 1 216
                default 22
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 1 216
                default 25
        endif

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM11
                bool "Enable TIM11"
                default n

            config BSP_USING_TIM13
                bool "Enable TIM13"
                default n

            config BSP_USING_TIM14
                bool "Enable TIM14"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM2
            bool "Enable timer2 output pwm"
            default n
            if BSP_USING_PWM2
                config BSP_USING_PWM2_CH1
                    bool "Enable PWM2 channel1"
                    default n
            endif
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    config BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        select RT_USING_LIBC
        default n

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

endmenu

menu "Board extended module Drivers"

endmenu
 
endmenu