From d6a016616ba834b7da7653effb98d413acde7aa2 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Thu, 26 Jan 2012 02:11:06 +0800 Subject: [PATCH] atmel/nand: add DT support Use a local copy of board informatin and fill with DT data. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: Grant Likely Cc: Nicolas Ferre --- .../devicetree/bindings/mtd/atmel-nand.txt | 41 +++++++ arch/arm/boot/dts/at91sam9g20.dtsi | 16 +++ arch/arm/boot/dts/at91sam9g45.dtsi | 16 +++ arch/arm/boot/dts/at91sam9m10g45ek.dts | 25 +++- arch/arm/boot/dts/usb_a9g20.dts | 44 ++++++- arch/arm/mach-at91/at91sam9x5.c | 5 - arch/arm/mach-at91/board-dt.c | 51 -------- drivers/mtd/nand/atmel_nand.c | 113 ++++++++++++++---- 8 files changed, 233 insertions(+), 78 deletions(-) create mode 100644 Documentation/devicetree/bindings/mtd/atmel-nand.txt diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt new file mode 100644 index 000000000000..5903ecf6e895 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -0,0 +1,41 @@ +Atmel NAND flash + +Required properties: +- compatible : "atmel,at91rm9200-nand". +- reg : should specify localbus address and size used for the chip, + and if availlable the ECC. +- atmel,nand-addr-offset : offset for the address latch. +- atmel,nand-cmd-offset : offset for the command latch. +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. + +- gpios : specifies the gpio pins to control the NAND device. detect is an + optional gpio and may be set to 0 if not present. + +Optional properties: +- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", + "soft_bch". +- nand-bus-width : 8 or 16 bus width if not present 8 +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false + +Examples: +nand0: nand@40000000,0 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe800 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + nand-on-flash-bbt; + nand-ecc-mode = "soft"; + gpios = <&pioC 13 0 + &pioC 14 0 + 0 + >; + partition@0 { + ... + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g20.dtsi b/arch/arm/boot/dts/at91sam9g20.dtsi index a100db03ec90..4b0dc99b9319 100644 --- a/arch/arm/boot/dts/at91sam9g20.dtsi +++ b/arch/arm/boot/dts/at91sam9g20.dtsi @@ -172,5 +172,21 @@ macb0: ethernet@fffc4000 { status = "disabled"; }; }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe800 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + gpios = <&pioC 13 0 + &pioC 14 0 + 0 + >; + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index f779667159b1..d79021b831c4 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -180,5 +180,21 @@ macb0: ethernet@fffbc000 { status = "disabled"; }; }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe200 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + gpios = <&pioC 8 0 + &pioC 14 0 + 0 + >; + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts index 15e25f903cad..fd4531135431 100644 --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts @@ -14,7 +14,7 @@ / { compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9"; chosen { - bootargs = "mem=64M console=ttyS0,115200 mtdparts=atmel_nand:4M(bootstrap/uboot/kernel)ro,60M(rootfs),-(data) root=/dev/mtdblock1 rw rootfstype=jffs2"; + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2"; }; memory@70000000 { @@ -36,6 +36,29 @@ macb0: ethernet@fffbc000 { status = "okay"; }; }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + boot@0 { + label = "bootstrap/uboot/kernel"; + reg = <0x0 0x400000>; + }; + + rootfs@400000 { + label = "rootfs"; + reg = <0x400000 0x3C00000>; + }; + + data@4000000 { + label = "data"; + reg = <0x4000000 0xC000000>; + }; + + }; }; leds { diff --git a/arch/arm/boot/dts/usb_a9g20.dts b/arch/arm/boot/dts/usb_a9g20.dts index d74545a2a77c..71d83ef316df 100644 --- a/arch/arm/boot/dts/usb_a9g20.dts +++ b/arch/arm/boot/dts/usb_a9g20.dts @@ -13,7 +13,7 @@ / { compatible = "calao,usb-a9g20", "atmel,at91sam9g20", "atmel,at91sam9"; chosen { - bootargs = "mem=64M console=ttyS0,115200 mtdparts=atmel_nand:128k(at91bootstrap),256k(barebox)ro,128k(bareboxenv),128k(bareboxenv2),4M(kernel),120M(rootfs),-(data) root=/dev/mtdblock5 rw rootfstype=ubifs"; + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs"; }; memory@20000000 { @@ -31,6 +31,48 @@ macb0: ethernet@fffc4000 { status = "okay"; }; }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x20000>; + }; + + bareboxenv2@80000 { + label = "bareboxenv2"; + reg = <0x80000 0x20000>; + }; + + kernel@a0000 { + label = "kernel"; + reg = <0xa0000 0x400000>; + }; + + rootfs@4a0000 { + label = "rootfs"; + reg = <0x4a0000 0x7800000>; + }; + + data@7ca0000 { + label = "data"; + reg = <0x7ca0000 0x8360000>; + }; + }; }; leds { diff --git a/arch/arm/mach-at91/at91sam9x5.c b/arch/arm/mach-at91/at91sam9x5.c index a34d96afa746..7bec5a40d01a 100644 --- a/arch/arm/mach-at91/at91sam9x5.c +++ b/arch/arm/mach-at91/at91sam9x5.c @@ -313,11 +313,6 @@ void __init at91sam9x5_initialize(void) at91_gpio_init(NULL, 0); } -/* -------------------------------------------------------------------- - * AT91SAM9x5 devices (temporary before modification of code) - * -------------------------------------------------------------------- */ -void __init at91_add_device_nand(struct atmel_nand_data *data) {} - /* -------------------------------------------------------------------- * Interrupt initialization * -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91/board-dt.c b/arch/arm/mach-at91/board-dt.c index 2eb294b2cc0e..9f729d6c8942 100644 --- a/arch/arm/mach-at91/board-dt.c +++ b/arch/arm/mach-at91/board-dt.c @@ -19,10 +19,7 @@ #include #include -#include #include -#include -#include #include #include @@ -30,7 +27,6 @@ #include #include -#include "sam9_smc.h" #include "generic.h" @@ -40,50 +36,6 @@ static void __init ek_init_early(void) at91_initialize(12000000); } -/* det_pin is not connected */ -static struct atmel_nand_data __initdata ek_nand_data = { - .ale = 21, - .cle = 22, - .det_pin = -EINVAL, - .rdy_pin = AT91_PIN_PC8, - .enable_pin = AT91_PIN_PC14, - .ecc_mode = NAND_ECC_SOFT, - .on_flash_bbt = 1, -}; - -static struct sam9_smc_config __initdata ek_nand_smc_config = { - .ncs_read_setup = 0, - .nrd_setup = 2, - .ncs_write_setup = 0, - .nwe_setup = 2, - - .ncs_read_pulse = 4, - .nrd_pulse = 4, - .ncs_write_pulse = 4, - .nwe_pulse = 4, - - .read_cycle = 7, - .write_cycle = 7, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, - .tdf_cycles = 3, -}; - -static void __init ek_add_device_nand(void) -{ - ek_nand_data.bus_width_16 = board_have_nand_16bit(); - /* setup bus-width (8 or 16) */ - if (ek_nand_data.bus_width_16) - ek_nand_smc_config.mode |= AT91_SMC_DBW_16; - else - ek_nand_smc_config.mode |= AT91_SMC_DBW_8; - - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(0, 3, &ek_nand_smc_config); - - at91_add_device_nand(&ek_nand_data); -} - static const struct of_device_id irq_of_match[] __initconst = { { .compatible = "atmel,at91rm9200-aic", .data = at91_aic_of_init }, @@ -100,9 +52,6 @@ static void __init at91_dt_init_irq(void) static void __init at91_dt_device_init(void) { of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); - - /* NAND */ - ek_add_device_nand(); } static const char *at91_dt_board_compat[] __initdata = { diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index 045d174b8277..ae7e37d9ac17 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -27,6 +27,10 @@ #include #include #include +#include +#include +#include +#include #include #include #include @@ -83,7 +87,7 @@ struct atmel_nand_host { struct mtd_info mtd; void __iomem *io_base; dma_addr_t io_phys; - struct atmel_nand_data *board; + struct atmel_nand_data board; struct device *dev; void __iomem *ecc; @@ -101,8 +105,8 @@ static int cpu_has_dma(void) */ static void atmel_nand_enable(struct atmel_nand_host *host) { - if (gpio_is_valid(host->board->enable_pin)) - gpio_set_value(host->board->enable_pin, 0); + if (gpio_is_valid(host->board.enable_pin)) + gpio_set_value(host->board.enable_pin, 0); } /* @@ -110,8 +114,8 @@ static void atmel_nand_enable(struct atmel_nand_host *host) */ static void atmel_nand_disable(struct atmel_nand_host *host) { - if (gpio_is_valid(host->board->enable_pin)) - gpio_set_value(host->board->enable_pin, 1); + if (gpio_is_valid(host->board.enable_pin)) + gpio_set_value(host->board.enable_pin, 1); } /* @@ -132,9 +136,9 @@ static void atmel_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl return; if (ctrl & NAND_CLE) - writeb(cmd, host->io_base + (1 << host->board->cle)); + writeb(cmd, host->io_base + (1 << host->board.cle)); else - writeb(cmd, host->io_base + (1 << host->board->ale)); + writeb(cmd, host->io_base + (1 << host->board.ale)); } /* @@ -145,8 +149,8 @@ static int atmel_nand_device_ready(struct mtd_info *mtd) struct nand_chip *nand_chip = mtd->priv; struct atmel_nand_host *host = nand_chip->priv; - return gpio_get_value(host->board->rdy_pin) ^ - !!host->board->rdy_pin_active_low; + return gpio_get_value(host->board.rdy_pin) ^ + !!host->board.rdy_pin_active_low; } /* @@ -261,7 +265,7 @@ static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len) if (atmel_nand_dma_op(mtd, buf, len, 1) == 0) return; - if (host->board->bus_width_16) + if (host->board.bus_width_16) atmel_read_buf16(mtd, buf, len); else atmel_read_buf8(mtd, buf, len); @@ -277,7 +281,7 @@ static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len) if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) == 0) return; - if (host->board->bus_width_16) + if (host->board.bus_width_16) atmel_write_buf16(mtd, buf, len); else atmel_write_buf8(mtd, buf, len); @@ -469,6 +473,56 @@ static void atmel_nand_hwctl(struct mtd_info *mtd, int mode) } } +#if defined(CONFIG_OF) +static int __devinit atmel_of_init_port(struct atmel_nand_host *host, + struct device_node *np) +{ + u32 val; + int ecc_mode; + struct atmel_nand_data *board = &host->board; + enum of_gpio_flags flags; + + if (of_property_read_u32(np, "atmel,nand-addr-offset", &val) == 0) { + if (val >= 32) { + dev_err(host->dev, "invalid addr-offset %u\n", val); + return -EINVAL; + } + board->ale = val; + } + + if (of_property_read_u32(np, "atmel,nand-cmd-offset", &val) == 0) { + if (val >= 32) { + dev_err(host->dev, "invalid cmd-offset %u\n", val); + return -EINVAL; + } + board->cle = val; + } + + ecc_mode = of_get_nand_ecc_mode(np); + + board->ecc_mode = ecc_mode < 0 ? NAND_ECC_SOFT : ecc_mode; + + board->on_flash_bbt = of_get_nand_on_flash_bbt(np); + + if (of_get_nand_bus_width(np) == 16) + board->bus_width_16 = 1; + + board->rdy_pin = of_get_gpio_flags(np, 0, &flags); + board->rdy_pin_active_low = (flags == OF_GPIO_ACTIVE_LOW); + + board->enable_pin = of_get_gpio(np, 1); + board->det_pin = of_get_gpio(np, 2); + + return 0; +} +#else +static int __devinit atmel_of_init_port(struct atmel_nand_host *host, + struct device_node *np) +{ + return -EINVAL; +} +#endif + /* * Probe for the NAND device. */ @@ -479,6 +533,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev) struct nand_chip *nand_chip; struct resource *regs; struct resource *mem; + struct mtd_part_parser_data ppdata = {}; int res; mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -505,8 +560,15 @@ static int __init atmel_nand_probe(struct platform_device *pdev) mtd = &host->mtd; nand_chip = &host->nand_chip; - host->board = pdev->dev.platform_data; host->dev = &pdev->dev; + if (pdev->dev.of_node) { + res = atmel_of_init_port(host, pdev->dev.of_node); + if (res) + goto err_nand_ioremap; + } else { + memcpy(&host->board, pdev->dev.platform_data, + sizeof(struct atmel_nand_data)); + } nand_chip->priv = host; /* link the private data structures */ mtd->priv = nand_chip; @@ -517,10 +579,10 @@ static int __init atmel_nand_probe(struct platform_device *pdev) nand_chip->IO_ADDR_W = host->io_base; nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl; - if (gpio_is_valid(host->board->rdy_pin)) + if (gpio_is_valid(host->board.rdy_pin)) nand_chip->dev_ready = atmel_nand_device_ready; - nand_chip->ecc.mode = host->board->ecc_mode; + nand_chip->ecc.mode = host->board.ecc_mode; regs = platform_get_resource(pdev, IORESOURCE_MEM, 1); if (!regs && nand_chip->ecc.mode == NAND_ECC_HW) { @@ -545,7 +607,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev) nand_chip->chip_delay = 20; /* 20us command delay time */ - if (host->board->bus_width_16) /* 16-bit bus width */ + if (host->board.bus_width_16) /* 16-bit bus width */ nand_chip->options |= NAND_BUSWIDTH_16; nand_chip->read_buf = atmel_read_buf; @@ -554,15 +616,15 @@ static int __init atmel_nand_probe(struct platform_device *pdev) platform_set_drvdata(pdev, host); atmel_nand_enable(host); - if (gpio_is_valid(host->board->det_pin)) { - if (gpio_get_value(host->board->det_pin)) { + if (gpio_is_valid(host->board.det_pin)) { + if (gpio_get_value(host->board.det_pin)) { printk(KERN_INFO "No SmartMedia card inserted.\n"); res = -ENXIO; goto err_no_card; } } - if (host->board->on_flash_bbt || on_flash_bbt) { + if (host->board.on_flash_bbt || on_flash_bbt) { printk(KERN_INFO "atmel_nand: Use On Flash BBT\n"); nand_chip->bbt_options |= NAND_BBT_USE_FLASH; } @@ -637,8 +699,9 @@ static int __init atmel_nand_probe(struct platform_device *pdev) } mtd->name = "atmel_nand"; - res = mtd_device_parse_register(mtd, NULL, 0, - host->board->parts, host->board->num_parts); + ppdata.of_node = pdev->dev.of_node; + res = mtd_device_parse_register(mtd, NULL, &ppdata, + host->board.parts, host->board.num_parts); if (!res) return res; @@ -682,11 +745,21 @@ static int __exit atmel_nand_remove(struct platform_device *pdev) return 0; } +#if defined(CONFIG_OF) +static const struct of_device_id atmel_nand_dt_ids[] = { + { .compatible = "atmel,at91rm9200-nand" }, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(of, atmel_nand_dt_ids); +#endif + static struct platform_driver atmel_nand_driver = { .remove = __exit_p(atmel_nand_remove), .driver = { .name = "atmel_nand", .owner = THIS_MODULE, + .of_match_table = of_match_ptr(atmel_nand_dt_ids), }, }; -- GitLab