diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c index 2a229a1d3211e181a055855813bdf0c75079bd90..40645ed125b192d23cf2d01d5b41a1d0322f251c 100644 --- a/drivers/ata/libata-sff.c +++ b/drivers/ata/libata-sff.c @@ -38,6 +38,43 @@ #include "libata.h" +/** + * ata_check_status - Read device status reg & clear interrupt + * @ap: port where the device is + * + * Reads ATA taskfile status register for currently-selected device + * and return its value. This also clears pending interrupts + * from this device + * + * LOCKING: + * Inherited from caller. + */ +u8 ata_check_status(struct ata_port *ap) +{ + return ioread8(ap->ioaddr.status_addr); +} + +/** + * ata_altstatus - Read device alternate status reg + * @ap: port where the device is + * + * Reads ATA taskfile alternate status register for + * currently-selected device and return its value. + * + * Note: may NOT be used as the check_altstatus() entry in + * ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ +u8 ata_altstatus(struct ata_port *ap) +{ + if (ap->ops->check_altstatus) + return ap->ops->check_altstatus(ap); + + return ioread8(ap->ioaddr.altstatus_addr); +} + /** * ata_irq_on - Enable interrupts on a port. * @ap: Port on which interrupts are enabled. @@ -65,6 +102,27 @@ u8 ata_irq_on(struct ata_port *ap) return tmp; } +/** + * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt. + * @ap: Port associated with this ATA transaction. + * + * Clear interrupt and error flags in DMA status register. + * + * May be used as the irq_clear() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_bmdma_irq_clear(struct ata_port *ap) +{ + void __iomem *mmio = ap->ioaddr.bmdma_addr; + + if (!mmio) + return; + + iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS); +} + /** * ata_tf_load - send taskfile registers to host controller * @ap: Port to which output is sent @@ -75,7 +133,6 @@ u8 ata_irq_on(struct ata_port *ap) * LOCKING: * Inherited from caller. */ - void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) { struct ata_ioports *ioaddr = &ap->ioaddr; @@ -125,25 +182,6 @@ void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) ata_wait_idle(ap); } -/** - * ata_exec_command - issue ATA command to host controller - * @ap: port to which command is being issued - * @tf: ATA taskfile register set - * - * Issues ATA command, with proper synchronization with interrupt - * handler / other threads. - * - * LOCKING: - * spin_lock_irqsave(host lock) - */ -void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf) -{ - DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command); - - iowrite8(tf->command, ap->ioaddr.command_addr); - ata_pause(ap); -} - /** * ata_tf_read - input device's ATA taskfile shadow registers * @ap: Port from which input is read @@ -185,169 +223,22 @@ void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf) } /** - * ata_check_status - Read device status reg & clear interrupt - * @ap: port where the device is - * - * Reads ATA taskfile status register for currently-selected device - * and return its value. This also clears pending interrupts - * from this device - * - * LOCKING: - * Inherited from caller. - */ -u8 ata_check_status(struct ata_port *ap) -{ - return ioread8(ap->ioaddr.status_addr); -} - -/** - * ata_altstatus - Read device alternate status reg - * @ap: port where the device is - * - * Reads ATA taskfile alternate status register for - * currently-selected device and return its value. - * - * Note: may NOT be used as the check_altstatus() entry in - * ata_port_operations. - * - * LOCKING: - * Inherited from caller. - */ -u8 ata_altstatus(struct ata_port *ap) -{ - if (ap->ops->check_altstatus) - return ap->ops->check_altstatus(ap); - - return ioread8(ap->ioaddr.altstatus_addr); -} - -/** - * ata_bmdma_setup - Set up PCI IDE BMDMA transaction - * @qc: Info associated with this ATA transaction. - * - * LOCKING: - * spin_lock_irqsave(host lock) - */ -void ata_bmdma_setup(struct ata_queued_cmd *qc) -{ - struct ata_port *ap = qc->ap; - unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); - u8 dmactl; - - /* load PRD table addr. */ - mb(); /* make sure PRD table writes are visible to controller */ - iowrite32(ap->prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS); - - /* specify data direction, triple-check start bit is clear */ - dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); - dmactl &= ~(ATA_DMA_WR | ATA_DMA_START); - if (!rw) - dmactl |= ATA_DMA_WR; - iowrite8(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD); - - /* issue r/w command */ - ap->ops->exec_command(ap, &qc->tf); -} - -/** - * ata_bmdma_start - Start a PCI IDE BMDMA transaction - * @qc: Info associated with this ATA transaction. - * - * LOCKING: - * spin_lock_irqsave(host lock) - */ -void ata_bmdma_start(struct ata_queued_cmd *qc) -{ - struct ata_port *ap = qc->ap; - u8 dmactl; - - /* start host DMA transaction */ - dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); - iowrite8(dmactl | ATA_DMA_START, ap->ioaddr.bmdma_addr + ATA_DMA_CMD); - - /* Strictly, one may wish to issue an ioread8() here, to - * flush the mmio write. However, control also passes - * to the hardware at this point, and it will interrupt - * us when we are to resume control. So, in effect, - * we don't care when the mmio write flushes. - * Further, a read of the DMA status register _immediately_ - * following the write may not be what certain flaky hardware - * is expected, so I think it is best to not add a readb() - * without first all the MMIO ATA cards/mobos. - * Or maybe I'm just being paranoid. - * - * FIXME: The posting of this write means I/O starts are - * unneccessarily delayed for MMIO - */ -} - -/** - * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt. - * @ap: Port associated with this ATA transaction. - * - * Clear interrupt and error flags in DMA status register. - * - * May be used as the irq_clear() entry in ata_port_operations. - * - * LOCKING: - * spin_lock_irqsave(host lock) - */ -void ata_bmdma_irq_clear(struct ata_port *ap) -{ - void __iomem *mmio = ap->ioaddr.bmdma_addr; - - if (!mmio) - return; - - iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS); -} - -/** - * ata_noop_irq_clear - Noop placeholder for irq_clear - * @ap: Port associated with this ATA transaction. - */ -void ata_noop_irq_clear(struct ata_port *ap) -{ -} - -/** - * ata_bmdma_status - Read PCI IDE BMDMA status - * @ap: Port associated with this ATA transaction. - * - * Read and return BMDMA status register. - * - * May be used as the bmdma_status() entry in ata_port_operations. - * - * LOCKING: - * spin_lock_irqsave(host lock) - */ -u8 ata_bmdma_status(struct ata_port *ap) -{ - return ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); -} - -/** - * ata_bmdma_stop - Stop PCI IDE BMDMA transfer - * @qc: Command we are ending DMA for - * - * Clears the ATA_DMA_START flag in the dma control register + * ata_exec_command - issue ATA command to host controller + * @ap: port to which command is being issued + * @tf: ATA taskfile register set * - * May be used as the bmdma_stop() entry in ata_port_operations. + * Issues ATA command, with proper synchronization with interrupt + * handler / other threads. * * LOCKING: * spin_lock_irqsave(host lock) */ -void ata_bmdma_stop(struct ata_queued_cmd *qc) +void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf) { - struct ata_port *ap = qc->ap; - void __iomem *mmio = ap->ioaddr.bmdma_addr; - - /* clear start/stop bit */ - iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ATA_DMA_START, - mmio + ATA_DMA_CMD); + DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command); - /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */ - ata_altstatus(ap); /* dummy read */ + iowrite8(tf->command, ap->ioaddr.command_addr); + ata_pause(ap); } /** @@ -495,7 +386,6 @@ void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc) * LOCKING: * Inherited from caller. */ - int ata_sff_port_start(struct ata_port *ap) { if (ap->ioaddr.bmdma_addr) @@ -503,20 +393,149 @@ int ata_sff_port_start(struct ata_port *ap) return 0; } +/** + * ata_bmdma_setup - Set up PCI IDE BMDMA transaction + * @qc: Info associated with this ATA transaction. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_bmdma_setup(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); + u8 dmactl; + + /* load PRD table addr. */ + mb(); /* make sure PRD table writes are visible to controller */ + iowrite32(ap->prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS); + + /* specify data direction, triple-check start bit is clear */ + dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + dmactl &= ~(ATA_DMA_WR | ATA_DMA_START); + if (!rw) + dmactl |= ATA_DMA_WR; + iowrite8(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + + /* issue r/w command */ + ap->ops->exec_command(ap, &qc->tf); +} + +/** + * ata_bmdma_start - Start a PCI IDE BMDMA transaction + * @qc: Info associated with this ATA transaction. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + u8 dmactl; + + /* start host DMA transaction */ + dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + iowrite8(dmactl | ATA_DMA_START, ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + + /* Strictly, one may wish to issue an ioread8() here, to + * flush the mmio write. However, control also passes + * to the hardware at this point, and it will interrupt + * us when we are to resume control. So, in effect, + * we don't care when the mmio write flushes. + * Further, a read of the DMA status register _immediately_ + * following the write may not be what certain flaky hardware + * is expected, so I think it is best to not add a readb() + * without first all the MMIO ATA cards/mobos. + * Or maybe I'm just being paranoid. + * + * FIXME: The posting of this write means I/O starts are + * unneccessarily delayed for MMIO + */ +} + +/** + * ata_bmdma_stop - Stop PCI IDE BMDMA transfer + * @qc: Command we are ending DMA for + * + * Clears the ATA_DMA_START flag in the dma control register + * + * May be used as the bmdma_stop() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *mmio = ap->ioaddr.bmdma_addr; + + /* clear start/stop bit */ + iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ATA_DMA_START, + mmio + ATA_DMA_CMD); + + /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */ + ata_altstatus(ap); /* dummy read */ +} + +/** + * ata_bmdma_status - Read PCI IDE BMDMA status + * @ap: Port associated with this ATA transaction. + * + * Read and return BMDMA status register. + * + * May be used as the bmdma_status() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +u8 ata_bmdma_status(struct ata_port *ap) +{ + return ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); +} + +/** + * ata_noop_irq_clear - Noop placeholder for irq_clear + * @ap: Port associated with this ATA transaction. + */ +void ata_noop_irq_clear(struct ata_port *ap) +{ +} + #ifdef CONFIG_PCI -static int ata_resources_present(struct pci_dev *pdev, int port) +/** + * ata_pci_clear_simplex - attempt to kick device out of simplex + * @pdev: PCI device + * + * Some PCI ATA devices report simplex mode but in fact can be told to + * enter non simplex mode. This implements the necessary logic to + * perform the task on such devices. Calling it on other devices will + * have -undefined- behaviour. + */ +int ata_pci_clear_simplex(struct pci_dev *pdev) { - int i; + unsigned long bmdma = pci_resource_start(pdev, 4); + u8 simplex; - /* Check the PCI resources for this channel are enabled */ - port = port * 2; - for (i = 0; i < 2; i ++) { - if (pci_resource_start(pdev, port + i) == 0 || - pci_resource_len(pdev, port + i) == 0) - return 0; - } - return 1; + if (bmdma == 0) + return -ENOENT; + + simplex = inb(bmdma + 0x02); + outb(simplex & 0x60, bmdma + 0x02); + simplex = inb(bmdma + 0x02); + if (simplex & 0x80) + return -EOPNOTSUPP; + return 0; +} + +unsigned long ata_pci_default_filter(struct ata_device *adev, unsigned long xfer_mask) +{ + /* Filter out DMA modes if the device has been configured by + the BIOS as PIO only */ + + if (adev->link->ap->ioaddr.bmdma_addr == NULL) + xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA); + return xfer_mask; } /** @@ -576,6 +595,20 @@ int ata_pci_init_bmdma(struct ata_host *host) return 0; } +static int ata_resources_present(struct pci_dev *pdev, int port) +{ + int i; + + /* Check the PCI resources for this channel are enabled */ + port = port * 2; + for (i = 0; i < 2; i ++) { + if (pci_resource_start(pdev, port + i) == 0 || + pci_resource_len(pdev, port + i) == 0) + return 0; + } + return 1; +} + /** * ata_pci_init_sff_host - acquire native PCI ATA resources and init host * @host: target ATA host @@ -879,41 +912,5 @@ int ata_pci_init_one(struct pci_dev *pdev, return rc; } -/** - * ata_pci_clear_simplex - attempt to kick device out of simplex - * @pdev: PCI device - * - * Some PCI ATA devices report simplex mode but in fact can be told to - * enter non simplex mode. This implements the necessary logic to - * perform the task on such devices. Calling it on other devices will - * have -undefined- behaviour. - */ - -int ata_pci_clear_simplex(struct pci_dev *pdev) -{ - unsigned long bmdma = pci_resource_start(pdev, 4); - u8 simplex; - - if (bmdma == 0) - return -ENOENT; - - simplex = inb(bmdma + 0x02); - outb(simplex & 0x60, bmdma + 0x02); - simplex = inb(bmdma + 0x02); - if (simplex & 0x80) - return -EOPNOTSUPP; - return 0; -} - -unsigned long ata_pci_default_filter(struct ata_device *adev, unsigned long xfer_mask) -{ - /* Filter out DMA modes if the device has been configured by - the BIOS as PIO only */ - - if (adev->link->ap->ioaddr.bmdma_addr == NULL) - xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA); - return xfer_mask; -} - #endif /* CONFIG_PCI */