add raspi3-64 i2c driver

bsp/raspberry-pi/raspi3-64/.config

@@ -148,7 +148,10 @@ CONFIG_RT_SERIAL_RB_BUFSZ=64
 # CONFIG_RT_USING_CAN is not set
 CONFIG_RT_USING_HWTIMER=y
 # CONFIG_RT_USING_CPUTIME is not set
-# CONFIG_RT_USING_I2C is not set
+CONFIG_RT_USING_I2C=y
+CONFIG_RT_I2C_DEBUG=y
+CONFIG_RT_USING_I2C_BITOPS=y
+# CONFIG_RT_I2C_BITOPS_DEBUG is not set
 CONFIG_RT_USING_PIN=y
 # CONFIG_RT_USING_ADC is not set
 # CONFIG_RT_USING_PWM is not set
@@ -420,36 +423,6 @@ CONFIG_RT_USING_POSIX=y
 # CONFIG_PKG_USING_VT100 is not set
 # CONFIG_PKG_USING_ULAPACK is not set
 # CONFIG_PKG_USING_UKAL is not set
-
-#
-# Privated Packages of RealThread
-#
-# CONFIG_PKG_USING_CODEC is not set
-# CONFIG_PKG_USING_PLAYER is not set
-# CONFIG_PKG_USING_MPLAYER is not set
-# CONFIG_PKG_USING_PERSIMMON_SRC is not set
-# CONFIG_PKG_USING_JS_PERSIMMON is not set
-# CONFIG_PKG_USING_JERRYSCRIPT_WIN32 is not set
-
-#
-# Network Utilities
-#
-# CONFIG_PKG_USING_WICED is not set
-# CONFIG_PKG_USING_CLOUDSDK is not set
-# CONFIG_PKG_USING_POWER_MANAGER is not set
-# CONFIG_PKG_USING_RT_OTA is not set
-# CONFIG_PKG_USING_RDBD_SRC is not set
-# CONFIG_PKG_USING_RTINSIGHT is not set
-# CONFIG_PKG_USING_SMARTCONFIG is not set
-# CONFIG_PKG_USING_RTX is not set
-# CONFIG_RT_USING_TESTCASE is not set
-# CONFIG_PKG_USING_NGHTTP2 is not set
-# CONFIG_PKG_USING_AVS is not set
-# CONFIG_PKG_USING_JOYLINK is not set
-# CONFIG_PKG_USING_STS is not set
-# CONFIG_PKG_USING_DLMS is not set
-# CONFIG_PKG_USING_AUDIO_FRAMEWORK is not set
-# CONFIG_PKG_USING_ZBAR is not set
 CONFIG_BCM2836_SOC=y
 # CONFIG_BSP_SUPPORT_FPU is not set
 
@@ -468,7 +441,9 @@ CONFIG_BSP_USING_CORETIMER=y
 CONFIG_BSP_USING_SYSTIMER=y
 CONFIG_RT_USING_SYSTIMER1=y
 CONFIG_RT_USING_SYSTIMER3=y
-# CONFIG_BSP_USING_I2C is not set
+CONFIG_BSP_USING_I2C=y
+# CONFIG_BSP_USING_I2C0 is not set
+CONFIG_BSP_USING_I2C1=y
 # CONFIG_BSP_USING_SPI is not set
 CONFIG_BSP_USING_WDT=y
 # CONFIG_BSP_USING_RTC is not set

bsp/raspberry-pi/raspi3-64/driver/board.c

@@ -100,6 +100,8 @@ void rt_hw_board_init(void)
     armv8_map(0x40000000, 0x40000000, 0x1000, MEM_ATTR_IO);//core timer
     armv8_map(0x3F300000, 0x3F300000, 0x1000, MEM_ATTR_IO);//sdio
     armv8_map(0xc00000, 0xc00000, 0x1000, MEM_ATTR_IO);//mbox
+    armv8_map(0x3f804000, 0x3f804000, 0x1000, MEM_ATTR_IO);//i2c0
+    armv8_map(0x3f205000, 0x3f205000, 0x1000, MEM_ATTR_IO);//i2c1
     mmu_enable();
     
     /* initialize hardware interrupt */

bsp/raspberry-pi/raspi3-64/driver/drv_i2c.c

 /*
- * Copyright (c) 2006-2019, RT-Thread Development Team
+ * Copyright (c) 2006-2020, RT-Thread Development Team
  *
  * SPDX-License-Identifier: Apache-2.0
  *
@@ -8,55 +8,103 @@
  * 2019-07-29     zdzn           first version
  */
 
+#include "raspi.h"
 #include "drv_i2c.h"
 
-#if defined (BSP_USING_I2C0)
-#define I2C1BUS_NAME  "i2c0"
-#endif /*BSP_USING_I2C0*/
-
-#if defined (BSP_USING_I2C1)
-#define I2C2BUS_NAME  "i2c1"
-#endif /*BSP_USING_I2C1*/
-
-static int i2c_byte_wait_us = 0;
-
-#ifdef BSP_USING_I2C0
+//Maybe redefined
+typedef unsigned long                   rt_ubase_t;
+typedef rt_ubase_t                      rt_size_t;
 
-static struct raspi_i2c_bus raspi_i2c0 =
+rt_uint8_t i2c_read_or_write(volatile rt_uint32_t base, rt_uint8_t* buf, rt_uint32_t len, rt_uint8_t flag)
 {
-    .device_name = I2C1BUS_NAME,
-};
+    rt_uint32_t status;
+    rt_uint32_t remaining = len;
+    rt_uint32_t i = 0;
+    rt_uint8_t reason = BCM283X_I2C_REASON_OK;
+
+    /* Clear FIFO */
+    BCM283X_BSC_C(base) |= (BSC_C_CLEAR_1 & BSC_C_CLEAR_1);
+    /* Clear Status */
+    BCM283X_BSC_S(base) = BSC_S_CLKT | BSC_S_ERR | BSC_S_DONE;
+    /* Set Data Length */
+    BCM283X_BSC_DLEN(base) = len;
+    if (flag)
+    {
+        /* Start read */
+        BCM283X_BSC_C(base) = BSC_C_I2CEN | BSC_C_ST | BSC_C_READ;
+        /* wait for transfer to complete */
+        while (!(BCM283X_BSC_S(base) & BSC_S_DONE))
+        {
+            /* we must empty the FIFO as it is populated and not use any delay */
+            while (remaining && (BCM283X_BSC_S(base) & BSC_S_RXD))
+            {
+                /* Read from FIFO, no barrier */
+                buf[i] = BCM283X_BSC_FIFO(base);
+                i++;
+                remaining--;
+            }
+        }
+        /* transfer has finished - grab any remaining stuff in FIFO */
+        while (remaining && (BCM283X_BSC_S(base) & BSC_S_RXD))
+        {
+            /* Read from FIFO, no barrier */
+            buf[i] = BCM283X_BSC_FIFO(base);
+            i++;
+            remaining--;
+        }
+    }
+    else
+    {
+        /* pre populate FIFO with max buffer */
+        while (remaining && (i < BSC_FIFO_SIZE))
+        {
+            BCM283X_BSC_FIFO(base) = buf[i];
+            i++;
+            remaining--;
+        }
 
-static struct raspi_master_config_t raspi_i2c0_cfg =
-{
-    .sdl_pin = BCM_GPIO_PIN_0,
-    .scl_pin = BCM_GPIO_PIN_1,
-    .sdl_pin_mode = BCM283X_GPIO_FSEL_ALT0,
-    .scl_pin_mode = BCM283X_GPIO_FSEL_ALT0,
-    .slave_address = 8,
-    .bsc_base = (PER_BASE + BCM283X_BSC0_BASE),
-    .clk_div = BCM283X_I2C_CLOCK_DIVIDER_148,
-};
+        /* Enable device and start transfer */
+        BCM283X_BSC_C(base) = BSC_C_I2CEN | BSC_C_ST;
 
-#endif /* RT_USING_HW_I2C1 */
+        /* Transfer is over when BCM2835_BSC_S_DONE */
+        while (!(BCM283X_BSC_S(base) & BSC_S_DONE))
+        {
+            while (remaining && (BCM283X_BSC_S(base) & BSC_S_TXD))
+            {
+                /* Write to FIFO */
+                BCM283X_BSC_FIFO(base) = buf[i];
+                i++;
+                remaining--;
+            }
+        }
+    }
 
-#ifdef BSP_USING_I2C1
-static struct raspi_i2c_bus raspi_i2c1 =
-{
-    .device_name = I2C2BUS_NAME,
-};
+    status = BCM283X_BSC_S(base);
+    if (status & BSC_S_ERR)
+    {
+        reason = BCM283X_I2C_REASON_ERROR_NACK;
+    }
+    else if (status & BSC_S_CLKT)
+    {
+        reason = BCM283X_I2C_REASON_ERROR_CLKT;
+    }
+    else if (remaining)
+    {
+        reason = BCM283X_I2C_REASON_ERROR_DATA;
+    }
+    BCM283X_BSC_C(base) |= (BSC_S_DONE & BSC_S_DONE);
 
-static struct raspi_master_config_t raspi_i2c1_cfg =
+    return reason;
+}
+
+struct raspi_i2c_hw_config
 {
-    .sdl_pin = BCM_GPIO_PIN_2,
-    .scl_pin = BCM_GPIO_PIN_3,
-    .sdl_pin_mode = BCM283X_GPIO_FSEL_ALT0,
-    .scl_pin_mode = BCM283X_GPIO_FSEL_ALT0,
-    .slave_address = 9,
-    .bsc_base = (PER_BASE + BCM283X_BSC1_BASE),
-    .clk_div = BCM283X_I2C_CLOCK_DIVIDER_148,
+    rt_uint8_t bsc_num;
+    rt_uint8_t sdl_pin;
+    rt_uint8_t scl_pin;
+    rt_uint8_t sdl_mode;
+    rt_uint8_t scl_mode;
 };
-#endif /* RT_USING_HW_I2C2 */
 
 #if (defined(BSP_USING_I2C0) || defined(BSP_USING_I2C1))
 
@@ -70,58 +118,32 @@ static rt_err_t raspi_i2c_bus_control(struct rt_i2c_bus_device *bus,
                                       rt_uint32_t,
                                       rt_uint32_t);
 
-void i2c_master_init(struct raspi_master_config_t *cfg)
-{
-    volatile rt_uint32_t addr;
-    rt_uint32_t data;
-
-    bcm283x_gpio_fsel(cfg->sdl_pin, cfg->sdl_pin_mode); /* SDA */
-    bcm283x_gpio_fsel(cfg->scl_pin, cfg->scl_pin_mode); /* SCL */
-
-    addr = cfg->bsc_base + BCM283X_BSC_DIV;
-    data = bcm283x_peri_read(addr);
-    i2c_byte_wait_us = ( data * 1000000 / BCM283X_CORE_CLK_HZ) * 9;
-
-    addr = cfg->bsc_base + BCM283X_BSC_DIV;
-    bcm283x_peri_write(addr, cfg->clk_div);
-
-    //update
-    i2c_byte_wait_us = (cfg->clk_div * 1000000 * 9 / BCM283X_CORE_CLK_HZ);
-}
-
+static rt_uint32_t i2c_byte_wait_us = 0;
 static rt_size_t raspi_i2c_mst_xfer(struct rt_i2c_bus_device *bus,
                                     struct rt_i2c_msg msgs[],
                                     rt_uint32_t num)
 {
-    volatile rt_uint32_t addr;
-    struct raspi_i2c_bus *raspi_i2c;
     rt_size_t i;
+    rt_uint8_t reason;
     RT_ASSERT(bus != RT_NULL);
-    raspi_i2c = (struct raspi_i2c_bus *) bus;
-    raspi_i2c->msg = msgs;
-    raspi_i2c->msg_ptr = 0;
-    raspi_i2c->msg_cnt = num;
-    raspi_i2c->dptr = 0;
 
-    addr = raspi_i2c->cfg->bsc_base + BCM283X_BSC_A;
-    bcm283x_peri_write(addr, msgs->addr);
+    volatile rt_base_t base = (volatile rt_base_t)(bus->parent.user_data);
+
+    if (bus->addr == 0)
+        base = BCM283X_BSC0_BASE; 
+    else
+        base = BCM283X_BSC1_BASE;
+
+    BCM283X_BSC_A(base) = msgs->addr;
 
     for (i = 0; i < num; i++)
     {
-        if ( raspi_i2c->msg[i].flags & RT_I2C_RD )
-        {
-            bcm283x_i2c_read(raspi_i2c->cfg->bsc_base, raspi_i2c->msg->buf, num);
-        }
+        if (msgs[i].flags & RT_I2C_RD)
+            reason = i2c_read_or_write(base, msgs->buf, msgs->len, 1);
         else
-        {
-            bcm283x_i2c_write(raspi_i2c->cfg->bsc_base, raspi_i2c->msg->buf, num);
+            reason = i2c_read_or_write(base, msgs->buf, msgs->len, 0);
     }
-    }
-    raspi_i2c->msg = RT_NULL;
-    raspi_i2c->msg_ptr = 0;
-    raspi_i2c->msg_cnt = 0;
-    raspi_i2c->dptr = 0;
-    return i;
+    return (reason == 0)? i : 0;
 }
 
 static rt_size_t raspi_i2c_slv_xfer(struct rt_i2c_bus_device *bus,
@@ -134,7 +156,7 @@ static rt_err_t raspi_i2c_bus_control(struct rt_i2c_bus_device *bus,
                                       rt_uint32_t cmd,
                                       rt_uint32_t arg)
 {
-    return RT_ERROR;
+    return RT_EOK;
 }
 
 static const struct rt_i2c_bus_device_ops raspi_i2c_ops =
@@ -144,33 +166,72 @@ static const struct rt_i2c_bus_device_ops raspi_i2c_ops =
     .i2c_bus_control = raspi_i2c_bus_control,
 };
 
-static rt_err_t raspi_i2c_configure(struct raspi_i2c_bus *bus, struct raspi_master_config_t *cfg)
+
+static rt_err_t raspi_i2c_configure(struct raspi_i2c_hw_config *cfg)
 {
-    RT_ASSERT(bus != RT_NULL);
     RT_ASSERT(cfg != RT_NULL);
 
-    bus->device.ops = &raspi_i2c_ops;
-    bus->cfg = cfg;
+    volatile rt_uint32_t base = cfg->scl_mode ? BCM283X_BSC1_BASE : BCM283X_BSC0_BASE;
+
+    GPIO_FSEL(cfg->sdl_pin, cfg->sdl_mode); /* SDA */
+    GPIO_FSEL(cfg->scl_pin, cfg->scl_mode); /* SCL */
+    /* use 0xFFFE mask to limit a max value and round down any odd number */
+    rt_uint32_t divider = (BCM283X_CORE_CLK_HZ / 10000) & 0xFFFE;
+    BCM283X_BSC_DIV(base) = (rt_uint16_t) divider;
+    i2c_byte_wait_us = (divider * 1000000 * 9 / BCM283X_CORE_CLK_HZ);
 
-    i2c_master_init(cfg);
     return RT_EOK;
 }
 #endif
 
-int rt_hw_i2c_init(void)
+#if defined (BSP_USING_I2C0)
+#define I2C0_BUS_NAME    "i2c0"
+static struct raspi_i2c_hw_config hw_device0 =
 {
+    .bsc_num = 0,
+    .sdl_pin = RPI_GPIO_P1_27,
+    .scl_pin = RPI_GPIO_P1_28,
+    .sdl_mode = BCM283X_GPIO_FSEL_ALT0,
+    .scl_mode = BCM283X_GPIO_FSEL_ALT0,
+};
 
-#if defined(BSP_USING_I2C0)
-    raspi_i2c_configure(&raspi_i2c0 , &raspi_i2c0_cfg);
-    rt_i2c_bus_device_register(&raspi_i2c0.device, raspi_i2c0.device_name);
-#endif  /* BSP_USING_I2C1 */
+struct rt_i2c_bus_device device0 =
+{
+    .ops = &raspi_i2c_ops,
+    .addr = 0,
+};
 
-#if defined(BSP_USING_I2C1)
+#endif
+
+#if defined (BSP_USING_I2C1)
+#define I2C1_BUS_NAME    "i2c1"
+static struct raspi_i2c_hw_config hw_device1 =
+{
+    .bsc_num = 1,
+    .sdl_pin = RPI_GPIO_P1_03,
+    .scl_pin = RPI_GPIO_P1_05,
+    .sdl_mode = BCM283X_GPIO_FSEL_ALT0,
+    .scl_mode = BCM283X_GPIO_FSEL_ALT0,
+};
+struct rt_i2c_bus_device device1 =
+{
+    .ops = &raspi_i2c_ops,
+    .addr = 1,
+};
 
-    raspi_i2c_configure(&raspi_i2c1 , &raspi_i2c1_cfg);
-    rt_i2c_bus_device_register(&raspi_i2c1.device, raspi_i2c1.device_name);
+#endif
 
-#endif  /* BSP_USING_I2C2 */
+int rt_hw_i2c_init(void)
+{
+#if defined(BSP_USING_I2C0)
+    raspi_i2c_configure(&hw_device0);
+    rt_i2c_bus_device_register(&device0, I2C0_BUS_NAME);
+#endif
+
+#if defined(BSP_USING_I2C1)
+    raspi_i2c_configure(&hw_device1);
+    rt_i2c_bus_device_register(&device1, I2C1_BUS_NAME);
+#endif
 
     return 0;
 }

bsp/raspberry-pi/raspi3-64/driver/drv_i2c.h

 /*
- * Copyright (c) 2006-2019, RT-Thread Development Team
+ * Copyright (c) 2006-2020, RT-Thread Development Team
  *
  * SPDX-License-Identifier: Apache-2.0
  *
@@ -11,10 +11,10 @@
 #ifndef __DRV_I2C_H__
 #define __DRV_I2C_H__
 
-#include <rthw.h>
 #include <rtdevice.h>
 #include <rtthread.h>
-#include "bcm283x.h"
+
+#include "board.h"
 
 struct raspi_master_config_t
 {

bsp/raspberry-pi/raspi3-64/rtconfig.h

@@ -102,6 +102,9 @@
 #define RT_USING_SERIAL
 #define RT_SERIAL_RB_BUFSZ 64
 #define RT_USING_HWTIMER
+#define RT_USING_I2C
+#define RT_I2C_DEBUG
+#define RT_USING_I2C_BITOPS
 #define RT_USING_PIN
 #define RT_USING_SDIO
 #define RT_SDIO_STACK_SIZE 2048
@@ -179,12 +182,6 @@
 
 /* samples: kernel and components samples */
 
-
-/* Privated Packages of RealThread */
-
-
-/* Network Utilities */
-
 #define BCM2836_SOC
 
 /* Hardware Drivers Config */
@@ -198,6 +195,8 @@
 #define BSP_USING_SYSTIMER
 #define RT_USING_SYSTIMER1
 #define RT_USING_SYSTIMER3
+#define BSP_USING_I2C
+#define BSP_USING_I2C1
 #define BSP_USING_WDT
 #define BSP_USING_SDIO
 #define BSP_USING_SDIO0