/***************************************************************************** * Copyright (c) 2019, Nations Technologies Inc. * * All rights reserved. * **************************************************************************** * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * - Redistributions of source code must retain the above copyright notice, * this list of conditions and the disclaimer below. * * Nations' name may not be used to endorse or promote products derived from * this software without specific prior written permission. * * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY NATIONS "AS IS" AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE * DISCLAIMED. IN NO EVENT SHALL NATIONS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ /** * @file n32g45x_tim.c * @author Nations * @version v1.0.2 * * @copyright Copyright (c) 2019, Nations Technologies Inc. All rights reserved. */ #include "n32g45x_tim.h" #include "n32g45x_rcc.h" /** @addtogroup N32G45X_StdPeriph_Driver * @{ */ /** @addtogroup TIM * @brief TIM driver modules * @{ */ /** @addtogroup TIM_Private_TypesDefinitions * @{ */ /** * @} */ /** @addtogroup TIM_Private_Defines * @{ */ /* ---------------------- TIM registers bit mask ------------------------ */ #define SMCTRL_ETR_MASK ((uint16_t)0x00FF) #define CAPCMPMOD_OFFSET ((uint16_t)0x0018) #define CAPCMPEN_CCE_SET ((uint16_t)0x0001) #define CAPCMPEN_CCNE_SET ((uint16_t)0x0004) /** * @} */ /** @addtogroup TIM_Private_Macros * @{ */ /** * @} */ /** @addtogroup TIM_Private_Variables * @{ */ /** * @} */ /** @addtogroup TIM_Private_FunctionPrototypes * @{ */ static void ConfigTI1(TIM_Module* TIMx, uint16_t IcPolarity, uint16_t IcSelection, uint16_t IcFilter); static void ConfigTI2(TIM_Module* TIMx, uint16_t IcPolarity, uint16_t IcSelection, uint16_t IcFilter); static void ConfigTI3(TIM_Module* TIMx, uint16_t IcPolarity, uint16_t IcSelection, uint16_t IcFilter); static void ConfigTI4(TIM_Module* TIMx, uint16_t IcPolarity, uint16_t IcSelection, uint16_t IcFilter); /** * @} */ /** @addtogroup TIM_Private_Macros * @{ */ /** * @} */ /** @addtogroup TIM_Private_Variables * @{ */ /** * @} */ /** @addtogroup TIM_Private_FunctionPrototypes * @{ */ /** * @} */ /** @addtogroup TIM_Private_Functions * @{ */ /** * @brief Deinitializes the TIMx peripheral registers to their default reset values. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. */ void TIM_DeInit(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); if (TIMx == TIM1) { RCC_EnableAPB2PeriphReset(RCC_APB2_PERIPH_TIM1, ENABLE); RCC_EnableAPB2PeriphReset(RCC_APB2_PERIPH_TIM1, DISABLE); } else if (TIMx == TIM2) { RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM2, ENABLE); RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM2, DISABLE); } else if (TIMx == TIM3) { RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM3, ENABLE); RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM3, DISABLE); } else if (TIMx == TIM4) { RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM4, ENABLE); RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM4, DISABLE); } else if (TIMx == TIM5) { RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM5, ENABLE); RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM5, DISABLE); } else if (TIMx == TIM6) { RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM6, ENABLE); RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM6, DISABLE); } else if (TIMx == TIM7) { RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM7, ENABLE); RCC_EnableAPB1PeriphReset(RCC_APB1_PERIPH_TIM7, DISABLE); } else if (TIMx == TIM8) { RCC_EnableAPB2PeriphReset(RCC_APB2_PERIPH_TIM8, ENABLE); RCC_EnableAPB2PeriphReset(RCC_APB2_PERIPH_TIM8, DISABLE); } } /** * @brief Initializes the TIMx Time Base Unit peripheral according to * the specified parameters in the TIM_TimeBaseInitStruct. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param TIM_TimeBaseInitStruct pointer to a TIM_TimeBaseInitType * structure that contains the configuration information for the * specified TIM peripheral. */ void TIM_InitTimeBase(TIM_Module* TIMx, TIM_TimeBaseInitType* TIM_TimeBaseInitStruct) { uint32_t tmpcr1 = 0; /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimCntMode(TIM_TimeBaseInitStruct->CntMode)); assert_param(IsTimClkDiv(TIM_TimeBaseInitStruct->ClkDiv)); tmpcr1 = TIMx->CTRL1; if ((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4) || (TIMx == TIM5)) { /* Select the Counter Mode */ tmpcr1 &= (uint32_t)(~((uint32_t)(TIM_CTRL1_DIR | TIM_CTRL1_CAMSEL))); tmpcr1 |= (uint32_t)TIM_TimeBaseInitStruct->CntMode; } if ((TIMx != TIM6) && (TIMx != TIM7)) { /* Set the clock division */ tmpcr1 &= (uint32_t)(~((uint32_t)TIM_CTRL1_CLKD)); tmpcr1 |= (uint32_t)TIM_TimeBaseInitStruct->ClkDiv; } TIMx->CTRL1 = tmpcr1; /* Set the Autoreload value */ TIMx->AR = TIM_TimeBaseInitStruct->Period; /* Set the Prescaler value */ TIMx->PSC = TIM_TimeBaseInitStruct->Prescaler; if ((TIMx == TIM1) || (TIMx == TIM8)) { /* Set the Repetition Counter value */ TIMx->REPCNT = TIM_TimeBaseInitStruct->RepetCnt; } /* Generate an update event to reload the Prescaler and the Repetition counter values immediately */ TIMx->EVTGEN = TIM_PSC_RELOAD_MODE_IMMEDIATE; /*channel input from comp or iom*/ tmpcr1 = TIMx->CTRL1; if ((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4) || (TIMx == TIM5)) { if (TIM_TimeBaseInitStruct->CapCh1FromCompEn) tmpcr1 |= (0x01L << 11); else tmpcr1 &= ~(0x01L << 11); } if ((TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4) || (TIMx == TIM5)) { if (TIM_TimeBaseInitStruct->CapCh2FromCompEn) tmpcr1 |= (0x01L << 12); else tmpcr1 &= ~(0x01L << 12); if (TIM_TimeBaseInitStruct->CapCh3FromCompEn) tmpcr1 |= (0x01L << 13); else tmpcr1 &= ~(0x01L << 13); } if ((TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4)) { if (TIM_TimeBaseInitStruct->CapCh4FromCompEn) tmpcr1 |= (0x01L << 14); else tmpcr1 &= ~(0x01L << 14); } /*etr input from comp or iom*/ if ((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4)) { if (TIM_TimeBaseInitStruct->CapEtrClrFromCompEn) tmpcr1 |= (0x01L << 15); else tmpcr1 &= ~(0x01L << 15); } TIMx->CTRL1 = tmpcr1; /*sel etr from iom or tsc*/ tmpcr1 = TIMx->CTRL2; if ((TIMx == TIM2) || (TIMx == TIM4)) { if (TIM_TimeBaseInitStruct->CapEtrSelFromTscEn) tmpcr1 |= (0x01L << 8); else tmpcr1 &= ~(0x01L << 8); } TIMx->CTRL2 = tmpcr1; } /** * @brief Initializes the TIMx Channel1 according to the specified * parameters in the TIM_OCInitStruct. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param TIM_OCInitStruct pointer to a OCInitType structure * that contains the configuration information for the specified TIM peripheral. */ void TIM_InitOc1(TIM_Module* TIMx, OCInitType* TIM_OCInitStruct) { uint16_t tmpccmrx = 0; uint32_t tmpccer = 0, tmpcr2 = 0; /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimOcMode(TIM_OCInitStruct->OcMode)); assert_param(IsTimOutputState(TIM_OCInitStruct->OutputState)); assert_param(IsTimOcPolarity(TIM_OCInitStruct->OcPolarity)); /* Disable the Channel 1: Reset the CC1E Bit */ TIMx->CCEN &= (uint32_t)(~(uint32_t)TIM_CCEN_CC1EN); /* Get the TIMx CCEN register value */ tmpccer = TIMx->CCEN; /* Get the TIMx CTRL2 register value */ tmpcr2 = TIMx->CTRL2; /* Get the TIMx CCMOD1 register value */ tmpccmrx = TIMx->CCMOD1; /* Reset the Output Compare Mode Bits */ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD1_OC1M)); tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD1_CC1SEL)); /* Select the Output Compare Mode */ tmpccmrx |= TIM_OCInitStruct->OcMode; /* Reset the Output Polarity level */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC1P)); /* Set the Output Compare Polarity */ tmpccer |= TIM_OCInitStruct->OcPolarity; /* Set the Output State */ tmpccer |= TIM_OCInitStruct->OutputState; if ((TIMx == TIM1) || (TIMx == TIM8)) { assert_param(IsTimOutputNState(TIM_OCInitStruct->OutputNState)); assert_param(IsTimOcnPolarity(TIM_OCInitStruct->OcNPolarity)); assert_param(IsTimOcnIdleState(TIM_OCInitStruct->OcNIdleState)); assert_param(IsTimOcIdleState(TIM_OCInitStruct->OcIdleState)); /* Reset the Output N Polarity level */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC1NP)); /* Set the Output N Polarity */ tmpccer |= TIM_OCInitStruct->OcNPolarity; /* Reset the Output N State */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC1NEN)); /* Set the Output N State */ tmpccer |= TIM_OCInitStruct->OutputNState; /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI1)); tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI1N)); /* Set the Output Idle state */ tmpcr2 |= TIM_OCInitStruct->OcIdleState; /* Set the Output N Idle state */ tmpcr2 |= TIM_OCInitStruct->OcNIdleState; } /* Write to TIMx CTRL2 */ TIMx->CTRL2 = tmpcr2; /* Write to TIMx CCMOD1 */ TIMx->CCMOD1 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCDAT1 = TIM_OCInitStruct->Pulse; /* Write to TIMx CCEN */ TIMx->CCEN = tmpccer; } /** * @brief Initializes the TIMx Channel2 according to the specified * parameters in the TIM_OCInitStruct. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select * the TIM peripheral. * @param TIM_OCInitStruct pointer to a OCInitType structure * that contains the configuration information for the specified TIM peripheral. */ void TIM_InitOc2(TIM_Module* TIMx, OCInitType* TIM_OCInitStruct) { uint16_t tmpccmrx = 0; uint32_t tmpccer = 0, tmpcr2 = 0; /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimOcMode(TIM_OCInitStruct->OcMode)); assert_param(IsTimOutputState(TIM_OCInitStruct->OutputState)); assert_param(IsTimOcPolarity(TIM_OCInitStruct->OcPolarity)); /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCEN &= (uint32_t)(~((uint32_t)TIM_CCEN_CC2EN)); /* Get the TIMx CCEN register value */ tmpccer = TIMx->CCEN; /* Get the TIMx CTRL2 register value */ tmpcr2 = TIMx->CTRL2; /* Get the TIMx CCMOD1 register value */ tmpccmrx = TIMx->CCMOD1; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD1_OC2M)); tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD1_CC2SEL)); /* Select the Output Compare Mode */ tmpccmrx |= (uint16_t)(TIM_OCInitStruct->OcMode << 8); /* Reset the Output Polarity level */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC2P)); /* Set the Output Compare Polarity */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OcPolarity << 4); /* Set the Output State */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OutputState << 4); if ((TIMx == TIM1) || (TIMx == TIM8)) { assert_param(IsTimOutputNState(TIM_OCInitStruct->OutputNState)); assert_param(IsTimOcnPolarity(TIM_OCInitStruct->OcNPolarity)); assert_param(IsTimOcnIdleState(TIM_OCInitStruct->OcNIdleState)); assert_param(IsTimOcIdleState(TIM_OCInitStruct->OcIdleState)); /* Reset the Output N Polarity level */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC2NP)); /* Set the Output N Polarity */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OcNPolarity << 4); /* Reset the Output N State */ tmpccer &= (uint32_t)(~((uint16_t)TIM_CCEN_CC2NEN)); /* Set the Output N State */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OutputNState << 4); /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI2)); tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI2N)); /* Set the Output Idle state */ tmpcr2 |= (uint32_t)(TIM_OCInitStruct->OcIdleState << 2); /* Set the Output N Idle state */ tmpcr2 |= (uint32_t)(TIM_OCInitStruct->OcNIdleState << 2); } /* Write to TIMx CTRL2 */ TIMx->CTRL2 = tmpcr2; /* Write to TIMx CCMOD1 */ TIMx->CCMOD1 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCDAT2 = TIM_OCInitStruct->Pulse; /* Write to TIMx CCEN */ TIMx->CCEN = tmpccer; } /** * @brief Initializes the TIMx Channel3 according to the specified * parameters in the TIM_OCInitStruct. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCInitStruct pointer to a OCInitType structure * that contains the configuration information for the specified TIM peripheral. */ void TIM_InitOc3(TIM_Module* TIMx, OCInitType* TIM_OCInitStruct) { uint16_t tmpccmrx = 0; uint32_t tmpccer = 0, tmpcr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcMode(TIM_OCInitStruct->OcMode)); assert_param(IsTimOutputState(TIM_OCInitStruct->OutputState)); assert_param(IsTimOcPolarity(TIM_OCInitStruct->OcPolarity)); /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCEN &= (uint32_t)(~((uint32_t)TIM_CCEN_CC3EN)); /* Get the TIMx CCEN register value */ tmpccer = TIMx->CCEN; /* Get the TIMx CTRL2 register value */ tmpcr2 = TIMx->CTRL2; /* Get the TIMx CCMOD2 register value */ tmpccmrx = TIMx->CCMOD2; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD2_OC3MD)); tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD2_CC3SEL)); /* Select the Output Compare Mode */ tmpccmrx |= TIM_OCInitStruct->OcMode; /* Reset the Output Polarity level */ tmpccer &= (uint32_t)(~((uint16_t)TIM_CCEN_CC3P)); /* Set the Output Compare Polarity */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OcPolarity << 8); /* Set the Output State */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OutputState << 8); if ((TIMx == TIM1) || (TIMx == TIM8)) { assert_param(IsTimOutputNState(TIM_OCInitStruct->OutputNState)); assert_param(IsTimOcnPolarity(TIM_OCInitStruct->OcNPolarity)); assert_param(IsTimOcnIdleState(TIM_OCInitStruct->OcNIdleState)); assert_param(IsTimOcIdleState(TIM_OCInitStruct->OcIdleState)); /* Reset the Output N Polarity level */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC3NP)); /* Set the Output N Polarity */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OcNPolarity << 8); /* Reset the Output N State */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC3NEN)); /* Set the Output N State */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OutputNState << 8); /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI3)); tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI3N)); /* Set the Output Idle state */ tmpcr2 |= (uint32_t)(TIM_OCInitStruct->OcIdleState << 4); /* Set the Output N Idle state */ tmpcr2 |= (uint32_t)(TIM_OCInitStruct->OcNIdleState << 4); } /* Write to TIMx CTRL2 */ TIMx->CTRL2 = tmpcr2; /* Write to TIMx CCMOD2 */ TIMx->CCMOD2 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCDAT3 = TIM_OCInitStruct->Pulse; /* Write to TIMx CCEN */ TIMx->CCEN = tmpccer; } /** * @brief Initializes the TIMx Channel4 according to the specified * parameters in the TIM_OCInitStruct. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCInitStruct pointer to a OCInitType structure * that contains the configuration information for the specified TIM peripheral. */ void TIM_InitOc4(TIM_Module* TIMx, OCInitType* TIM_OCInitStruct) { uint16_t tmpccmrx = 0; uint32_t tmpccer = 0, tmpcr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcMode(TIM_OCInitStruct->OcMode)); assert_param(IsTimOutputState(TIM_OCInitStruct->OutputState)); assert_param(IsTimOcPolarity(TIM_OCInitStruct->OcPolarity)); /* Disable the Channel 2: Reset the CC4E Bit */ TIMx->CCEN &= (uint32_t)(~((uint32_t)TIM_CCEN_CC4EN)); /* Get the TIMx CCEN register value */ tmpccer = TIMx->CCEN; /* Get the TIMx CTRL2 register value */ tmpcr2 = TIMx->CTRL2; /* Get the TIMx CCMOD2 register value */ tmpccmrx = TIMx->CCMOD2; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD2_OC4MD)); tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD2_CC4SEL)); /* Select the Output Compare Mode */ tmpccmrx |= (uint16_t)(TIM_OCInitStruct->OcMode << 8); /* Reset the Output Polarity level */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC4P)); /* Set the Output Compare Polarity */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OcPolarity << 12); /* Set the Output State */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OutputState << 12); if ((TIMx == TIM1) || (TIMx == TIM8)) { assert_param(IsTimOcIdleState(TIM_OCInitStruct->OcIdleState)); /* Reset the Output Compare IDLE State */ tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI4)); /* Set the Output Idle state */ tmpcr2 |= (uint32_t)(TIM_OCInitStruct->OcIdleState << 6); } /* Write to TIMx CTRL2 */ TIMx->CTRL2 = tmpcr2; /* Write to TIMx CCMOD2 */ TIMx->CCMOD2 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCDAT4 = TIM_OCInitStruct->Pulse; /* Write to TIMx CCEN */ TIMx->CCEN = tmpccer; } /** * @brief Initializes the TIMx Channel5 according to the specified * parameters in the TIM_OCInitStruct. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_OCInitStruct pointer to a OCInitType structure * that contains the configuration information for the specified TIM peripheral. */ void TIM_InitOc5(TIM_Module* TIMx, OCInitType* TIM_OCInitStruct) { uint16_t tmpccmrx = 0; uint32_t tmpccer = 0, tmpcr2 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcMode(TIM_OCInitStruct->OcMode)); assert_param(IsTimOutputState(TIM_OCInitStruct->OutputState)); assert_param(IsTimOcPolarity(TIM_OCInitStruct->OcPolarity)); /* Disable the Channel 5: Reset the CC5E Bit */ TIMx->CCEN &= (uint32_t)(~((uint32_t)TIM_CCEN_CC5EN)); /* Get the TIMx CCEN register value */ tmpccer = TIMx->CCEN; /* Get the TIMx CTRL2 register value */ tmpcr2 = TIMx->CTRL2; /* Get the TIMx CCMOD3 register value */ tmpccmrx = TIMx->CCMOD3; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD3_OC5MD)); /* Select the Output Compare Mode */ tmpccmrx |= (uint16_t)(TIM_OCInitStruct->OcMode); /* Reset the Output Polarity level */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC5P)); /* Set the Output Compare Polarity */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OcPolarity << 16); /* Set the Output State */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OutputState << 16); if ((TIMx == TIM1) || (TIMx == TIM8)) { assert_param(IsTimOcIdleState(TIM_OCInitStruct->OcIdleState)); /* Reset the Output Compare IDLE State */ tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI5)); /* Set the Output Idle state */ tmpcr2 |= (uint32_t)(TIM_OCInitStruct->OcIdleState << 8); } /* Write to TIMx CTRL2 */ TIMx->CTRL2 = tmpcr2; /* Write to TIMx CCMOD3 */ TIMx->CCMOD3 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCDAT5 = TIM_OCInitStruct->Pulse; /* Write to TIMx CCEN */ TIMx->CCEN = tmpccer; } /** * @brief Initializes the TIMx Channel6 according to the specified * parameters in the TIM_OCInitStruct. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_OCInitStruct pointer to a OCInitType structure * that contains the configuration information for the specified TIM peripheral. */ void TIM_InitOc6(TIM_Module* TIMx, OCInitType* TIM_OCInitStruct) { uint16_t tmpccmrx = 0; uint32_t tmpccer = 0, tmpcr2 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcMode(TIM_OCInitStruct->OcMode)); assert_param(IsTimOutputState(TIM_OCInitStruct->OutputState)); assert_param(IsTimOcPolarity(TIM_OCInitStruct->OcPolarity)); /* Disable the Channel 6: Reset the CC6E Bit */ TIMx->CCEN &= (uint32_t)(~((uint32_t)TIM_CCEN_CC6EN)); /* Get the TIMx CCEN register value */ tmpccer = TIMx->CCEN; /* Get the TIMx CTRL2 register value */ tmpcr2 = TIMx->CTRL2; /* Get the TIMx CCMOD3 register value */ tmpccmrx = TIMx->CCMOD3; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMOD3_OC6MD)); /* Select the Output Compare Mode */ tmpccmrx |= (uint16_t)(TIM_OCInitStruct->OcMode << 8); /* Reset the Output Polarity level */ tmpccer &= (uint32_t)(~((uint32_t)TIM_CCEN_CC6P)); /* Set the Output Compare Polarity */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OcPolarity << 20); /* Set the Output State */ tmpccer |= (uint32_t)(TIM_OCInitStruct->OutputState << 20); if ((TIMx == TIM1) || (TIMx == TIM8)) { assert_param(IsTimOcIdleState(TIM_OCInitStruct->OcIdleState)); /* Reset the Output Compare IDLE State */ tmpcr2 &= (uint32_t)(~((uint32_t)TIM_CTRL2_OI6)); /* Set the Output Idle state */ tmpcr2 |= (uint32_t)(TIM_OCInitStruct->OcIdleState << 10); } /* Write to TIMx CTRL2 */ TIMx->CTRL2 = tmpcr2; /* Write to TIMx CCMOD3 */ TIMx->CCMOD3 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCDAT6 = TIM_OCInitStruct->Pulse; /* Write to TIMx CCEN */ TIMx->CCEN = tmpccer; } /** * @brief Initializes the TIM peripheral according to the specified * parameters in the TIM_ICInitStruct. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param TIM_ICInitStruct pointer to a TIM_ICInitType structure * that contains the configuration information for the specified TIM peripheral. */ void TIM_ICInit(TIM_Module* TIMx, TIM_ICInitType* TIM_ICInitStruct) { /* Check the parameters */ assert_param(IsTimCh(TIM_ICInitStruct->Channel)); assert_param(IsTimIcSelection(TIM_ICInitStruct->IcSelection)); assert_param(IsTimIcPrescaler(TIM_ICInitStruct->IcPrescaler)); assert_param(IsTimInCapFilter(TIM_ICInitStruct->IcFilter)); if ((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4) || (TIMx == TIM5)) { assert_param(IsTimIcPalaritySingleEdge(TIM_ICInitStruct->IcPolarity)); } else { assert_param(IsTimIcPolarityAnyEdge(TIM_ICInitStruct->IcPolarity)); } if (TIM_ICInitStruct->Channel == TIM_CH_1) { assert_param(IsTimList8Module(TIMx)); /* TI1 Configuration */ ConfigTI1(TIMx, TIM_ICInitStruct->IcPolarity, TIM_ICInitStruct->IcSelection, TIM_ICInitStruct->IcFilter); /* Set the Input Capture Prescaler value */ TIM_SetInCap1Prescaler(TIMx, TIM_ICInitStruct->IcPrescaler); } else if (TIM_ICInitStruct->Channel == TIM_CH_2) { assert_param(IsTimList6Module(TIMx)); /* TI2 Configuration */ ConfigTI2(TIMx, TIM_ICInitStruct->IcPolarity, TIM_ICInitStruct->IcSelection, TIM_ICInitStruct->IcFilter); /* Set the Input Capture Prescaler value */ TIM_SetInCap2Prescaler(TIMx, TIM_ICInitStruct->IcPrescaler); } else if (TIM_ICInitStruct->Channel == TIM_CH_3) { assert_param(IsTimList3Module(TIMx)); /* TI3 Configuration */ ConfigTI3(TIMx, TIM_ICInitStruct->IcPolarity, TIM_ICInitStruct->IcSelection, TIM_ICInitStruct->IcFilter); /* Set the Input Capture Prescaler value */ TIM_SetInCap3Prescaler(TIMx, TIM_ICInitStruct->IcPrescaler); } else { assert_param(IsTimList3Module(TIMx)); /* TI4 Configuration */ ConfigTI4(TIMx, TIM_ICInitStruct->IcPolarity, TIM_ICInitStruct->IcSelection, TIM_ICInitStruct->IcFilter); /* Set the Input Capture Prescaler value */ TIM_SetInCap4Prescaler(TIMx, TIM_ICInitStruct->IcPrescaler); } } /** * @brief Configures the TIM peripheral according to the specified * parameters in the TIM_ICInitStruct to measure an external PWM signal. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param TIM_ICInitStruct pointer to a TIM_ICInitType structure * that contains the configuration information for the specified TIM peripheral. */ void TIM_ConfigPwmIc(TIM_Module* TIMx, TIM_ICInitType* TIM_ICInitStruct) { uint16_t icoppositepolarity = TIM_IC_POLARITY_RISING; uint16_t icoppositeselection = TIM_IC_SELECTION_DIRECTTI; /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); /* Select the Opposite Input Polarity */ if (TIM_ICInitStruct->IcPolarity == TIM_IC_POLARITY_RISING) { icoppositepolarity = TIM_IC_POLARITY_FALLING; } else { icoppositepolarity = TIM_IC_POLARITY_RISING; } /* Select the Opposite Input */ if (TIM_ICInitStruct->IcSelection == TIM_IC_SELECTION_DIRECTTI) { icoppositeselection = TIM_IC_SELECTION_INDIRECTTI; } else { icoppositeselection = TIM_IC_SELECTION_DIRECTTI; } if (TIM_ICInitStruct->Channel == TIM_CH_1) { /* TI1 Configuration */ ConfigTI1(TIMx, TIM_ICInitStruct->IcPolarity, TIM_ICInitStruct->IcSelection, TIM_ICInitStruct->IcFilter); /* Set the Input Capture Prescaler value */ TIM_SetInCap1Prescaler(TIMx, TIM_ICInitStruct->IcPrescaler); /* TI2 Configuration */ ConfigTI2(TIMx, icoppositepolarity, icoppositeselection, TIM_ICInitStruct->IcFilter); /* Set the Input Capture Prescaler value */ TIM_SetInCap2Prescaler(TIMx, TIM_ICInitStruct->IcPrescaler); } else { /* TI2 Configuration */ ConfigTI2(TIMx, TIM_ICInitStruct->IcPolarity, TIM_ICInitStruct->IcSelection, TIM_ICInitStruct->IcFilter); /* Set the Input Capture Prescaler value */ TIM_SetInCap2Prescaler(TIMx, TIM_ICInitStruct->IcPrescaler); /* TI1 Configuration */ ConfigTI1(TIMx, icoppositepolarity, icoppositeselection, TIM_ICInitStruct->IcFilter); /* Set the Input Capture Prescaler value */ TIM_SetInCap1Prescaler(TIMx, TIM_ICInitStruct->IcPrescaler); } } /** * @brief Configures the: Break feature, dead time, Lock level, the OSSI, * the OSSR State and the AOE(automatic output enable). * @param TIMx where x can be 1 or 8 to select the TIM * @param TIM_BDTRInitStruct pointer to a TIM_BDTRInitType structure that * contains the BKDT Register configuration information for the TIM peripheral. */ void TIM_ConfigBkdt(TIM_Module* TIMx, TIM_BDTRInitType* TIM_BDTRInitStruct) { uint32_t tmp; /* Check the parameters */ assert_param(IsTimList2Module(TIMx)); assert_param(IsTimOssrState(TIM_BDTRInitStruct->OssrState)); assert_param(IsTimOssiState(TIM_BDTRInitStruct->OssiState)); assert_param(IsTimLockLevel(TIM_BDTRInitStruct->LockLevel)); assert_param(IsTimBreakInState(TIM_BDTRInitStruct->Break)); assert_param(IsTimBreakPalarity(TIM_BDTRInitStruct->BreakPolarity)); assert_param(IsTimAutoOutputState(TIM_BDTRInitStruct->AutomaticOutput)); /* Set the Lock level, the Break enable Bit and the Ploarity, the OSSR State, the OSSI State, the dead time value and the Automatic Output Enable Bit */ TIMx->BKDT = (uint32_t)TIM_BDTRInitStruct->OssrState | TIM_BDTRInitStruct->OssiState | TIM_BDTRInitStruct->LockLevel | TIM_BDTRInitStruct->DeadTime | TIM_BDTRInitStruct->Break | TIM_BDTRInitStruct->BreakPolarity | TIM_BDTRInitStruct->AutomaticOutput; /*cofigure other break in*/ tmp = TIMx->CTRL1; /*IOMBKPEN 0 meaning iom as break enable*/ if (TIM_BDTRInitStruct->IomBreakEn) tmp &= ~(0x01L << 10); else tmp |= (0x01L << 10); if (TIM_BDTRInitStruct->LockUpBreakEn) tmp |= (0x01L << 16); else tmp &= ~(0x01L << 16); if (TIM_BDTRInitStruct->PvdBreakEn) tmp |= (0x01L << 17); else tmp &= ~(0x01L << 17); TIMx->CTRL1 = tmp; } /** * @brief Fills each TIM_TimeBaseInitStruct member with its default value. * @param TIM_TimeBaseInitStruct pointer to a TIM_TimeBaseInitType * structure which will be initialized. */ void TIM_InitTimBaseStruct(TIM_TimeBaseInitType* TIM_TimeBaseInitStruct) { /* Set the default configuration */ TIM_TimeBaseInitStruct->Period = 0xFFFF; TIM_TimeBaseInitStruct->Prescaler = 0x0000; TIM_TimeBaseInitStruct->ClkDiv = TIM_CLK_DIV1; TIM_TimeBaseInitStruct->CntMode = TIM_CNT_MODE_UP; TIM_TimeBaseInitStruct->RepetCnt = 0x0000; TIM_TimeBaseInitStruct->CapCh1FromCompEn = false; TIM_TimeBaseInitStruct->CapCh2FromCompEn = false; TIM_TimeBaseInitStruct->CapCh3FromCompEn = false; TIM_TimeBaseInitStruct->CapCh4FromCompEn = false; TIM_TimeBaseInitStruct->CapEtrClrFromCompEn = false; TIM_TimeBaseInitStruct->CapEtrSelFromTscEn = false; } /** * @brief Fills each TIM_OCInitStruct member with its default value. * @param TIM_OCInitStruct pointer to a OCInitType structure which will * be initialized. */ void TIM_InitOcStruct(OCInitType* TIM_OCInitStruct) { /* Set the default configuration */ TIM_OCInitStruct->OcMode = TIM_OCMODE_TIMING; TIM_OCInitStruct->OutputState = TIM_OUTPUT_STATE_DISABLE; TIM_OCInitStruct->OutputNState = TIM_OUTPUT_NSTATE_DISABLE; TIM_OCInitStruct->Pulse = 0x0000; TIM_OCInitStruct->OcPolarity = TIM_OC_POLARITY_HIGH; TIM_OCInitStruct->OcNPolarity = TIM_OC_POLARITY_HIGH; TIM_OCInitStruct->OcIdleState = TIM_OC_IDLE_STATE_RESET; TIM_OCInitStruct->OcNIdleState = TIM_OCN_IDLE_STATE_RESET; } /** * @brief Fills each TIM_ICInitStruct member with its default value. * @param TIM_ICInitStruct pointer to a TIM_ICInitType structure which will * be initialized. */ void TIM_InitIcStruct(TIM_ICInitType* TIM_ICInitStruct) { /* Set the default configuration */ TIM_ICInitStruct->Channel = TIM_CH_1; TIM_ICInitStruct->IcPolarity = TIM_IC_POLARITY_RISING; TIM_ICInitStruct->IcSelection = TIM_IC_SELECTION_DIRECTTI; TIM_ICInitStruct->IcPrescaler = TIM_IC_PSC_DIV1; TIM_ICInitStruct->IcFilter = 0x00; } /** * @brief Fills each TIM_BDTRInitStruct member with its default value. * @param TIM_BDTRInitStruct pointer to a TIM_BDTRInitType structure which * will be initialized. */ void TIM_InitBkdtStruct(TIM_BDTRInitType* TIM_BDTRInitStruct) { /* Set the default configuration */ TIM_BDTRInitStruct->OssrState = TIM_OSSR_STATE_DISABLE; TIM_BDTRInitStruct->OssiState = TIM_OSSI_STATE_DISABLE; TIM_BDTRInitStruct->LockLevel = TIM_LOCK_LEVEL_OFF; TIM_BDTRInitStruct->DeadTime = 0x00; TIM_BDTRInitStruct->Break = TIM_BREAK_IN_DISABLE; TIM_BDTRInitStruct->BreakPolarity = TIM_BREAK_POLARITY_LOW; TIM_BDTRInitStruct->AutomaticOutput = TIM_AUTO_OUTPUT_DISABLE; } /** * @brief Enables or disables the specified TIM peripheral. * @param TIMx where x can be 1 to 8 to select the TIMx peripheral. * @param Cmd new state of the TIMx peripheral. * This parameter can be: ENABLE or DISABLE. */ void TIM_Enable(TIM_Module* TIMx, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Enable the TIM Counter */ TIMx->CTRL1 |= TIM_CTRL1_CNTEN; } else { /* Disable the TIM Counter */ TIMx->CTRL1 &= (uint32_t)(~((uint32_t)TIM_CTRL1_CNTEN)); } } /** * @brief Enables or disables the TIM peripheral Main Outputs. * @param TIMx where x can be 1, 8 to select the TIMx peripheral. * @param Cmd new state of the TIM peripheral Main Outputs. * This parameter can be: ENABLE or DISABLE. */ void TIM_EnableCtrlPwmOutputs(TIM_Module* TIMx, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimList2Module(TIMx)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Enable the TIM Main Output */ TIMx->BKDT |= TIM_BKDT_MOEN; } else { /* Disable the TIM Main Output */ TIMx->BKDT &= (uint16_t)(~((uint16_t)TIM_BKDT_MOEN)); } } /** * @brief Enables or disables the specified TIM interrupts. * @param TIMx where x can be 1 to 8 to select the TIMx peripheral. * @param TIM_IT specifies the TIM interrupts sources to be enabled or disabled. * This parameter can be any combination of the following values: * @arg TIM_INT_UPDATE TIM update Interrupt source * @arg TIM_INT_CC1 TIM Capture Compare 1 Interrupt source * @arg TIM_INT_CC2 TIM Capture Compare 2 Interrupt source * @arg TIM_INT_CC3 TIM Capture Compare 3 Interrupt source * @arg TIM_INT_CC4 TIM Capture Compare 4 Interrupt source * @arg TIM_INT_COM TIM Commutation Interrupt source * @arg TIM_INT_TRIG TIM Trigger Interrupt source * @arg TIM_INT_BREAK TIM Break Interrupt source * @note * - TIM6 and TIM7 can only generate an update interrupt. * - TIM_INT_BREAK is used only with TIM1, TIM8. * - TIM_INT_COM is used only with TIM1, TIM8. * @param Cmd new state of the TIM interrupts. * This parameter can be: ENABLE or DISABLE. */ void TIM_ConfigInt(TIM_Module* TIMx, uint16_t TIM_IT, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimInt(TIM_IT)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Enable the Interrupt sources */ TIMx->DINTEN |= TIM_IT; } else { /* Disable the Interrupt sources */ TIMx->DINTEN &= (uint16_t)~TIM_IT; } } /** * @brief Configures the TIMx event to be generate by software. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param TIM_EventSource specifies the event source. * This parameter can be one or more of the following values: * @arg TIM_EVT_SRC_UPDATE Timer update Event source * @arg TIM_EVT_SRC_CC1 Timer Capture Compare 1 Event source * @arg TIM_EVT_SRC_CC2 Timer Capture Compare 2 Event source * @arg TIM_EVT_SRC_CC3 Timer Capture Compare 3 Event source * @arg TIM_EVT_SRC_CC4 Timer Capture Compare 4 Event source * @arg TIM_EVT_SRC_COM Timer COM event source * @arg TIM_EVT_SRC_TRIG Timer Trigger Event source * @arg TIM_EVT_SRC_BREAK Timer Break event source * @note * - TIM6 and TIM7 can only generate an update event. * - TIM_EVT_SRC_COM and TIM_EVT_SRC_BREAK are used only with TIM1 and TIM8. */ void TIM_GenerateEvent(TIM_Module* TIMx, uint16_t TIM_EventSource) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimEvtSrc(TIM_EventSource)); /* Set the event sources */ TIMx->EVTGEN = TIM_EventSource; } /** * @brief Configures the TIMx's DMA interface. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select * the TIM peripheral. * @param TIM_DMABase DMA Base address. * This parameter can be one of the following values: * @arg TIM_DMABase_CR, TIM_DMABASE_CTRL2, TIM_DMABASE_SMCTRL, * TIM_DMABASE_DMAINTEN, TIM1_DMABase_SR, TIM_DMABASE_EVTGEN, * TIM_DMABASE_CAPCMPMOD1, TIM_DMABASE_CAPCMPMOD2, TIM_DMABASE_CAPCMPEN, * TIM_DMABASE_CNT, TIM_DMABASE_PSC, TIM_DMABASE_AR, * TIM_DMABASE_REPCNT, TIM_DMABASE_CAPCMPDAT1, TIM_DMABASE_CAPCMPDAT2, * TIM_DMABASE_CAPCMPDAT3, TIM_DMABASE_CAPCMPDAT4, TIM_DMABASE_BKDT, * TIM_DMABASE_CAPCMPMOD3, TIM_DMABASE_CAPCMPDAT5, TIM_DMABASE_CAPCMPDAT6, * TIM_DMABASE_DMACTRL. * @param TIM_DMABurstLength DMA Burst length. * This parameter can be one value between: * TIM_DMABURST_LENGTH_1TRANSFER and TIM_DMABURST_LENGTH_18TRANSFERS. */ void TIM_ConfigDma(TIM_Module* TIMx, uint16_t TIM_DMABase, uint16_t TIM_DMABurstLength) { /* Check the parameters */ assert_param(IsTimList4Module(TIMx)); assert_param(IsTimDmaBase(TIM_DMABase)); assert_param(IsTimDmaLength(TIM_DMABurstLength)); /* Set the DMA Base and the DMA Burst Length */ TIMx->DCTRL = TIM_DMABase | TIM_DMABurstLength; } /** * @brief Enables or disables the TIMx's DMA Requests. * @param TIMx where x can be 1, 2, 3, 4, 5, 6, 7, 8 * to select the TIM peripheral. * @param TIM_DMASource specifies the DMA Request sources. * This parameter can be any combination of the following values: * @arg TIM_DMA_UPDATE TIM update Interrupt source * @arg TIM_DMA_CC1 TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2 TIM Capture Compare 2 DMA source * @arg TIM_DMA_CC3 TIM Capture Compare 3 DMA source * @arg TIM_DMA_CC4 TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM TIM Commutation DMA source * @arg TIM_DMA_TRIG TIM Trigger DMA source * @param Cmd new state of the DMA Request sources. * This parameter can be: ENABLE or DISABLE. */ void TIM_EnableDma(TIM_Module* TIMx, uint16_t TIM_DMASource, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimList9Module(TIMx)); assert_param(IsTimDmaSrc(TIM_DMASource)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Enable the DMA sources */ TIMx->DINTEN |= TIM_DMASource; } else { /* Disable the DMA sources */ TIMx->DINTEN &= (uint16_t)~TIM_DMASource; } } /** * @brief Configures the TIMx internal Clock * @param TIMx where x can be 1, 2, 3, 4, 5, 8 * to select the TIM peripheral. */ void TIM_ConfigInternalClk(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); /* Disable slave mode to clock the prescaler directly with the internal clock */ TIMx->SMCTRL &= (uint16_t)(~((uint16_t)TIM_SMCTRL_SMSEL)); } /** * @brief Configures the TIMx Internal Trigger as External Clock * @param TIMx where x can be 1, 2, 3, 4, 5 to select the TIM peripheral. * @param TIM_InputTriggerSource Trigger source. * This parameter can be one of the following values: * @arg TIM_TRIG_SEL_IN_TR0 Internal Trigger 0 * @arg TIM_TRIG_SEL_IN_TR1 Internal Trigger 1 * @arg TIM_TRIG_SEL_IN_TR2 Internal Trigger 2 * @arg TIM_TRIG_SEL_IN_TR3 Internal Trigger 3 */ void TIM_ConfigInternalTrigToExt(TIM_Module* TIMx, uint16_t TIM_InputTriggerSource) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimInterTrigSel(TIM_InputTriggerSource)); /* Select the Internal Trigger */ TIM_SelectInputTrig(TIMx, TIM_InputTriggerSource); /* Select the External clock mode1 */ TIMx->SMCTRL |= TIM_SLAVE_MODE_EXT1; } /** * @brief Configures the TIMx Trigger as External Clock * @param TIMx where x can be 1, 2, 3, 4, 5 to select the TIM peripheral. * @param TIM_TIxExternalCLKSource Trigger source. * This parameter can be one of the following values: * @arg TIM_EXT_CLK_SRC_TI1ED TI1 Edge Detector * @arg TIM_EXT_CLK_SRC_TI1 Filtered Timer Input 1 * @arg TIM_EXT_CLK_SRC_TI2 Filtered Timer Input 2 * @param IcPolarity specifies the TIx Polarity. * This parameter can be one of the following values: * @arg TIM_IC_POLARITY_RISING * @arg TIM_IC_POLARITY_FALLING * @param ICFilter specifies the filter value. * This parameter must be a value between 0x0 and 0xF. */ void TIM_ConfigExtTrigAsClk(TIM_Module* TIMx, uint16_t TIM_TIxExternalCLKSource, uint16_t IcPolarity, uint16_t ICFilter) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimExtClkSrc(TIM_TIxExternalCLKSource)); assert_param(IsTimIcPalaritySingleEdge(IcPolarity)); assert_param(IsTimInCapFilter(ICFilter)); /* Configure the Timer Input Clock Source */ if (TIM_TIxExternalCLKSource == TIM_EXT_CLK_SRC_TI2) { ConfigTI2(TIMx, IcPolarity, TIM_IC_SELECTION_DIRECTTI, ICFilter); } else { ConfigTI1(TIMx, IcPolarity, TIM_IC_SELECTION_DIRECTTI, ICFilter); } /* Select the Trigger source */ TIM_SelectInputTrig(TIMx, TIM_TIxExternalCLKSource); /* Select the External clock mode1 */ TIMx->SMCTRL |= TIM_SLAVE_MODE_EXT1; } /** * @brief Configures the External clock Mode1 * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_ExtTRGPrescaler The external Trigger Prescaler. * This parameter can be one of the following values: * @arg TIM_EXT_TRG_PSC_OFF ETRP Prescaler OFF. * @arg TIM_EXT_TRG_PSC_DIV2 ETRP frequency divided by 2. * @arg TIM_EXT_TRG_PSC_DIV4 ETRP frequency divided by 4. * @arg TIM_EXT_TRG_PSC_DIV8 ETRP frequency divided by 8. * @param TIM_ExtTRGPolarity The external Trigger Polarity. * This parameter can be one of the following values: * @arg TIM_EXT_TRIG_POLARITY_INVERTED active low or falling edge active. * @arg TIM_EXT_TRIG_POLARITY_NONINVERTED active high or rising edge active. * @param ExtTRGFilter External Trigger Filter. * This parameter must be a value between 0x00 and 0x0F */ void TIM_ConfigExtClkMode1(TIM_Module* TIMx, uint16_t TIM_ExtTRGPrescaler, uint16_t TIM_ExtTRGPolarity, uint16_t ExtTRGFilter) { uint16_t tmpsmcr = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimExtPreDiv(TIM_ExtTRGPrescaler)); assert_param(IsTimExtTrigPolarity(TIM_ExtTRGPolarity)); assert_param(IsTimExtTrigFilter(ExtTRGFilter)); /* Configure the ETR Clock source */ TIM_ConfigExtTrig(TIMx, TIM_ExtTRGPrescaler, TIM_ExtTRGPolarity, ExtTRGFilter); /* Get the TIMx SMCTRL register value */ tmpsmcr = TIMx->SMCTRL; /* Reset the SMS Bits */ tmpsmcr &= (uint16_t)(~((uint16_t)TIM_SMCTRL_SMSEL)); /* Select the External clock mode1 */ tmpsmcr |= TIM_SLAVE_MODE_EXT1; /* Select the Trigger selection : ETRF */ tmpsmcr &= (uint16_t)(~((uint16_t)TIM_SMCTRL_TSEL)); tmpsmcr |= TIM_TRIG_SEL_ETRF; /* Write to TIMx SMCTRL */ TIMx->SMCTRL = tmpsmcr; } /** * @brief Configures the External clock Mode2 * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_ExtTRGPrescaler The external Trigger Prescaler. * This parameter can be one of the following values: * @arg TIM_EXT_TRG_PSC_OFF ETRP Prescaler OFF. * @arg TIM_EXT_TRG_PSC_DIV2 ETRP frequency divided by 2. * @arg TIM_EXT_TRG_PSC_DIV4 ETRP frequency divided by 4. * @arg TIM_EXT_TRG_PSC_DIV8 ETRP frequency divided by 8. * @param TIM_ExtTRGPolarity The external Trigger Polarity. * This parameter can be one of the following values: * @arg TIM_EXT_TRIG_POLARITY_INVERTED active low or falling edge active. * @arg TIM_EXT_TRIG_POLARITY_NONINVERTED active high or rising edge active. * @param ExtTRGFilter External Trigger Filter. * This parameter must be a value between 0x00 and 0x0F */ void TIM_ConfigExtClkMode2(TIM_Module* TIMx, uint16_t TIM_ExtTRGPrescaler, uint16_t TIM_ExtTRGPolarity, uint16_t ExtTRGFilter) { /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimExtPreDiv(TIM_ExtTRGPrescaler)); assert_param(IsTimExtTrigPolarity(TIM_ExtTRGPolarity)); assert_param(IsTimExtTrigFilter(ExtTRGFilter)); /* Configure the ETR Clock source */ TIM_ConfigExtTrig(TIMx, TIM_ExtTRGPrescaler, TIM_ExtTRGPolarity, ExtTRGFilter); /* Enable the External clock mode2 */ TIMx->SMCTRL |= TIM_SMCTRL_EXCEN; } /** * @brief Configures the TIMx External Trigger (ETR). * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_ExtTRGPrescaler The external Trigger Prescaler. * This parameter can be one of the following values: * @arg TIM_EXT_TRG_PSC_OFF ETRP Prescaler OFF. * @arg TIM_EXT_TRG_PSC_DIV2 ETRP frequency divided by 2. * @arg TIM_EXT_TRG_PSC_DIV4 ETRP frequency divided by 4. * @arg TIM_EXT_TRG_PSC_DIV8 ETRP frequency divided by 8. * @param TIM_ExtTRGPolarity The external Trigger Polarity. * This parameter can be one of the following values: * @arg TIM_EXT_TRIG_POLARITY_INVERTED active low or falling edge active. * @arg TIM_EXT_TRIG_POLARITY_NONINVERTED active high or rising edge active. * @param ExtTRGFilter External Trigger Filter. * This parameter must be a value between 0x00 and 0x0F */ void TIM_ConfigExtTrig(TIM_Module* TIMx, uint16_t TIM_ExtTRGPrescaler, uint16_t TIM_ExtTRGPolarity, uint16_t ExtTRGFilter) { uint16_t tmpsmcr = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimExtPreDiv(TIM_ExtTRGPrescaler)); assert_param(IsTimExtTrigPolarity(TIM_ExtTRGPolarity)); assert_param(IsTimExtTrigFilter(ExtTRGFilter)); tmpsmcr = TIMx->SMCTRL; /* Reset the ETR Bits */ tmpsmcr &= SMCTRL_ETR_MASK; /* Set the Prescaler, the Filter value and the Polarity */ tmpsmcr |= (uint16_t)(TIM_ExtTRGPrescaler | (uint16_t)(TIM_ExtTRGPolarity | (uint16_t)(ExtTRGFilter << (uint16_t)8))); /* Write to TIMx SMCTRL */ TIMx->SMCTRL = tmpsmcr; } /** * @brief Configures the TIMx Prescaler. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param Prescaler specifies the Prescaler Register value * @param TIM_PSCReloadMode specifies the TIM Prescaler Reload mode * This parameter can be one of the following values: * @arg TIM_PSC_RELOAD_MODE_UPDATE The Prescaler is loaded at the update event. * @arg TIM_PSC_RELOAD_MODE_IMMEDIATE The Prescaler is loaded immediately. */ void TIM_ConfigPrescaler(TIM_Module* TIMx, uint16_t Prescaler, uint16_t TIM_PSCReloadMode) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimPscReloadMode(TIM_PSCReloadMode)); /* Set the Prescaler value */ TIMx->PSC = Prescaler; /* Set or reset the UG Bit */ TIMx->EVTGEN = TIM_PSCReloadMode; } /** * @brief Specifies the TIMx Counter Mode to be used. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param CntMode specifies the Counter Mode to be used * This parameter can be one of the following values: * @arg TIM_CNT_MODE_UP TIM Up Counting Mode * @arg TIM_CNT_MODE_DOWN TIM Down Counting Mode * @arg TIM_CNT_MODE_CENTER_ALIGN1 TIM Center Aligned Mode1 * @arg TIM_CNT_MODE_CENTER_ALIGN2 TIM Center Aligned Mode2 * @arg TIM_CNT_MODE_CENTER_ALIGN3 TIM Center Aligned Mode3 */ void TIM_ConfigCntMode(TIM_Module* TIMx, uint16_t CntMode) { uint32_t tmpcr1 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimCntMode(CntMode)); tmpcr1 = TIMx->CTRL1; /* Reset the CMS and DIR Bits */ tmpcr1 &= (uint32_t)(~((uint32_t)(TIM_CTRL1_DIR | TIM_CTRL1_CAMSEL))); /* Set the Counter Mode */ tmpcr1 |= CntMode; /* Write to TIMx CTRL1 register */ TIMx->CTRL1 = tmpcr1; } /** * @brief Selects the Input Trigger source * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param TIM_InputTriggerSource The Input Trigger source. * This parameter can be one of the following values: * @arg TIM_TRIG_SEL_IN_TR0 Internal Trigger 0 * @arg TIM_TRIG_SEL_IN_TR1 Internal Trigger 1 * @arg TIM_TRIG_SEL_IN_TR2 Internal Trigger 2 * @arg TIM_TRIG_SEL_IN_TR3 Internal Trigger 3 * @arg TIM_TRIG_SEL_TI1F_ED TI1 Edge Detector * @arg TIM_TRIG_SEL_TI1FP1 Filtered Timer Input 1 * @arg TIM_TRIG_SEL_TI2FP2 Filtered Timer Input 2 * @arg TIM_TRIG_SEL_ETRF External Trigger input */ void TIM_SelectInputTrig(TIM_Module* TIMx, uint16_t TIM_InputTriggerSource) { uint16_t tmpsmcr = 0; /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimTrigSel(TIM_InputTriggerSource)); /* Get the TIMx SMCTRL register value */ tmpsmcr = TIMx->SMCTRL; /* Reset the TS Bits */ tmpsmcr &= (uint16_t)(~((uint16_t)TIM_SMCTRL_TSEL)); /* Set the Input Trigger source */ tmpsmcr |= TIM_InputTriggerSource; /* Write to TIMx SMCTRL */ TIMx->SMCTRL = tmpsmcr; } /** * @brief Configures the TIMx Encoder Interface. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_EncoderMode specifies the TIMx Encoder Mode. * This parameter can be one of the following values: * @arg TIM_ENCODE_MODE_TI1 Counter counts on TI1FP1 edge depending on TI2FP2 level. * @arg TIM_ENCODE_MODE_TI2 Counter counts on TI2FP2 edge depending on TI1FP1 level. * @arg TIM_ENCODE_MODE_TI12 Counter counts on both TI1FP1 and TI2FP2 edges depending * on the level of the other input. * @param TIM_IC1Polarity specifies the IC1 Polarity * This parameter can be one of the following values: * @arg TIM_IC_POLARITY_FALLING IC Falling edge. * @arg TIM_IC_POLARITY_RISING IC Rising edge. * @param TIM_IC2Polarity specifies the IC2 Polarity * This parameter can be one of the following values: * @arg TIM_IC_POLARITY_FALLING IC Falling edge. * @arg TIM_IC_POLARITY_RISING IC Rising edge. */ void TIM_ConfigEncoderInterface(TIM_Module* TIMx, uint16_t TIM_EncoderMode, uint16_t TIM_IC1Polarity, uint16_t TIM_IC2Polarity) { uint16_t tmpsmcr = 0; uint16_t tmpccmr1 = 0; uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList5Module(TIMx)); assert_param(IsTimEncodeMode(TIM_EncoderMode)); assert_param(IsTimIcPalaritySingleEdge(TIM_IC1Polarity)); assert_param(IsTimIcPalaritySingleEdge(TIM_IC2Polarity)); /* Get the TIMx SMCTRL register value */ tmpsmcr = TIMx->SMCTRL; /* Get the TIMx CCMOD1 register value */ tmpccmr1 = TIMx->CCMOD1; /* Get the TIMx CCEN register value */ tmpccer = TIMx->CCEN; /* Set the encoder Mode */ tmpsmcr &= (uint16_t)(~((uint16_t)TIM_SMCTRL_SMSEL)); tmpsmcr |= TIM_EncoderMode; /* Select the Capture Compare 1 and the Capture Compare 2 as input */ tmpccmr1 &= (uint16_t)(((uint16_t) ~((uint16_t)TIM_CCMOD1_CC1SEL)) & (uint16_t)(~((uint16_t)TIM_CCMOD1_CC2SEL))); tmpccmr1 |= TIM_CCMOD1_CC1SEL_0 | TIM_CCMOD1_CC2SEL_0; /* Set the TI1 and the TI2 Polarities */ tmpccer &= (uint32_t)(((uint32_t) ~((uint32_t)TIM_CCEN_CC1P)) & ((uint32_t) ~((uint32_t)TIM_CCEN_CC2P))); tmpccer |= (uint32_t)(TIM_IC1Polarity | (uint16_t)(TIM_IC2Polarity << (uint16_t)4)); /* Write to TIMx SMCTRL */ TIMx->SMCTRL = tmpsmcr; /* Write to TIMx CCMOD1 */ TIMx->CCMOD1 = tmpccmr1; /* Write to TIMx CCEN */ TIMx->CCEN = tmpccer; } /** * @brief Forces the TIMx output 1 waveform to active or inactive level. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param TIM_ForcedAction specifies the forced Action to be set to the output waveform. * This parameter can be one of the following values: * @arg TIM_FORCED_ACTION_ACTIVE Force active level on OC1REF * @arg TIM_FORCED_ACTION_INACTIVE Force inactive level on OC1REF. */ void TIM_ConfigForcedOc1(TIM_Module* TIMx, uint16_t TIM_ForcedAction) { uint16_t tmpccmr1 = 0; /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimForceActive(TIM_ForcedAction)); tmpccmr1 = TIMx->CCMOD1; /* Reset the OC1M Bits */ tmpccmr1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_OC1M); /* Configure The Forced output Mode */ tmpccmr1 |= TIM_ForcedAction; /* Write to TIMx CCMOD1 register */ TIMx->CCMOD1 = tmpccmr1; } /** * @brief Forces the TIMx output 2 waveform to active or inactive level. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param TIM_ForcedAction specifies the forced Action to be set to the output waveform. * This parameter can be one of the following values: * @arg TIM_FORCED_ACTION_ACTIVE Force active level on OC2REF * @arg TIM_FORCED_ACTION_INACTIVE Force inactive level on OC2REF. */ void TIM_ConfigForcedOc2(TIM_Module* TIMx, uint16_t TIM_ForcedAction) { uint16_t tmpccmr1 = 0; /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimForceActive(TIM_ForcedAction)); tmpccmr1 = TIMx->CCMOD1; /* Reset the OC2M Bits */ tmpccmr1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_OC2M); /* Configure The Forced output Mode */ tmpccmr1 |= (uint16_t)(TIM_ForcedAction << 8); /* Write to TIMx CCMOD1 register */ TIMx->CCMOD1 = tmpccmr1; } /** * @brief Forces the TIMx output 3 waveform to active or inactive level. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_ForcedAction specifies the forced Action to be set to the output waveform. * This parameter can be one of the following values: * @arg TIM_FORCED_ACTION_ACTIVE Force active level on OC3REF * @arg TIM_FORCED_ACTION_INACTIVE Force inactive level on OC3REF. */ void TIM_ConfigForcedOc3(TIM_Module* TIMx, uint16_t TIM_ForcedAction) { uint16_t tmpccmr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimForceActive(TIM_ForcedAction)); tmpccmr2 = TIMx->CCMOD2; /* Reset the OC1M Bits */ tmpccmr2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_OC3MD); /* Configure The Forced output Mode */ tmpccmr2 |= TIM_ForcedAction; /* Write to TIMx CCMOD2 register */ TIMx->CCMOD2 = tmpccmr2; } /** * @brief Forces the TIMx output 4 waveform to active or inactive level. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_ForcedAction specifies the forced Action to be set to the output waveform. * This parameter can be one of the following values: * @arg TIM_FORCED_ACTION_ACTIVE Force active level on OC4REF * @arg TIM_FORCED_ACTION_INACTIVE Force inactive level on OC4REF. */ void TIM_ConfigForcedOc4(TIM_Module* TIMx, uint16_t TIM_ForcedAction) { uint16_t tmpccmr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimForceActive(TIM_ForcedAction)); tmpccmr2 = TIMx->CCMOD2; /* Reset the OC2M Bits */ tmpccmr2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_OC4MD); /* Configure The Forced output Mode */ tmpccmr2 |= (uint16_t)(TIM_ForcedAction << 8); /* Write to TIMx CCMOD2 register */ TIMx->CCMOD2 = tmpccmr2; } /** * @brief Forces the TIMx output 5 waveform to active or inactive level. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_ForcedAction specifies the forced Action to be set to the output waveform. * This parameter can be one of the following values: * @arg TIM_FORCED_ACTION_ACTIVE Force active level on OC5REF * @arg TIM_FORCED_ACTION_INACTIVE Force inactive level on OC5REF. */ void TIM_ConfigForcedOc5(TIM_Module* TIMx, uint16_t TIM_ForcedAction) { uint16_t tmpccmr3 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimForceActive(TIM_ForcedAction)); tmpccmr3 = TIMx->CCMOD3; /* Reset the OC2M Bits */ tmpccmr3 &= (uint16_t) ~((uint16_t)TIM_CCMOD3_OC5MD); /* Configure The Forced output Mode */ tmpccmr3 |= (uint16_t)(TIM_ForcedAction); /* Write to TIMx CCMOD2 register */ TIMx->CCMOD3 = tmpccmr3; } /** * @brief Forces the TIMx output 6 waveform to active or inactive level. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_ForcedAction specifies the forced Action to be set to the output waveform. * This parameter can be one of the following values: * @arg TIM_FORCED_ACTION_ACTIVE Force active level on OC6REF * @arg TIM_FORCED_ACTION_INACTIVE Force inactive level on OC6REF. */ void TIM_ConfigForcedOc6(TIM_Module* TIMx, uint16_t TIM_ForcedAction) { uint16_t tmpccmr3 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimForceActive(TIM_ForcedAction)); tmpccmr3 = TIMx->CCMOD3; /* Reset the OC2M Bits */ tmpccmr3 &= (uint16_t) ~((uint16_t)TIM_CCMOD3_OC6MD); /* Configure The Forced output Mode */ tmpccmr3 |= (uint16_t)(TIM_ForcedAction << 8); /* Write to TIMx CCMOD2 register */ TIMx->CCMOD3 = tmpccmr3; } /** * @brief Enables or disables TIMx peripheral Preload register on AR. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param Cmd new state of the TIMx peripheral Preload register * This parameter can be: ENABLE or DISABLE. */ void TIM_ConfigArPreload(TIM_Module* TIMx, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Set the AR Preload Bit */ TIMx->CTRL1 |= TIM_CTRL1_ARPEN; } else { /* Reset the AR Preload Bit */ TIMx->CTRL1 &= (uint32_t) ~((uint32_t)TIM_CTRL1_ARPEN); } } /** * @brief Selects the TIM peripheral Commutation event. * @param TIMx where x can be 1, 8 to select the TIMx peripheral * @param Cmd new state of the Commutation event. * This parameter can be: ENABLE or DISABLE. */ void TIM_SelectComEvt(TIM_Module* TIMx, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimList2Module(TIMx)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Set the COM Bit */ TIMx->CTRL2 |= TIM_CTRL2_CCUSEL; } else { /* Reset the COM Bit */ TIMx->CTRL2 &= (uint32_t) ~((uint32_t)TIM_CTRL2_CCUSEL); } } /** * @brief Selects the TIMx peripheral Capture Compare DMA source. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select * the TIM peripheral. * @param Cmd new state of the Capture Compare DMA source * This parameter can be: ENABLE or DISABLE. */ void TIM_SelectCapCmpDmaSrc(TIM_Module* TIMx, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimList4Module(TIMx)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Set the CCDS Bit */ TIMx->CTRL2 |= TIM_CTRL2_CCDSEL; } else { /* Reset the CCDS Bit */ TIMx->CTRL2 &= (uint32_t) ~((uint32_t)TIM_CTRL2_CCDSEL); } } /** * @brief Sets or Resets the TIM peripheral Capture Compare Preload Control bit. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 * to select the TIMx peripheral * @param Cmd new state of the Capture Compare Preload Control bit * This parameter can be: ENABLE or DISABLE. */ void TIM_EnableCapCmpPreloadControl(TIM_Module* TIMx, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimList5Module(TIMx)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Set the CCPC Bit */ TIMx->CTRL2 |= TIM_CTRL2_CCPCTL; } else { /* Reset the CCPC Bit */ TIMx->CTRL2 &= (uint32_t) ~((uint32_t)TIM_CTRL2_CCPCTL); } } /** * @brief Enables or disables the TIMx peripheral Preload register on CCDAT1. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param TIM_OCPreload new state of the TIMx peripheral Preload register * This parameter can be one of the following values: * @arg TIM_OC_PRE_LOAD_ENABLE * @arg TIM_OC_PRE_LOAD_DISABLE */ void TIM_ConfigOc1Preload(TIM_Module* TIMx, uint16_t TIM_OCPreload) { uint16_t tmpccmr1 = 0; /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimOcPreLoadState(TIM_OCPreload)); tmpccmr1 = TIMx->CCMOD1; /* Reset the OC1PE Bit */ tmpccmr1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_OC1PEN); /* Enable or Disable the Output Compare Preload feature */ tmpccmr1 |= TIM_OCPreload; /* Write to TIMx CCMOD1 register */ TIMx->CCMOD1 = tmpccmr1; } /** * @brief Enables or disables the TIMx peripheral Preload register on CCDAT2. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select * the TIM peripheral. * @param TIM_OCPreload new state of the TIMx peripheral Preload register * This parameter can be one of the following values: * @arg TIM_OC_PRE_LOAD_ENABLE * @arg TIM_OC_PRE_LOAD_DISABLE */ void TIM_ConfigOc2Preload(TIM_Module* TIMx, uint16_t TIM_OCPreload) { uint16_t tmpccmr1 = 0; /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimOcPreLoadState(TIM_OCPreload)); tmpccmr1 = TIMx->CCMOD1; /* Reset the OC2PE Bit */ tmpccmr1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_OC2PEN); /* Enable or Disable the Output Compare Preload feature */ tmpccmr1 |= (uint16_t)(TIM_OCPreload << 8); /* Write to TIMx CCMOD1 register */ TIMx->CCMOD1 = tmpccmr1; } /** * @brief Enables or disables the TIMx peripheral Preload register on CCDAT3. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCPreload new state of the TIMx peripheral Preload register * This parameter can be one of the following values: * @arg TIM_OC_PRE_LOAD_ENABLE * @arg TIM_OC_PRE_LOAD_DISABLE */ void TIM_ConfigOc3Preload(TIM_Module* TIMx, uint16_t TIM_OCPreload) { uint16_t tmpccmr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcPreLoadState(TIM_OCPreload)); tmpccmr2 = TIMx->CCMOD2; /* Reset the OC3PE Bit */ tmpccmr2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_OC3PEN); /* Enable or Disable the Output Compare Preload feature */ tmpccmr2 |= TIM_OCPreload; /* Write to TIMx CCMOD2 register */ TIMx->CCMOD2 = tmpccmr2; } /** * @brief Enables or disables the TIMx peripheral Preload register on CCDAT4. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCPreload new state of the TIMx peripheral Preload register * This parameter can be one of the following values: * @arg TIM_OC_PRE_LOAD_ENABLE * @arg TIM_OC_PRE_LOAD_DISABLE */ void TIM_ConfigOc4Preload(TIM_Module* TIMx, uint16_t TIM_OCPreload) { uint16_t tmpccmr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcPreLoadState(TIM_OCPreload)); tmpccmr2 = TIMx->CCMOD2; /* Reset the OC4PE Bit */ tmpccmr2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_OC4PEN); /* Enable or Disable the Output Compare Preload feature */ tmpccmr2 |= (uint16_t)(TIM_OCPreload << 8); /* Write to TIMx CCMOD2 register */ TIMx->CCMOD2 = tmpccmr2; } /** * @brief Enables or disables the TIMx peripheral Preload register on CCDAT5. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_OCPreload new state of the TIMx peripheral Preload register * This parameter can be one of the following values: * @arg TIM_OC_PRE_LOAD_ENABLE * @arg TIM_OC_PRE_LOAD_DISABLE */ void TIM_ConfigOc5Preload(TIM_Module* TIMx, uint16_t TIM_OCPreload) { uint16_t tmpccmr3 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcPreLoadState(TIM_OCPreload)); tmpccmr3 = TIMx->CCMOD3; /* Reset the OC5PE Bit */ tmpccmr3 &= (uint16_t) ~((uint16_t)TIM_CCMOD3_OC5PEN); /* Enable or Disable the Output Compare Preload feature */ tmpccmr3 |= (uint16_t)(TIM_OCPreload); /* Write to TIMx CCMOD3 register */ TIMx->CCMOD3 = tmpccmr3; } /** * @brief Enables or disables the TIMx peripheral Preload register on CCDAT6. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_OCPreload new state of the TIMx peripheral Preload register * This parameter can be one of the following values: * @arg TIM_OC_PRE_LOAD_ENABLE * @arg TIM_OC_PRE_LOAD_DISABLE */ void TIM_ConfigOc6Preload(TIM_Module* TIMx, uint16_t TIM_OCPreload) { uint16_t tmpccmr3 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcPreLoadState(TIM_OCPreload)); tmpccmr3 = TIMx->CCMOD3; /* Reset the OC6PE Bit */ tmpccmr3 &= (uint16_t) ~((uint16_t)TIM_CCMOD3_OC6PEN); /* Enable or Disable the Output Compare Preload feature */ tmpccmr3 |= (uint16_t)(TIM_OCPreload << 8); /* Write to TIMx CCMOD3 register */ TIMx->CCMOD3 = tmpccmr3; } /** * @brief Configures the TIMx Output Compare 1 Fast feature. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param TIM_OCFast new state of the Output Compare Fast Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_FAST_ENABLE TIM output compare fast enable * @arg TIM_OC_FAST_DISABLE TIM output compare fast disable */ void TIM_ConfigOc1Fast(TIM_Module* TIMx, uint16_t TIM_OCFast) { uint16_t tmpccmr1 = 0; /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimOcFastState(TIM_OCFast)); /* Get the TIMx CCMOD1 register value */ tmpccmr1 = TIMx->CCMOD1; /* Reset the OC1FE Bit */ tmpccmr1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_OC1FEN); /* Enable or Disable the Output Compare Fast Bit */ tmpccmr1 |= TIM_OCFast; /* Write to TIMx CCMOD1 */ TIMx->CCMOD1 = tmpccmr1; } /** * @brief Configures the TIMx Output Compare 2 Fast feature. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select * the TIM peripheral. * @param TIM_OCFast new state of the Output Compare Fast Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_FAST_ENABLE TIM output compare fast enable * @arg TIM_OC_FAST_DISABLE TIM output compare fast disable */ void TIM_ConfigOc2Fast(TIM_Module* TIMx, uint16_t TIM_OCFast) { uint16_t tmpccmr1 = 0; /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimOcFastState(TIM_OCFast)); /* Get the TIMx CCMOD1 register value */ tmpccmr1 = TIMx->CCMOD1; /* Reset the OC2FE Bit */ tmpccmr1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_OC2FEN); /* Enable or Disable the Output Compare Fast Bit */ tmpccmr1 |= (uint16_t)(TIM_OCFast << 8); /* Write to TIMx CCMOD1 */ TIMx->CCMOD1 = tmpccmr1; } /** * @brief Configures the TIMx Output Compare 3 Fast feature. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCFast new state of the Output Compare Fast Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_FAST_ENABLE TIM output compare fast enable * @arg TIM_OC_FAST_DISABLE TIM output compare fast disable */ void TIM_ConfigOc3Fast(TIM_Module* TIMx, uint16_t TIM_OCFast) { uint16_t tmpccmr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcFastState(TIM_OCFast)); /* Get the TIMx CCMOD2 register value */ tmpccmr2 = TIMx->CCMOD2; /* Reset the OC3FE Bit */ tmpccmr2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_OC3FEN); /* Enable or Disable the Output Compare Fast Bit */ tmpccmr2 |= TIM_OCFast; /* Write to TIMx CCMOD2 */ TIMx->CCMOD2 = tmpccmr2; } /** * @brief Configures the TIMx Output Compare 4 Fast feature. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCFast new state of the Output Compare Fast Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_FAST_ENABLE TIM output compare fast enable * @arg TIM_OC_FAST_DISABLE TIM output compare fast disable */ void TIM_ConfigOc4Fast(TIM_Module* TIMx, uint16_t TIM_OCFast) { uint16_t tmpccmr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcFastState(TIM_OCFast)); /* Get the TIMx CCMOD2 register value */ tmpccmr2 = TIMx->CCMOD2; /* Reset the OC4FE Bit */ tmpccmr2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_OC4FEN); /* Enable or Disable the Output Compare Fast Bit */ tmpccmr2 |= (uint16_t)(TIM_OCFast << 8); /* Write to TIMx CCMOD2 */ TIMx->CCMOD2 = tmpccmr2; } /** * @brief Configures the TIMx Output Compare 5 Fast feature. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_OCFast new state of the Output Compare Fast Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_FAST_ENABLE TIM output compare fast enable * @arg TIM_OC_FAST_DISABLE TIM output compare fast disable */ void TIM_ConfigOc5Fast(TIM_Module* TIMx, uint16_t TIM_OCFast) { uint16_t tmpccmr3 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcFastState(TIM_OCFast)); /* Get the TIMx CCMOD2 register value */ tmpccmr3 = TIMx->CCMOD3; /* Reset the OC4FE Bit */ tmpccmr3 &= (uint16_t) ~((uint16_t)TIM_CCMOD3_OC5FEN); /* Enable or Disable the Output Compare Fast Bit */ tmpccmr3 |= (uint16_t)(TIM_OCFast); /* Write to TIMx CCMOD3 */ TIMx->CCMOD3 = tmpccmr3; } /** * @brief Configures the TIMx Output Compare 6 Fast feature. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_OCFast new state of the Output Compare Fast Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_FAST_ENABLE TIM output compare fast enable * @arg TIM_OC_FAST_DISABLE TIM output compare fast disable */ void TIM_ConfigOc6Fast(TIM_Module* TIMx, uint16_t TIM_OCFast) { uint16_t tmpccmr3 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcFastState(TIM_OCFast)); /* Get the TIMx CCMOD2 register value */ tmpccmr3 = TIMx->CCMOD3; /* Reset the OC4FE Bit */ tmpccmr3 &= (uint16_t) ~((uint16_t)TIM_CCMOD3_OC6FEN); /* Enable or Disable the Output Compare Fast Bit */ tmpccmr3 |= (uint16_t)(TIM_OCFast << 8); /* Write to TIMx CCMOD3 */ TIMx->CCMOD3 = tmpccmr3; } /** * @brief Clears or safeguards the OCREF1 signal on an external event * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCClear new state of the Output Compare Clear Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_CLR_ENABLE TIM Output clear enable * @arg TIM_OC_CLR_DISABLE TIM Output clear disable */ void TIM_ClrOc1Ref(TIM_Module* TIMx, uint16_t TIM_OCClear) { uint16_t tmpccmr1 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcClrState(TIM_OCClear)); tmpccmr1 = TIMx->CCMOD1; /* Reset the OC1CE Bit */ tmpccmr1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_OC1CEN); /* Enable or Disable the Output Compare Clear Bit */ tmpccmr1 |= TIM_OCClear; /* Write to TIMx CCMOD1 register */ TIMx->CCMOD1 = tmpccmr1; } /** * @brief Clears or safeguards the OCREF2 signal on an external event * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCClear new state of the Output Compare Clear Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_CLR_ENABLE TIM Output clear enable * @arg TIM_OC_CLR_DISABLE TIM Output clear disable */ void TIM_ClrOc2Ref(TIM_Module* TIMx, uint16_t TIM_OCClear) { uint16_t tmpccmr1 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcClrState(TIM_OCClear)); tmpccmr1 = TIMx->CCMOD1; /* Reset the OC2CE Bit */ tmpccmr1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_OC2CEN); /* Enable or Disable the Output Compare Clear Bit */ tmpccmr1 |= (uint16_t)(TIM_OCClear << 8); /* Write to TIMx CCMOD1 register */ TIMx->CCMOD1 = tmpccmr1; } /** * @brief Clears or safeguards the OCREF3 signal on an external event * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCClear new state of the Output Compare Clear Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_CLR_ENABLE TIM Output clear enable * @arg TIM_OC_CLR_DISABLE TIM Output clear disable */ void TIM_ClrOc3Ref(TIM_Module* TIMx, uint16_t TIM_OCClear) { uint16_t tmpccmr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcClrState(TIM_OCClear)); tmpccmr2 = TIMx->CCMOD2; /* Reset the OC3CE Bit */ tmpccmr2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_OC3CEN); /* Enable or Disable the Output Compare Clear Bit */ tmpccmr2 |= TIM_OCClear; /* Write to TIMx CCMOD2 register */ TIMx->CCMOD2 = tmpccmr2; } /** * @brief Clears or safeguards the OCREF4 signal on an external event * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_OCClear new state of the Output Compare Clear Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_CLR_ENABLE TIM Output clear enable * @arg TIM_OC_CLR_DISABLE TIM Output clear disable */ void TIM_ClrOc4Ref(TIM_Module* TIMx, uint16_t TIM_OCClear) { uint16_t tmpccmr2 = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcClrState(TIM_OCClear)); tmpccmr2 = TIMx->CCMOD2; /* Reset the OC4CE Bit */ tmpccmr2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_OC4CEN); /* Enable or Disable the Output Compare Clear Bit */ tmpccmr2 |= (uint16_t)(TIM_OCClear << 8); /* Write to TIMx CCMOD2 register */ TIMx->CCMOD2 = tmpccmr2; } /** * @brief Clears or safeguards the OCREF5 signal on an external event * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_OCClear new state of the Output Compare Clear Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_CLR_ENABLE TIM Output clear enable * @arg TIM_OC_CLR_DISABLE TIM Output clear disable */ void TIM_ClrOc5Ref(TIM_Module* TIMx, uint16_t TIM_OCClear) { uint16_t tmpccmr3 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcClrState(TIM_OCClear)); tmpccmr3 = TIMx->CCMOD3; /* Reset the OC4CE Bit */ tmpccmr3 &= (uint16_t) ~((uint16_t)TIM_CCMOD3_OC5CEN); /* Enable or Disable the Output Compare Clear Bit */ tmpccmr3 |= (uint16_t)(TIM_OCClear); /* Write to TIMx CCMOD3 register */ TIMx->CCMOD3 = tmpccmr3; } /** * @brief Clears or safeguards the OCREF6 signal on an external event * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param TIM_OCClear new state of the Output Compare Clear Enable Bit. * This parameter can be one of the following values: * @arg TIM_OC_CLR_ENABLE TIM Output clear enable * @arg TIM_OC_CLR_DISABLE TIM Output clear disable */ void TIM_ClrOc6Ref(TIM_Module* TIMx, uint16_t TIM_OCClear) { uint16_t tmpccmr3 = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcClrState(TIM_OCClear)); tmpccmr3 = TIMx->CCMOD3; /* Reset the OC4CE Bit */ tmpccmr3 &= (uint16_t) ~((uint16_t)TIM_CCMOD3_OC6CEN); /* Enable or Disable the Output Compare Clear Bit */ tmpccmr3 |= (uint16_t)(TIM_OCClear << 8); /* Write to TIMx CCMOD3 register */ TIMx->CCMOD3 = tmpccmr3; } /** * @brief Configures the TIMx channel 1 polarity. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param OcPolarity specifies the OC1 Polarity * This parameter can be one of the following values: * @arg TIM_OC_POLARITY_HIGH Output Compare active high * @arg TIM_OC_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc1Polarity(TIM_Module* TIMx, uint16_t OcPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimOcPolarity(OcPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC1P Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC1P); tmpccer |= OcPolarity; /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Configures the TIMx Channel 1N polarity. * @param TIMx where x can be 1, 8 to select the TIM peripheral. * @param OcNPolarity specifies the OC1N Polarity * This parameter can be one of the following values: * @arg TIM_OCN_POLARITY_HIGH Output Compare active high * @arg TIM_OCN_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc1NPolarity(TIM_Module* TIMx, uint16_t OcNPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList2Module(TIMx)); assert_param(IsTimOcnPolarity(OcNPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC1NP Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC1NP); tmpccer |= OcNPolarity; /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Configures the TIMx channel 2 polarity. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param OcPolarity specifies the OC2 Polarity * This parameter can be one of the following values: * @arg TIM_OC_POLARITY_HIGH Output Compare active high * @arg TIM_OC_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc2Polarity(TIM_Module* TIMx, uint16_t OcPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimOcPolarity(OcPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC2P Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC2P); tmpccer |= (uint32_t)(OcPolarity << 4); /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Configures the TIMx Channel 2N polarity. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param OcNPolarity specifies the OC2N Polarity * This parameter can be one of the following values: * @arg TIM_OCN_POLARITY_HIGH Output Compare active high * @arg TIM_OCN_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc2NPolarity(TIM_Module* TIMx, uint16_t OcNPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcnPolarity(OcNPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC2NP Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC2NP); tmpccer |= (uint32_t)(OcNPolarity << 4); /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Configures the TIMx channel 3 polarity. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param OcPolarity specifies the OC3 Polarity * This parameter can be one of the following values: * @arg TIM_OC_POLARITY_HIGH Output Compare active high * @arg TIM_OC_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc3Polarity(TIM_Module* TIMx, uint16_t OcPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcPolarity(OcPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC3P Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC3P); tmpccer |= (uint32_t)(OcPolarity << 8); /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Configures the TIMx Channel 3N polarity. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param OcNPolarity specifies the OC3N Polarity * This parameter can be one of the following values: * @arg TIM_OCN_POLARITY_HIGH Output Compare active high * @arg TIM_OCN_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc3NPolarity(TIM_Module* TIMx, uint16_t OcNPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcnPolarity(OcNPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC3NP Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC3NP); tmpccer |= (uint32_t)(OcNPolarity << 8); /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Configures the TIMx channel 4 polarity. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param OcPolarity specifies the OC4 Polarity * This parameter can be one of the following values: * @arg TIM_OC_POLARITY_HIGH Output Compare active high * @arg TIM_OC_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc4Polarity(TIM_Module* TIMx, uint16_t OcPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimOcPolarity(OcPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC4P Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC4P); tmpccer |= (uint32_t)(OcPolarity << 12); /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Configures the TIMx channel 5 polarity. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param OcPolarity specifies the OC5 Polarity * This parameter can be one of the following values: * @arg TIM_OC_POLARITY_HIGH Output Compare active high * @arg TIM_OC_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc5Polarity(TIM_Module* TIMx, uint16_t OcPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcPolarity(OcPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC5P Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC5P); tmpccer |= (uint32_t)(OcPolarity << 16); /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Configures the TIMx channel 6 polarity. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param OcPolarity specifies the OC6 Polarity * This parameter can be one of the following values: * @arg TIM_OC_POLARITY_HIGH Output Compare active high * @arg TIM_OC_POLARITY_LOW Output Compare active low */ void TIM_ConfigOc6Polarity(TIM_Module* TIMx, uint16_t OcPolarity) { uint32_t tmpccer = 0; /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); assert_param(IsTimOcPolarity(OcPolarity)); tmpccer = TIMx->CCEN; /* Set or Reset the CC6P Bit */ tmpccer &= (uint32_t) ~((uint32_t)TIM_CCEN_CC6P); tmpccer |= (uint32_t)(OcPolarity << 20); /* Write to TIMx CCEN register */ TIMx->CCEN = tmpccer; } /** * @brief Enables or disables the TIM Capture Compare Channel x. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param Channel specifies the TIM Channel * This parameter can be one of the following values: * @arg TIM_CH_1 TIM Channel 1 * @arg TIM_CH_2 TIM Channel 2 * @arg TIM_CH_3 TIM Channel 3 * @arg TIM_CH_4 TIM Channel 4 * @param TIM_CCx specifies the TIM Channel CCxE bit new state. * This parameter can be: TIM_CAP_CMP_ENABLE or TIM_CAP_CMP_DISABLE. */ void TIM_EnableCapCmpCh(TIM_Module* TIMx, uint16_t Channel, uint32_t TIM_CCx) { uint16_t tmp = 0; /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimCh(Channel)); assert_param(IsTimCapCmpState(TIM_CCx)); tmp = CAPCMPEN_CCE_SET << Channel; /* Reset the CCxE Bit */ TIMx->CCEN &= (uint32_t)~tmp; /* Set or reset the CCxE Bit */ TIMx->CCEN |= (uint32_t)(TIM_CCx << Channel); } /** * @brief Enables or disables the TIM Capture Compare Channel xN. * @param TIMx where x can be 1, 8 to select the TIM peripheral. * @param Channel specifies the TIM Channel * This parameter can be one of the following values: * @arg TIM_CH_1 TIM Channel 1 * @arg TIM_CH_2 TIM Channel 2 * @arg TIM_CH_3 TIM Channel 3 * @param TIM_CCxN specifies the TIM Channel CCxNE bit new state. * This parameter can be: TIM_CAP_CMP_N_ENABLE or TIM_CAP_CMP_N_DISABLE. */ void TIM_EnableCapCmpChN(TIM_Module* TIMx, uint16_t Channel, uint32_t TIM_CCxN) { uint16_t tmp = 0; /* Check the parameters */ assert_param(IsTimList2Module(TIMx)); assert_param(IsTimComplementaryCh(Channel)); assert_param(IsTimCapCmpNState(TIM_CCxN)); tmp = CAPCMPEN_CCNE_SET << Channel; /* Reset the CCxNE Bit */ TIMx->CCEN &= (uint32_t)~tmp; /* Set or reset the CCxNE Bit */ TIMx->CCEN |= (uint32_t)(TIM_CCxN << Channel); } /** * @brief Selects the TIM Output Compare Mode. * @note This function disables the selected channel before changing the Output * Compare Mode. * User has to enable this channel using TIM_EnableCapCmpCh and TIM_EnableCapCmpChN functions. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param Channel specifies the TIM Channel * This parameter can be one of the following values: * @arg TIM_CH_1 TIM Channel 1 * @arg TIM_CH_2 TIM Channel 2 * @arg TIM_CH_3 TIM Channel 3 * @arg TIM_CH_4 TIM Channel 4 * @param OcMode specifies the TIM Output Compare Mode. * This parameter can be one of the following values: * @arg TIM_OCMODE_TIMING * @arg TIM_OCMODE_ACTIVE * @arg TIM_OCMODE_TOGGLE * @arg TIM_OCMODE_PWM1 * @arg TIM_OCMODE_PWM2 * @arg TIM_FORCED_ACTION_ACTIVE * @arg TIM_FORCED_ACTION_INACTIVE */ void TIM_SelectOcMode(TIM_Module* TIMx, uint16_t Channel, uint16_t OcMode) { uint32_t tmp = 0; uint16_t tmp1 = 0; /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimCh(Channel)); assert_param(IsTimOc(OcMode)); tmp = (uint32_t)TIMx; tmp += CAPCMPMOD_OFFSET; tmp1 = CAPCMPEN_CCE_SET << (uint16_t)Channel; /* Disable the Channel: Reset the CCxE Bit */ TIMx->CCEN &= (uint16_t)~tmp1; if ((Channel == TIM_CH_1) || (Channel == TIM_CH_3)) { tmp += (Channel >> 1); /* Reset the OCxM bits in the CCMRx register */ *(__IO uint32_t*)tmp &= (uint32_t) ~((uint32_t)TIM_CCMOD1_OC1M); /* Configure the OCxM bits in the CCMRx register */ *(__IO uint32_t*)tmp |= OcMode; } else { tmp += (uint16_t)(Channel - (uint16_t)4) >> (uint16_t)1; /* Reset the OCxM bits in the CCMRx register */ *(__IO uint32_t*)tmp &= (uint32_t) ~((uint32_t)TIM_CCMOD1_OC2M); /* Configure the OCxM bits in the CCMRx register */ *(__IO uint32_t*)tmp |= (uint16_t)(OcMode << 8); } } /** * @brief Enables or Disables the TIMx Update event. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param Cmd new state of the TIMx UDIS bit * This parameter can be: ENABLE or DISABLE. */ void TIM_EnableUpdateEvt(TIM_Module* TIMx, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Set the Update Disable Bit */ TIMx->CTRL1 |= TIM_CTRL1_UPDIS; } else { /* Reset the Update Disable Bit */ TIMx->CTRL1 &= (uint32_t) ~((uint32_t)TIM_CTRL1_UPDIS); } } /** * @brief Configures the TIMx Update Request Interrupt source. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param TIM_UpdateSource specifies the Update source. * This parameter can be one of the following values: * @arg TIM_UPDATE_SRC_REGULAr Source of update is the counter overflow/underflow or the setting of UG bit, or an update generation through the slave mode controller. * @arg TIM_UPDATE_SRC_GLOBAL Source of update is counter overflow/underflow. */ void TIM_ConfigUpdateRequestIntSrc(TIM_Module* TIMx, uint16_t TIM_UpdateSource) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimUpdateSrc(TIM_UpdateSource)); if (TIM_UpdateSource != TIM_UPDATE_SRC_GLOBAL) { /* Set the URS Bit */ TIMx->CTRL1 |= TIM_CTRL1_UPRS; } else { /* Reset the URS Bit */ TIMx->CTRL1 &= (uint32_t) ~((uint32_t)TIM_CTRL1_UPRS); } } /** * @brief Enables or disables the TIMx's Hall sensor interface. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param Cmd new state of the TIMx Hall sensor interface. * This parameter can be: ENABLE or DISABLE. */ void TIM_SelectHallSensor(TIM_Module* TIMx, FunctionalState Cmd) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IS_FUNCTIONAL_STATE(Cmd)); if (Cmd != DISABLE) { /* Set the TI1S Bit */ TIMx->CTRL2 |= TIM_CTRL2_TI1SEL; } else { /* Reset the TI1S Bit */ TIMx->CTRL2 &= (uint32_t) ~((uint32_t)TIM_CTRL2_TI1SEL); } } /** * @brief Selects the TIMx's One Pulse Mode. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param TIM_OPMode specifies the OPM Mode to be used. * This parameter can be one of the following values: * @arg TIM_OPMODE_SINGLE * @arg TIM_OPMODE_REPET */ void TIM_SelectOnePulseMode(TIM_Module* TIMx, uint16_t TIM_OPMode) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimOpMOde(TIM_OPMode)); /* Reset the OPM Bit */ TIMx->CTRL1 &= (uint32_t) ~((uint32_t)TIM_CTRL1_ONEPM); /* Configure the OPM Mode */ TIMx->CTRL1 |= TIM_OPMode; } /** * @brief Selects the TIMx Trigger Output Mode. * @param TIMx where x can be 1, 2, 3, 4, 5, 6, 7, 8 to select the TIM peripheral. * @param TIM_TRGOSource specifies the Trigger Output source. * This paramter can be one of the following values: * * - For all TIMx * @arg TIM_TRGO_SRC_RESET The UG bit in the TIM_EVTGEN register is used as the trigger output (TRGO). * @arg TIM_TRGO_SRC_ENABLE The Counter Enable CEN is used as the trigger output (TRGO). * @arg TIM_TRGO_SRC_UPDATE The update event is selected as the trigger output (TRGO). * * - For all TIMx except TIM6 and TIM7 * @arg TIM_TRGO_SRC_OC1 The trigger output sends a positive pulse when the CC1IF flag * is to be set, as soon as a capture or compare match occurs (TRGO). * @arg TIM_TRGO_SRC_OC1REF OC1REF signal is used as the trigger output (TRGO). * @arg TIM_TRGO_SRC_OC2REF OC2REF signal is used as the trigger output (TRGO). * @arg TIM_TRGO_SRC_OC3REF OC3REF signal is used as the trigger output (TRGO). * @arg TIM_TRGO_SRC_OC4REF OC4REF signal is used as the trigger output (TRGO). * */ void TIM_SelectOutputTrig(TIM_Module* TIMx, uint16_t TIM_TRGOSource) { /* Check the parameters */ assert_param(IsTimList7Module(TIMx)); assert_param(IsTimTrgoSrc(TIM_TRGOSource)); /* Reset the MMS Bits */ TIMx->CTRL2 &= (uint32_t) ~((uint32_t)TIM_CTRL2_MMSEL); /* Select the TRGO source */ TIMx->CTRL2 |= TIM_TRGOSource; } /** * @brief Selects the TIMx Slave Mode. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param TIM_SlaveMode specifies the Timer Slave Mode. * This parameter can be one of the following values: * @arg TIM_SLAVE_MODE_RESET Rising edge of the selected trigger signal (TRGI) re-initializes * the counter and triggers an update of the registers. * @arg TIM_SLAVE_MODE_GATED The counter clock is enabled when the trigger signal (TRGI) is high. * @arg TIM_SLAVE_MODE_TRIG The counter starts at a rising edge of the trigger TRGI. * @arg TIM_SLAVE_MODE_EXT1 Rising edges of the selected trigger (TRGI) clock the counter. */ void TIM_SelectSlaveMode(TIM_Module* TIMx, uint16_t TIM_SlaveMode) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimSlaveMode(TIM_SlaveMode)); /* Reset the SMS Bits */ TIMx->SMCTRL &= (uint16_t) ~((uint16_t)TIM_SMCTRL_SMSEL); /* Select the Slave Mode */ TIMx->SMCTRL |= TIM_SlaveMode; } /** * @brief Sets or Resets the TIMx Master/Slave Mode. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param TIM_MasterSlaveMode specifies the Timer Master Slave Mode. * This parameter can be one of the following values: * @arg TIM_MASTER_SLAVE_MODE_ENABLE synchronization between the current timer * and its slaves (through TRGO). * @arg TIM_MASTER_SLAVE_MODE_DISABLE No action */ void TIM_SelectMasterSlaveMode(TIM_Module* TIMx, uint16_t TIM_MasterSlaveMode) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimMasterSlaveMode(TIM_MasterSlaveMode)); /* Reset the MSM Bit */ TIMx->SMCTRL &= (uint16_t) ~((uint16_t)TIM_SMCTRL_MSMD); /* Set or Reset the MSM Bit */ TIMx->SMCTRL |= TIM_MasterSlaveMode; } /** * @brief Sets the TIMx Counter Register value * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param Counter specifies the Counter register new value. */ void TIM_SetCnt(TIM_Module* TIMx, uint16_t Counter) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); /* Set the Counter Register value */ TIMx->CNT = Counter; } /** * @brief Sets the TIMx Autoreload Register value * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param Autoreload specifies the Autoreload register new value. */ void TIM_SetAutoReload(TIM_Module* TIMx, uint16_t Autoreload) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); /* Set the Autoreload Register value */ TIMx->AR = Autoreload; } /** * @brief Sets the TIMx Capture Compare1 Register value * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param Compare1 specifies the Capture Compare1 register new value. */ void TIM_SetCmp1(TIM_Module* TIMx, uint16_t Compare1) { /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); /* Set the Capture Compare1 Register value */ TIMx->CCDAT1 = Compare1; } /** * @brief Sets the TIMx Capture Compare2 Register value * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param Compare2 specifies the Capture Compare2 register new value. */ void TIM_SetCmp2(TIM_Module* TIMx, uint16_t Compare2) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); /* Set the Capture Compare2 Register value */ TIMx->CCDAT2 = Compare2; } /** * @brief Sets the TIMx Capture Compare3 Register value * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param Compare3 specifies the Capture Compare3 register new value. */ void TIM_SetCmp3(TIM_Module* TIMx, uint16_t Compare3) { /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); /* Set the Capture Compare3 Register value */ TIMx->CCDAT3 = Compare3; } /** * @brief Sets the TIMx Capture Compare4 Register value * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param Compare4 specifies the Capture Compare4 register new value. */ void TIM_SetCmp4(TIM_Module* TIMx, uint16_t Compare4) { /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); /* Set the Capture Compare4 Register value */ TIMx->CCDAT4 = Compare4; } /** * @brief Sets the TIMx Capture Compare5 Register value * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param Compare5 specifies the Capture Compare5 register new value. */ void TIM_SetCmp5(TIM_Module* TIMx, uint16_t Compare5) { /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); /* Set the Capture Compare4 Register value */ TIMx->CCDAT5 = Compare5; } /** * @brief Sets the TIMx Capture Compare4 Register value * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @param Compare6 specifies the Capture Compare6 register new value. */ void TIM_SetCmp6(TIM_Module* TIMx, uint16_t Compare6) { /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); /* Set the Capture Compare4 Register value */ TIMx->CCDAT6 = Compare6; } /** * @brief Sets the TIMx Input Capture 1 prescaler. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param TIM_ICPSC specifies the Input Capture1 prescaler new value. * This parameter can be one of the following values: * @arg TIM_IC_PSC_DIV1 no prescaler * @arg TIM_IC_PSC_DIV2 capture is done once every 2 events * @arg TIM_IC_PSC_DIV4 capture is done once every 4 events * @arg TIM_IC_PSC_DIV8 capture is done once every 8 events */ void TIM_SetInCap1Prescaler(TIM_Module* TIMx, uint16_t TIM_ICPSC) { /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimIcPrescaler(TIM_ICPSC)); /* Reset the IC1PSC Bits */ TIMx->CCMOD1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_IC1PSC); /* Set the IC1PSC value */ TIMx->CCMOD1 |= TIM_ICPSC; } /** * @brief Sets the TIMx Input Capture 2 prescaler. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param TIM_ICPSC specifies the Input Capture2 prescaler new value. * This parameter can be one of the following values: * @arg TIM_IC_PSC_DIV1 no prescaler * @arg TIM_IC_PSC_DIV2 capture is done once every 2 events * @arg TIM_IC_PSC_DIV4 capture is done once every 4 events * @arg TIM_IC_PSC_DIV8 capture is done once every 8 events */ void TIM_SetInCap2Prescaler(TIM_Module* TIMx, uint16_t TIM_ICPSC) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); assert_param(IsTimIcPrescaler(TIM_ICPSC)); /* Reset the IC2PSC Bits */ TIMx->CCMOD1 &= (uint16_t) ~((uint16_t)TIM_CCMOD1_IC2PSC); /* Set the IC2PSC value */ TIMx->CCMOD1 |= (uint16_t)(TIM_ICPSC << 8); } /** * @brief Sets the TIMx Input Capture 3 prescaler. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_ICPSC specifies the Input Capture3 prescaler new value. * This parameter can be one of the following values: * @arg TIM_IC_PSC_DIV1 no prescaler * @arg TIM_IC_PSC_DIV2 capture is done once every 2 events * @arg TIM_IC_PSC_DIV4 capture is done once every 4 events * @arg TIM_IC_PSC_DIV8 capture is done once every 8 events */ void TIM_SetInCap3Prescaler(TIM_Module* TIMx, uint16_t TIM_ICPSC) { /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimIcPrescaler(TIM_ICPSC)); /* Reset the IC3PSC Bits */ TIMx->CCMOD2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_IC3PSC); /* Set the IC3PSC value */ TIMx->CCMOD2 |= TIM_ICPSC; } /** * @brief Sets the TIMx Input Capture 4 prescaler. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param TIM_ICPSC specifies the Input Capture4 prescaler new value. * This parameter can be one of the following values: * @arg TIM_IC_PSC_DIV1 no prescaler * @arg TIM_IC_PSC_DIV2 capture is done once every 2 events * @arg TIM_IC_PSC_DIV4 capture is done once every 4 events * @arg TIM_IC_PSC_DIV8 capture is done once every 8 events */ void TIM_SetInCap4Prescaler(TIM_Module* TIMx, uint16_t TIM_ICPSC) { /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); assert_param(IsTimIcPrescaler(TIM_ICPSC)); /* Reset the IC4PSC Bits */ TIMx->CCMOD2 &= (uint16_t) ~((uint16_t)TIM_CCMOD2_IC4PSC); /* Set the IC4PSC value */ TIMx->CCMOD2 |= (uint16_t)(TIM_ICPSC << 8); } /** * @brief Sets the TIMx Clock Division value. * @param TIMx where x can be 1 to 8 except 6 and 7 to select * the TIM peripheral. * @param TIM_CKD specifies the clock division value. * This parameter can be one of the following value: * @arg TIM_CLK_DIV1 TDTS = Tck_tim * @arg TIM_CLK_DIV2 TDTS = 2*Tck_tim * @arg TIM_CLK_DIV4 TDTS = 4*Tck_tim */ void TIM_SetClkDiv(TIM_Module* TIMx, uint16_t TIM_CKD) { /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); assert_param(IsTimClkDiv(TIM_CKD)); /* Reset the CKD Bits */ TIMx->CTRL1 &= (uint32_t) ~((uint32_t)TIM_CTRL1_CLKD); /* Set the CKD value */ TIMx->CTRL1 |= TIM_CKD; } /** * @brief Gets the TIMx Input Capture 1 value. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @return Capture Compare 1 Register value. */ uint16_t TIM_GetCap1(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimList8Module(TIMx)); /* Get the Capture 1 Register value */ return TIMx->CCDAT1; } /** * @brief Gets the TIMx Input Capture 2 value. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @return Capture Compare 2 Register value. */ uint16_t TIM_GetCap2(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimList6Module(TIMx)); /* Get the Capture 2 Register value */ return TIMx->CCDAT2; } /** * @brief Gets the TIMx Input Capture 3 value. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @return Capture Compare 3 Register value. */ uint16_t TIM_GetCap3(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); /* Get the Capture 3 Register value */ return TIMx->CCDAT3; } /** * @brief Gets the TIMx Input Capture 4 value. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @return Capture Compare 4 Register value. */ uint16_t TIM_GetCap4(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); /* Get the Capture 4 Register value */ return TIMx->CCDAT4; } /** * @brief Gets the TIMx Input Capture 5 value. * @param TIMx where x can be 1 8 to select the TIM peripheral. * @return Capture Compare 5 Register value. */ uint16_t TIM_GetCap5(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); /* Get the Capture 5 Register value */ return TIMx->CCDAT5; } /** * @brief Gets the TIMx Input Capture 6 value. * @param TIMx where x can be 1 or 8 to select the TIM peripheral. * @return Capture Compare 6 Register value. */ uint16_t TIM_GetCap6(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimList1Module(TIMx)); /* Get the Capture 6 Register value */ return TIMx->CCDAT6; } /** * @brief Gets the TIMx Counter value. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @return Counter Register value. */ uint16_t TIM_GetCnt(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); /* Get the Counter Register value */ return TIMx->CNT; } /** * @brief Gets the TIMx Prescaler value. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @return Prescaler Register value. */ uint16_t TIM_GetPrescaler(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); /* Get the Prescaler Register value */ return TIMx->PSC; } /** * @brief Gets the TIMx Prescaler value. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @return Prescaler Register value. */ uint16_t TIM_GetAutoReload(TIM_Module* TIMx) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); /* Get the Prescaler Register value */ return TIMx->AR; } /** * @brief Checks whether the specified TIM flag is set or not. * @param TIMx where x can be 1 to 5 , 8 to select the TIM peripheral. * @param TIM_CCEN specifies the Bit to check. * This parameter can be one of the following values: * @arg TIM_CC1EN CC1EN Bit * @arg TIM_CC1NEN CC1NEN Bit * @arg TIM_CC2EN CC2EN Bit * @arg TIM_CC2NEN CC2NEN Bit * @arg TIM_CC3EN CC3EN Bit * @arg TIM_CC3NEN CC3NEN Bit * @arg TIM_CC4EN CC4EN Bit * @arg TIM_CC5EN CC5EN Bit * @arg TIM_CC6EN CC6EN Bit * @note * - TIM_CC1NEN TIM_CC2NEN TIM_CC3NEN is used only with TIM1, TIM8. * @return The new state of TIM_FLAG (SET or RESET). */ FlagStatus TIM_GetCCENStatus(TIM_Module* TIMx, uint32_t TIM_CCEN) { INTStatus bitstatus = RESET; /* Check the parameters */ assert_param(IsTimList3Module(TIMx)); if(TIMx==TIM1 || TIMx==TIM8) { assert_param(IsAdvancedTimCCENFlag(TIM_CCEN)); if ((TIMx->CCEN & TIM_CCEN) != (uint32_t)RESET) { bitstatus = SET; } else { bitstatus = RESET; } } else if(TIMx==TIM2 || TIMx==TIM3 || TIMx==TIM4 || TIMx==TIM5 ) { assert_param(IsGeneralTimCCENFlag(TIM_CCEN)); if ((TIMx->CCEN & TIM_CCEN) != (uint32_t)RESET) { bitstatus = SET; } else { bitstatus = RESET; } } return bitstatus; } /** * @brief Checks whether the specified TIM flag is set or not. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param TIM_FLAG specifies the flag to check. * This parameter can be one of the following values: * @arg TIM_FLAG_UPDATE TIM update Flag * @arg TIM_FLAG_CC1 TIM Capture Compare 1 Flag * @arg TIM_FLAG_CC2 TIM Capture Compare 2 Flag * @arg TIM_FLAG_CC3 TIM Capture Compare 3 Flag * @arg TIM_FLAG_CC4 TIM Capture Compare 4 Flag * @arg TIM_FLAG_COM TIM Commutation Flag * @arg TIM_FLAG_TRIG TIM Trigger Flag * @arg TIM_FLAG_BREAK TIM Break Flag * @arg TIM_FLAG_CC1OF TIM Capture Compare 1 overcapture Flag * @arg TIM_FLAG_CC2OF TIM Capture Compare 2 overcapture Flag * @arg TIM_FLAG_CC3OF TIM Capture Compare 3 overcapture Flag * @arg TIM_FLAG_CC4OF TIM Capture Compare 4 overcapture Flag * @arg TIM_FLAG_CC5 TIM Capture Compare 5 Flag * @arg TIM_FLAG_CC6 TIM Capture Compare 6 Flag * @note * - TIM6 and TIM7 can have only one update flag. * - TIM_FLAG_BREAK is used only with TIM1, TIM8. * - TIM_FLAG_COM is used only with TIM1, TIM8. * @return The new state of TIM_FLAG (SET or RESET). */ FlagStatus TIM_GetFlagStatus(TIM_Module* TIMx, uint32_t TIM_FLAG) { INTStatus bitstatus = RESET; /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimGetFlag(TIM_FLAG)); if ((TIMx->STS & TIM_FLAG) != (uint32_t)RESET) { bitstatus = SET; } else { bitstatus = RESET; } return bitstatus; } /** * @brief Clears the TIMx's pending flags. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param TIM_FLAG specifies the flag bit to clear. * This parameter can be any combination of the following values: * @arg TIM_FLAG_UPDATE TIM update Flag * @arg TIM_FLAG_CC1 TIM Capture Compare 1 Flag * @arg TIM_FLAG_CC2 TIM Capture Compare 2 Flag * @arg TIM_FLAG_CC3 TIM Capture Compare 3 Flag * @arg TIM_FLAG_CC4 TIM Capture Compare 4 Flag * @arg TIM_FLAG_COM TIM Commutation Flag * @arg TIM_FLAG_TRIG TIM Trigger Flag * @arg TIM_FLAG_BREAK TIM Break Flag * @arg TIM_FLAG_CC1OF TIM Capture Compare 1 overcapture Flag * @arg TIM_FLAG_CC2OF TIM Capture Compare 2 overcapture Flag * @arg TIM_FLAG_CC3OF TIM Capture Compare 3 overcapture Flag * @arg TIM_FLAG_CC4OF TIM Capture Compare 4 overcapture Flag * @note * - TIM6 and TIM7 can have only one update flag. * - TIM_FLAG_BREAK is used only with TIM1, TIM8. * - TIM_FLAG_COM is used only with TIM1, TIM8. */ void TIM_ClearFlag(TIM_Module* TIMx, uint32_t TIM_FLAG) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimClrFlag(TIM_FLAG)); /* Clear the flags */ TIMx->STS &= (uint32_t)~TIM_FLAG; } /** * @brief Checks whether the TIM interrupt has occurred or not. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param TIM_IT specifies the TIM interrupt source to check. * This parameter can be one of the following values: * @arg TIM_INT_UPDATE TIM update Interrupt source * @arg TIM_INT_CC1 TIM Capture Compare 1 Interrupt source * @arg TIM_INT_CC2 TIM Capture Compare 2 Interrupt source * @arg TIM_INT_CC3 TIM Capture Compare 3 Interrupt source * @arg TIM_INT_CC4 TIM Capture Compare 4 Interrupt source * @arg TIM_INT_COM TIM Commutation Interrupt source * @arg TIM_INT_TRIG TIM Trigger Interrupt source * @arg TIM_INT_BREAK TIM Break Interrupt source * @note * - TIM6 and TIM7 can generate only an update interrupt. * - TIM_INT_BREAK is used only with TIM1, TIM8. * - TIM_INT_COM is used only with TIM1, TIM8. * @return The new state of the TIM_IT(SET or RESET). */ INTStatus TIM_GetIntStatus(TIM_Module* TIMx, uint32_t TIM_IT) { INTStatus bitstatus = RESET; uint32_t itstatus = 0x0, itenable = 0x0; /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimGetInt(TIM_IT)); itstatus = TIMx->STS & TIM_IT; itenable = TIMx->DINTEN & TIM_IT; if ((itstatus != (uint32_t)RESET) && (itenable != (uint32_t)RESET)) { bitstatus = SET; } else { bitstatus = RESET; } return bitstatus; } /** * @brief Clears the TIMx's interrupt pending bits. * @param TIMx where x can be 1 to 8 to select the TIM peripheral. * @param TIM_IT specifies the pending bit to clear. * This parameter can be any combination of the following values: * @arg TIM_INT_UPDATE TIM1 update Interrupt source * @arg TIM_INT_CC1 TIM Capture Compare 1 Interrupt source * @arg TIM_INT_CC2 TIM Capture Compare 2 Interrupt source * @arg TIM_INT_CC3 TIM Capture Compare 3 Interrupt source * @arg TIM_INT_CC4 TIM Capture Compare 4 Interrupt source * @arg TIM_INT_COM TIM Commutation Interrupt source * @arg TIM_INT_TRIG TIM Trigger Interrupt source * @arg TIM_INT_BREAK TIM Break Interrupt source * @note * - TIM6 and TIM7 can generate only an update interrupt. * - TIM_INT_BREAK is used only with TIM1, TIM8. * - TIM_INT_COM is used only with TIM1, TIM8. */ void TIM_ClrIntPendingBit(TIM_Module* TIMx, uint32_t TIM_IT) { /* Check the parameters */ assert_param(IsTimAllModule(TIMx)); assert_param(IsTimInt(TIM_IT)); /* Clear the IT pending Bit */ TIMx->STS &= (uint32_t)~TIM_IT; } /** * @brief Configure the TI1 as Input. * @param TIMx where x can be 1 to 8 except 6 and 7 to select the TIM peripheral. * @param IcPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_IC_POLARITY_RISING * @arg TIM_IC_POLARITY_FALLING * @param IcSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_IC_SELECTION_DIRECTTI TIM Input 1 is selected to be connected to IC1. * @arg TIM_IC_SELECTION_INDIRECTTI TIM Input 1 is selected to be connected to IC2. * @arg TIM_IC_SELECTION_TRC TIM Input 1 is selected to be connected to TRC. * @param IcFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. */ static void ConfigTI1(TIM_Module* TIMx, uint16_t IcPolarity, uint16_t IcSelection, uint16_t IcFilter) { uint16_t tmpccmr1 = 0; uint32_t tmpccer = 0; /* Disable the Channel 1: Reset the CC1E Bit */ TIMx->CCEN &= (uint32_t) ~((uint32_t)TIM_CCEN_CC1EN); tmpccmr1 = TIMx->CCMOD1; tmpccer = TIMx->CCEN; /* Select the Input and set the filter */ tmpccmr1 &= (uint16_t)(((uint16_t) ~((uint16_t)TIM_CCMOD1_CC1SEL)) & ((uint16_t) ~((uint16_t)TIM_CCMOD1_IC1F))); tmpccmr1 |= (uint16_t)(IcSelection | (uint16_t)(IcFilter << (uint16_t)4)); if ((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4) || (TIMx == TIM5)) { /* Select the Polarity and set the CC1E Bit */ tmpccer &= (uint32_t) ~((uint32_t)(TIM_CCEN_CC1P)); tmpccer |= (uint32_t)(IcPolarity | (uint32_t)TIM_CCEN_CC1EN); } else { /* Select the Polarity and set the CC1E Bit */ tmpccer &= (uint32_t) ~((uint32_t)(TIM_CCEN_CC1P | TIM_CCEN_CC1NP)); tmpccer |= (uint32_t)(IcPolarity | (uint32_t)TIM_CCEN_CC1EN); } /* Write to TIMx CCMOD1 and CCEN registers */ TIMx->CCMOD1 = tmpccmr1; TIMx->CCEN = tmpccer; } /** * @brief Configure the TI2 as Input. * @param TIMx where x can be 1, 2, 3, 4, 5, 8 to select the TIM peripheral. * @param IcPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_IC_POLARITY_RISING * @arg TIM_IC_POLARITY_FALLING * @param IcSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_IC_SELECTION_DIRECTTI TIM Input 2 is selected to be connected to IC2. * @arg TIM_IC_SELECTION_INDIRECTTI TIM Input 2 is selected to be connected to IC1. * @arg TIM_IC_SELECTION_TRC TIM Input 2 is selected to be connected to TRC. * @param IcFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. */ static void ConfigTI2(TIM_Module* TIMx, uint16_t IcPolarity, uint16_t IcSelection, uint16_t IcFilter) { uint16_t tmpccmr1 = 0; uint32_t tmpccer = 0, tmp = 0; /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCEN &= (uint32_t) ~((uint32_t)TIM_CCEN_CC2EN); tmpccmr1 = TIMx->CCMOD1; tmpccer = TIMx->CCEN; tmp = (uint32_t)(IcPolarity << 4); /* Select the Input and set the filter */ tmpccmr1 &= (uint16_t)(((uint16_t) ~((uint16_t)TIM_CCMOD1_CC2SEL)) & ((uint16_t) ~((uint16_t)TIM_CCMOD1_IC2F))); tmpccmr1 |= (uint16_t)(IcFilter << 12); tmpccmr1 |= (uint16_t)(IcSelection << 8); if ((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4) || (TIMx == TIM5)) { /* Select the Polarity and set the CC2E Bit */ tmpccer &= (uint32_t) ~((uint32_t)(TIM_CCEN_CC2P)); tmpccer |= (uint32_t)(tmp | (uint32_t)TIM_CCEN_CC2EN); } else { /* Select the Polarity and set the CC2E Bit */ tmpccer &= (uint32_t) ~((uint32_t)(TIM_CCEN_CC2P | TIM_CCEN_CC2NP)); tmpccer |= (uint32_t)(IcPolarity | (uint32_t)TIM_CCEN_CC2EN); } /* Write to TIMx CCMOD1 and CCEN registers */ TIMx->CCMOD1 = tmpccmr1; TIMx->CCEN = tmpccer; } /** * @brief Configure the TI3 as Input. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param IcPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_IC_POLARITY_RISING * @arg TIM_IC_POLARITY_FALLING * @param IcSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_IC_SELECTION_DIRECTTI TIM Input 3 is selected to be connected to IC3. * @arg TIM_IC_SELECTION_INDIRECTTI TIM Input 3 is selected to be connected to IC4. * @arg TIM_IC_SELECTION_TRC TIM Input 3 is selected to be connected to TRC. * @param IcFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. */ static void ConfigTI3(TIM_Module* TIMx, uint16_t IcPolarity, uint16_t IcSelection, uint16_t IcFilter) { uint16_t tmpccmr2 = 0; uint32_t tmpccer = 0, tmp = 0; /* Disable the Channel 3: Reset the CC3E Bit */ TIMx->CCEN &= (uint32_t) ~((uint32_t)TIM_CCEN_CC3EN); tmpccmr2 = TIMx->CCMOD2; tmpccer = TIMx->CCEN; tmp = (uint32_t)(IcPolarity << 8); /* Select the Input and set the filter */ tmpccmr2 &= (uint16_t)(((uint16_t) ~((uint16_t)TIM_CCMOD2_CC3SEL)) & ((uint16_t) ~((uint16_t)TIM_CCMOD2_IC3F))); tmpccmr2 |= (uint16_t)(IcSelection | (uint16_t)(IcFilter << (uint16_t)4)); if ((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4) || (TIMx == TIM5)) { /* Select the Polarity and set the CC3E Bit */ tmpccer &= (uint32_t) ~((uint32_t)(TIM_CCEN_CC3P)); tmpccer |= (uint32_t)(tmp | (uint32_t)TIM_CCEN_CC3EN); } else { /* Select the Polarity and set the CC3E Bit */ tmpccer &= (uint32_t) ~((uint32_t)(TIM_CCEN_CC3P | TIM_CCEN_CC3NP)); tmpccer |= (uint32_t)(IcPolarity | (uint32_t)TIM_CCEN_CC3EN); } /* Write to TIMx CCMOD2 and CCEN registers */ TIMx->CCMOD2 = tmpccmr2; TIMx->CCEN = tmpccer; } /** * @brief Configure the TI4 as Input. * @param TIMx where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. * @param IcPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_IC_POLARITY_RISING * @arg TIM_IC_POLARITY_FALLING * @param IcSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_IC_SELECTION_DIRECTTI TIM Input 4 is selected to be connected to IC4. * @arg TIM_IC_SELECTION_INDIRECTTI TIM Input 4 is selected to be connected to IC3. * @arg TIM_IC_SELECTION_TRC TIM Input 4 is selected to be connected to TRC. * @param IcFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. */ static void ConfigTI4(TIM_Module* TIMx, uint16_t IcPolarity, uint16_t IcSelection, uint16_t IcFilter) { uint16_t tmpccmr2 = 0; uint32_t tmpccer = 0, tmp = 0; /* Disable the Channel 4: Reset the CC4E Bit */ TIMx->CCEN &= (uint32_t) ~((uint32_t)TIM_CCEN_CC4EN); tmpccmr2 = TIMx->CCMOD2; tmpccer = TIMx->CCEN; tmp = (uint32_t)(IcPolarity << 12); /* Select the Input and set the filter */ tmpccmr2 &= (uint16_t)((uint16_t)(~(uint16_t)TIM_CCMOD2_CC4SEL) & ((uint16_t) ~((uint16_t)TIM_CCMOD2_IC4F))); tmpccmr2 |= (uint16_t)(IcSelection << 8); tmpccmr2 |= (uint16_t)(IcFilter << 12); if ((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) || (TIMx == TIM4) || (TIMx == TIM5)) { /* Select the Polarity and set the CC4E Bit */ tmpccer &= (uint32_t) ~((uint32_t)(TIM_CCEN_CC4P)); tmpccer |= (uint32_t)(tmp | (uint32_t)TIM_CCEN_CC4EN); } else { /* Select the Polarity and set the CC4E Bit */ tmpccer &= (uint32_t) ~((uint32_t)(TIM_CCEN_CC4P)); tmpccer |= (uint32_t)(IcPolarity | (uint32_t)TIM_CCEN_CC4EN); } /* Write to TIMx CCMOD2 and CCEN registers */ TIMx->CCMOD2 = tmpccmr2; TIMx->CCEN = tmpccer; } /** * @} */ /** * @} */ /** * @} */