menu "Hardware Drivers Config"

config SOC_STM32H750XB
    bool
    select SOC_SERIES_STM32H7
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_USB_TO_USART
        bool "Enable Debuger USART (uart4)"
        select BSP_USING_UART
        select BSP_USING_UART4
        default n

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default n
        select RT_USING_SERIAL
        select RT_SERIAL_USING_DMA
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default n

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART1_TX_USING_DMA
                bool "Enable UART1 TX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n
                
            config BSP_USING_UART3
                bool "Enable UART3"
                default n
                
            config BSP_USING_UART4
                bool "Enable UART4"
                default n
                
            config BSP_USING_UART6
                bool "Enable UART6"
                default n
        endif

    config BSP_USING_ONCHIP_RTC
        bool "Enable Onchip RTC"
        select RT_USING_RTC
        default n

    menuconfig BSP_USING_I2C
        bool "Enable I2C BUS (software simulation)"
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        default n
        if BSP_USING_I2C
            menuconfig BSP_USING_I2C1
                bool "Enable I2C1 BUS (software simulation)"
                default n
                select RT_USING_I2C
                select RT_USING_I2C_BITOPS
                select RT_USING_PIN
                if BSP_USING_I2C1
                    comment "Notice: PB6 --> 22; PB7 --> 23" 
                    config BSP_I2C1_SCL_PIN
                        int "I2C1 scl pin number"
                        range 0 175
                        default 22
                    config BSP_I2C1_SDA_PIN
                        int "I2C1 sda pin number"
                        range 0 175
                        default 23
                endif
            menuconfig BSP_USING_I2C2
                bool "Enable I2C2 BUS (software simulation)"
                default n
                if BSP_USING_I2C2
                    comment "Notice: PH13 --> 125; PH15 --> 127"
                    config BSP_I2C2_SCL_PIN
                        int "i2c2 scl pin number"
                        range 1 176
                        default 127
                    config BSP_I2C2_SDA_PIN
                        int "I2C2 sda pin number"
                        range 0 175
                        default 125
                endif
            menuconfig BSP_USING_I2C3
                bool "Enable I2C3 BUS (software simulation)"
                default n
                if BSP_USING_I2C3
                    comment "Notice: PH12 --> 124; PH11 --> 123"
                    config BSP_I2C3_SCL_PIN
                        int "i2c3 scl pin number"
                        range 0 175
                        default 123
                    config BSP_I2C3_SDA_PIN
                        int "I2C3 sda pin number"
                        range 0 175
                        default 124
                endif
        endif
        
    source "../libraries/HAL_Drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu