Skip to content

R
rt-thread

人间散章 / rt-thread
与 Fork 源项目一致

Fork自 RT-Thread / rt-thread

通知 1
Star 1
Fork 0
R
rt-thread

前往新版Gitcode，体验更适合开发者的 AI 搜索 >>

提交 67b86e61 编写于 作者: C chenjh
浏览文件
操作

[uart] Modify the uart file to configure uart_pin for pullup

上级 c0096e2d
展开全部 显示空白变更内容
内联 并排
Showing with 2852 addition and 2653 deletion
bsp/stm32/libraries/templates/stm32f0xx/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -31,20 +31,22 @@ NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SVC_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
PA10.Mode=Synchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_SWCLK
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA8.Mode=Synchronous
PA8.Signal=USART1_CK
PA9.Mode=Synchronous
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PCC.Checker=false
PCC.Line=STM32F0x1
PCC.MCU=STM32F091R(B-C)Tx
......
bsp/stm32/libraries/templates/stm32f0xx/board/CubeMX_Config/Src/stm32f0xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -114,7 +114,6 @@ void HAL_USART_MspInit(USART_HandleTypeDef* husart)
/* USER CODE END USART1_MspInit 0 */
/* Peripheral clock enable */
__HAL_RCC_USART1_CLK_ENABLE();
__HAL_RCC_GPIOA_CLK_ENABLE();
/**USART1 GPIO Configuration
PA8 ------> USART1_CK
......@@ -221,7 +220,6 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
/* USER CODE END USART2_MspDeInit 0 */
/* Peripheral clock disable */
__HAL_RCC_USART2_CLK_DISABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
......
bsp/stm32/libraries/templates/stm32f10x/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -33,14 +33,18 @@ NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PCC.Checker=false
PCC.Line=STM32F103
PCC.MCU=STM32F103R(8-B)Tx
......
bsp/stm32/libraries/templates/stm32f10x/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -117,7 +117,6 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
/* USER CODE END USART1_MspInit 0 */
/* Peripheral clock enable */
__HAL_RCC_USART1_CLK_ENABLE();
__HAL_RCC_GPIOA_CLK_ENABLE();
/**USART1 GPIO Configuration
PA9 ------> USART1_TX
......@@ -158,7 +157,6 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
/* USER CODE END USART1_MspDeInit 0 */
/* Peripheral clock disable */
__HAL_RCC_USART1_CLK_DISABLE();
/**USART1 GPIO Configuration
PA9 ------> USART1_TX
PA10 ------> USART1_RX
......
bsp/stm32/libraries/templates/stm32f2xx/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -35,16 +35,24 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PC6.GPIOParameters=GPIO_PuPd
PC6.GPIO_PuPd=GPIO_PULLUP
PC6.Mode=Asynchronous
PC6.Signal=USART6_TX
PC7.GPIOParameters=GPIO_PuPd
PC7.GPIO_PuPd=GPIO_PULLUP
PC7.Mode=Asynchronous
PC7.Signal=USART6_RX
PCC.Checker=false
......
bsp/stm32/libraries/templates/stm32f4xx/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -33,14 +33,18 @@ NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PCC.Checker=false
PCC.Line=STM32F407/417
PCC.MCU=STM32F407Z(E-G)Tx
......
bsp/stm32/libraries/templates/stm32f7xx/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -32,12 +32,14 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA10.Locked=true
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA9.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PCC.Checker=false
PCC.Line=STM32F7x7
PCC.MCU=STM32F767I(G-I)Tx
......
bsp/stm32/libraries/templates/stm32h7xx/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -34,16 +34,18 @@ NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA10.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13\ (JTMS/SWDIO).Mode=Serial_Wire
PA13\ (JTMS/SWDIO).Signal=SYS_JTMS-SWDIO
PA14\ (JTCK/SWCLK).Mode=Serial_Wire
PA14\ (JTCK/SWCLK).Signal=SYS_JTCK-SWCLK
PA9.Locked=true
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PCC.Checker=false
PCC.Line=STM32H743/753
PCC.MCU=STM32H743IITx
......
bsp/stm32/libraries/templates/stm32l4xx/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -33,14 +33,18 @@ NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13\ (JTMS-SWDIO).Mode=Serial_Wire
PA13\ (JTMS-SWDIO).Signal=SYS_JTMS-SWDIO
PA14\ (JTCK-SWCLK).Mode=Serial_Wire
PA14\ (JTCK-SWCLK).Signal=SYS_JTCK-SWCLK
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PCC.Checker=true
PCC.Line=STM32L4x5
PCC.MCU=STM32L475V(C-E-G)Tx
......
bsp/stm32/stm32f072-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -44,7 +44,7 @@ PA14.Signal=SYS_SWCLK
PA2.GPIOParameters=GPIO_Speed,GPIO_PuPd,GPIO_Label,GPIO_Mode
PA2.GPIO_Label=USART_TX
PA2.GPIO_Mode=GPIO_MODE_AF_PP
PA2.GPIO_PuPd=GPIO_NOPULL
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.GPIO_Speed=GPIO_SPEED_FREQ_LOW
PA2.Locked=true
PA2.Mode=Asynchronous
......@@ -52,7 +52,7 @@ PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_Speed,GPIO_PuPd,GPIO_Label,GPIO_Mode
PA3.GPIO_Label=USART_RX
PA3.GPIO_Mode=GPIO_MODE_AF_PP
PA3.GPIO_PuPd=GPIO_NOPULL
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.GPIO_Speed=GPIO_SPEED_FREQ_LOW
PA3.Locked=true
PA3.Mode=Asynchronous
......
bsp/stm32/stm32f072-st-nucleo/board/CubeMX_Config/Src/stm32f0xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -121,7 +121,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = USART_TX_Pin|USART_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF1_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32f091-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -37,9 +37,9 @@ Mcu.Pin4=PA3
Mcu.Pin5=PA6
Mcu.Pin6=PA7
Mcu.Pin7=PB11
Mcu.Pin8=PA8
Mcu.Pin9=PA9
Mcu.PinsNb=21
Mcu.Pin8=PA9
Mcu.Pin9=PA10
Mcu.PinsNb=20
Mcu.ThirdPartyNb=0
Mcu.UserConstants=
Mcu.UserName=STM32F091RCTx
......@@ -52,23 +52,29 @@ NVIC.SVC_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
PA0.Mode=IN0
PA0.Signal=ADC_IN0
PA10.Mode=Synchronous
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_SWCLK
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA6.Mode=Full_Duplex_Master
PA6.Signal=SPI1_MISO
PA7.Mode=Full_Duplex_Master
PA7.Signal=SPI1_MOSI
PA8.Mode=Synchronous
PA8.Signal=USART1_CK
PA9.Mode=Synchronous
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB11.Signal=S_TIM2_CH4
PB3.Locked=true
......@@ -147,8 +153,8 @@ SPI1.Mode=SPI_MODE_MASTER
SPI1.VirtualType=VM_MASTER
TIM2.Channel-PWM\ Generation4\ CH4=TIM_CHANNEL_4
TIM2.IPParameters=Channel-PWM Generation4 CH4
USART1.IPParameters=VirtualMode-Synchronous
USART1.VirtualMode-Synchronous=VM_SYNC
USART1.IPParameters=VirtualMode-Asynchronous
USART1.VirtualMode-Asynchronous=VM_ASYNC
USART2.IPParameters=VirtualMode-Asynchronous
USART2.VirtualMode-Asynchronous=VM_ASYNC
VP_IWDG_VS_IWDG.Mode=IWDG_Activate
......
bsp/stm32/stm32f091-st-nucleo/board/CubeMX_Config/Src/stm32f0xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -418,15 +418,15 @@ void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim_base)
}
/**
* @brief USART MSP Initialization
* @brief UART MSP Initialization
* This function configures the hardware resources used in this example
* @param husart: USART handle pointer
* @param huart: UART handle pointer
* @retval None
*/
void HAL_USART_MspInit(USART_HandleTypeDef* husart)
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
if(husart->Instance==USART1)
if(huart->Instance==USART1)
{
/* USER CODE BEGIN USART1_MspInit 0 */
......@@ -436,13 +436,12 @@ void HAL_USART_MspInit(USART_HandleTypeDef* husart)
__HAL_RCC_GPIOA_CLK_ENABLE();
/**USART1 GPIO Configuration
PA8 ------> USART1_CK
PA9 ------> USART1_TX
PA10 ------> USART1_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......@@ -451,19 +450,7 @@ void HAL_USART_MspInit(USART_HandleTypeDef* husart)
/* USER CODE END USART1_MspInit 1 */
}
}
/**
* @brief UART MSP Initialization
* This function configures the hardware resources used in this example
* @param huart: UART handle pointer
* @retval None
*/
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
if(huart->Instance==USART2)
else if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
......@@ -478,7 +465,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......@@ -491,14 +478,14 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
}
/**
* @brief USART MSP De-Initialization
* @brief UART MSP De-Initialization
* This function freeze the hardware resources used in this example
* @param husart: USART handle pointer
* @param huart: UART handle pointer
* @retval None
*/
void HAL_USART_MspDeInit(USART_HandleTypeDef* husart)
void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
{
if(husart->Instance==USART1)
if(huart->Instance==USART1)
{
/* USER CODE BEGIN USART1_MspDeInit 0 */
......@@ -507,28 +494,16 @@ void HAL_USART_MspDeInit(USART_HandleTypeDef* husart)
__HAL_RCC_USART1_CLK_DISABLE();
/**USART1 GPIO Configuration
PA8 ------> USART1_CK
PA9 ------> USART1_TX
PA10 ------> USART1_RX
*/
HAL_GPIO_DeInit(GPIOA, GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10);
HAL_GPIO_DeInit(GPIOA, GPIO_PIN_9|GPIO_PIN_10);
/* USER CODE BEGIN USART1_MspDeInit 1 */
/* USER CODE END USART1_MspDeInit 1 */
}
}
/**
* @brief UART MSP De-Initialization
* This function freeze the hardware resources used in this example
* @param huart: UART handle pointer
* @retval None
*/
void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
{
if(huart->Instance==USART2)
else if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspDeInit 0 */
......
bsp/stm32/stm32f103-atk-nano/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -437,7 +437,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USART1 interrupt Init */
......
bsp/stm32/stm32f103-atk-warshipv3/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -95,12 +95,16 @@ OSC_IN.Mode=HSE-External-Oscillator
OSC_IN.Signal=RCC_OSC_IN
OSC_OUT.Mode=HSE-External-Oscillator
OSC_OUT.Signal=RCC_OSC_OUT
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PC10.Mode=SD_4_bits_Wide_bus
......@@ -121,14 +125,6 @@ PC8.Mode=SD_4_bits_Wide_bus
PC8.Signal=SDIO_D0
PC9.Mode=SD_4_bits_Wide_bus
PC9.Signal=SDIO_D1
PCC.Checker=false
PCC.Line=STM32F103
PCC.MCU=STM32F103Z(C-D-E)Tx
PCC.PartNumber=STM32F103ZETx
PCC.Seq0=0
PCC.Series=STM32F1
PCC.Temperature=25
PCC.Vdd=3.3
PD0.Signal=FSMC_D2_DA2
PD1.Signal=FSMC_D3_DA3
PD10.Signal=FSMC_D15_DA15
......@@ -184,7 +180,7 @@ ProjectManager.CustomerFirmwarePackage=
ProjectManager.DefaultFWLocation=true
ProjectManager.DeletePrevious=true
ProjectManager.DeviceId=STM32F103ZETx
ProjectManager.FirmwarePackage=STM32Cube FW_F1 V1.8.0
ProjectManager.FirmwarePackage=STM32Cube FW_F1 V1.8.4
ProjectManager.FreePins=false
ProjectManager.HalAssertFull=false
ProjectManager.HeapSize=0x200
......@@ -197,11 +193,12 @@ ProjectManager.PreviousToolchain=
ProjectManager.ProjectBuild=false
ProjectManager.ProjectFileName=CubeMX_Config.ioc
ProjectManager.ProjectName=CubeMX_Config
ProjectManager.RegisterCallBack=
ProjectManager.StackSize=0x400
ProjectManager.TargetToolchain=MDK-ARM V5
ProjectManager.ToolChainLocation=
ProjectManager.UnderRoot=false
ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-SystemClock_Config-RCC-false-HAL-false,3-MX_USART1_UART_Init-USART1-false-HAL-true,4-MX_FSMC_Init-FSMC-false-HAL-true,5-MX_TIM3_Init-TIM3-false-HAL-true
ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-SystemClock_Config-RCC-false-HAL-false,3-MX_USART1_UART_Init-USART1-false-HAL-true,4-MX_FSMC_Init-FSMC-false-HAL-true,5-MX_TIM3_Init-TIM3-false-HAL-true,6-MX_SDIO_SD_Init-SDIO-false-HAL-true
RCC.ADCFreqValue=36000000
RCC.AHBFreq_Value=72000000
RCC.APB1CLKDivider=RCC_HCLK_DIV2
......
bsp/stm32/stm32f103-atk-warshipv3/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -256,7 +256,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
......@@ -294,73 +294,6 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
}
}
/**
* @brief CAN MSP Initialization
* This function configures the hardware resources used in this example
* @param hcan: CAN handle pointer
* @retval None
*/
void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
if(hcan->Instance==CAN1)
{
/* USER CODE BEGIN CAN1_MspInit 0 */
/* USER CODE END CAN1_MspInit 0 */
/* Peripheral clock enable */
__HAL_RCC_CAN1_CLK_ENABLE();
__HAL_RCC_GPIOA_CLK_ENABLE();
/**CAN GPIO Configuration
PA11 ------> CAN_RX
PA12 ------> CAN_TX
*/
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_12;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN CAN1_MspInit 1 */
/* USER CODE END CAN1_MspInit 1 */
}
}
/**
* @brief CAN MSP De-Initialization
* This function freeze the hardware resources used in this example
* @param hcan: CAN handle pointer
* @retval None
*/
void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan)
{
if(hcan->Instance==CAN1)
{
/* USER CODE BEGIN CAN1_MspDeInit 0 */
/* USER CODE END CAN1_MspDeInit 0 */
/* Peripheral clock disable */
__HAL_RCC_CAN1_CLK_DISABLE();
/**CAN GPIO Configuration
PA11 ------> CAN_RX
PA12 ------> CAN_TX
*/
HAL_GPIO_DeInit(GPIOA, GPIO_PIN_11|GPIO_PIN_12);
/* USER CODE BEGIN CAN1_MspDeInit 1 */
/* USER CODE END CAN1_MspDeInit 1 */
}
}
static uint32_t FSMC_Initialized = 0;
......
bsp/stm32/stm32f103-blue-pill/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -57,6 +57,8 @@ NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA1.Signal=ADCx_IN1
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA11.Mode=Device
......@@ -67,8 +69,12 @@ PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA5.Mode=Full_Duplex_Master
......@@ -77,6 +83,8 @@ PA6.Mode=Full_Duplex_Master
PA6.Signal=SPI1_MISO
PA7.Mode=Full_Duplex_Master
PA7.Signal=SPI1_MOSI
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PC13-TAMPER-RTC.GPIOParameters=GPIO_Speed,PinState,GPIO_ModeDefaultOutputPP
......@@ -103,7 +111,7 @@ ProjectManager.CustomerFirmwarePackage=
ProjectManager.DefaultFWLocation=true
ProjectManager.DeletePrevious=true
ProjectManager.DeviceId=STM32F103C8Tx
ProjectManager.FirmwarePackage=STM32Cube FW_F1 V1.8.3
ProjectManager.FirmwarePackage=STM32Cube FW_F1 V1.8.4
ProjectManager.FreePins=false
ProjectManager.HalAssertFull=false
ProjectManager.HeapSize=0x200
......
bsp/stm32/stm32f103-blue-pill/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -287,7 +287,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
......@@ -314,7 +314,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART2_MspInit 1 */
......
bsp/stm32/stm32f103-dofly-M3S/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -57,6 +57,12 @@ OSC_IN.Mode=HSE-External-Oscillator
OSC_IN.Signal=RCC_OSC_IN
OSC_OUT.Mode=HSE-External-Oscillator
OSC_OUT.Signal=RCC_OSC_OUT
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
......@@ -69,8 +75,6 @@ PA6.Mode=Full_Duplex_Master
PA6.Signal=SPI1_MISO
PA7.Mode=Full_Duplex_Master
PA7.Signal=SPI1_MOSI
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB13.Mode=Full_Duplex_Master
PB13.Signal=SPI2_SCK
PB14.Mode=Full_Duplex_Master
......
bsp/stm32/stm32f103-dofly-M3S/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -355,7 +355,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
......
bsp/stm32/stm32f103-dofly-lyc8/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -34,14 +34,18 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PC14-OSC32_IN.Mode=LSE-External-Oscillator
PC14-OSC32_IN.Signal=RCC_OSC32_IN
PC15-OSC32_OUT.Mode=LSE-External-Oscillator
......
bsp/stm32/stm32f103-dofly-lyc8/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -131,7 +131,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
......
bsp/stm32/stm32f103-fire-arbitrary/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -645,7 +645,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USART1 interrupt Init */
......@@ -675,7 +675,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART2_MspInit 1 */
......@@ -702,7 +702,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/* USER CODE BEGIN USART3_MspInit 1 */
......
bsp/stm32/stm32f103-gizwits-gokitv21/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -34,6 +34,10 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
......@@ -42,8 +46,6 @@ PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PC14-OSC32_IN.Mode=LSE-External-Oscillator
PC14-OSC32_IN.Signal=RCC_OSC32_IN
PC15-OSC32_OUT.Mode=LSE-External-Oscillator
......
bsp/stm32/stm32f103-hw100k-ibox/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -68,14 +68,24 @@ OSC_IN.Mode=HSE-External-Oscillator
OSC_IN.Signal=RCC_OSC_IN
OSC_OUT.Mode=HSE-External-Oscillator
OSC_OUT.Signal=RCC_OSC_OUT
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA5.Mode=Full_Duplex_Master
......@@ -84,10 +94,12 @@ PA6.Mode=Full_Duplex_Master
PA6.Signal=SPI1_MISO
PA7.Mode=Full_Duplex_Master
PA7.Signal=SPI1_MOSI
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB10.GPIOParameters=GPIO_PuPd
PB10.GPIO_PuPd=GPIO_PULLUP
PB10.Mode=Asynchronous
PB10.Signal=USART3_TX
PB11.GPIOParameters=GPIO_PuPd
PB11.GPIO_PuPd=GPIO_PULLUP
PB11.Mode=Asynchronous
PB11.Signal=USART3_RX
PB13.Mode=Full_Duplex_Master
......
bsp/stm32/stm32f103-hw100k-ibox/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -366,7 +366,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/* USER CODE BEGIN UART4_MspInit 1 */
......@@ -393,7 +393,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
......@@ -420,7 +420,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART2_MspInit 1 */
......@@ -447,7 +447,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/* USER CODE BEGIN USART3_MspInit 1 */
......
bsp/stm32/stm32f103-onenet-nbiot/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -43,34 +43,42 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA10.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.Locked=true
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.Locked=true
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA9.Locked=true
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB10.Locked=true
PB10.GPIOParameters=GPIO_PuPd
PB10.GPIO_PuPd=GPIO_PULLUP
PB10.Mode=Asynchronous
PB10.Signal=USART3_TX
PB11.Locked=true
PB11.GPIOParameters=GPIO_PuPd
PB11.GPIO_PuPd=GPIO_PULLUP
PB11.Mode=Asynchronous
PB11.Signal=USART3_RX
PC10.Locked=true
PC10.GPIOParameters=GPIO_PuPd
PC10.GPIO_PuPd=GPIO_PULLUP
PC10.Mode=Asynchronous
PC10.Signal=UART4_TX
PC11.Locked=true
PC10.Signal=USART4_TX
PC11.GPIOParameters=GPIO_PuPd
PC11.GPIO_PuPd=GPIO_PULLUP
PC11.Mode=Asynchronous
PC11.Signal=UART4_RX
PC11.Signal=USART4_RX
PD0-OSC_IN.Locked=true
PD0-OSC_IN.Mode=HSE-External-Oscillator
PD0-OSC_IN.Signal=RCC_OSC_IN
......
bsp/stm32/stm32f103-onenet-nbiot/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -110,7 +110,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/* USER CODE BEGIN UART4_MspInit 1 */
......@@ -137,7 +137,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
......@@ -164,7 +164,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART2_MspInit 1 */
......@@ -191,7 +191,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/* USER CODE BEGIN USART3_MspInit 1 */
......
bsp/stm32/stm32f103-yf-ufun/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -47,6 +47,12 @@ NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA0-WKUP.Signal=S_TIM2_CH1_ETR
PA1.Signal=S_TIM2_CH2
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
......@@ -54,8 +60,6 @@ PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.Signal=S_TIM2_CH3
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PC10.Mode=SD_4_bits_Wide_bus
PC10.Signal=SDIO_D2
PC11.Mode=SD_4_bits_Wide_bus
......
bsp/stm32/stm32f103-yf-ufun/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -282,7 +282,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
......
bsp/stm32/stm32f107-uc-eval/board/CubeMX_Config/Src/stm32f1xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -131,7 +131,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
GPIO_InitStruct.Pin = GPIO_PIN_6;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
__HAL_AFIO_REMAP_USART2_ENABLE();
......
bsp/stm32/stm32f207-st-nucleo/board/CubeMX_Config/Core/Src/stm32f2xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -101,7 +101,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
......
bsp/stm32/stm32f401-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -42,11 +42,13 @@ PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.GPIOParameters=GPIO_Speed
PA2.GPIOParameters=GPIO_Speed,GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.GPIO_Speed=GPIO_SPEED_FREQ_LOW
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_Speed
PA3.GPIOParameters=GPIO_Speed,GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.GPIO_Speed=GPIO_SPEED_FREQ_LOW
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
......@@ -61,14 +63,6 @@ PC14-OSC32_IN.Mode=LSE-External-Oscillator
PC14-OSC32_IN.Signal=RCC_OSC32_IN
PC15-OSC32_OUT.Mode=LSE-External-Oscillator
PC15-OSC32_OUT.Signal=RCC_OSC32_OUT
PCC.Checker=false
PCC.Line=STM32F401
PCC.MCU=STM32F401R(D-E)Tx
PCC.PartNumber=STM32F401RETx
PCC.Seq0=0
PCC.Series=STM32F4
PCC.Temperature=25
PCC.Vdd=null
PH0\ -\ OSC_IN.Mode=HSE-External-Clock-Source
PH0\ -\ OSC_IN.Signal=RCC_OSC_IN
PH1\ -\ OSC_OUT.Mode=HSE-External-Clock-Source
......
bsp/stm32/stm32f405-smdz-breadfruit/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -32,8 +32,12 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PC14-OSC32_IN.Mode=LSE-External-Oscillator
......
bsp/stm32/stm32f407-armfly-v5/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -85,18 +85,26 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB1.Signal=ADCx_IN9
PB12.Mode=Full_Duplex_Master
PB12.Signal=I2S2_WS
......
bsp/stm32/stm32f407-armfly-v5/board/CubeMX_Config/Src/stm32f4xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -631,7 +631,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......@@ -655,7 +655,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32f407-atk-explorer/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -136,6 +136,12 @@ NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA1.Mode=RMII
PA1.Signal=ETH_REF_CLK
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA11.Mode=Device_Only
......@@ -154,10 +160,12 @@ PA5.Locked=true
PA5.Signal=COMP_DAC2_group
PA7.Mode=RMII
PA7.Signal=ETH_CRS_DV
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB10.GPIOParameters=GPIO_PuPd
PB10.GPIO_PuPd=GPIO_PULLUP
PB10.Mode=Asynchronous
PB10.Signal=USART3_TX
PB11.GPIOParameters=GPIO_PuPd
PB11.GPIO_PuPd=GPIO_PULLUP
PB11.Mode=Asynchronous
PB11.Signal=USART3_RX
PB13.Mode=Full_Duplex_Master
......
bsp/stm32/stm32f407-atk-explorer/board/CubeMX_Config/Src/stm32f4xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -741,7 +741,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......@@ -768,7 +768,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
......
bsp/stm32/stm32f407-robomaster-c/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -38,10 +38,12 @@ PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA9.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB7.Locked=true
PB7.GPIOParameters=GPIO_PuPd
PB7.GPIO_PuPd=GPIO_PULLUP
PB7.Mode=Asynchronous
PB7.Signal=USART1_RX
PH0-OSC_IN.Mode=HSE-External-Oscillator
......
bsp/stm32/stm32f407-robomaster-c/board/CubeMX_Config/Src/stm32f4xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -102,14 +102,14 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_7;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32f407-st-discovery/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -25,18 +25,19 @@ Mcu.PinsNb=11
Mcu.ThirdPartyNb=0
Mcu.UserConstants=
Mcu.UserName=STM32F407VGTx
MxCube.Version=5.0.0
MxDb.Version=DB.5.0.0
NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:true
MxCube.Version=6.2.1
MxDb.Version=DB.6.0.21
NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:true\:false
NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:true\:false
NVIC.ForceEnableDMAVector=true
NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:true\:false
NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:true\:false
NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:true\:false
NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:true\:false
NVIC.PriorityGroup=NVIC_PRIORITYGROUP_0
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:true\:false
PA13.GPIOParameters=GPIO_Label
PA13.GPIO_Label=SWDIO
PA13.Locked=true
......@@ -75,18 +76,14 @@ PB3.GPIOParameters=GPIO_Label
PB3.GPIO_Label=SWO
PB3.Locked=true
PB3.Signal=SYS_JTDO-SWO
PB6.GPIOParameters=GPIO_PuPd
PB6.GPIO_PuPd=GPIO_PULLUP
PB6.Mode=Asynchronous
PB6.Signal=USART1_TX
PB7.GPIOParameters=GPIO_PuPd
PB7.GPIO_PuPd=GPIO_PULLUP
PB7.Mode=Asynchronous
PB7.Signal=USART1_RX
PCC.Checker=false
PCC.Line=STM32F407/417
PCC.MCU=STM32F407V(E-G)Tx
PCC.PartNumber=STM32F407VGTx
PCC.Seq0=0
PCC.Series=STM32F4
PCC.Temperature=25
PCC.Vdd=3.3
PH0-OSC_IN.GPIOParameters=GPIO_Label
PH0-OSC_IN.GPIO_Label=PH0-OSC_IN
PH0-OSC_IN.Locked=true
......
bsp/stm32/stm32f407-st-discovery/board/CubeMX_Config/Src/stm32f4xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -117,7 +117,6 @@ void HAL_MspInit(void)
*/
void HAL_SPI_MspInit(SPI_HandleTypeDef* hspi)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
if(hspi->Instance==SPI1)
{
......@@ -153,10 +152,8 @@ void HAL_SPI_MspInit(SPI_HandleTypeDef* hspi)
* @param hspi: SPI handle pointer
* @retval None
*/
void HAL_SPI_MspDeInit(SPI_HandleTypeDef* hspi)
{
if(hspi->Instance==SPI1)
{
/* USER CODE BEGIN SPI1_MspDeInit 0 */
......@@ -187,7 +184,6 @@ void HAL_SPI_MspDeInit(SPI_HandleTypeDef* hspi)
*/
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
if(huart->Instance==USART1)
{
......@@ -222,10 +218,8 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
* @param huart: UART handle pointer
* @retval None
*/
void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
{
if(huart->Instance==USART1)
{
/* USER CODE BEGIN USART1_MspDeInit 0 */
......
bsp/stm32/stm32f410-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -48,14 +48,12 @@ PA14.GPIO_Label=TCK
PA14.Locked=true
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.GPIOParameters=GPIO_Label
PA2.GPIO_Label=USART_TX
PA2.Locked=true
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_Label
PA3.GPIO_Label=USART_RX
PA3.Locked=true
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA5.GPIOParameters=GPIO_Label
......
bsp/stm32/stm32f410-st-nucleo/board/CubeMX_Config/Src/stm32f4xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -103,7 +103,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = USART_TX_Pin|USART_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32f411-atk-nano/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -57,18 +57,26 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB1.Locked=true
PB1.Signal=ADCx_IN9
PB13.Locked=true
......
bsp/stm32/stm32f411-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -69,8 +69,12 @@ PA14.GPIO_Label=TCK
PA14.Locked=true
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA5.Mode=Full_Duplex_Master
......
bsp/stm32/stm32f411-weact-MiniF4/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -49,6 +49,12 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA11.Mode=Device_Only
......@@ -65,8 +71,6 @@ PA6.Mode=Full_Duplex_Master
PA6.Signal=SPI1_MISO
PA7.Mode=Full_Duplex_Master
PA7.Signal=SPI1_MOSI
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PC13-ANTI_TAMP.Locked=true
PC13-ANTI_TAMP.Signal=GPIO_Output
PC14-OSC32_IN.Mode=LSE-External-Oscillator
......
bsp/stm32/stm32f411-weact-MiniF4/board/CubeMX_Config/Src/stm32f4xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -278,7 +278,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32f429-armfly-v6/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -175,6 +175,12 @@ NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA0/WKUP.Signal=S_TIM2_CH1_ETR
PA1.Mode=RMII
PA1.Signal=ETH_REF_CLK
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
......@@ -185,8 +191,6 @@ PA2.Mode=RMII
PA2.Signal=ETH_MDIO
PA7.Mode=RMII
PA7.Signal=ETH_CRS_DV
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB13.Mode=RMII
PB13.Signal=ETH_TXD1
PB3.Locked=true
......
bsp/stm32/stm32f429-fire-challenger/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -153,6 +153,12 @@ NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA1.Mode=RMII
PA1.Signal=ETH_REF_CLK
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA11.Mode=RGB888
......@@ -170,8 +176,6 @@ PA3.Mode=RGB888
PA3.Signal=LTDC_B5
PA7.Mode=RMII
PA7.Signal=ETH_CRS_DV
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB0.Locked=true
PB0.Mode=RGB888
PB0.Signal=LTDC_R3
......
bsp/stm32/stm32f429-st-disco/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -194,15 +194,15 @@ PA1.GPIO_ModeDefaultEXTI=GPIO_MODE_EVT_RISING
PA1.GPIO_PuPd=GPIO_NOPULL
PA1.Locked=true
PA1.Signal=GPXTI1
PA10.GPIOParameters=GPIO_Label
PA10.GPIOParameters=GPIO_Label,GPIO_PuPd
PA10.GPIO_Label=STLINK_TX [STM32F103CBT6_PA2]
PA10.Locked=true
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA11.GPIOParameters=GPIO_Speed,GPIO_PuPd,GPIO_Label,GPIO_Mode
PA11.GPIO_Label=R4
PA11.GPIO_Mode=GPIO_MODE_AF_PP
PA11.GPIO_PuPd=GPIO_NOPULL
PA11.GPIO_PuPd=GPIO_PULLUP
PA11.GPIO_Speed=GPIO_SPEED_FREQ_LOW
PA11.Locked=true
PA11.Mode=RGB565
......@@ -210,7 +210,7 @@ PA11.Signal=LTDC_R4
PA12.GPIOParameters=GPIO_Speed,GPIO_PuPd,GPIO_Label,GPIO_Mode
PA12.GPIO_Label=R5
PA12.GPIO_Mode=GPIO_MODE_AF_PP
PA12.GPIO_PuPd=GPIO_NOPULL
PA12.GPIO_PuPd=GPIO_PULLUP
PA12.GPIO_Speed=GPIO_SPEED_FREQ_LOW
PA12.Locked=true
PA12.Mode=RGB565
......@@ -276,9 +276,9 @@ PA8.GPIO_Speed=GPIO_SPEED_FREQ_LOW
PA8.Locked=true
PA8.Mode=I2C
PA8.Signal=I2C3_SCL
PA9.GPIOParameters=GPIO_Label
PA9.GPIOParameters=GPIO_Label,GPIO_PULLUP
PA9.GPIO_Label=STLINK_RX [STM32F103CBT6_PA3]
PA9.Locked=true
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB0.GPIOParameters=GPIO_Speed,GPIO_PuPd,GPIO_Label,GPIO_Mode
......
bsp/stm32/stm32f446-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -34,14 +34,14 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
PA13.Signal=SYS_JTMS-SWDIO
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PC14-OSC32_IN.Mode=LSE-External-Oscillator
PC14-OSC32_IN.Signal=RCC_OSC32_IN
PC15-OSC32_OUT.Mode=LSE-External-Oscillator
......
bsp/stm32/stm32f469-st-disco/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -182,10 +182,12 @@ PA15.GPIOParameters=GPIO_Speed
PA15.GPIO_Speed=GPIO_SPEED_FREQ_HIGH
PA15.Mode=Half_Duplex_Master
PA15.Signal=I2S3_WS
PB10.Locked=true
PB10.GPIOParameters=GPIO_PuPd
PB10.GPIO_PuPd=GPIO_PULLUP
PB10.Mode=Asynchronous
PB10.Signal=USART3_TX
PB11.Locked=true
PB11.GPIOParameters=GPIO_PuPd
PB11.GPIO_PuPd=GPIO_PULLUP
PB11.Mode=Asynchronous
PB11.Signal=USART3_RX
PB3.GPIOParameters=GPIO_Speed
......
bsp/stm32/stm32f746-st-disco/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -142,15 +142,18 @@ PA2.Mode=RMII
PA2.Signal=ETH_MDIO
PA7.Mode=RMII
PA7.Signal=ETH_CRS_DV
PA9.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB7.GPIOParameters=GPIO_PuPd
PB7.GPIO_PuPd=GPIO_PULLUP
PB7.Mode=Asynchronous
PB7.Signal=USART1_RX
PB2.Mode=Single Bank 1
PB2.Signal=QUADSPI_CLK
PB6.Mode=Single Bank 1
PB6.Signal=QUADSPI_BK1_NCS
PB7.Mode=Asynchronous
PB7.Signal=USART1_RX
PC1.Mode=RMII
PC1.Signal=ETH_MDC
PC10.Mode=SD_4_bits_Wide_bus
......
bsp/stm32/stm32f746-st-disco/board/CubeMX_Config/Src/stm32f7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -615,14 +615,14 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_7;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32f767-atk-apollo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -161,7 +161,12 @@ NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA1.Mode=RMII
PA1.Signal=ETH_REF_CLK
PA10.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA11.Mode=Host_Only
......@@ -182,9 +187,6 @@ PA7.Mode=RMII
PA7.Signal=ETH_CRS_DV
PA8.Mode=RGB565
PA8.Signal=LTDC_B3
PA9.Locked=true
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB0.Locked=true
PB0.Signal=S_TIM3_CH3
PB1.Mode=RGB565
......
bsp/stm32/stm32f767-atk-apollo/board/CubeMX_Config/Src/stm32f7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -974,7 +974,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......@@ -998,7 +998,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_5|GPIO_PIN_6;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
......
bsp/stm32/stm32f767-fire-challenger-v1/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -138,7 +138,12 @@ NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA1.Mode=RMII
PA1.Signal=ETH_REF_CLK
PA10.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA11.GPIOParameters=GPIO_Speed
......@@ -160,9 +165,6 @@ PA3.Signal=LTDC_B5
PA5.Signal=ADCx_IN5
PA7.Mode=RMII
PA7.Signal=ETH_CRS_DV
PA9.Locked=true
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB0.GPIOParameters=GPIO_Speed
PB0.GPIO_Speed=GPIO_SPEED_FREQ_VERY_HIGH
PB0.Mode=RGB888
......
bsp/stm32/stm32f767-fire-challenger-v1/board/CubeMX_Config/Src/stm32f7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -730,7 +730,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/Src/stm32f7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -234,7 +234,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = STLK_RX_Pin|STLK_TX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
......
bsp/stm32/stm32f769-st-disco/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -60,7 +60,12 @@ NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA1.Mode=MII
PA1.Signal=ETH_RX_CLK
PA10.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13.Mode=Serial_Wire
......@@ -71,9 +76,6 @@ PA2.Mode=MII
PA2.Signal=ETH_MDIO
PA7.Mode=MII
PA7.Signal=ETH_RX_DV
PA9.Locked=true
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PC1.Mode=MII
PC1.Signal=ETH_MDC
PC12.Locked=true
......
bsp/stm32/stm32f769-st-disco/board/CubeMX_Config/Src/stm32f7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -237,14 +237,14 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_12;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF8_UART5;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF8_UART5;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
......@@ -268,7 +268,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32g070-st-nucleo/board/CubeMX_Config/Src/stm32g0xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -434,7 +434,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_4|GPIO_PIN_5;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF1_USART1;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
......@@ -483,14 +483,14 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF0_USART3;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF4_USART3;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
......
bsp/stm32/stm32g071-st-nucleo/board/CubeMX_Config/Src/stm32g0xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -256,7 +256,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = LPUART1_TX_Pin|LPUART1_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF6_LPUART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32g431-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -57,18 +57,24 @@ PA14.GPIO_Label=T_SWCLK
PA14.Locked=true
PA14.Mode=Serial_Wire
PA14.Signal=SYS_JTCK-SWCLK
PA2.Locked=true
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=LPUART1_TX
PA3.Locked=true
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=LPUART1_RX
PA3.Signal=USART2_RX
PA5.GPIOParameters=GPIO_Label
PA5.GPIO_Label=LD2 [green]
PA5.Locked=true
PA5.Signal=GPIO_Output
PB10.GPIOParameters=GPIO_PuPd
PB10.GPIO_PuPd=GPIO_PULLUP
PB10.Mode=Asynchronous
PB10.Signal=USART3_TX
PB11.GPIOParameters=GPIO_PuPd
PB11.GPIO_PuPd=GPIO_PULLUP
PB11.Mode=Asynchronous
PB11.Signal=USART3_RX
PB3.GPIOParameters=GPIO_Label
......
bsp/stm32/stm32g431-st-nucleo/board/CubeMX_Config/Src/stm32g4xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -105,7 +105,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF12_LPUART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......@@ -129,7 +129,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF5_UART4;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
......@@ -153,7 +153,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = USART1_TX_Pin|USART1_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
......@@ -177,7 +177,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
......
bsp/stm32/stm32h743-atk-apollo/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -161,23 +161,29 @@ NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true\:true
NVIC.USART2_IRQn=true\:0\:0\:false\:false\:true\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA10.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA13\ (JTMS/SWDIO).Mode=Serial_Wire
PA13\ (JTMS/SWDIO).Signal=DEBUG_JTMS-SWDIO
PA14\ (JTCK/SWCLK).Mode=Serial_Wire
PA14\ (JTCK/SWCLK).Signal=DEBUG_JTCK-SWCLK
PA2.GPIOParameters=GPIO_PuPd
PA2.GPIO_PuPd=GPIO_PULLUP
PA2.Mode=Asynchronous
PA2.Signal=USART2_TX
PA3.GPIOParameters=GPIO_PuPd
PA3.GPIO_PuPd=GPIO_PULLUP
PA3.Mode=Asynchronous
PA3.Signal=USART2_RX
PA4.Signal=COMP_DAC11_group
PA5.Locked=true
PA5.Signal=ADCx_INP19
PA9.Locked=true
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB13.GPIOParameters=GPIO_Speed
PB13.GPIO_Speed=GPIO_SPEED_FREQ_HIGH
PB13.Locked=true
......
bsp/stm32/stm32h743-atk-apollo/board/CubeMX_Config/Src/stm32h7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -735,7 +735,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......@@ -762,7 +762,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32h743-st-nucleo/board/CubeMX_Config/Src/stm32h7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -100,7 +100,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
......
bsp/stm32/stm32h747-st-discovery/board/CubeMX_Config/CM7/Src/stm32h7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -100,7 +100,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32h747-st-discovery/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -52,13 +52,15 @@ NVIC2.PriorityGroup=NVIC_PRIORITYGROUP_4
NVIC2.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC2.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC2.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA10.GPIOParameters=PinAttribute
PA10.GPIOParameters=PinAttribute,GPIO_PuPd
PA10.Locked=true
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.PinAttribute=CortexM7
PA10.Signal=USART1_RX
PA9.GPIOParameters=PinAttribute
PA9.GPIOParameters=PinAttribute,GPIO_PuPd
PA9.Locked=true
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.PinAttribute=CortexM7
PA9.Signal=USART1_TX
......
bsp/stm32/stm32h750-armfly-h7-tool/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -103,7 +103,12 @@ NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA1.Mode=RMII
PA1.Signal=ETH_REF_CLK
PA10.Locked=true
PA9.GPIOParameters=GPIO_PuPd
PA9.GPIO_PuPd=GPIO_PULLUP
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PA10.GPIOParameters=GPIO_PuPd
PA10.GPIO_PuPd=GPIO_PULLUP
PA10.Mode=Asynchronous
PA10.Signal=USART1_RX
PA2.Mode=RMII
......@@ -115,9 +120,6 @@ PA5.Mode=Device_HS
PA5.Signal=USB_OTG_HS_ULPI_CK
PA7.Mode=RMII
PA7.Signal=ETH_CRS_DV
PA9.Locked=true
PA9.Mode=Asynchronous
PA9.Signal=USART1_TX
PB0.Mode=Device_HS
PB0.Signal=USB_OTG_HS_ULPI_D1
PB1.Mode=Device_HS
......
bsp/stm32/stm32h750-armfly-h7-tool/board/CubeMX_Config/Src/stm32h7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -715,7 +715,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_13|GPIO_PIN_14;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF8_UART4;
HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
......@@ -739,7 +739,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32h750-artpi-h750/.config
浏览文件 @ 67b86e61
......@@ -21,6 +21,12 @@ CONFIG_RT_USING_IDLE_HOOK=y
CONFIG_RT_IDLE_HOOK_LIST_SIZE=4
CONFIG_IDLE_THREAD_STACK_SIZE=256
# CONFIG_RT_USING_TIMER_SOFT is not set
#
# kservice optimization
#
# CONFIG_RT_KSERVICE_USING_STDLIB is not set
# CONFIG_RT_KSERVICE_USING_TINY_SIZE is not set
CONFIG_RT_DEBUG=y
# CONFIG_RT_DEBUG_COLOR is not set
# CONFIG_RT_DEBUG_INIT_CONFIG is not set
......@@ -52,6 +58,7 @@ CONFIG_RT_USING_MEMPOOL=y
# CONFIG_RT_USING_NOHEAP is not set
CONFIG_RT_USING_SMALL_MEM=y
# CONFIG_RT_USING_SLAB is not set
# CONFIG_RT_USING_USERHEAP is not set
# CONFIG_RT_USING_MEMTRACE is not set
CONFIG_RT_USING_HEAP=y
......@@ -64,7 +71,7 @@ CONFIG_RT_USING_DEVICE=y
CONFIG_RT_USING_CONSOLE=y
CONFIG_RT_CONSOLEBUF_SIZE=128
CONFIG_RT_CONSOLE_DEVICE_NAME="uart4"
CONFIG_RT_VER_NUM=0x40003
CONFIG_RT_VER_NUM=0x40004
CONFIG_ARCH_ARM=y
CONFIG_RT_USING_CPU_FFS=y
CONFIG_ARCH_ARM_CORTEX_M=y
......@@ -115,6 +122,8 @@ CONFIG_RT_USING_DEVICE_IPC=y
CONFIG_RT_PIPE_BUFSZ=512
# CONFIG_RT_USING_SYSTEM_WORKQUEUE is not set
CONFIG_RT_USING_SERIAL=y
CONFIG_RT_USING_SERIAL_V1=y
# CONFIG_RT_USING_SERIAL_V2 is not set
# CONFIG_RT_SERIAL_USING_DMA is not set
CONFIG_RT_SERIAL_RB_BUFSZ=64
# CONFIG_RT_USING_CAN is not set
......@@ -153,6 +162,7 @@ CONFIG_RT_USING_PIN=y
# CONFIG_RT_USING_LIBC is not set
# CONFIG_RT_USING_PTHREADS is not set
CONFIG_RT_LIBC_USING_TIME=y
CONFIG_RT_LIBC_FIXED_TIMEZONE=8
#
# Network
......@@ -189,8 +199,14 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_RT_USING_RYM is not set
# CONFIG_RT_USING_ULOG is not set
# CONFIG_RT_USING_UTEST is not set
# CONFIG_RT_USING_RT_LINK is not set
# CONFIG_RT_USING_LWP is not set
#
# RT-Thread Utestcases
#
# CONFIG_RT_USING_UTESTCASES is not set
#
# RT-Thread online packages
#
......@@ -258,8 +274,6 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_LIBRWS is not set
# CONFIG_PKG_USING_TCPSERVER is not set
# CONFIG_PKG_USING_PROTOBUF_C is not set
# CONFIG_PKG_USING_ONNX_PARSER is not set
# CONFIG_PKG_USING_ONNX_BACKEND is not set
# CONFIG_PKG_USING_DLT645 is not set
# CONFIG_PKG_USING_QXWZ is not set
# CONFIG_PKG_USING_SMTP_CLIENT is not set
......@@ -271,6 +285,12 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_NMEALIB is not set
# CONFIG_PKG_USING_AGILE_JSMN is not set
# CONFIG_PKG_USING_PDULIB is not set
# CONFIG_PKG_USING_BTSTACK is not set
# CONFIG_PKG_USING_LORAWAN_ED_STACK is not set
# CONFIG_PKG_USING_WAYZ_IOTKIT is not set
# CONFIG_PKG_USING_MAVLINK is not set
# CONFIG_PKG_USING_RAPIDJSON is not set
# CONFIG_PKG_USING_BSAL is not set
#
# security packages
......@@ -296,6 +316,9 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_STEMWIN is not set
# CONFIG_PKG_USING_WAVPLAYER is not set
# CONFIG_PKG_USING_TJPGD is not set
# CONFIG_PKG_USING_HELIX is not set
# CONFIG_PKG_USING_AZUREGUIX is not set
# CONFIG_PKG_USING_TOUCHGFX2RTT is not set
#
# tools packages
......@@ -307,9 +330,12 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_RDB is not set
# CONFIG_PKG_USING_QRCODE is not set
# CONFIG_PKG_USING_ULOG_EASYFLASH is not set
# CONFIG_PKG_USING_ULOG_FILE is not set
# CONFIG_PKG_USING_LOGMGR is not set
# CONFIG_PKG_USING_ADBD is not set
# CONFIG_PKG_USING_COREMARK is not set
# CONFIG_PKG_USING_DHRYSTONE is not set
# CONFIG_PKG_USING_MEMORYPERF is not set
# CONFIG_PKG_USING_NR_MICRO_SHELL is not set
# CONFIG_PKG_USING_CHINESE_FONT_LIBRARY is not set
# CONFIG_PKG_USING_LUNAR_CALENDAR is not set
......@@ -317,6 +343,18 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_GPS_RMC is not set
# CONFIG_PKG_USING_URLENCODE is not set
# CONFIG_PKG_USING_UMCN is not set
# CONFIG_PKG_USING_LWRB2RTT is not set
# CONFIG_PKG_USING_CPU_USAGE is not set
# CONFIG_PKG_USING_GBK2UTF8 is not set
# CONFIG_PKG_USING_VCONSOLE is not set
# CONFIG_PKG_USING_KDB is not set
# CONFIG_PKG_USING_WAMR is not set
# CONFIG_PKG_USING_MICRO_XRCE_DDS_CLIENT is not set
# CONFIG_PKG_USING_LWLOG is not set
# CONFIG_PKG_USING_ANV_TRACE is not set
# CONFIG_PKG_USING_ANV_MEMLEAK is not set
# CONFIG_PKG_USING_ANV_TESTSUIT is not set
# CONFIG_PKG_USING_ANV_BENCH is not set
#
# system packages
......@@ -335,6 +373,8 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_CMSIS is not set
# CONFIG_PKG_USING_DFS_YAFFS is not set
# CONFIG_PKG_USING_LITTLEFS is not set
# CONFIG_PKG_USING_DFS_JFFS2 is not set
# CONFIG_PKG_USING_DFS_UFFS is not set
# CONFIG_PKG_USING_THREAD_POOL is not set
# CONFIG_PKG_USING_ROBOTS is not set
# CONFIG_PKG_USING_EV is not set
......@@ -344,7 +384,25 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_RAMDISK is not set
# CONFIG_PKG_USING_MININI is not set
# CONFIG_PKG_USING_QBOOT is not set
#
# Micrium: Micrium software products porting for RT-Thread
#
# CONFIG_PKG_USING_UCOSIII_WRAPPER is not set
# CONFIG_PKG_USING_UCOSII_WRAPPER is not set
# CONFIG_PKG_USING_UC_CRC is not set
# CONFIG_PKG_USING_UC_CLK is not set
# CONFIG_PKG_USING_UC_COMMON is not set
# CONFIG_PKG_USING_UC_MODBUS is not set
# CONFIG_PKG_USING_PPOOL is not set
# CONFIG_PKG_USING_OPENAMP is not set
# CONFIG_PKG_USING_RT_KPRINTF_THREADSAFE is not set
# CONFIG_PKG_USING_RT_MEMCPY_CM is not set
# CONFIG_PKG_USING_QFPLIB_M0_FULL is not set
# CONFIG_PKG_USING_QFPLIB_M0_TINY is not set
# CONFIG_PKG_USING_QFPLIB_M3 is not set
# CONFIG_PKG_USING_LPM is not set
# CONFIG_PKG_USING_TLSF is not set
#
# peripheral libraries and drivers
......@@ -353,6 +411,7 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_REALTEK_AMEBA is not set
# CONFIG_PKG_USING_SHT2X is not set
# CONFIG_PKG_USING_SHT3X is not set
# CONFIG_PKG_USING_AS7341 is not set
# CONFIG_PKG_USING_STM32_SDIO is not set
# CONFIG_PKG_USING_ICM20608 is not set
# CONFIG_PKG_USING_U8G2 is not set
......@@ -397,6 +456,28 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_AGILE_CONSOLE is not set
# CONFIG_PKG_USING_LD3320 is not set
# CONFIG_PKG_USING_WK2124 is not set
# CONFIG_PKG_USING_LY68L6400 is not set
# CONFIG_PKG_USING_DM9051 is not set
# CONFIG_PKG_USING_SSD1306 is not set
# CONFIG_PKG_USING_QKEY is not set
# CONFIG_PKG_USING_RS485 is not set
# CONFIG_PKG_USING_NES is not set
# CONFIG_PKG_USING_VIRTUAL_SENSOR is not set
# CONFIG_PKG_USING_VDEVICE is not set
# CONFIG_PKG_USING_SGM706 is not set
# CONFIG_PKG_USING_RDA58XX is not set
#
# AI packages
#
# CONFIG_PKG_USING_LIBANN is not set
# CONFIG_PKG_USING_NNOM is not set
# CONFIG_PKG_USING_ONNX_BACKEND is not set
# CONFIG_PKG_USING_ONNX_PARSER is not set
# CONFIG_PKG_USING_TENSORFLOWLITEMICRO is not set
# CONFIG_PKG_USING_ELAPACK is not set
# CONFIG_PKG_USING_ULAPACK is not set
# CONFIG_PKG_USING_QUEST is not set
#
# miscellaneous packages
......@@ -406,6 +487,7 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_FASTLZ is not set
# CONFIG_PKG_USING_MINILZO is not set
# CONFIG_PKG_USING_QUICKLZ is not set
# CONFIG_PKG_USING_LZMA is not set
# CONFIG_PKG_USING_MULTIBUTTON is not set
# CONFIG_PKG_USING_FLEXIBLE_BUTTON is not set
# CONFIG_PKG_USING_CANFESTIVAL is not set
......@@ -426,16 +508,72 @@ CONFIG_RT_LIBC_USING_TIME=y
# CONFIG_PKG_USING_PERIPHERAL_SAMPLES is not set
# CONFIG_PKG_USING_HELLO is not set
# CONFIG_PKG_USING_VI is not set
# CONFIG_PKG_USING_NNOM is not set
# CONFIG_PKG_USING_LIBANN is not set
# CONFIG_PKG_USING_ELAPACK is not set
# CONFIG_PKG_USING_KI is not set
# CONFIG_PKG_USING_ARMv7M_DWT is not set
# CONFIG_PKG_USING_VT100 is not set
# CONFIG_PKG_USING_ULAPACK is not set
# CONFIG_PKG_USING_UKAL is not set
# CONFIG_PKG_USING_CRCLIB is not set
#
# games: games run on RT-Thread console
#
# CONFIG_PKG_USING_THREES is not set
# CONFIG_PKG_USING_2048 is not set
# CONFIG_PKG_USING_SNAKE is not set
# CONFIG_PKG_USING_TETRIS is not set
# CONFIG_PKG_USING_LWGPS is not set
# CONFIG_PKG_USING_STATE_MACHINE is not set
# CONFIG_PKG_USING_MCURSES is not set
# CONFIG_PKG_USING_COWSAY is not set
#
# Privated Packages of RealThread
#
# CONFIG_PKG_USING_CODEC is not set
# CONFIG_PKG_USING_PLAYER is not set
# CONFIG_PKG_USING_MPLAYER is not set
# CONFIG_PKG_USING_PERSIMMON_SRC is not set
# CONFIG_PKG_USING_JS_PERSIMMON is not set
# CONFIG_PKG_USING_JERRYSCRIPT_WIN32 is not set
#
# Network Utilities
#
# CONFIG_PKG_USING_WICED is not set
# CONFIG_PKG_USING_CLOUDSDK is not set
# CONFIG_PKG_USING_POWER_MANAGER is not set
# CONFIG_PKG_USING_RT_OTA is not set
# CONFIG_PKG_USING_RTINSIGHT is not set
# CONFIG_PKG_USING_SMARTCONFIG is not set
# CONFIG_PKG_USING_RTX is not set
# CONFIG_RT_USING_TESTCASE is not set
# CONFIG_PKG_USING_NGHTTP2 is not set
# CONFIG_PKG_USING_AVS is not set
# CONFIG_PKG_USING_ALI_LINKKIT is not set
# CONFIG_PKG_USING_STS is not set
# CONFIG_PKG_USING_DLMS is not set
# CONFIG_PKG_USING_AUDIO_FRAMEWORK is not set
# CONFIG_PKG_USING_ZBAR is not set
# CONFIG_PKG_USING_MCF is not set
# CONFIG_PKG_USING_URPC is not set
# CONFIG_PKG_USING_DCM is not set
# CONFIG_PKG_USING_EMQ is not set
# CONFIG_PKG_USING_CFGM is not set
# CONFIG_PKG_USING_RT_CMSIS_DAP is not set
# CONFIG_PKG_USING_SMODULE is not set
# CONFIG_PKG_USING_SNFD is not set
# CONFIG_PKG_USING_UDBD is not set
# CONFIG_PKG_USING_BENCHMARK is not set
# CONFIG_PKG_USING_UBJSON is not set
# CONFIG_PKG_USING_DATATYPE is not set
# CONFIG_PKG_USING_FASTFS is not set
# CONFIG_PKG_USING_RIL is not set
# CONFIG_PKG_USING_WATCH_DCM_SVC is not set
# CONFIG_PKG_USING_WATCH_APP_FWK is not set
# CONFIG_PKG_USING_GUI_TEST is not set
# CONFIG_PKG_USING_PMEM is not set
# CONFIG_PKG_USING_LWRDP is not set
# CONFIG_PKG_USING_MASAN is not set
CONFIG_SOC_FAMILY_STM32=y
CONFIG_SOC_SERIES_STM32H7=y
......
bsp/stm32/stm32h750-artpi-h750/board/CubeMX_Config/Core/Inc/main.h
浏览文件 @ 67b86e61
......@@ -51,7 +51,7 @@ extern "C" {
/* USER CODE END EM */
/* Exported functions prototypes ---------------------------------------------*/
void Error_Handler(void);
/* USER CODE BEGIN EFP */
......
bsp/stm32/stm32h750-artpi-h750/board/CubeMX_Config/Core/Src/stm32h7xx_hal_msp.c
浏览文件 @ 67b86e61
......@@ -101,14 +101,14 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
*/
GPIO_InitStruct.Pin = GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF8_UART4;
HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_0;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
GPIO_InitStruct.Alternate = GPIO_AF8_UART4;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
......
bsp/stm32/stm32h750-artpi-h750/board/CubeMX_Config/CubeMX_Config.ioc
浏览文件 @ 67b86e61
......@@ -27,8 +27,8 @@ Mcu.PinsNb=11
Mcu.ThirdPartyNb=0
Mcu.UserConstants=
Mcu.UserName=STM32H750XBHx
MxCube.Version=6.0.1
MxDb.Version=DB.6.0.0
MxCube.Version=6.2.1
MxDb.Version=DB.6.0.21
NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false\:false
NVIC.ForceEnableDMAVector=true
......@@ -42,13 +42,17 @@ NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
NVIC.UART4_IRQn=true\:0\:0\:false\:false\:true\:true\:true
NVIC.USART3_IRQn=true\:0\:0\:false\:false\:true\:true\:true
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
PA0.GPIOParameters=GPIO_PuPd
PA0.GPIO_PuPd=GPIO_PULLUP
PA0.Locked=true
PA0.Mode=Asynchronous
PA0.Signal=UART4_TX
PB10.Locked=true
PB10.GPIOParameters=GPIO_PuPd
PB10.GPIO_PuPd=GPIO_PULLUP
PB10.Mode=Asynchronous
PB10.Signal=USART3_TX
PB11.Locked=true
PB11.GPIOParameters=GPIO_PuPd
PB11.GPIO_PuPd=GPIO_PULLUP
PB11.Mode=Asynchronous
PB11.Signal=USART3_RX
PD11.Mode=CTS_RTS
......@@ -63,6 +67,8 @@ PI11.Locked=true
PI11.Signal=GPIO_Output
PI8.Locked=true
PI8.Signal=GPIO_Output
PI9.GPIOParameters=GPIO_PuPd
PI9.GPIO_PuPd=GPIO_PULLUP
PI9.Locked=true
PI9.Mode=Asynchronous
PI9.Signal=UART4_RX
......@@ -77,7 +83,7 @@ ProjectManager.CustomerFirmwarePackage=
ProjectManager.DefaultFWLocation=true
ProjectManager.DeletePrevious=true
ProjectManager.DeviceId=STM32H750XBHx
ProjectManager.FirmwarePackage=STM32Cube FW_H7 V1.8.0
ProjectManager.FirmwarePackage=STM32Cube FW_H7 V1.9.0
ProjectManager.FreePins=false
ProjectManager.HalAssertFull=false
ProjectManager.HeapSize=0x200
......
bsp/stm32/stm32h750-artpi-h750/rtconfig.h
浏览文件 @ 67b86e61
......@@ -16,6 +16,9 @@
#define RT_USING_IDLE_HOOK
#define RT_IDLE_HOOK_LIST_SIZE 4
#define IDLE_THREAD_STACK_SIZE 256
/* kservice optimization */
#define RT_DEBUG
/* Inter-Thread communication */
......@@ -38,7 +41,7 @@
#define RT_USING_CONSOLE
#define RT_CONSOLEBUF_SIZE 128
#define RT_CONSOLE_DEVICE_NAME "uart4"
#define RT_VER_NUM 0x40003
#define RT_VER_NUM 0x40004
#define ARCH_ARM
#define RT_USING_CPU_FFS
#define ARCH_ARM_CORTEX_M
......@@ -78,6 +81,7 @@
#define RT_USING_DEVICE_IPC
#define RT_PIPE_BUFSZ 512
#define RT_USING_SERIAL
#define RT_USING_SERIAL_V1
#define RT_SERIAL_RB_BUFSZ 64
#define RT_USING_PIN
......@@ -87,6 +91,7 @@
/* POSIX layer and C standard library */
#define RT_LIBC_USING_TIME
#define RT_LIBC_FIXED_TIMEZONE 8
/* Network */
......@@ -108,6 +113,9 @@
/* Utilities */
/* RT-Thread Utestcases */
/* RT-Thread online packages */
/* IoT - internet of things */
......@@ -139,14 +147,29 @@
/* system packages */
/* Micrium: Micrium software products porting for RT-Thread */
/* peripheral libraries and drivers */
/* AI packages */
/* miscellaneous packages */
/* samples: kernel and components samples */
/* games: games run on RT-Thread console */
/* Privated Packages of RealThread */
/* Network Utilities */
#define SOC_FAMILY_STM32
#define SOC_SERIES_STM32H7
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或