- 20 9月, 2011 5 次提交
-
-
由 Andiry Xu 提交于
When a xHC host is unable to handle isochronous transfer in the interval, it reports a Missed Service Error event and skips some tds. Currently xhci driver handles MSE event in the following ways: 1. When encounter a MSE event, set ep->skip flag, update event ring dequeue pointer and return. 2. When encounter the next event on this ep, the driver will run the do-while loop, fetch td from ep's td_list to find the td corresponding to this event. All tds missed are marked as short transfer(-EXDEV). The do-while loop will end in two ways: 1. If the td pointed by the event trb is found; 2. If the ep ring's td_list is empty. However, if a buggy HW reports some unpredicted event (for example, an overrun event following a MSE event while the ep ring is actually not empty), the driver will never find the td, and it will loop until the td_list is empty. Unfortunately, the spinlock is dropped when give back a urb in the do-while loop. During the spinlock released period, the class driver may still submit urbs and add tds to the td_list. This may cause disaster, since the td_list will never be empty and the loop never ends, and the system hangs. To fix this, count the number of TDs on the ep ring before skipping TDs, and quit the loop when skipped that number of tds. This guarantees the do-while loop will end after certain number of cycles, and driver will not be trapped in an infinite loop. Signed-off-by: NAndiry Xu <andiry.xu@amd.com> Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Greg KH 提交于
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther Point xHCI host controller will report a link state change with the state set to "SS.Inactive". This causes the xHCI host controller to issue a warm port reset, which doesn't finish before the USB core times out while waiting for it to complete. When the warm port reset does complete, and the xHC gives back a port status change event, the xHCI driver kicks khubd. However, it fails to set the bit indicating there is a change event for that port because the logic in xhci-hub.c doesn't check for the warm port reset bit. After that, the warm port status change bit is never cleared by the USB core, and the xHC stops reporting port status change bits. (The xHCI spec says it shouldn't report more port events until all change bits are cleared.) This means any port changes when a new device is connected will never be reported, and the port will seem "dead" until the xHCI driver is unloaded and reloaded, or the computer is rebooted. Fix this by making the xHCI driver set the port change bit when a warm port reset change bit is set. A better solution would be to make the USB core handle warm port reset in differently, merging the current code with the standard port reset code that does an incremental backoff on the timeout, and tries to complete the port reset two more times before giving up. That more complicated fix will be merged next window, and this fix will be backported to stable. This should be backported to kernels as old as 3.0, since that was the first kernel with commit a11496eb ("xHCI: warm reset support"). Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Randy Dunlap 提交于
Fix build when CONFIG_ISA_DMA_API is enabled but CONFIG_COMEDI_PCI[_DRIVERS] is not enabled. Fixes these build errors: drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd': drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size' drivers/staging/comedi/drivers/ni_labpc.c: At top level: drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size' drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
Even with just the interface limited to admin, there really is little to reason to give byte-per-byte counts for taskstats. So round it down to something less intrusive. Acked-by: NBalbir Singh <bsingharora@gmail.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
Ok, this isn't optimal, since it means that 'iotop' needs admin capabilities, and we may have to work on this some more. But at the same time it is very much not acceptable to let anybody just read anybody elses IO statistics quite at this level. Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative to checking the capabilities by hand. Reported-by: NVasiliy Kulikov <segoon@openwall.com> Cc: Johannes Berg <johannes.berg@intel.com> Acked-by: NBalbir Singh <bsingharora@gmail.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 19 9月, 2011 9 次提交
-
-
git://github.com/penberg/linux由 Linus Torvalds 提交于
* 'slab/urgent' of git://github.com/penberg/linux: slub: add slab with one free object to partial list tail
-
git://people.freedesktop.org/~airlied/linux由 Linus Torvalds 提交于
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2) drm/radeon/kms: fix typo in r100_blit_copy drm/radeon: Unreference GEM object outside of spinlock in page flip error path. drm/radeon: Don't read from CP ring write pointer registers. drm/ttm: request zeroed system memory pages for new TT buffer objects
-
git://github.com/davem330/net由 Linus Torvalds 提交于
* git://github.com/davem330/net: tcp: fix validation of D-SACK tcp: fix build error if !CONFIG_SYN_COOKIES
-
由 Zheng Yan 提交于
D-SACK is allowed to reside below snd_una. But the corresponding check in tcp_is_sackblock_valid() is the exact opposite. It looks like a typo. Signed-off-by: NZheng Yan <zheng.z.yan@intel.com> Acked-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
commit 946cedcc (tcp: Change possible SYN flooding messages) added a build error if CONFIG_SYN_COOKIES=n Reported-by: NMarkus Trippelsdorf <markus@trippelsdorf.de> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.infradead.org/users/sameo/mfd-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6: mfd: Fix omap-usb-host build failure mfd: Make omap-usb-host TLL mode work again mfd: Set MAX8997 irq pointer mfd: Fix initialisation of tps65910 interrupts mfd: Check for twl4030-madc NULL pointer mfd: Copy the device pointer to the twl4030-madc structure mfd: Rename wm8350 static gpio_set_debounce() mfd: Fix value of WM8994_CONFIGURE_GPIO
-
由 Alex Deucher 提交于
The BO blit code inconsistenly handled the page size. This wasn't an issue on system with 4k pages since the GPU's page size is 4k as well. Switch the driver blit callbacks to take num pages in GPU page units. Fixes lemote mipsel systems using AMD rs780/rs880 chipsets. v2: incorporate suggestions from Michel. Signed-off-by: NAlex Deucher <alexander.deucher@amd.com> Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
cur_pages is the number of pages per loop iteration. Signed-off-by: NAlex Deucher <alexander.deucher@amd.com> Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
git://github.com/davem330/net由 Linus Torvalds 提交于
* git://github.com/davem330/net: (62 commits) ipv6: don't use inetpeer to store metrics for routes. can: ti_hecc: include linux/io.h IRDA: Fix global type conflicts in net/irda/irsysctl.c v2 net: Handle different key sizes between address families in flow cache net: Align AF-specific flowi structs to long ipv4: Fix fib_info->fib_metrics leak caif: fix a potential NULL dereference sctp: deal with multiple COOKIE_ECHO chunks ibmveth: Fix checksum offload failure handling ibmveth: Checksum offload is always disabled ibmveth: Fix issue with DMA mapping failure ibmveth: Fix DMA unmap error pch_gbe: support ML7831 IOH pch_gbe: added the process of FIFO over run error pch_gbe: fixed the issue which receives an unnecessary packet. sfc: Use 64-bit writes for TX push where possible Revert "sfc: Use write-combining to reduce TX latency" and follow-ups bnx2x: Fix ethtool advertisement bnx2x: Fix 578xx link LED bnx2x: Fix XMAC loopback test ...
-
- 18 9月, 2011 2 次提交
-
-
git://git.user.in-berlin.de/s5r6/linux1394由 Linus Torvalds 提交于
* 'fixes' of git://git.user.in-berlin.de/s5r6/linux1394: firewire: ohci: add no MSI quirk for O2Micro controller
-
git://linux-iscsi.org/target-pending由 Linus Torvalds 提交于
* '3.1-rc-fixes' of git://linux-iscsi.org/target-pending: iscsi-target: Fix sendpage breakage with proper padding+DataDigest iovec offsets iscsi-target: Disable markers + remove dangerous local scope array usage target: Skip non hex characters for VPD=0x83 NAA IEEE Registered Extended tcm_fc: Work queue based approach instead of managing own thread and event based mechanism tcm_fc: Invalidation of DDP context for FCoE target in error conditions target: Fix race between multiple invocations of target_qf_do_work()
-
- 17 9月, 2011 18 次提交
-
-
由 Yan, Zheng 提交于
Current IPv6 implementation uses inetpeer to store metrics for routes. The problem of inetpeer is that it doesn't take subnet prefix length in to consideration. If two routes have the same address but different prefix length, they share same inetpeer. So changing metrics of one route also affects the other. The fix is to allocate separate metrics storage for each route. Signed-off-by: NZheng Yan <zheng.z.yan@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicholas Bellinger 提交于
This patch fixes a bug in the iscsit_fe_sendpage_sg() transmit codepath that was originally introduced with the v3.1 iscsi-target merge that incorrectly uses hardcoded cmd->iov_data_count values to determine cmd->iov_data[] offsets for extra outgoing padding and DataDigest payload vectors. This code is obviously incorrect for the DataDigest enabled case with sendpage offload, and this fix ensures correct operation for padding + DataDigest, padding only, and DataDigest only cases. The bug was introduced during a pre-merge change in iscsit_fe_sendpage_sg() to natively use struct scatterlist instead of the legacy v3.0 struct se_mem logic. Cc: Andy Grover <agrover@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
-
由 Daniel Mack 提交于
This fixes a build breakage for OMAP3 boards. Signed-off-by: NDaniel Mack <zonque@gmail.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: netdev@vger.kernel.org Acked-by: NWolfgang Grandegger <wg@grandegger.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andi Kleen 提交于
The externs here didn't agree with the declarations in qos.c. Better would be probably to move this into a header, but since it's common practice to have naked externs with sysctls I left it for now. Cc: samuel@sortiz.org Signed-off-by: NAndi Kleen <ak@linux.intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 dpward 提交于
With the conversion of struct flowi to a union of AF-specific structs, some operations on the flow cache need to account for the exact size of the key. Signed-off-by: NDavid Ward <david.ward@ll.mit.edu> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Ward 提交于
AF-specific flowi structs are now passed to flow_key_compare, which must also be aligned to a long. Signed-off-by: NDavid Ward <david.ward@ll.mit.edu> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yan, Zheng 提交于
Commit 4670994d(net,rcu: convert call_rcu(fc_rport_free_rcu) to kfree_rcu()) introduced a memory leak. This patch reverts it. Signed-off-by: NZheng Yan <zheng.z.yan@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Commit bd30ce4b (caif: Use RCU instead of spin-lock in caif_dev.c) added a potential NULL dereference in case alloc_percpu() fails. caif_device_alloc() can also use GFP_KERNEL instead of GFP_ATOMIC. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> CC: Sjur Brændeland <sjur.brandeland@stericsson.com> Acked-by: NSjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Max Matveev 提交于
Attempt to reduce the number of IP packets emitted in response to single SCTP packet (2e3216cd) introduced a complication - if a packet contains two COOKIE_ECHO chunks and nothing else then SCTP state machine corks the socket while processing first COOKIE_ECHO and then loses the association and forgets to uncork the socket. To deal with the issue add new SCTP command which can be used to set association explictly. Use this new command when processing second COOKIE_ECHO chunk to restore the context for SCTP state machine. Signed-off-by: NMax Matveev <makc@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://github.com/dtor/input由 Linus Torvalds 提交于
* 'for-linus' of git://github.com/dtor/input: Input: wacom - fix touch parsing on newer Bamboos Input: bcm5974 - add MacBookAir4,1 trackpad support Input: wacom - add POINTER and DIRECT device properties Input: adp5588-keys - remove incorrect modalias Input: cm109 - fix checking return value of usb_control_msg Input: wacom - advertise BTN_TOOL_PEN and BTN_STYLUS for PenPartner Input: wacom - remove pressure for touch devices
-
由 Ming Lei 提交于
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 . An O2Micro PCI Express FireWire controller, "FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)" which is a combination device together with an SDHCI controller and some sort of storage controller, misses SBP-2 status writes from an attached FireWire HDD. This problem goes away if MSI is disabled for this FireWire controller. The device reportedly does not require QUIRK_CYCLE_TIMER. Signed-off-by: NMing Lei <ming.lei@canonical.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (amended changelog) Cc: <stable@kernel.org>
-
由 Nicholas Bellinger 提交于
This patch makes iscsi-target explictly disable OFMarker=Yes and IFMarker=yes parameter key usage during iscsi login by setting IFMarkInt_Reject and OFMarkInt_Reject values in iscsi_enforce_integrity_rules() to effectively disable iscsi marker usage. With this patch, an initiator proposer asking to enable either marker parameter keys will be issued a 'No' response, and the target sets OFMarkInt + IFMarkInt parameter key response to 'Irrelevant'. With markers disabled during iscsi login, this patch removes the problematic on-stack local-scope array for marker intervals in iscsit_do_rx_data() + iscsit_do_tx_data(), and other related marker code in iscsi_target_util.c. This fixes a potentional stack smashing scenario with small range markers enabled and a large MRDSL as reported by DanC here: [bug report] target: stack can be smashed http://www.spinics.net/lists/target-devel/msg00453.htmlReported-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
-
由 Nicholas Bellinger 提交于
This patch adds target_parse_naa_6h_vendor_specific() to address a bug where the conversion of PRODUCT SERIAL NUMBER to use hex2bin() in target_emulate_evpd_83() was not doing proper isxdigit() checking. This conversion of the vpd_unit_serial configifs attribute is done while generating a VPD=0x83 NAA IEEE Registered Extended DESIGNATOR format's 100 bits of unique VENDOR SPECIFIC IDENTIFIER + VENDOR SPECIFIC IDENTIFIER EXTENSION area. This patch allows vpd_unit_serial (VPD=0x80) and the T10 Vendor ID DESIGNATOR format (VPD=0x83) to continue to use free-form variable length ASCII values, and now skips any non hex characters for fixed length NAA IEEE Registered Extended DESIGNATOR format (VPD=0x83) requring the binary conversion. This was originally reported by Martin after the v3.1-rc1 change to use hex2bin() in commit 11650b85 where the use of non hex characters in vpd_unit_serial generated different values than the original v3.0 internal hex -> binary code. This v3.1 change caused a problem with filesystems who write a NAA DESIGNATOR onto it's ondisk metadata, and this patch will (again) change existing values to ensure that non hex characters are not included in the fixed length NAA DESIGNATOR. Note this patch still expects vpd_unit_serial to be set via existing userspace methods of uuid generation, and does not do strict formatting via configfs input. The original bug report and thread can be found here: NAA breakage http://www.spinics.net/lists/target-devel/msg00477.html The v3.1-rc1 formatting of VPD=0x83 w/o this patch: VPD INQUIRY: Device Identification page Designation descriptor number 1, descriptor length: 20 designator_type: NAA, code_set: Binary associated with the addressed logical unit NAA 6, IEEE Company_id: 0x1405 Vendor Specific Identifier: 0xffde35ebf Vendor Specific Identifier Extension: 0x3092f498ffa820f9 [0x6001405ffde35ebf3092f498ffa820f9] Designation descriptor number 2, descriptor length: 56 designator_type: T10 vendor identification, code_set: ASCII associated with the addressed logical unit vendor id: LIO-ORG vendor specific: IBLOCK:ffde35ec-3092-4980-a820-917636ca54f1 The v3.1-final formatting of VPD=0x83 w/ this patch: VPD INQUIRY: Device Identification page Designation descriptor number 1, descriptor length: 20 designator_type: NAA, code_set: Binary associated with the addressed logical unit NAA 6, IEEE Company_id: 0x1405 Vendor Specific Identifier: 0xffde35ec3 Vendor Specific Identifier Extension: 0x924980a82091763 [0x6001405ffde35ec30924980a82091763] Designation descriptor number 2, descriptor length: 56 designator_type: T10 vendor identification, code_set: ASCII associated with the addressed logical unit vendor id: LIO-ORG vendor specific: IBLOCK:ffde35ec-3092-4980-a820-917636ca54f1 (v2: Fix parsing code to dereference + check for string terminator instead of null pointer to ensure a zeroed payload for vpd_unit_serial less than 100 bits of NAA DESIGNATOR VENDOR SPECIFIC area. Also, remove the unnecessary bitwise assignment) Reported-by: NMartin Svec <martin.svec@zoner.cz> Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
-
由 Anton Blanchard 提交于
Fix a number of issues in ibmveth_set_csum_offload: - set_attr6 and clr_attr6 may be used uninitialised - We store the result of the IPV4 checksum change in ret but overwrite it in a couple of places before checking it again later. Add ret4 to make it obvious what we are doing. - We weren't clearing the NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM flags if the enable of that hypervisor feature failed. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Anton Blanchard 提交于
Commit b9367bf3 (net: ibmveth: convert to hw_features) reversed a check in ibmveth_set_csum_offload that results in checksum offload never being enabled. Signed-off-by: NAnton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # 3.0+ Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Anton Blanchard 提交于
descs[].fields.address is 32bit which truncates any dma mapping errors so dma_mapping_error() fails to catch it. Use a dma_addr_t to do the comparison. With this patch I was able to transfer many gigabytes of data with IOMMU fault injection set at 10% probability. Signed-off-by: NAnton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # v2.6.37+ Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Brian King 提交于
Commit 6e8ab30e (ibmveth: Add scatter-gather support) introduced a DMA mapping API inconsistency resulting in dma_unmap_page getting called on memory mapped via dma_map_single. This was seen when CONFIG_DMA_API_DEBUG was enabled. Fix up this API usage inconsistency. Signed-off-by: NBrian King <brking@linux.vnet.ibm.com> Acked-by: NAnton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # v2.6.37+ Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://oss.oracle.com/git/kwilk/xen由 Linus Torvalds 提交于
* 'stable/bug.fixes' of git://oss.oracle.com/git/kwilk/xen: xen/i386: follow-up to "replace order-based range checking of M2P table by linear one" xen/irq: Alter the locking to use a mutex instead of a spinlock. xen/e820: if there is no dom0_mem=, don't tweak extra_pages. xen: disable PV spinlocks on HVM
-
- 16 9月, 2011 6 次提交
-
-
由 Christoph Hellwig 提交于
Problem: Changed from wake_up_interruptible -> wake_up_process and wait_event_interruptible-> schedule_timeout_interruptible broke the FCoE target. Earlier approach of wake_up_interruptible was also looking at 'queue_cnt' which is not necessary, because it increment of 'queue_cnt' with wake_up_inetrriptible / waker_up_process introduces race condition. Fix: Instead of fixing the code which used wake_up_process and remove 'queue_cnt', using work_queue based approach is cleaner and acheives same result. As well, work queue based approach has less programming overhead and OS manages threads which processes work queues. This patch is developed by Christoph Hellwig and reviwed+validated by Kiran Patil. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NKiran Patil <kiran.patil@intel.com> Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
-
由 Kiran Patil 提交于
Problem: HW DDP context wasn;t invalidated in case of ABORTS, etc... This leads to the problem where memory pages which are used for DDP as user descriptor could get reused for some other purpose (such as to satisfy new memory allocation request either by kernel or user mode threads) and since HW DDP context was not invalidated, HW continue to write to those pages, hence causing memory corruption. Fix: Either on incoming ABORTS or due to exchange time out, allowed the target to cleanup HW DDP context if it was setup for respective ft_cmd. Added new function to perform this cleanup, furthur it can be enhanced for other cleanup activity. Additinal Notes: To avoid calling ddp_done from multiple places, composed the functionality in helper function "ft_invl_hw_context" and it is being called from multiple places. Cleaned up code in function "ft_recv_write_data" w.r.t DDP. Signed-off-by: NKiran Patil <kiran.patil@intel.com> Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
-
由 Roland Dreier 提交于
When work is scheduled with schedule_work(), the work can end up running on multiple CPUs at the same time -- this happens if the work is already running on one CPU and schedule_work() is called on another CPU. This leads to list corruption with target_qf_do_work(), which is roughly doing: spin_lock(...); list_for_each_entry_safe(...) { list_del(...); spin_unlock(...); // do stuff spin_lock(...); } With multiple CPUs running this code, one CPU can end up deleting the list entry that the other CPU is about to work on. Fix this by splicing the list entries onto a local list and then operating on that in the work function. This way, each invocation of target_qf_do_work() operates on its own local list and so multiple invocations don't corrupt each other's list. This also avoids dropping and reacquiring the lock for each list entry. Signed-off-by: NRoland Dreier <roland@purestorage.com> Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
-
git://github.com/tiwai/sound由 Linus Torvalds 提交于
* 'for-linus' of git://github.com/tiwai/sound: ALSA: pcm - fix race condition in wait_for_avail() ALSA: HDA: Cirrus - fix "Surround Speaker" volume control name ALSA: hda - Terminate the recursive connection search properly ASoC: Fix trivial build regression in Kirkwood I2S ASoC: Blackfin: bf5xx-ad193x: Fix codec device name ASoC: Fix reporting of partial jack updates ASoC: imx: Fix build warning of unused 'card' variable ASoC: Fix register cache sync register_writable WARN_ONs ASoC: snd_soc_codec_{readable,writable}_register change default to true ASoC: soc-dapm: Fix parameter comment for snd_soc_dapm_free MAINTAINERS: Add some missed Wolfson files ASoC: MPC5200: replace of_device with platform_device
-
由 David S. Miller 提交于
-
由 Toshiharu Okada 提交于
Support new device OKI SEMICONDUCTOR ML7831 IOH(Input/Output Hub) ML7831 is for general purpose use. ML7831 is companion chip for Intel Atom E6xx series. ML7831 is completely compatible for Intel EG20T PCH. Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-