提交 ed14e1c2 编写于 作者: D Devin Heitmueller 提交者: Mauro Carvalho Chehab

V4L/DVB (10119): em28xx: fix corrupted XCLK value

Correct problem introduced during the board refactoring where the XCLK
frequency would get zero'd out.  The sequence of events was as follows:

em28xx_pre_card_setup() called em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration
em28xx_pre_card_setup() would set the dev->board.xclk if not set
em28xx_pre_card_setup() would set the XCLK register based on dev->board.xclk
...
em28xx_card_setup() would call em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration (clearing out
 value of dev->board.xclk set in em28xx_pre_card_setup)
...
em28xx_audio_analog_set() sets the XCLK register based on dev->board.xclk
 (which now contains zero)

The change sets the default XCLK and I2C Clock fields in the board definition
inside of em28xx_set_model() so that subsequent calls do not cause the
values to be overwritten.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
上级 60b4bde4
......@@ -1403,6 +1403,17 @@ EXPORT_SYMBOL_GPL(em28xx_tuner_callback);
static void inline em28xx_set_model(struct em28xx *dev)
{
memcpy(&dev->board, &em28xx_boards[dev->model], sizeof(dev->board));
/* Those are the default values for the majority of boards
Use those values if not specified otherwise at boards entry
*/
if (!dev->board.xclk)
dev->board.xclk = EM28XX_XCLK_IR_RC5_MODE |
EM28XX_XCLK_FREQUENCY_12MHZ;
if (!dev->board.i2c_speed)
dev->board.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_100_KHZ;
}
/* Since em28xx_pre_card_setup() requires a proper dev->model,
......@@ -1464,17 +1475,8 @@ void em28xx_pre_card_setup(struct em28xx *dev)
if (rc >= 0)
dev->reg_gpo = rc;
/* Those are the default values for the majority of boards
Use those values if not specified otherwise at boards entry
*/
if (!dev->board.xclk)
dev->board.xclk = EM28XX_XCLK_IR_RC5_MODE |
EM28XX_XCLK_FREQUENCY_12MHZ;
if (!dev->board.i2c_speed)
dev->board.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_100_KHZ;
/* Set the initial XCLK and I2C clock values based on the board
definition */
em28xx_write_reg(dev, EM28XX_R0F_XCLK, dev->board.xclk & 0x7f);
em28xx_write_reg(dev, EM28XX_R06_I2C_CLK, dev->board.i2c_speed);
msleep(50);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册