提交 e0aac5a2 编写于 作者: A Auke Kok 提交者: Jeff Garzik

e1000: FIX: be ready for incoming irq at pci_request_irq

DEBUG_SHIRQ code exposed that e1000 was not ready for incoming interrupts
after having called pci_request_irq. This obviously requires us to finish
our software setup which assigns the irq handler before we request the
irq.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
上级 de46c337
......@@ -522,14 +522,15 @@ e1000_release_manageability(struct e1000_adapter *adapter)
}
}
int
e1000_up(struct e1000_adapter *adapter)
/**
* e1000_configure - configure the hardware for RX and TX
* @adapter = private board structure
**/
static void e1000_configure(struct e1000_adapter *adapter)
{
struct net_device *netdev = adapter->netdev;
int i;
/* hardware has been reset, we need to reload some things */
e1000_set_multi(netdev);
e1000_restore_vlan(adapter);
......@@ -548,14 +549,20 @@ e1000_up(struct e1000_adapter *adapter)
}
adapter->tx_queue_len = netdev->tx_queue_len;
}
int e1000_up(struct e1000_adapter *adapter)
{
/* hardware has been reset, we need to reload some things */
e1000_configure(adapter);
clear_bit(__E1000_DOWN, &adapter->flags);
#ifdef CONFIG_E1000_NAPI
netif_poll_enable(netdev);
netif_poll_enable(adapter->netdev);
#endif
e1000_irq_enable(adapter);
clear_bit(__E1000_DOWN, &adapter->flags);
/* fire a link change interrupt to start the watchdog */
E1000_WRITE_REG(&adapter->hw, ICS, E1000_ICS_LSC);
return 0;
......@@ -640,15 +647,15 @@ e1000_down(struct e1000_adapter *adapter)
* reschedule our watchdog timer */
set_bit(__E1000_DOWN, &adapter->flags);
#ifdef CONFIG_E1000_NAPI
netif_poll_disable(netdev);
#endif
e1000_irq_disable(adapter);
del_timer_sync(&adapter->tx_fifo_stall_timer);
del_timer_sync(&adapter->watchdog_timer);
del_timer_sync(&adapter->phy_info_timer);
#ifdef CONFIG_E1000_NAPI
netif_poll_disable(netdev);
#endif
netdev->tx_queue_len = adapter->tx_queue_len;
adapter->link_speed = 0;
adapter->link_duplex = 0;
......@@ -1410,21 +1417,17 @@ e1000_open(struct net_device *netdev)
return -EBUSY;
/* allocate transmit descriptors */
if ((err = e1000_setup_all_tx_resources(adapter)))
err = e1000_setup_all_tx_resources(adapter);
if (err)
goto err_setup_tx;
/* allocate receive descriptors */
if ((err = e1000_setup_all_rx_resources(adapter)))
goto err_setup_rx;
err = e1000_request_irq(adapter);
err = e1000_setup_all_rx_resources(adapter);
if (err)
goto err_req_irq;
goto err_setup_rx;
e1000_power_up_phy(adapter);
if ((err = e1000_up(adapter)))
goto err_up;
adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
if ((adapter->hw.mng_cookie.status &
E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) {
......@@ -1437,12 +1440,33 @@ e1000_open(struct net_device *netdev)
e1000_check_mng_mode(&adapter->hw))
e1000_get_hw_control(adapter);
/* before we allocate an interrupt, we must be ready to handle it.
* Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
* as soon as we call pci_request_irq, so we have to setup our
* clean_rx handler before we do so. */
e1000_configure(adapter);
err = e1000_request_irq(adapter);
if (err)
goto err_req_irq;
/* From here on the code is the same as e1000_up() */
clear_bit(__E1000_DOWN, &adapter->flags);
#ifdef CONFIG_E1000_NAPI
netif_poll_enable(netdev);
#endif
e1000_irq_enable(adapter);
/* fire a link status change interrupt to start the watchdog */
E1000_WRITE_REG(&adapter->hw, ICS, E1000_ICS_LSC);
return E1000_SUCCESS;
err_up:
e1000_power_down_phy(adapter);
e1000_free_irq(adapter);
err_req_irq:
e1000_release_hw_control(adapter);
e1000_power_down_phy(adapter);
e1000_free_all_rx_resources(adapter);
err_setup_rx:
e1000_free_all_tx_resources(adapter);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册