提交 a2202aa2 编写于 作者: Y Yong Wang 提交者: Ingo Molnar

x86: Under BIOS control, restore AP's APIC_LVTTHMR to the BSP value

On platforms where the BIOS handles the thermal monitor interrupt,
APIC_LVTTHMR on each logical CPU is programmed to generate a SMI
and OS must not touch it.

Unfortunately AP bringup sequence using INIT-SIPI-SIPI clears all
the LVT entries except the mask bit. Essentially this results in
all LVT entries including the thermal monitoring interrupt set
to masked (clearing the bios programmed value for APIC_LVTTHMR).

And this leads to kernel take over the thermal monitoring
interrupt on AP's but not on BSP (leaving the bios programmed
value only on BSP).

As a result of this, we have seen system hangs when the thermal
monitoring interrupt is generated.

Fix this by reading the initial value of thermal LVT entry on
BSP and if bios has taken over the control, then program the
same value on all AP's and leave the thermal monitoring
interrupt control on all the logical cpu's to the bios.
Signed-off-by: NYong Wang <yong.y.wang@intel.com>
Reviewed-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20091110013824.GA24940@ywang-moblin2.bj.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
上级 b33a6363
......@@ -120,8 +120,10 @@ extern int mce_disabled;
extern int mce_p5_enabled;
#ifdef CONFIG_X86_MCE
int mcheck_init(void);
void mcheck_cpu_init(struct cpuinfo_x86 *c);
#else
static inline int mcheck_init(void) { return 0; }
static inline void mcheck_cpu_init(struct cpuinfo_x86 *c) {}
#endif
......@@ -215,5 +217,12 @@ extern void (*threshold_cpu_callback)(unsigned long action, unsigned int cpu);
void intel_init_thermal(struct cpuinfo_x86 *c);
void mce_log_therm_throt_event(__u64 status);
#ifdef CONFIG_X86_THERMAL_VECTOR
extern void mcheck_intel_therm_init(void);
#else
static inline void mcheck_intel_therm_init(void) { }
#endif
#endif /* __KERNEL__ */
#endif /* _ASM_X86_MCE_H */
......@@ -837,10 +837,8 @@ static void __cpuinit identify_cpu(struct cpuinfo_x86 *c)
boot_cpu_data.x86_capability[i] &= c->x86_capability[i];
}
#ifdef CONFIG_X86_MCE
/* Init Machine Check Exception if available. */
mcheck_cpu_init(c);
#endif
select_idle_routine(c);
......
......@@ -1655,13 +1655,14 @@ static int __init mcheck_enable(char *str)
}
__setup("mce", mcheck_enable);
static int __init mcheck_init(void)
int __init mcheck_init(void)
{
atomic_notifier_chain_register(&x86_mce_decoder_chain, &mce_dec_nb);
mcheck_intel_therm_init();
return 0;
}
early_initcall(mcheck_init);
/*
* Sysfs support
......
......@@ -49,6 +49,8 @@ static DEFINE_PER_CPU(struct thermal_state, thermal_state);
static atomic_t therm_throt_en = ATOMIC_INIT(0);
static u32 lvtthmr_init __read_mostly;
#ifdef CONFIG_SYSFS
#define define_therm_throt_sysdev_one_ro(_name) \
static SYSDEV_ATTR(_name, 0444, therm_throt_sysdev_show_##_name, NULL)
......@@ -254,6 +256,18 @@ asmlinkage void smp_thermal_interrupt(struct pt_regs *regs)
ack_APIC_irq();
}
void mcheck_intel_therm_init(void)
{
/*
* This function is only called on boot CPU. Save the init thermal
* LVT value on BSP and use that value to restore APs' thermal LVT
* entry BIOS programmed later
*/
if (cpu_has(&boot_cpu_data, X86_FEATURE_ACPI) &&
cpu_has(&boot_cpu_data, X86_FEATURE_ACC))
lvtthmr_init = apic_read(APIC_LVTTHMR);
}
void intel_init_thermal(struct cpuinfo_x86 *c)
{
unsigned int cpu = smp_processor_id();
......@@ -270,7 +284,20 @@ void intel_init_thermal(struct cpuinfo_x86 *c)
* since it might be delivered via SMI already:
*/
rdmsr(MSR_IA32_MISC_ENABLE, l, h);
h = apic_read(APIC_LVTTHMR);
/*
* The initial value of thermal LVT entries on all APs always reads
* 0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
* sequence to them and LVT registers are reset to 0s except for
* the mask bits which are set to 1s when APs receive INIT IPI.
* Always restore the value that BIOS has programmed on AP based on
* BSP's info we saved since BIOS is always setting the same value
* for all threads/cores
*/
apic_write(APIC_LVTTHMR, lvtthmr_init);
h = lvtthmr_init;
if ((l & MSR_IA32_MISC_ENABLE_TM1) && (h & APIC_DM_SMI)) {
printk(KERN_DEBUG
"CPU%d: Thermal monitoring handled by SMI\n", cpu);
......
......@@ -109,6 +109,7 @@
#ifdef CONFIG_X86_64
#include <asm/numa_64.h>
#endif
#include <asm/mce.h>
/*
* end_pfn only includes RAM, while max_pfn_mapped includes all e820 entries.
......@@ -1024,6 +1025,8 @@ void __init setup_arch(char **cmdline_p)
#endif
#endif
x86_init.oem.banner();
mcheck_init();
}
#ifdef CONFIG_X86_32
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册