/******************** (C) COPYRIGHT 2008 STMicroelectronics ******************** * File Name : sdcard.h * Author : MCD Application Team * Version : V2.0.3 * Date : 09/22/2008 * Description : This file contains all the functions prototypes for the * SD Card driver firmware library. ******************************************************************************** * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME. * AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT, * INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE * CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING * INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. *******************************************************************************/ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __SDCARD_H #define __SDCARD_H /* Includes ------------------------------------------------------------------*/ #include "stm32f10x_lib.h" /* Exported types ------------------------------------------------------------*/ typedef enum { /* SDIO specific error defines */ SD_CMD_CRC_FAIL = (1), /* Command response received (but CRC check failed) */ SD_DATA_CRC_FAIL = (2), /* Data bock sent/received (CRC check Failed) */ SD_CMD_RSP_TIMEOUT = (3), /* Command response timeout */ SD_DATA_TIMEOUT = (4), /* Data time out */ SD_TX_UNDERRUN = (5), /* Transmit FIFO under-run */ SD_RX_OVERRUN = (6), /* Receive FIFO over-run */ SD_START_BIT_ERR = (7), /* Start bit not detected on all data signals in widE bus mode */ SD_CMD_OUT_OF_RANGE = (8), /* CMD's argument was out of range.*/ SD_ADDR_MISALIGNED = (9), /* Misaligned address */ SD_BLOCK_LEN_ERR = (10), /* Transferred block length is not allowed for the card or the number of transferred bytes does not match the block length */ SD_ERASE_SEQ_ERR = (11), /* An error in the sequence of erase command occurs.*/ SD_BAD_ERASE_PARAM = (12), /* An Invalid selection for erase groups */ SD_WRITE_PROT_VIOLATION = (13), /* Attempt to program a write protect block */ SD_LOCK_UNLOCK_FAILED = (14), /* Sequence or password error has been detected in unlock command or if there was an attempt to access a locked card */ SD_COM_CRC_FAILED = (15), /* CRC check of the previous command failed */ SD_ILLEGAL_CMD = (16), /* Command is not legal for the card state */ SD_CARD_ECC_FAILED = (17), /* Card internal ECC was applied but failed to correct the data */ SD_CC_ERROR = (18), /* Internal card controller error */ SD_GENERAL_UNKNOWN_ERROR = (19), /* General or Unknown error */ SD_STREAM_READ_UNDERRUN = (20), /* The card could not sustain data transfer in stream read operation. */ SD_STREAM_WRITE_OVERRUN = (21), /* The card could not sustain data programming in stream mode */ SD_CID_CSD_OVERWRITE = (22), /* CID/CSD overwrite error */ SD_WP_ERASE_SKIP = (23), /* only partial address space was erased */ SD_CARD_ECC_DISABLED = (24), /* Command has been executed without using internal ECC */ SD_ERASE_RESET = (25), /* Erase sequence was cleared before executing because an out of erase sequence command was received */ SD_AKE_SEQ_ERROR = (26), /* Error in sequence of authentication. */ SD_INVALID_VOLTRANGE = (27), SD_ADDR_OUT_OF_RANGE = (28), SD_SWITCH_ERROR = (29), SD_SDIO_DISABLED = (30), SD_SDIO_FUNCTION_BUSY = (31), SD_SDIO_FUNCTION_FAILED = (32), SD_SDIO_UNKNOWN_FUNCTION = (33), /* Standard error defines */ SD_INTERNAL_ERROR, SD_NOT_CONFIGURED, SD_REQUEST_PENDING, SD_REQUEST_NOT_APPLICABLE, SD_INVALID_PARAMETER, SD_UNSUPPORTED_FEATURE, SD_UNSUPPORTED_HW, SD_ERROR, SD_OK, } SD_Error; /* SDIO Commands Index */ #define SDIO_GO_IDLE_STATE ((u8)0) #define SDIO_SEND_OP_COND ((u8)1) #define SDIO_ALL_SEND_CID ((u8)2) #define SDIO_SET_REL_ADDR ((u8)3) /* SDIO_SEND_REL_ADDR for SD Card */ #define SDIO_SET_DSR ((u8)4) #define SDIO_SDIO_SEN_OP_COND ((u8)5) #define SDIO_HS_SWITCH ((u8)6) #define SDIO_SEL_DESEL_CARD ((u8)7) #define SDIO_HS_SEND_EXT_CSD ((u8)8) #define SDIO_SEND_CSD ((u8)9) #define SDIO_SEND_CID ((u8)10) #define SDIO_READ_DAT_UNTIL_STOP ((u8)11) /* SD Card doesn't support it */ #define SDIO_STOP_TRANSMISSION ((u8)12) #define SDIO_SEND_STATUS ((u8)13) #define SDIO_HS_BUSTEST_READ ((u8)14) #define SDIO_GO_INACTIVE_STATE ((u8)15) #define SDIO_SET_BLOCKLEN ((u8)16) #define SDIO_READ_SINGLE_BLOCK ((u8)17) #define SDIO_READ_MULT_BLOCK ((u8)18) #define SDIO_HS_BUSTEST_WRITE ((u8)19) #define SDIO_WRITE_DAT_UNTIL_STOP ((u8)20) /* SD Card doesn't support it */ #define SDIO_SET_BLOCK_COUNT ((u8)23) /* SD Card doesn't support it */ #define SDIO_WRITE_SINGLE_BLOCK ((u8)24) #define SDIO_WRITE_MULT_BLOCK ((u8)25) #define SDIO_PROG_CID ((u8)26) /* reserved for manufacturers */ #define SDIO_PROG_CSD ((u8)27) #define SDIO_SET_WRITE_PROT ((u8)28) #define SDIO_CLR_WRITE_PROT ((u8)29) #define SDIO_SEND_WRITE_PROT ((u8)30) #define SDIO_SD_ERASE_GRP_START ((u8)32) /* To set the address of the first write block to be erased. (For SD card only) */ #define SDIO_SD_ERASE_GRP_END ((u8)33) /* To set the address of the last write block of the continuous range to be erased. (For SD card only) */ #define SDIO_ERASE_GRP_START ((u8)35) /* To set the address of the first write block to be erased. (For MMC card only spec 3.31) */ #define SDIO_ERASE_GRP_END ((u8)36) /* To set the address of the last write block of the continuous range to be erased. (For MMC card only spec 3.31) */ #define SDIO_ERASE ((u8)38) #define SDIO_FAST_IO ((u8)39) /* SD Card doesn't support it */ #define SDIO_GO_IRQ_STATE ((u8)40) /* SD Card doesn't support it */ #define SDIO_LOCK_UNLOCK ((u8)42) #define SDIO_APP_CMD ((u8)55) #define SDIO_GEN_CMD ((u8)56) #define SDIO_NO_CMD ((u8)64) /* Following commands are SD Card Specific commands. SDIO_APP_CMD should be sent before sending these commands. */ #define SDIO_APP_SD_SET_BUSWIDTH ((u8)6) /* For SD Card only */ #define SDIO_SD_APP_STAUS ((u8)13) /* For SD Card only */ #define SDIO_SD_APP_SEND_NUM_WRITE_BLOCKS ((u8)22) /* For SD Card only */ #define SDIO_SD_APP_OP_COND ((u8)41) /* For SD Card only */ #define SDIO_SD_APP_SET_CLR_CARD_DETECT ((u8)42) /* For SD Card only */ #define SDIO_SD_APP_SEND_SCR ((u8)51) /* For SD Card only */ #define SDIO_SDIO_RW_DIRECT ((u8)52) /* For SD I/O Card only */ #define SDIO_SDIO_RW_EXTENDED ((u8)53) /* For SD I/O Card only */ /* Following commands are SD Card Specific security commands. SDIO_APP_CMD should be sent before sending these commands. */ #define SDIO_SD_APP_GET_MKB ((u8)43) /* For SD Card only */ #define SDIO_SD_APP_GET_MID ((u8)44) /* For SD Card only */ #define SDIO_SD_APP_SET_CER_RN1 ((u8)45) /* For SD Card only */ #define SDIO_SD_APP_GET_CER_RN2 ((u8)46) /* For SD Card only */ #define SDIO_SD_APP_SET_CER_RES2 ((u8)47) /* For SD Card only */ #define SDIO_SD_APP_GET_CER_RES1 ((u8)48) /* For SD Card only */ #define SDIO_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((u8)18) /* For SD Card only */ #define SDIO_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((u8)25) /* For SD Card only */ #define SDIO_SD_APP_SECURE_ERASE ((u8)38) /* For SD Card only */ #define SDIO_SD_APP_CHANGE_SECURE_AREA ((u8)49) /* For SD Card only */ #define SDIO_SD_APP_SECURE_WRITE_MKB ((u8)48) /* For SD Card only */ typedef enum { SD_NO_TRANSFER = 0, SD_TRANSFER_IN_PROGRESS } SDTransferState; typedef struct { u16 TransferredBytes; SD_Error TransferError; u8 padding; } SDLastTransferInfo; typedef struct /* Card Specific Data */ { vu8 CSDStruct; /* CSD structure */ vu8 SysSpecVersion; /* System specification version */ vu8 Reserved1; /* Reserved */ vu8 TAAC; /* Data read access-time 1 */ vu8 NSAC; /* Data read access-time 2 in CLK cycles */ vu8 MaxBusClkFrec; /* Max. bus clock frequency */ vu16 CardComdClasses; /* Card command classes */ vu8 RdBlockLen; /* Max. read data block length */ vu8 PartBlockRead; /* Partial blocks for read allowed */ vu8 WrBlockMisalign; /* Write block misalignment */ vu8 RdBlockMisalign; /* Read block misalignment */ vu8 DSRImpl; /* DSR implemented */ vu8 Reserved2; /* Reserved */ vu32 DeviceSize; /* Device Size */ vu8 MaxRdCurrentVDDMin; /* Max. read current @ VDD min */ vu8 MaxRdCurrentVDDMax; /* Max. read current @ VDD max */ vu8 MaxWrCurrentVDDMin; /* Max. write current @ VDD min */ vu8 MaxWrCurrentVDDMax; /* Max. write current @ VDD max */ vu8 DeviceSizeMul; /* Device size multiplier */ vu8 EraseGrSize; /* Erase group size */ vu8 EraseGrMul; /* Erase group size multiplier */ vu8 WrProtectGrSize; /* Write protect group size */ vu8 WrProtectGrEnable; /* Write protect group enable */ vu8 ManDeflECC; /* Manufacturer default ECC */ vu8 WrSpeedFact; /* Write speed factor */ vu8 MaxWrBlockLen; /* Max. write data block length */ vu8 WriteBlockPaPartial; /* Partial blocks for write allowed */ vu8 Reserved3; /* Reserded */ vu8 ContentProtectAppli; /* Content protection application */ vu8 FileFormatGrouop; /* File format group */ vu8 CopyFlag; /* Copy flag (OTP) */ vu8 PermWrProtect; /* Permanent write protection */ vu8 TempWrProtect; /* Temporary write protection */ vu8 FileFormat; /* File Format */ vu8 ECC; /* ECC code */ vu8 CSD_CRC; /* CSD CRC */ vu8 Reserved4; /* always 1*/ } SD_CSD; typedef struct /*Card Identification Data*/ { vu8 ManufacturerID; /* ManufacturerID */ vu16 OEM_AppliID; /* OEM/Application ID */ vu32 ProdName1; /* Product Name part1 */ vu8 ProdName2; /* Product Name part2*/ vu8 ProdRev; /* Product Revision */ vu32 ProdSN; /* Product Serial Number */ vu8 Reserved1; /* Reserved1 */ vu16 ManufactDate; /* Manufacturing Date */ vu8 CID_CRC; /* CID CRC */ vu8 Reserved2; /* always 1 */ } SD_CID; typedef struct { SD_CSD SD_csd; SD_CID SD_cid; u32 CardCapacity; /* Card Capacity */ u32 CardBlockSize; /* Card Block Size */ u16 RCA; u8 CardType; } SD_CardInfo; /* Exported constants --------------------------------------------------------*/ #define SD_DMA_MODE ((u32)0x00000000) #define SD_INTERRUPT_MODE ((u32)0x00000001) #define SD_POLLING_MODE ((u32)0x00000002) /* Supported Memory Cards */ #define SDIO_STD_CAPACITY_SD_CARD_V1_1 ((u32)0x0) #define SDIO_STD_CAPACITY_SD_CARD_V2_0 ((u32)0x1) #define SDIO_HIGH_CAPACITY_SD_CARD ((u32)0x2) #define SDIO_MULTIMEDIA_CARD ((u32)0x3) #define SDIO_SECURE_DIGITAL_IO_CARD ((u32)0x4) #define SDIO_HIGH_SPEED_MULTIMEDIA_CARD ((u32)0x5) #define SDIO_SECURE_DIGITAL_IO_COMBO_CARD ((u32)0x6) #define SDIO_HIGH_CAPACITY_MMC_CARD ((u32)0x7) /* Exported macro ------------------------------------------------------------*/ /* Exported functions ------------------------------------------------------- */ SD_Error SD_Init(void); SD_Error SD_PowerON(void); SD_Error SD_PowerOFF(void); SD_Error SD_InitializeCards(void); SD_Error SD_GetCardInfo(SD_CardInfo *cardinfo); SD_Error SD_EnableWideBusOperation(u32 WideMode); SD_Error SD_SetDeviceMode(u32 Mode); SD_Error SD_SelectDeselect(u32 addr); SD_Error SD_ReadBlock(u32 addr, u32 *readbuff, u16 BlockSize); SD_Error SD_ReadMultiBlocks(u32 addr, u32 *readbuff, u16 BlockSize, u32 NumberOfBlocks); SD_Error SD_WriteBlock(u32 addr, u32 *writebuff, u16 BlockSize); SD_Error SD_WriteMultiBlocks(u32 addr, u32 *writebuff, u16 BlockSize, u32 NumberOfBlocks); SDTransferState SD_GetTransferState(void); SD_Error SD_StopTransfer(void); SD_Error SD_Erase(u32 startaddr, u32 endaddr); SD_Error SD_SendStatus(u32 *pcardstatus); SD_Error SD_SendSDStatus(u32 *psdstatus); SD_Error SD_ProcessIRQSrc(void); #endif /* __SDCARD_H */ /******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE****/