menu "Hardware Drivers Config"

    menu "On-chip Peripheral Drivers"
        source "$BSP_DIR/../libraries/m480/rtt_port/Kconfig"
    endmenu

    menu "On-board Peripheral Drivers"

        config BSP_USING_NULINKME
            bool "Enable UART0 for RTT Console(uart0)"
            select BSP_USING_UART
            select BSP_USING_UART0
            default y

        config BOARD_USING_IP101GR
            bool "Enable ethernet phy supporting(over emac/mdio)"
            select BSP_USING_EMAC
            default n

        config BOARD_USING_ESP8266
            bool "ESP8266 Wi-Fi module supporting(over uart1)"
            select BSP_USING_UART
            select BSP_USING_UART1
            select BSP_USING_UART1_RX_DMA
            select BSP_USING_UART1_TX_DMA
            select PKG_USING_AT_DEVICE
            select AT_DEVICE_USING_ESP8266
            select AT_DEVICE_ESP8266_INIT_ASYN
            default n

        config BOARD_USING_BMX055
            bool "BMX055 9-axis sensor(over i2c2)"
            select NU_PKG_USING_BMX055
            select BSP_USING_I2C2
            default n

        config BOARD_USING_NAU88L25
            bool "NAU88L25 Audio Codec supporting(over i2s, i2c2)"
            select NU_PKG_USING_NAU88L25
            select BSP_USING_I2C2
            select BSP_USING_I2S
            select BSP_USING_I2S0
            default n

        config BOARD_USING_STORAGE_SDCARD
            bool "SDCARD supporting(over sdh0)"
            select BSP_USING_SDH
            select BSP_USING_SDH0
            default n

        config BOARD_USING_STORAGE_SPIFLASH
            bool "SPIFLASH supporting(over qspi0)"
            select BSP_USING_QSPI
            select BSP_USING_QSPI0
            default y

        config BOARD_USING_USB_D_H
            bool "Enable USB Device or Host function"
            help
                Choose this option if you need USB function.

        if BOARD_USING_USB_D_H
            choice
                prompt "Select FS/HS USB Ports"

                config BOARD_USING_HSUSBD
                    select BSP_USING_HSUSBD
                    bool "Enable HSUSBD(over USB2.0)"
                    help
                        Choose this option if you need HSUSBD function mode.

                config BOARD_USING_HSUSBD_USBH
                    select BSP_USING_USBH
                    select BSP_USING_HSUSBD
                    bool "Enable HSUSBD(over USB2.0) and USBH(over USB1.1)"
                    help
                        Choose this option if you need HSUSBD and USBH function mode at the same time.

                config BOARD_USING_HSUSBH
                    select BSP_USING_HSUSBH
                    bool "Enable HSUSBH(over USB2.0)"
                    help
                        Choose this option if you need HSUSBH function mode.

                config BOARD_USING_HSUSBH_USBD
                    select BSP_USING_HSUSBH
                    select BSP_USING_USBD
                    bool "Enable HSUSBH(over USB2.0) and USBD(over USB1.1)"
                    help
                        Choose this option if you need HSUSBH and USBD function mode at the same time.

                config BOARD_USING_HSOTG
                    select BSP_USING_HSOTG
                    bool "Enable HSOTG(over USB2.0)"
                    help
                        Choose this option if you need HSOTG function mode.
            endchoice
        endif

    endmenu

    menu "Board extended module drivers"

        config BOARD_USING_MAX31875
            bool "MAX31875 Temperature sensor(over i2c1)"
            select NU_PKG_USING_MAX31875
            select BSP_USING_I2C1
            default n

        config BOARD_USING_LCD_ILI9341
            bool "LCD ILI9341 (over spi2)"
            select NU_PKG_USING_ILI9341
            select NU_PKG_USING_ILI9341_SPI
            select BSP_USING_SPI2
            default n

        if BOARD_USING_LCD_ILI9341

            config BOARD_USING_ILI9341_PIN_BACKLIGHT
            int "Specify the pin index of backlight pin index"
                range 0 127
                default 69

            config BOARD_USING_ILI9341_PIN_RESET
            int "Specify the pin index of reset pin index"
                range 0 127
                default 19

            config BOARD_USING_ILI9341_PIN_DC
            int "Specify the pin index of data&command switching"
                range 0 127
                default 18

        endif

    endmenu

    source "$BSP_DIR/../libraries/nu_packages/Kconfig"

endmenu