/** ****************************************************************************** * @file stm32g0xx_hal_rtc_ex.c * @author MCD Application Team * @brief Extended RTC HAL module driver. * This file provides firmware functions to manage the following * functionalities of the Real Time Clock (RTC) Extended peripheral: * + RTC Time Stamp functions * + RTC Tamper functions * + RTC Wake-up functions * + Extended Control functions * + Extended RTC features functions * @verbatim ============================================================================== ##### How to use this driver ##### ============================================================================== [..] (+) Enable the RTC domain access. (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour format using the HAL_RTC_Init() function. *** RTC Wakeup configuration *** ================================ [..] (+) To configure the RTC Wakeup Clock source and Counter use the HAL_RTCEx_SetWakeUpTimer() function. You can also configure the RTC Wakeup timer with interrupt mode using the HAL_RTCEx_SetWakeUpTimer_IT() function. (+) To read the RTC WakeUp Counter register, use the HAL_RTCEx_GetWakeUpTimer() function. *** Outputs configuration *** ============================= [..] The RTC has 2 different outputs: (+) RTC_ALARM: this output is used to manage the RTC Alarm A, Alarm B and WaKeUp signals. To output the selected RTC signal, use the HAL_RTC_Init() function. (+) RTC_CALIB: this output is 512Hz signal or 1Hz. To enable the RTC_CALIB, use the HAL_RTCEx_SetCalibrationOutPut() function. (+) Two pins can be used as RTC_ALARM or RTC_CALIB (PC13, PB2) managed on the RTC_OR register. (+) When the RTC_CALIB or RTC_ALARM output is selected, the RTC_OUT pin is automatically configured in output alternate function. *** Smooth digital Calibration configuration *** ================================================ [..] (+) Configure the RTC Original Digital Calibration Value and the corresponding calibration cycle period (32s,16s and 8s) using the HAL_RTCEx_SetSmoothCalib() function. *** TimeStamp configuration *** =============================== [..] (+) Enable the RTC TimeStamp using the HAL_RTCEx_SetTimeStamp() function. You can also configure the RTC TimeStamp with interrupt mode using the HAL_RTCEx_SetTimeStamp_IT() function. (+) To read the RTC TimeStamp Time and Date register, use the HAL_RTCEx_GetTimeStamp() function. *** Internal TimeStamp configuration *** =============================== [..] (+) Enable the RTC internal TimeStamp using the HAL_RTCEx_SetInternalTimeStamp() function. User has to check internal timestamp occurrence using __HAL_RTC_INTERNAL_TIMESTAMP_GET_FLAG. (+) To read the RTC TimeStamp Time and Date register, use the HAL_RTCEx_GetTimeStamp() function. *** Tamper configuration *** ============================ [..] (+) Enable the RTC Tamper and configure the Tamper filter count, trigger Edge or Level according to the Tamper filter (if equal to 0 Edge else Level) value, sampling frequency, NoErase, MaskFlag, precharge or discharge and Pull-UP using the HAL_RTCEx_SetTamper() function. You can configure RTC Tamper with interrupt mode using HAL_RTCEx_SetTamper_IT() function. (+) The default configuration of the Tamper erases the backup registers. To avoid erase, enable the NoErase field on the RTC_TAMPCR register. (+) With new RTC tamper configuration, you have to call HAL_RTC_Init() in order to perform TAMP base address offset calculation. (+) If you do not intend to have tamper using RTC clock, you can bypass its initialization by setting ClockEnable inti field to RTC_CLOCK_DISABLE. (+) Enable Internal tamper using HAL_RTCEx_SetInternalTamper. IT mode can be chosen using setting Interrupt field. *** Backup Data Registers configuration *** =========================================== [..] (+) To write to the RTC Backup Data registers, use the HAL_RTCEx_BKUPWrite() function. (+) To read the RTC Backup Data registers, use the HAL_RTCEx_BKUPRead() function. (+) Before calling those functions you have to call HAL_RTC_Init() in order to perform TAMP base address offset calculation. @endverbatim ****************************************************************************** * @attention * *

© Copyright (c) 2018 STMicroelectronics. * All rights reserved.

* * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the * License. You may obtain a copy of the License at: * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32g0xx_hal.h" /** @addtogroup STM32G0xx_HAL_Driver * @{ */ /** @addtogroup RTCEx * @brief RTC Extended HAL module driver * @{ */ #ifdef HAL_RTC_MODULE_ENABLED /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ /* Exported functions --------------------------------------------------------*/ /** @addtogroup RTCEx_Exported_Functions * @{ */ /** @addtogroup RTCEx_Exported_Functions_Group1 * @brief RTC TimeStamp and Tamper functions * @verbatim =============================================================================== ##### RTC TimeStamp and Tamper functions ##### =============================================================================== [..] This section provides functions allowing to configure TimeStamp feature @endverbatim * @{ */ /** * @brief Set TimeStamp. * @note This API must be called before enabling the TimeStamp feature. * @param hrtc RTC handle * @param TimeStampEdge Specifies the pin edge on which the TimeStamp is * activated. * This parameter can be one of the following values: * @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the * rising edge of the related pin. * @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the * falling edge of the related pin. * @param RTC_TimeStampPin specifies the RTC TimeStamp Pin. * This parameter can be one of the following values: * @arg RTC_TIMESTAMPPIN_DEFAULT: PC13 is selected as RTC TimeStamp Pin. * The RTC TimeStamp Pin is per default PC13, but for reasons of * compatibility, this parameter is required. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin) { uint32_t tmpreg; /* Check the parameters */ assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge)); assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Get the RTC_CR register and clear the bits to be configured */ tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); tmpreg|= TimeStampEdge; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Configure the Time Stamp TSEDGE and Enable bits */ hrtc->Instance->CR = (uint32_t)tmpreg; __HAL_RTC_TIMESTAMP_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Set TimeStamp with Interrupt. * @note This API must be called before enabling the TimeStamp feature. * @param hrtc RTC handle * @param TimeStampEdge Specifies the pin edge on which the TimeStamp is * activated. * This parameter can be one of the following values: * @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the * rising edge of the related pin. * @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the * falling edge of the related pin. * @param RTC_TimeStampPin Specifies the RTC TimeStamp Pin. * This parameter can be one of the following values: * @arg RTC_TIMESTAMPPIN_DEFAULT: PC13 is selected as RTC TimeStamp Pin. * The RTC TimeStamp Pin is per default PC13, but for reasons of * compatibility, this parameter is required. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp_IT(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin) { uint32_t tmpreg; /* Check the parameters */ assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge)); assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Get the RTC_CR register and clear the bits to be configured */ tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); tmpreg |= TimeStampEdge; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Configure the Time Stamp TSEDGE and Enable bits */ hrtc->Instance->CR = (uint32_t)tmpreg; __HAL_RTC_TIMESTAMP_ENABLE(hrtc); /* Enable IT timestamp */ __HAL_RTC_TIMESTAMP_ENABLE_IT(hrtc,RTC_IT_TS); /* RTC timestamp Interrupt Configuration: EXTI configuration */ __HAL_RTC_TIMESTAMP_EXTI_ENABLE_IT(); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactivate TimeStamp. * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateTimeStamp(RTC_HandleTypeDef *hrtc) { uint32_t tmpreg; /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* In case of interrupt mode is used, the interrupt source must disabled */ __HAL_RTC_TIMESTAMP_DISABLE_IT(hrtc, RTC_IT_TS); /* Get the RTC_CR register and clear the bits to be configured */ tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); /* Configure the Time Stamp TSEDGE and Enable bits */ hrtc->Instance->CR = (uint32_t)tmpreg; /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Set Internal TimeStamp. * @note This API must be called before enabling the internal TimeStamp feature. * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetInternalTimeStamp(RTC_HandleTypeDef *hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Configure the internal Time Stamp Enable bits */ __HAL_RTC_INTERNAL_TIMESTAMP_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactivate Internal TimeStamp. * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTimeStamp(RTC_HandleTypeDef *hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Configure the internal Time Stamp Enable bits */ __HAL_RTC_INTERNAL_TIMESTAMP_DISABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Get the RTC TimeStamp value. * @param hrtc RTC handle * @param sTimeStamp Pointer to Time structure * @param sTimeStampDate Pointer to Date structure * @param Format specifies the format of the entered parameters. * This parameter can be one of the following values: * @arg RTC_FORMAT_BIN: Binary data format * @arg RTC_FORMAT_BCD: BCD data format * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_GetTimeStamp(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef* sTimeStamp, RTC_DateTypeDef* sTimeStampDate, uint32_t Format) { uint32_t tmptime, tmpdate; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); /* Get the TimeStamp time and date registers values */ tmptime = (uint32_t)(hrtc->Instance->TSTR & RTC_TR_RESERVED_MASK); tmpdate = (uint32_t)(hrtc->Instance->TSDR & RTC_DR_RESERVED_MASK); /* Fill the Time structure fields with the read parameters */ sTimeStamp->Hours = (uint8_t)((tmptime & (RTC_TR_HT | RTC_TR_HU)) >> RTC_TSTR_HU_Pos); sTimeStamp->Minutes = (uint8_t)((tmptime & (RTC_TR_MNT | RTC_TR_MNU)) >>RTC_TSTR_MNU_Pos); sTimeStamp->Seconds = (uint8_t)((tmptime & (RTC_TR_ST | RTC_TR_SU)) >> RTC_TSTR_SU_Pos); sTimeStamp->TimeFormat = (uint8_t)((tmptime & (RTC_TR_PM)) >> RTC_TSTR_PM_Pos); sTimeStamp->SubSeconds = (uint32_t) hrtc->Instance->TSSSR; /* Fill the Date structure fields with the read parameters */ sTimeStampDate->Year = 0U; sTimeStampDate->Month = (uint8_t)((tmpdate & (RTC_DR_MT | RTC_DR_MU)) >> RTC_TSDR_MU_Pos); sTimeStampDate->Date = (uint8_t)(tmpdate & (RTC_DR_DT | RTC_DR_DU)); sTimeStampDate->WeekDay = (uint8_t)((tmpdate & (RTC_DR_WDU)) >> RTC_TSDR_WDU_Pos); /* Check the input parameters format */ if(Format == RTC_FORMAT_BIN) { /* Convert the TimeStamp structure parameters to Binary format */ sTimeStamp->Hours = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Hours); sTimeStamp->Minutes = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Minutes); sTimeStamp->Seconds = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Seconds); /* Convert the DateTimeStamp structure parameters to Binary format */ sTimeStampDate->Month = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Month); sTimeStampDate->Date = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Date); sTimeStampDate->WeekDay = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->WeekDay); } /* Clear the TIMESTAMP Flags */ __HAL_RTC_INTERNAL_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_ITSF); __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSF); return HAL_OK; } /** * @brief TimeStamp callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_TimeStampEventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_TimeStampEventCallback could be implemented in the user file */ } /** * @brief Handle TimeStamp interrupt request. * @param hrtc RTC handle * @retval None */ void HAL_RTCEx_TimeStampIRQHandler(RTC_HandleTypeDef *hrtc) { /* Get the TimeStamp interrupt source enable status */ if (READ_BIT(RTC->MISR, RTC_MISR_TSMF) != 0U) { #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call TimeStampEvent registered Callback */ hrtc->TimeStampEventCallback(hrtc); #else /* TIMESTAMP callback */ HAL_RTCEx_TimeStampEventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ /* Clearing flags after the Callback because the content of RTC_TSTR and RTC_TSDR are cleared when TSF bit is reset.*/ WRITE_REG(RTC->SCR, RTC_SCR_CITSF | RTC_SCR_CTSF); } /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; } /** * @brief Handle TimeStamp polling request. * @param hrtc RTC handle * @param Timeout Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForTimeStampEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); while(__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSF) == 0U) { if(__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSOVF) != 0U) { /* Clear the TIMESTAMP OverRun Flag */ __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSOVF); /* Change TIMESTAMP state */ hrtc->State = HAL_RTC_STATE_ERROR; return HAL_ERROR; } if(Timeout != HAL_MAX_DELAY) { if(((HAL_GetTick() - tickstart ) > Timeout)||(Timeout == 0U)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } /** * @} */ /** @addtogroup RTCEx_Exported_Functions_Group2 * @brief RTC Wake-up functions * @verbatim =============================================================================== ##### RTC Wake-up functions ##### =============================================================================== [..] This section provides functions allowing to configure Wake-up feature @endverbatim * @{ */ /** * @brief Set wake up timer. * @param hrtc RTC handle * @param WakeUpCounter Wake up counter * @param WakeUpClock Wake up clock * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock) { uint32_t tickstart; /* Check the parameters */ assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock)); assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Clear WUTE in RTC_CR to disable the wakeup timer */ CLEAR_BIT(RTC->CR, RTC_CR_WUTE); /* Poll WUTWF until it is set in RTC_ICSR to make sure the access to wakeup autoreload counter and to WUCKSEL[2:0] bits is allowed. This step must be skipped in calendar initialization mode. */ if (READ_BIT(RTC->ICSR, RTC_ICSR_INITF) == 0U) { tickstart = HAL_GetTick(); while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } } /* Clear the Wakeup Timer clock source bits in CR register */ hrtc->Instance->CR &= (uint32_t)~RTC_CR_WUCKSEL; /* Configure the clock source */ hrtc->Instance->CR |= (uint32_t)WakeUpClock; /* Configure the Wakeup Timer counter */ hrtc->Instance->WUTR = (uint32_t)WakeUpCounter; /* Enable the Wakeup Timer */ __HAL_RTC_WAKEUPTIMER_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Set wake up timer with interrupt. * @param hrtc RTC handle * @param WakeUpCounter Wake up counter * @param WakeUpClock Wake up clock * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer_IT(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock) { uint32_t tickstart; /* Check the parameters */ assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock)); assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Disable the Wake-Up timer */ __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc); /* Clear flag Wake-Up */ __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF); /* Poll WUTWF until it is set in RTC_ICSR to make sure the access to wakeup autoreload counter and to WUCKSEL[2:0] bits is allowed. This step must be skipped in calendar initialization mode. */ if (READ_BIT(RTC->ICSR, RTC_ICSR_INITF) == 0U) { tickstart = HAL_GetTick(); while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } } /* Configure the Wakeup Timer counter */ hrtc->Instance->WUTR = (uint32_t)WakeUpCounter; /* Clear the Wakeup Timer clock source bits in CR register */ hrtc->Instance->CR &= (uint32_t)~RTC_CR_WUCKSEL; /* Configure the clock source */ hrtc->Instance->CR |= (uint32_t)WakeUpClock; /* RTC WakeUpTimer Interrupt Configuration: EXTI configuration */ __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT(); /* Configure the Interrupt in the RTC_CR register */ __HAL_RTC_WAKEUPTIMER_ENABLE_IT(hrtc,RTC_IT_WUT); /* Enable the Wakeup Timer */ __HAL_RTC_WAKEUPTIMER_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactivate wake up timer counter. * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateWakeUpTimer(RTC_HandleTypeDef *hrtc) { uint32_t tickstart; /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Disable the Wakeup Timer */ __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc); /* In case of interrupt mode is used, the interrupt source must disabled */ __HAL_RTC_WAKEUPTIMER_DISABLE_IT(hrtc,RTC_IT_WUT); tickstart = HAL_GetTick(); /* Wait till RTC WUTWF flag is set and if Time out is reached exit */ while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Get wake up timer counter. * @param hrtc RTC handle * @retval Counter value */ uint32_t HAL_RTCEx_GetWakeUpTimer(RTC_HandleTypeDef *hrtc) { /* Get the counter value */ return ((uint32_t)(hrtc->Instance->WUTR & RTC_WUTR_WUT)); } /** * @brief Handle Wake Up Timer interrupt request. * @param hrtc RTC handle * @retval None */ void HAL_RTCEx_WakeUpTimerIRQHandler(RTC_HandleTypeDef *hrtc) { /* Get the pending status of the WAKEUPTIMER Interrupt */ if(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) != 0U) { /* Clear the WAKEUPTIMER interrupt pending bit */ __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF); #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call WakeUpTimerEvent registered Callback */ hrtc->WakeUpTimerEventCallback(hrtc); #else /* WAKEUPTIMER callback */ HAL_RTCEx_WakeUpTimerEventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ } /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; } /** * @brief Wake Up Timer callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_WakeUpTimerEventCallback could be implemented in the user file */ } /** * @brief Handle Wake Up Timer Polling. * @param hrtc RTC handle * @param Timeout Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForWakeUpTimerEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) == 0U) { if(Timeout != HAL_MAX_DELAY) { if(((HAL_GetTick() - tickstart ) > Timeout)||(Timeout == 0U)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Clear the WAKEUPTIMER Flag */ __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } /** * @} */ /** @addtogroup RTCEx_Exported_Functions_Group3 * @brief Extended Peripheral Control functions * @verbatim =============================================================================== ##### Extended Peripheral Control functions ##### =============================================================================== [..] This subsection provides functions allowing to (+) Write a data in a specified RTC Backup data register (+) Read a data in a specified RTC Backup data register (+) Set the Coarse calibration parameters. (+) Deactivate the Coarse calibration parameters (+) Set the Smooth calibration parameters. (+) Configure the Synchronization Shift Control Settings. (+) Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). (+) Deactivate the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). (+) Enable the RTC reference clock detection. (+) Disable the RTC reference clock detection. (+) Enable the Bypass Shadow feature. (+) Disable the Bypass Shadow feature. @endverbatim * @{ */ /** * @brief Set the Smooth calibration parameters. * @note To deactivate the smooth calibration, the field SmoothCalibPlusPulses * must be equal to SMOOTHCALIB_PLUSPULSES_RESET and the field * SmoothCalibMinusPulsesValue must be equal to 0. * @param hrtc RTC handle * @param SmoothCalibPeriod Select the Smooth Calibration Period. * This parameter can be can be one of the following values : * @arg RTC_SMOOTHCALIB_PERIOD_32SEC: The smooth calibration period is 32s. * @arg RTC_SMOOTHCALIB_PERIOD_16SEC: The smooth calibration period is 16s. * @arg RTC_SMOOTHCALIB_PERIOD_8SEC: The smooth calibration period is 8s. * @param SmoothCalibPlusPulses Select to Set or reset the CALP bit. * This parameter can be one of the following values: * @arg RTC_SMOOTHCALIB_PLUSPULSES_SET: Add one RTCCLK pulse every 2*11 pulses. * @arg RTC_SMOOTHCALIB_PLUSPULSES_RESET: No RTCCLK pulses are added. * @param SmoothCalibMinusPulsesValue Select the value of CALM[8:0] bits. * This parameter can be one any value from 0 to 0x000001FF. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetSmoothCalib(RTC_HandleTypeDef* hrtc, uint32_t SmoothCalibPeriod, uint32_t SmoothCalibPlusPulses, uint32_t SmoothCalibMinusPulsesValue) { uint32_t tickstart; /* Check the parameters */ assert_param(IS_RTC_SMOOTH_CALIB_PERIOD(SmoothCalibPeriod)); assert_param(IS_RTC_SMOOTH_CALIB_PLUS(SmoothCalibPlusPulses)); assert_param(IS_RTC_SMOOTH_CALIB_MINUS(SmoothCalibMinusPulsesValue)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* check if a calibration is pending*/ if((hrtc->Instance->ICSR & RTC_ICSR_RECALPF) != 0U) { tickstart = HAL_GetTick(); /* check if a calibration is pending*/ while((hrtc->Instance->ICSR & RTC_ICSR_RECALPF) != 0U) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } } /* Configure the Smooth calibration settings */ hrtc->Instance->CALR = (uint32_t)((uint32_t)SmoothCalibPeriod | (uint32_t)SmoothCalibPlusPulses | (uint32_t)SmoothCalibMinusPulsesValue); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Configure the Synchronization Shift Control Settings. * @note When REFCKON is set, firmware must not write to Shift control register. * @param hrtc RTC handle * @param ShiftAdd1S Select to add or not 1 second to the time calendar. * This parameter can be one of the following values: * @arg RTC_SHIFTADD1S_SET: Add one second to the clock calendar. * @arg RTC_SHIFTADD1S_RESET: No effect. * @param ShiftSubFS Select the number of Second Fractions to substitute. * This parameter can be one any value from 0 to 0x7FFF. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetSynchroShift(RTC_HandleTypeDef* hrtc, uint32_t ShiftAdd1S, uint32_t ShiftSubFS) { uint32_t tickstart; /* Check the parameters */ assert_param(IS_RTC_SHIFT_ADD1S(ShiftAdd1S)); assert_param(IS_RTC_SHIFT_SUBFS(ShiftSubFS)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); tickstart = HAL_GetTick(); /* Wait until the shift is completed*/ while((hrtc->Instance->ICSR & RTC_ICSR_SHPF) != 0U) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } /* Check if the reference clock detection is disabled */ if((hrtc->Instance->CR & RTC_CR_REFCKON) == 0U) { /* Configure the Shift settings */ hrtc->Instance->SHIFTR = (uint32_t)(uint32_t)(ShiftSubFS) | (uint32_t)(ShiftAdd1S); /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == 0U) { if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } } } else { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). * @param hrtc RTC handle * @param CalibOutput Select the Calibration output Selection . * This parameter can be one of the following values: * @arg RTC_CALIBOUTPUT_512HZ: A signal has a regular waveform at 512Hz. * @arg RTC_CALIBOUTPUT_1HZ: A signal has a regular waveform at 1Hz. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetCalibrationOutPut(RTC_HandleTypeDef* hrtc, uint32_t CalibOutput) { /* Check the parameters */ assert_param(IS_RTC_CALIB_OUTPUT(CalibOutput)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Clear flags before config */ hrtc->Instance->CR &= (uint32_t)~RTC_CR_COSEL; /* Configure the RTC_CR register */ hrtc->Instance->CR |= (uint32_t)CalibOutput; __HAL_RTC_CALIBRATION_OUTPUT_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactivate the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateCalibrationOutPut(RTC_HandleTypeDef* hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); __HAL_RTC_CALIBRATION_OUTPUT_DISABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Enable the RTC reference clock detection. * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetRefClock(RTC_HandleTypeDef* hrtc) { HAL_StatusTypeDef status; /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Enter Initialization mode */ status = RTC_EnterInitMode(hrtc); if(status == HAL_OK) { /* Enable clockref detection */ __HAL_RTC_CLOCKREF_DETECTION_ENABLE(hrtc); /* Exit Initialization mode */ status = RTC_ExitInitMode(hrtc); } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); if (status == HAL_OK) { hrtc->State = HAL_RTC_STATE_READY; } /* Process Unlocked */ __HAL_UNLOCK(hrtc); return status; } /** * @brief Disable the RTC reference clock detection. * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateRefClock(RTC_HandleTypeDef* hrtc) { HAL_StatusTypeDef status; /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Enter Initialization mode */ status = RTC_EnterInitMode(hrtc); if (status == HAL_OK) { /* Disable clockref detection */ __HAL_RTC_CLOCKREF_DETECTION_DISABLE(hrtc); /* Exit Initialization mode */ status = RTC_ExitInitMode(hrtc); } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); if (status == HAL_OK) { hrtc->State = HAL_RTC_STATE_READY; } /* Process Unlocked */ __HAL_UNLOCK(hrtc); return status; } /** * @brief Enable the Bypass Shadow feature. * @note When the Bypass Shadow is enabled the calendar value are taken * directly from the Calendar counter. * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_EnableBypassShadow(RTC_HandleTypeDef* hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Set the BYPSHAD bit */ hrtc->Instance->CR |= (uint8_t)RTC_CR_BYPSHAD; /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Disable the Bypass Shadow feature. * @note When the Bypass Shadow is enabled the calendar value are taken * directly from the Calendar counter. * @param hrtc RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DisableBypassShadow(RTC_HandleTypeDef* hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Reset the BYPSHAD bit */ hrtc->Instance->CR &= ((uint8_t)~RTC_CR_BYPSHAD); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @} */ /** @addtogroup RTCEx_Exported_Functions_Group4 * @brief Extended features functions * @verbatim =============================================================================== ##### Extended features functions ##### =============================================================================== [..] This section provides functions allowing to: (+) RTC Alarm B callback (+) RTC Poll for Alarm B request @endverbatim * @{ */ /** * @brief Alarm B callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_AlarmBEventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_AlarmBEventCallback could be implemented in the user file */ } /** * @brief Handle Alarm B Polling request. * @param hrtc RTC handle * @param Timeout Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForAlarmBEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBF) == 0U) { if(Timeout != HAL_MAX_DELAY) { if(((HAL_GetTick() - tickstart ) > Timeout)||(Timeout == 0U)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Clear the Alarm Flag */ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } /** * @} */ /** @addtogroup RTCEx_Exported_Functions_Group5 * @brief Extended RTC Tamper functions * @verbatim ============================================================================== ##### Tamper functions ##### ============================================================================== [..] (+) Before calling any tamper or internal tamper function, you have to call first HAL_RTC_Init() function. (+) In that ine you can select to output tamper event on RTC pin. [..] (+) Enable the Tamper and configure the Tamper filter count, trigger Edge or Level according to the Tamper filter (if equal to 0 Edge else Level) value, sampling frequency, NoErase, MaskFlag, precharge or discharge and Pull-UP, timestamp using the HAL_RTCEx_SetTamper() function. You can configure Tamper with interrupt mode using HAL_RTCEx_SetTamper_IT() function. (+) The default configuration of the Tamper erases the backup registers. To avoid erase, enable the NoErase field on the TAMP_TAMPCR register. [..] (+) Enable Internal Tamper and configure it with interrupt, timestamp using the HAL_RTCEx_SetInternalTamper() function. @endverbatim * @{ */ /** * @brief Set Tamper * @param hrtc RTC handle * @param sTamper Pointer to Tamper Structure. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef* sTamper) { uint32_t tmpreg; /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); /* Check the parameters */ assert_param(IS_RTC_TAMPER(sTamper->Tamper)); assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger)); assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase)); assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag)); assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter)); assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency)); assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration)); assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp)); assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection)); /* Configuration register 2 */ tmpreg = tamp->CR2; tmpreg &= ~((sTamper->Tamper << 24) | (sTamper->Tamper << 16) | (sTamper->Tamper)); if(sTamper->Trigger != RTC_TAMPERTRIGGER_RISINGEDGE) { tmpreg |= (sTamper->Tamper << 24); } if(sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) { tmpreg |= (sTamper->Tamper << 16); } if(sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) { tmpreg |= sTamper->Tamper; } tamp->CR2 = tmpreg; /* Filter control register */ tamp->FLTCR = (sTamper->Filter) | (sTamper->SamplingFrequency) | \ (sTamper->PrechargeDuration) | (sTamper->TamperPullUp); /* timestamp on tamper */ if((hrtc->Instance->CR & RTC_CR_TAMPTS) != (sTamper->TimeStampOnTamperDetection)) { __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); tmpreg = (hrtc->Instance->CR & ~RTC_CR_TAMPTS); hrtc->Instance->CR = (tmpreg | (sTamper->TimeStampOnTamperDetection)); __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); } /* Control register 1 */ tamp->CR1 |= (sTamper->Tamper); return HAL_OK; } /** * @brief Set Tamper in IT mode * @param hrtc RTC handle * @param sTamper Pointer to Tamper Structure. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef* sTamper) { uint32_t tmpreg; /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); /* Check the parameters */ assert_param(IS_RTC_TAMPER(sTamper->Tamper)); assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger)); assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase)); assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag)); assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter)); assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency)); assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration)); assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp)); assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection)); /* Configuration register 2 */ tmpreg = tamp->CR2; tmpreg &= ~((sTamper->Tamper << 24) | (sTamper->Tamper << 16) | (sTamper->Tamper)); if(sTamper->Trigger != RTC_TAMPERTRIGGER_RISINGEDGE) { tmpreg |= (sTamper->Tamper << 24); } if(sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) { tmpreg |= (sTamper->Tamper << 16); } if(sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) { tmpreg |= sTamper->Tamper; } tamp->CR2 = tmpreg; /* Filter control register */ tamp->FLTCR = (sTamper->Filter) | (sTamper->SamplingFrequency) | \ (sTamper->PrechargeDuration) | (sTamper->TamperPullUp); /* timestamp on tamper */ if((hrtc->Instance->CR & RTC_CR_TAMPTS) != (sTamper->TimeStampOnTamperDetection)) { __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); tmpreg = (hrtc->Instance->CR & ~RTC_CR_TAMPTS); hrtc->Instance->CR = (tmpreg | (sTamper->TimeStampOnTamperDetection)); __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); } /* RTC Tamper Interrupt Configuration: EXTI configuration */ __HAL_RTC_TAMPER_EXTI_ENABLE_IT(); /* Interrupt enable register */ tamp->IER |= sTamper->Tamper; /* Control register 1 */ tamp->CR1 |= (sTamper->Tamper); return HAL_OK; } /** * @brief Deactivate Tamper. * @param hrtc RTC handle * @param Tamper Selected tamper pin. * This parameter can be a combination of the following values: * @arg RTC_TAMPER_1 * @arg RTC_TAMPER_2 * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef *hrtc, uint32_t Tamper) { /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); assert_param(IS_RTC_TAMPER(Tamper)); /* Disable the selected Tamper pin */ tamp->CR1 &= ~Tamper; /* Clear tamper mask/noerase/trigger configuration */ tamp->CR2 &= ~((Tamper << 24) | (Tamper << 16) | Tamper); /* Clear tamper interrupt mode configuration */ tamp->IER &= ~Tamper; return HAL_OK; } /** * @brief Tamper event polling. * @param hrtc RTC handle * @param Tamper Selected tamper pin. * This parameter can be a combination of the following values: * @arg RTC_TAMPER_1 * @arg RTC_TAMPER_2 * @arg RTC_TAMPER_3 (*) * @param Timeout Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForTamperEvent(RTC_HandleTypeDef *hrtc, uint32_t Tamper, uint32_t Timeout) { /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); assert_param(IS_RTC_TAMPER(Tamper)); uint32_t tickstart = HAL_GetTick(); /* Get the status of the Interrupt */ while((tamp->SR & Tamper) != Tamper) { if(Timeout != HAL_MAX_DELAY) { if(((HAL_GetTick() - tickstart ) > Timeout)||(Timeout == 0U)) { return HAL_TIMEOUT; } } } /* Clear the Tamper Flag */ tamp->SCR = Tamper; return HAL_OK; } /** * @brief Set Internal Tamper in interrupt mode * @param hrtc RTC handle * @param sIntTamper Pointer to Internal Tamper Structure. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef* sIntTamper) { /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); uint32_t tmpreg; /* Check the parameters */ assert_param(IS_RTC_INTERNAL_TAMPER(sIntTamper->IntTamper)); assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sIntTamper->TimeStampOnTamperDetection)); /* timestamp on internal tamper */ if((hrtc->Instance->CR & RTC_CR_TAMPTS) != (sIntTamper->TimeStampOnTamperDetection)) { __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); tmpreg = (hrtc->Instance->CR & ~RTC_CR_TAMPTS); hrtc->Instance->CR = (tmpreg | (sIntTamper->TimeStampOnTamperDetection)); __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); } /* Control register 1 */ tamp->CR1 |= (sIntTamper->IntTamper); return HAL_OK; } /** * @brief Set Internal Tamper * @param hrtc RTC handle * @param sIntTamper Pointer to Internal Tamper Structure. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper_IT(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef* sIntTamper) { /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); uint32_t tmpreg; /* Check the parameters */ assert_param(IS_RTC_INTERNAL_TAMPER(sIntTamper->IntTamper)); assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sIntTamper->TimeStampOnTamperDetection)); /* timestamp on internal tamper */ if((hrtc->Instance->CR & RTC_CR_TAMPTS) != (sIntTamper->TimeStampOnTamperDetection)) { __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); tmpreg = (hrtc->Instance->CR & ~RTC_CR_TAMPTS); hrtc->Instance->CR = (tmpreg | (sIntTamper->TimeStampOnTamperDetection)); __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); } /* RTC Tamper Interrupt Configuration: EXTI configuration */ __HAL_RTC_TAMPER_EXTI_ENABLE_IT(); /* Interrupt enable register */ tamp->IER |= sIntTamper->IntTamper; /* Control register 1 */ tamp->CR1 |= (sIntTamper->IntTamper); return HAL_OK; } /** * @brief Deactivate Internal Tamper. * @param hrtc RTC handle * @param IntTamper Selected internal tamper event. * This parameter can be any combination of existing internal tampers. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTamper(RTC_HandleTypeDef *hrtc, uint32_t IntTamper) { /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); assert_param(IS_RTC_INTERNAL_TAMPER(IntTamper)); /* Disable the selected Tamper pin */ tamp->CR1 &= ~IntTamper; /* Clear internal tamper interrupt mode configuration */ tamp->IER &= ~IntTamper; return HAL_OK; } /** * @brief Internal Tamper event polling. * @param hrtc RTC handle * @param IntTamper selected tamper. * This parameter can be any combination of existing internal tampers. * @param Timeout Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForInternalTamperEvent(RTC_HandleTypeDef *hrtc, uint32_t IntTamper, uint32_t Timeout) { /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); assert_param(IS_RTC_INTERNAL_TAMPER(IntTamper)); uint32_t tickstart = HAL_GetTick(); /* Get the status of the Interrupt */ while((tamp->SR & IntTamper) != IntTamper) { if(Timeout != HAL_MAX_DELAY) { if(((HAL_GetTick() - tickstart ) > Timeout)||(Timeout == 0U)) { return HAL_TIMEOUT; } } } /* Clear the Tamper Flag */ tamp->SCR = IntTamper; return HAL_OK; } /** * @brief Handle Tamper interrupt request. * @param hrtc RTC handle * @retval None */ void HAL_RTCEx_TamperIRQHandler(RTC_HandleTypeDef *hrtc) { uint32_t tmp; /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); /* Get interrupt status */ tmp = tamp->MISR; /* Immediately clear flags */ tamp->SCR = tmp; /* Check Tamper1 status */ if((tmp & RTC_TAMPER_1) == RTC_TAMPER_1) { #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call Tamper 1 Event registered Callback */ hrtc->Tamper1EventCallback(hrtc); #else /* Tamper1 callback */ HAL_RTCEx_Tamper1EventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ } /* Check Tamper2 status */ if((tmp & RTC_TAMPER_2) == RTC_TAMPER_2) { #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call Tamper 2 Event registered Callback */ hrtc->Tamper2EventCallback(hrtc); #else /* Tamper2 callback */ HAL_RTCEx_Tamper2EventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ } #if defined(TAMP_CR1_TAMP3E) /* Check Tamper3 status */ if((tmp & RTC_TAMPER_3) == RTC_TAMPER_3) { #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call Tamper 3 Event registered Callback */ hrtc->Tamper3EventCallback(hrtc); #else /* Tamper3 callback */ HAL_RTCEx_Tamper3EventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ } #endif /* Check Internal Tamper3 status */ if((tmp & RTC_INT_TAMPER_3) == RTC_INT_TAMPER_3) { #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call Internal Tamper 3 Event registered Callback */ hrtc->InternalTamper3EventCallback(hrtc); #else /* Internal Tamper3 callback */ HAL_RTCEx_InternalTamper3EventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ } /* Check Internal Tamper4 status */ if((tmp & RTC_INT_TAMPER_4) == RTC_INT_TAMPER_4) { #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call Internal Tamper 4 Event registered Callback */ hrtc->InternalTamper4EventCallback(hrtc); #else /* Internal Tamper4 callback */ HAL_RTCEx_InternalTamper4EventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ } /* Check Internal Tamper5 status */ if((tmp & RTC_INT_TAMPER_5) == RTC_INT_TAMPER_5) { #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call Internal Tamper 5 Event registered Callback */ hrtc->InternalTamper5EventCallback(hrtc); #else /* Internal Tamper5 callback */ HAL_RTCEx_InternalTamper5EventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ } /* Check Internal Tamper6 status */ if((tmp & RTC_INT_TAMPER_6) == RTC_INT_TAMPER_6) { #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) /* Call Internal Tamper 6 Event registered Callback */ hrtc->InternalTamper6EventCallback(hrtc); #else /* Internal Tamper6 callback */ HAL_RTCEx_InternalTamper6EventCallback(hrtc); #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ } } /** * @brief Tamper 1 callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_Tamper1EventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_Tamper1EventCallback could be implemented in the user file */ } /** * @brief Tamper 2 callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_Tamper2EventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_Tamper2EventCallback could be implemented in the user file */ } #if defined(TAMP_CR1_TAMP3E) /** * @brief Tamper 3 callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_Tamper3EventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_Tamper2EventCallback could be implemented in the user file */ } #endif /** * @brief Internal Tamper 3 callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_InternalTamper3EventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_InternalTamper3EventCallback could be implemented in the user file */ } /** * @brief Internal Tamper 4 callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_InternalTamper4EventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_InternalTamper4EventCallback could be implemented in the user file */ } /** * @brief Internal Tamper 5 callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_InternalTamper5EventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_InternalTamper5EventCallback could be implemented in the user file */ } /** * @brief Internal Tamper 6 callback. * @param hrtc RTC handle * @retval None */ __weak void HAL_RTCEx_InternalTamper6EventCallback(RTC_HandleTypeDef *hrtc) { /* Prevent unused argument(s) compilation warning */ UNUSED(hrtc); /* NOTE : This function should not be modified, when the callback is needed, the HAL_RTCEx_InternalTamper6EventCallback could be implemented in the user file */ } /** * @} */ /** @addtogroup RTCEx_Exported_Functions_Group6 * @brief Extended RTC Backup register functions * @verbatim =============================================================================== ##### Extended RTC Backup register functions ##### =============================================================================== [..] (+) Before calling any tamper or internal tamper function, you have to call first HAL_RTC_Init() function. (+) In that ine you can select to output tamper event on RTC pin. [..] This subsection provides functions allowing to (+) Write a data in a specified RTC Backup data register (+) Read a data in a specified RTC Backup data register @endverbatim * @{ */ /** * @brief Write a data in a specified RTC Backup data register. * @param hrtc RTC handle * @param BackupRegister: RTC Backup data Register number. * This parameter can be: RTC_BKP_DRx where x can be from 0 to 4 * specify the register. * @param Data Data to be written in the specified Backup data register. * @retval None */ void HAL_RTCEx_BKUPWrite(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister, uint32_t Data) { uint32_t tmp; /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); /* Check the parameters */ assert_param(IS_RTC_BKP(BackupRegister)); tmp = (uint32_t)&(tamp->BKP0R); tmp += (BackupRegister * 4U); /* Write the specified register */ *(__IO uint32_t *)tmp = (uint32_t)Data; } /** * @brief Reads data from the specified RTC Backup data Register. * @param hrtc RTC handle * @param BackupRegister RTC Backup data Register number. * This parameter can be: RTC_BKP_DRx where x can be from 0 to 4 * specify the register. * @retval Read value */ uint32_t HAL_RTCEx_BKUPRead(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister) { uint32_t tmp ; /* Process TAMP instance pointer */ TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + hrtc->TampOffset); /* Check the parameters */ assert_param(IS_RTC_BKP(BackupRegister)); tmp = (uint32_t)&(tamp->BKP0R); tmp += (BackupRegister * 4U); /* Read the specified register */ return (*(__IO uint32_t *)tmp); } /** * @} */ /** * @} */ #endif /* HAL_RTC_MODULE_ENABLED */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/