Remove calls to set_timer outside arch/

There is no need to use set_timer(). Replace with appropriate use of
get_timer()
Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>
Acked-by: NWolfgang Denk <wd@denx.de>

board/BuS/EB+MCF-EV123/flash.c

@@ -157,6 +157,7 @@ int amd_flash_erase_sector(flash_info_t * info, int sector)
 {
 	int state;
 	ulong result;
+	ulong start;
 
 	volatile u16 *addr =
 				(volatile u16 *) (info->start[sector]);
@@ -171,13 +172,13 @@ int amd_flash_erase_sector(flash_info_t * info, int sector)
 
 	/* wait until flash is ready */
 	state = 0;
-	set_timer (0);
+	start = get_timer(0);
 
 	do {
 		result = *addr;
 
 		/* check timeout */
-		if (get_timer (0) > CONFIG_SYS_FLASH_ERASE_TOUT) {
+		if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) {
 			MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
 			state = ERR_TIMOUT;
 		}
@@ -267,6 +268,7 @@ volatile static int amd_write_word (flash_info_t * info, ulong dest, u16 data)
 	ulong result;
 	int cflag, iflag;
 	int state;
+	ulong start;
 
 	/*
 	 * Check if Flash is (sufficiently) erased
@@ -295,7 +297,7 @@ volatile static int amd_write_word (flash_info_t * info, ulong dest, u16 data)
 	*addr = data;
 
 	/* arm simple, non interrupt dependent timer */
-	set_timer (0);
+	start = get_timer(0);
 
 	/* wait until flash is ready */
 	state = 0;
@@ -303,7 +305,7 @@ volatile static int amd_write_word (flash_info_t * info, ulong dest, u16 data)
 		result = *addr;
 
 		/* check timeout */
-		if (get_timer (0) > CONFIG_SYS_FLASH_ERASE_TOUT) {
+		if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) {
 				state = ERR_TIMOUT;
 		}
 		if (!state && ((result & BIT_RDY_MASK) == (data & BIT_RDY_MASK)))

board/cobra5272/flash.c

@@ -147,6 +147,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 	int iflag, cflag, prot, sect;
 	int rc = ERR_OK;
 	int chip1;
+	ulong start;
 
 	/* first look for protection bits */
 
@@ -190,7 +191,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 		printf ("Erasing sector %2d ... ", sect);
 
 		/* arm simple, non interrupt dependent timer */
-		set_timer (0);
+		start = get_timer(0);
 
 		if (info->protect[sect] == 0) {	/* not protected */
 			volatile u16 *addr =
@@ -211,7 +212,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 				result = *addr;
 
 				/* check timeout */
-				if (get_timer (0) > CONFIG_SYS_FLASH_ERASE_TOUT) {
+				if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) {
 					MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
 					chip1 = TMO;
 					break;
@@ -264,6 +265,7 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 	int rc = ERR_OK;
 	int cflag, iflag;
 	int chip1;
+	ulong start;
 
 	/*
 	 * Check if Flash is (sufficiently) erased
@@ -291,7 +293,7 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 	*addr = data;
 
 	/* arm simple, non interrupt dependent timer */
-	set_timer (0);
+	start = get_timer(0);
 
 	/* wait until flash is ready */
 	chip1 = 0;
@@ -299,7 +301,7 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 		result = *addr;
 
 		/* check timeout */
-		if (get_timer (0) > CONFIG_SYS_FLASH_ERASE_TOUT) {
+		if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) {
 			chip1 = ERR | TMO;
 			break;
 		}

board/idmr/flash.c

@@ -130,6 +130,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 	int iflag, prot, sect;
 	int rc = ERR_OK;
 	int chip1;
+	ulong start;
 
 	/* first look for protection bits */
 
@@ -170,7 +171,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 		printf ("Erasing sector %2d ... ", sect);
 
 		/* arm simple, non interrupt dependent timer */
-		set_timer (0);
+		start = get_timer(0);
 
 		if (info->protect[sect] == 0) {	/* not protected */
 			volatile u16 *addr =
@@ -191,7 +192,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 				result = *addr;
 
 				/* check timeout */
-				if (get_timer (0) > CONFIG_SYS_FLASH_ERASE_TOUT * CONFIG_SYS_HZ / 1000) {
+				if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT * CONFIG_SYS_HZ / 1000) {
 					MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
 					chip1 = TMO;
 					break;
@@ -248,6 +249,7 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 	int rc = ERR_OK;
 	int iflag;
 	int chip1;
+	ulong start;
 
 	/*
 	 * Check if Flash is (sufficiently) erased
@@ -272,7 +274,7 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 	*addr = data;
 
 	/* arm simple, non interrupt dependent timer */
-	set_timer (0);
+	start = get_timer(0);
 
 	/* wait until flash is ready */
 	chip1 = 0;
@@ -280,7 +282,7 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 		result = *addr;
 
 		/* check timeout */
-		if (get_timer (0) > CONFIG_SYS_FLASH_ERASE_TOUT * CONFIG_SYS_HZ / 1000) {
+		if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT * CONFIG_SYS_HZ / 1000) {
 			chip1 = ERR | TMO;
 			break;
 		}