board/ls1021aqds: Add DDR4 support

LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: NYork Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>

arch/arm/include/asm/arch-ls102xa/config.h

@@ -50,7 +50,11 @@
 #ifdef CONFIG_DDR_SPD
 #define CONFIG_SYS_FSL_DDR_BE
 #define CONFIG_VERY_BIG_RAM
+#ifdef CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_FSL_DDRC_GEN4
+#else
 #define CONFIG_SYS_FSL_DDRC_ARM_GEN3
+#endif
 #define CONFIG_SYS_FSL_DDR
 #define CONFIG_SYS_LS1_DDR_BLOCK1_SIZE		((phys_size_t)2 << 30)
 #define CONFIG_MAX_MEM_MAPPED			CONFIG_SYS_LS1_DDR_BLOCK1_SIZE
@@ -71,6 +75,7 @@
 #define CONFIG_MAX_CPUS				2
 #define CONFIG_SYS_FSL_IFC_BANK_COUNT		8
 #define CONFIG_NUM_DDR_CONTROLLERS		1
+#define CONFIG_SYS_FSL_DDR_VER			FSL_DDR_VER_5_0
 #else
 #error SoC not defined
 #endif

board/freescale/ls1021aqds/MAINTAINERS

@@ -4,3 +4,4 @@ S:	Maintained
 F:	board/freescale/ls1021aqds/
 F:	include/configs/ls1021aqds.h
 F:	configs/ls1021aqds_nor_defconfig
+F:	configs/ls1021aqds_ddr4_nor_defconfig

board/freescale/ls1021aqds/ddr.c

@@ -79,7 +79,6 @@ found:
 	 */
 	popts->wrlvl_override = 1;
 	popts->wrlvl_sample = 0xf;
-	popts->cswl_override = DDR_CSWL_CS0;
 
 	/*
 	 * Rtt and Rtt_WR override
@@ -89,9 +88,17 @@ found:
 	/* Enable ZQ calibration */
 	popts->zq_en = 1;
 
+#ifdef CONFIG_SYS_FSL_DDR4
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
+#else
+	popts->cswl_override = DDR_CSWL_CS0;
+
 	/* DHC_EN =1, ODT = 75 Ohm */
 	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
 	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
 }
 
 #ifdef CONFIG_SYS_DDR_RAW_TIMING

board/freescale/ls1021aqds/ddr.h

@@ -30,6 +30,13 @@ static const struct board_specific_parameters udimm0[] = {
 	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
 	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
 	 */
+#ifdef CONFIG_SYS_FSL_DDR4
+	{2,  1666, 0, 4,     7, 0x0808090B, 0x0C0D0E0A,},
+	{2,  1900, 0, 4,     6, 0x08080A0C, 0x0D0E0F0A,},
+	{1,  1666, 0, 4,     8, 0x090A0B0B, 0x0C0D0E0C,},
+	{1,  1900, 0, 4,     9, 0x0A0B0C0B, 0x0D0E0F0D,},
+	{1,  2200, 0, 4,    10, 0x0B0C0D0C, 0x0E0F110E,},
+#elif defined(CONFIG_SYS_FSL_DDR3)
 	{1,  833,  1, 6,     8, 0x06060607, 0x08080807,   0x1f,    2,  0},
 	{1,  1350, 1, 6,     8, 0x0708080A, 0x0A0B0C09,   0x1f,    2,  0},
 	{1,  833,  2, 6,     8, 0x06060607, 0x08080807,   0x1f,    2,  0},
@@ -39,6 +46,9 @@ static const struct board_specific_parameters udimm0[] = {
 	{2,  1350, 0, 6,     8, 0x0708080A, 0x0A0B0C09,   0x1f,    2,  0},
 	{2,  1666, 4, 4,   0xa, 0x0B08090C, 0x0B0E0D0A,   0x1f,    2,  0},
 	{2,  1666, 0, 4,   0xa, 0x0B08090C, 0x0B0E0D0A,   0x1f,    2,  0},
+#else
+#error DDR type not defined
+#endif
 	{}
 };
 

configs/ls1021aqds_ddr4_nor_defconfig

+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_ARM=y
+CONFIG_TARGET_LS1021AQDS=y

include/configs/ls1021aqds.h

@@ -49,10 +49,12 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_DDR_SPD
 #define SPD_EEPROM_ADDRESS		0x51
 #define CONFIG_SYS_SPD_BUS_NUM		0
-#define CONFIG_SYS_DDR_RAW_TIMING
 
 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
+#ifndef CONFIG_SYS_FSL_DDR4
 #define CONFIG_SYS_FSL_DDR3		/* Use DDR3 memory */
+#define CONFIG_SYS_DDR_RAW_TIMING
+#endif
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	4