diff --git a/board/sipeed/maix/Kconfig b/board/sipeed/maix/Kconfig index 4c42dd20878e40432fb4312ae078437c40c5e705..2cdea8ea813a833861edaf944f2147773f03ca8b 100644 --- a/board/sipeed/maix/Kconfig +++ b/board/sipeed/maix/Kconfig @@ -53,4 +53,20 @@ config BOARD_SPECIFIC_OPTIONS imply CMD_GPIO imply LED imply LED_GPIO + imply SPI + imply DESIGNWARE_SPI + imply SPI_FLASH_GIGADEVICE + imply SPI_FLASH_WINBOND + imply DM_MTD + imply SPI_FLASH_MTD + imply CMD_MTD + imply ENV_IS_IN_SPI_FLASH + imply MMC + imply MMC_BROKEN_CD + imply MMC_SPI + imply CMD_MMC + imply DOS_PARTITION + imply EFI_PARTITION + imply CMD_PART + imply CMD_FS_GENERIC endif diff --git a/configs/sipeed_maix_bitm_defconfig b/configs/sipeed_maix_bitm_defconfig index 459bf0d5301cc96dc7f6dd49f89008fd26a13eff..210848cccf2d7a1deb9a279fc0690858e31e897b 100644 --- a/configs/sipeed_maix_bitm_defconfig +++ b/configs/sipeed_maix_bitm_defconfig @@ -1,8 +1,19 @@ CONFIG_RISCV=y +CONFIG_ENV_SIZE=0x1000 +CONFIG_ENV_OFFSET=0xfff000 +CONFIG_ENV_SECT_SIZE=0x1000 CONFIG_TARGET_SIPEED_MAIX=y CONFIG_ARCH_RV64I=y CONFIG_STACK_SIZE=0x100000 +CONFIG_USE_BOOTCOMMAND=y +CONFIG_BOOTCOMMAND="run k210_bootcmd" +CONFIG_HUSH_PARSER=y +CONFIG_MTDIDS_DEFAULT="nor0=spi3:0" +CONFIG_MTDPARTS_DEFAULT="nor0:1M(u-boot),0x1000@0xfff000(env)" # CONFIG_NET is not set # CONFIG_INPUT is not set +CONFIG_SF_DEFAULT_BUS=3 # CONFIG_DM_ETH is not set +CONFIG_FS_EXT4=y +CONFIG_FS_FAT=y # CONFIG_EFI_LOADER is not set diff --git a/doc/board/sipeed/maix.rst b/doc/board/sipeed/maix.rst index 92f2d112a99783f724af5b8948456bb0c9c0c220..bf945b3458d412da1cb1e07bc99c32dbdd143b7e 100644 --- a/doc/board/sipeed/maix.rst +++ b/doc/board/sipeed/maix.rst @@ -70,6 +70,7 @@ console shall be opened immediately. Boot output should look like the following: U-Boot 2020.04-rc2-00087-g2221cc09c1-dirty (Feb 28 2020 - 13:53:09 -0500) DRAM: 8 MiB + MMC: spi@53000000:slot@0: 0 In: serial@38000000 Out: serial@38000000 Err: serial@38000000 @@ -118,14 +119,115 @@ The value of FW_PAYLOAD_OFFSET must match CONFIG_SYS_TEXT_BASE - 0x80000000. The file to flash is build/platform/kendryte/k210/firmware/fw_payload.bin. +Booting +^^^^^^^ + +The default boot process is to load and boot the files ``/uImage`` and +``/k210.dtb`` off of the first partition of the MMC. For Linux, this will result +in an output like + +.. code-block:: none + + U-Boot 2020.10-00691-gd1d651d988-dirty (Oct 16 2020 - 17:05:24 -0400) + + DRAM: 8 MiB + MMC: spi@53000000:slot@0: 0 + Loading Environment from SPIFlash... SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB + OK + In: serial@38000000 + Out: serial@38000000 + Err: serial@38000000 + Hit any key to stop autoboot: 0 + 1827380 bytes read in 1044 ms (1.7 MiB/s) + 13428 bytes read in 10 ms (1.3 MiB/s) + ## Booting kernel from Legacy Image at 80060000 ... + Image Name: linux + Image Type: RISC-V Linux Kernel Image (uncompressed) + Data Size: 1827316 Bytes = 1.7 MiB + Load Address: 80000000 + Entry Point: 80000000 + Verifying Checksum ... OK + ## Flattened Device Tree blob at 80400000 + Booting using the fdt blob at 0x80400000 + Loading Kernel Image + Loading Device Tree to 00000000803f9000, end 00000000803ff473 ... OK + + Starting kernel ... + + [ 0.000000] Linux version 5.9.0-00021-g6dcc2f0814c6-dirty (sean@godwin) (riscv64-linux-gnu-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35) #34 SMP Fri Oct 16 14:40:57 EDT 2020 + [ 0.000000] earlycon: sifive0 at MMIO 0x0000000038000000 (options '115200n8') + [ 0.000000] printk: bootconsole [sifive0] enabled + [ 0.000000] Zone ranges: + [ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000807fffff] + [ 0.000000] Normal empty + [ 0.000000] Movable zone start for each node + [ 0.000000] Early memory node ranges + [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000807fffff] + [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000807fffff] + [ 0.000000] riscv: ISA extensions acdfgim + [ 0.000000] riscv: ELF capabilities acdfim + [ 0.000000] percpu: max_distance=0x18000 too large for vmalloc space 0x0 + [ 0.000000] percpu: Embedded 12 pages/cpu s18848 r0 d30304 u49152 + [ 0.000000] Built 1 zonelists, mobility grouping off. Total pages: 2020 + [ 0.000000] Kernel command line: earlycon console=ttySIF0 + [ 0.000000] Dentry cache hash table entries: 1024 (order: 1, 8192 bytes, linear) + [ 0.000000] Inode-cache hash table entries: 512 (order: 0, 4096 bytes, linear) + [ 0.000000] Sorting __ex_table... + [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off + [ 0.000000] Memory: 6004K/8192K available (1139K kernel code, 126K rwdata, 198K rodata, 90K init, 81K bss, 2188K reserved, 0K cma-reserved) + [ 0.000000] rcu: Hierarchical RCU implementation. + [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. + [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 + [ 0.000000] riscv-intc: 64 local interrupts mapped + [ 0.000000] plic: interrupt-controller@C000000: mapped 65 interrupts with 2 handlers for 2 contexts. + [ 0.000000] random: get_random_bytes called from 0x00000000800019a8 with crng_init=0 + [ 0.000000] k210-clk: clock-controller + [ 0.000000] k210-clk: clock-controller: fixed-rate 26 MHz osc base clock + [ 0.000000] clint: clint@2000000: timer running at 7800000 Hz + [ 0.000000] clocksource: clint_clocksource: mask: 0xffffffffffffffff max_cycles: 0x3990be68b, max_idle_ns: 881590404272 ns + [ 0.000014] sched_clock: 64 bits at 7MHz, resolution 128ns, wraps every 4398046511054ns + [ 0.008450] Console: colour dummy device 80x25 + [ 0.012494] Calibrating delay loop (skipped), value calculated using timer frequency.. 15.60 BogoMIPS (lpj=31200) + [ 0.022693] pid_max: default: 4096 minimum: 301 + [ 0.027352] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear) + [ 0.034428] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear) + [ 0.045099] rcu: Hierarchical SRCU implementation. + [ 0.050048] smp: Bringing up secondary CPUs ... + [ 0.055417] smp: Brought up 1 node, 2 CPUs + [ 0.059602] devtmpfs: initialized + [ 0.082796] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns + [ 0.091820] futex hash table entries: 16 (order: -2, 1024 bytes, linear) + [ 0.098507] pinctrl core: initialized pinctrl subsystem + [ 0.140938] clocksource: Switched to clocksource clint_clocksource + [ 0.247216] workingset: timestamp_bits=62 max_order=11 bucket_order=0 + [ 0.277392] k210-fpioa 502b0000.pinmux: K210 FPIOA pin controller + [ 0.291724] k210-sysctl 50440000.syscon: K210 system controller + [ 0.305317] k210-rst 50440000.syscon:reset-controller: K210 reset controller + [ 0.313808] 38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1, base_baud = 115200) is a SiFive UART v0 + [ 0.322712] printk: console [ttySIF0] enabled + [ 0.322712] printk: console [ttySIF0] enabled + [ 0.331328] printk: bootconsole [sifive0] disabled + [ 0.331328] printk: bootconsole [sifive0] disabled + [ 0.353347] Freeing unused kernel memory: 88K + [ 0.357004] This architecture does not have kernel memory protection. + [ 0.363397] Run /init as init process + +Loading, Booting, and Storing Images +------------------------------------ + +.. _loading: + Loading Images ^^^^^^^^^^^^^^ -To load a kernel, transfer it over serial. +Serial +"""""" + +Use the ``loady`` command to load images over serial. .. code-block:: none - => loady 80000000 1500000 + => loady $loadaddr 1500000 ## Switch baudrate to 1500000 bps and press ENTER ... *** baud: 1500000 @@ -150,6 +252,61 @@ To load a kernel, transfer it over serial. *** baud: 115200 *** => +This command does not set ``$filesize``, so it may need to be set manually. + +SPI Flash +""""""""" + +To load an image off of SPI flash, first set up a partition as described in +:ref:`partitions`. Then, use ``mtd`` to load that partition + +.. code-block:: none + + => sf probe + SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB + => mtd read linux $loadaddr + Reading 2097152 byte(s) at offset 0x00000000 + +This command does not set ``$filesize``, so it may need to be set manually. + +MMC +""" + +The MMC device number is 0. To list partitions on the device, use ``part``: + +.. code-block:: none + + => part list mmc 0 + + Partition Map for MMC device 0 -- Partition Type: EFI + + Part Start LBA End LBA Name + Attributes + Type GUID + Partition GUID + 1 0x00000800 0x039effde "boot" + attrs: 0x0000000000000000 + type: c12a7328-f81f-11d2-ba4b-00a0c93ec93b + guid: 96161f7d-7113-4cc7-9a24-08ab7fc5cb72 + +To list files, use ``ls``: + +.. code-block:: none + + => ls mmc 0:1 + 4096 . + 4096 .. + 16384 lost+found + 13428 k210.dtb + 1827380 uImage + +To load a file, use ``load``: + +.. code-block:: none + + => load mmc 0:1 $loadaddr uImage + 1827380 bytes read in 1049 ms (1.7 MiB/s) + Running Programs ^^^^^^^^^^^^^^^^ @@ -160,20 +317,6 @@ To run a bare binary, use the ``go`` command: .. code-block:: none - => loady - ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... - C - *** file: ./examples/standalone/hello_world.bin - $ sz -vv ./examples/standalone/hello_world.bin - Sending: hello_world.bin - Bytes Sent: 4864 BPS:649 - Sending: - Ymodem sectors/kbytes sent: 0/ 0k - Transfer complete - - *** exit status: 0 *** - (CAN) packets, 5 retries - ## Total Size = 0x000012f8 = 4856 Bytes => go 80000000 ## Starting application at 0x80000000 ... Example expects ABI version 9 @@ -184,51 +327,127 @@ To run a bare binary, use the ``go`` command: argv[1] = "" Hit any key to exit ... +Note that this will only start a program on one hart. As-of this writing it is +only possible to start a program on multiple harts using the ``bootm`` command. + Legacy Images """"""""""""" -To run legacy images, use the ``bootm`` command: +To create a legacy image, use ``tools/mkimage``: .. code-block:: none - $ tools/mkimage -A riscv -O u-boot -T standalone -C none -a 80000000 -e 80000000 -d examples/standalone/hello_world.bin hello_world.img - Image Name: - Created: Thu Mar 5 12:04:10 2020 - Image Type: RISC-V U-Boot Standalone Program (uncompressed) - Data Size: 4856 Bytes = 4.74 KiB = 0.00 MiB + $ tools/mkimage -A riscv -O linux -T kernel -C none -a 0x80000000 -e 0x80000000 -n linux -d ../linux-git/arch/riscv/boot/Image uImage + Image Name: linux + Created: Fri Oct 16 17:36:32 2020 + Image Type: RISC-V Linux Kernel Image (uncompressed) + Data Size: 1827316 Bytes = 1784.49 KiB = 1.74 MiB Load Address: 80000000 Entry Point: 80000000 - $ picocom -b 115200 /dev/ttyUSB0 - => loady - ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... - C - *** file: hello_world.img - $ sz -vv hello_world.img - Sending: hello_world.img - Bytes Sent: 4992 BPS:665 - Sending: - Ymodem sectors/kbytes sent: 0/ 0k - Transfer complete +The ``bootm`` command also requires an FDT, even if the image doesn't require +one. After loading the image to ``$loadaddr`` and the FDT to ``$fdt_addr_r``, +boot with: - *** exit status: 0 *** - CAN) packets, 3 retries - ## Total Size = 0x00001338 = 4920 Bytes - => bootm - ## Booting kernel from Legacy Image at 80000000 ... - Image Name: - Image Type: RISC-V U-Boot Standalone Program (uncompressed) - Data Size: 4856 Bytes = 4.7 KiB +.. code-block:: none + + => bootm $loadaddr - $fdt_addr_r + ## Booting kernel from Legacy Image at 80060000 ... + Image Name: linux + Image Type: RISC-V Linux Kernel Image (uncompressed) + Data Size: 1827316 Bytes = 1.7 MiB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK - Loading Standalone Program - Example expects ABI version 9 - Actual U-Boot ABI version 9 - Hello World - argc = 0 - argv[0] = "" - Hit any key to exit ... + ## Flattened Device Tree blob at 80400000 + Booting using the fdt blob at 0x80400000 + Loading Kernel Image + Loading Device Tree to 00000000803f9000, end 00000000803ff473 ... OK + + Starting kernel ... + +The FDT is verified after the kernel is relocated, so it must be loaded high +enough so that it won't be overwritten. The default values for ``$loadaddr`` +and ``$fdt_addr_r`` should provide ample headroom for most use-cases. + +Flashing Images +^^^^^^^^^^^^^^^ + +SPI Flash +""""""""" + +To flash data to SPI flash, first load it using one of the methods in +:ref:`loading`. Addiotionally, create some partitions as described in +:ref:`partitions`. Then use the ``mtd`` command: + +.. code-block:: none + + => sf probe + SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB + => mtd write linux $loadaddr 0 $filesize + Writing 2478162 byte(s) at offset 0x00000000 + +Note that in order to write a bootable image, a header and tailer must be added. + +MMC +""" + +MMC writes are unsupported for now. + +SPI Flash +^^^^^^^^^ + +Sipeed MAIX boards typically provide around 16 MiB of SPI NOR flash. U-Boot is +stored in the first 1 MiB or so of this flash. U-Boot's environment is stored at +the end of flash. + +.. _partitions: + +Partitions +"""""""""" + +There is no set data layout. The default partition layout only allocates +partitions for U-Boot and its default environment + +.. code-block:: none + + => mtd list + List of MTD devices: + * nor0 + - type: NOR flash + - block size: 0x1000 bytes + - min I/O: 0x1 bytes + - 0x000000000000-0x000001000000 : "nor0" + - 0x000000000000-0x000000100000 : "u-boot" + - 0x000000fff000-0x000001000000 : "env" + +As an example, to allocate 2MiB for Linux and (almost) 13 MiB for other data, +set the ``mtdparts`` like: + +.. code-block:: none + + => env set mtdparts nor0:1M(u-boot),2M(linux),0xcff000(data),0x1000@0xfff000(env) + => mtd list + List of MTD devices: + * nor0 + - type: NOR flash + - block size: 0x1000 bytes + - min I/O: 0x1 bytes + - 0x000000000000-0x000001000000 : "nor0" + - 0x000000000000-0x000000100000 : "u-boot" + - 0x000000100000-0x000000300000 : "linux" + - 0x000000300000-0x000000fff000 : "data" + - 0x000000fff000-0x000001000000 : "env" + +To make these changes permanent, save the environment: + +.. code-block:: none + + => env save + Saving Environment to SPIFlash... Erasing SPI flash...Writing to SPI flash...done + OK + +U-Boot will always load the environment from the last 4 KiB of flash. Pin Assignment -------------- diff --git a/include/configs/sipeed-maix.h b/include/configs/sipeed-maix.h index 36ff522e4b68fd8d4f9893c1fbac204115a2bd64..08acb25075b0d352c50761f9c7538b74df35548f 100644 --- a/include/configs/sipeed-maix.h +++ b/include/configs/sipeed-maix.h @@ -24,10 +24,13 @@ #ifndef CONFIG_EXTRA_ENV_SETTINGS #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x80060000\0" \ - "fdt_addr_r=0x80028000\0" \ + "fdt_addr_r=0x80400000\0" \ "scriptaddr=0x80020000\0" \ "kernel_addr_r=0x80060000\0" \ - "fdtfile=kendryte/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" + "fdtfile=kendryte/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ + "k210_bootcmd=load mmc 0:1 $loadaddr /uImage && " \ + "load mmc 0:1 $fdt_addr_r /k210.dtb && " \ + "bootm $loadaddr - $fdt_addr_r\0" #endif #endif /* CONFIGS_SIPEED_MAIX_H */