diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index bb979550c440f47e761549029d9738ffb75f8fb7..59a2713cb2da8b242cad31f3db7df503cee27874 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -893,7 +893,8 @@ dtb-$(CONFIG_STM32MP15x) += \ stm32mp157c-dk2.dtb \ stm32mp157c-ed1.dtb \ stm32mp157c-ev1.dtb \ - stm32mp15xx-dhcom-pdk2.dtb + stm32mp15xx-dhcom-pdk2.dtb \ + stm32mp15xx-dhcor-avenger96.dtb dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \ diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi index 53df840f85f2b1d9e0574532adc0d34164ae7da9..29acdc4afdabeb1ce1292b92d231719e2dfaab96 100644 --- a/arch/arm/dts/stm32mp15-pinctrl.dtsi +++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi @@ -162,6 +162,57 @@ }; }; + ethernet0_rgmii_pins_b: rgmii-1 { + pins1 { + pinmux = , /* ETH_RGMII_CLK125 */ + , /* ETH_RGMII_GTX_CLK */ + , /* ETH_RGMII_TXD0 */ + , /* ETH_RGMII_TXD1 */ + , /* ETH_RGMII_TXD2 */ + , /* ETH_RGMII_TXD3 */ + , /* ETH_RGMII_TX_CTL */ + ; /* ETH_MDC */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + pins2 { + pinmux = ; /* ETH_MDIO */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins3 { + pinmux = , /* ETH_RGMII_RXD0 */ + , /* ETH_RGMII_RXD1 */ + , /* ETH_RGMII_RXD2 */ + , /* ETH_RGMII_RXD3 */ + , /* ETH_RGMII_RX_CLK */ + ; /* ETH_RGMII_RX_CTL */ + bias-disable; + }; + }; + + ethernet0_rgmii_pins_sleep_b: rgmii-sleep-1 { + pins1 { + pinmux = , /* ETH_RGMII_CLK125 */ + , /* ETH_RGMII_GTX_CLK */ + , /* ETH_RGMII_TXD0 */ + , /* ETH_RGMII_TXD1 */ + , /* ETH_RGMII_TXD2 */ + , /* ETH_RGMII_TXD3 */ + , /* ETH_RGMII_TX_CTL */ + , /* ETH_MDIO */ + , /* ETH_MDC */ + , /* ETH_RGMII_RXD0 */ + , /* ETH_RGMII_RXD1 */ + , /* ETH_RGMII_RXD2 */ + , /* ETH_RGMII_RXD3 */ + , /* ETH_RGMII_RX_CLK */ + ; /* ETH_RGMII_RX_CTL */ + }; + }; + fmc_pins_a: fmc-0 { pins1 { pinmux = , /* FMC_NOE */ @@ -815,6 +866,30 @@ }; }; + sdmmc1_dir_pins_b: sdmmc1-dir-1 { + pins1 { + pinmux = , /* SDMMC1_D0DIR */ + , /* SDMMC1_D123DIR */ + ; /* SDMMC1_CDIR */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + pins2{ + pinmux = ; /* SDMMC1_CKIN */ + bias-pull-up; + }; + }; + + sdmmc1_dir_sleep_pins_b: sdmmc1-dir-sleep-1 { + pins { + pinmux = , /* SDMMC1_D0DIR */ + , /* SDMMC1_D123DIR */ + , /* SDMMC1_CDIR */ + ; /* SDMMC1_CKIN */ + }; + }; + sdmmc2_b4_pins_a: sdmmc2-b4-0 { pins1 { pinmux = , /* SDMMC2_D0 */ @@ -933,6 +1008,27 @@ }; }; + sdmmc2_d47_pins_b: sdmmc2-d47-1 { + pins { + pinmux = , /* SDMMC2_D4 */ + , /* SDMMC2_D5 */ + , /* SDMMC2_D6 */ + ; /* SDMMC2_D7 */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + }; + + sdmmc2_d47_sleep_pins_b: sdmmc2-d47-sleep-1 { + pins { + pinmux = , /* SDMMC2_D4 */ + , /* SDMMC2_D5 */ + , /* SDMMC2_D6 */ + ; /* SDMMC2_D7 */ + }; + }; + sdmmc3_b4_pins_a: sdmmc3-b4-0 { pins1 { pinmux = , /* SDMMC3_D0 */ diff --git a/arch/arm/dts/stm32mp157-pinctrl.dtsi b/arch/arm/dts/stm32mp157-pinctrl.dtsi deleted file mode 100644 index 422dad1ddd27825a69f04cf7a966c1e1774a8d16..0000000000000000000000000000000000000000 --- a/arch/arm/dts/stm32mp157-pinctrl.dtsi +++ /dev/null @@ -1,1153 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) -/* - * Copyright (C) STMicroelectronics 2017 - All Rights Reserved - * Author: Ludovic Barre for STMicroelectronics. - */ -#include - -/ { - soc { - pinctrl: pin-controller@50002000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32mp157-pinctrl"; - ranges = <0 0x50002000 0xa400>; - interrupt-parent = <&exti>; - st,syscfg = <&exti 0x60 0xff>; - hwlocks = <&hwspinlock 0>; - pins-are-numbered; - - gpioa: gpio@50002000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x0 0x400>; - clocks = <&rcc GPIOA>; - st,bank-name = "GPIOA"; - status = "disabled"; - }; - - gpiob: gpio@50003000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x1000 0x400>; - clocks = <&rcc GPIOB>; - st,bank-name = "GPIOB"; - status = "disabled"; - }; - - gpioc: gpio@50004000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x2000 0x400>; - clocks = <&rcc GPIOC>; - st,bank-name = "GPIOC"; - status = "disabled"; - }; - - gpiod: gpio@50005000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x3000 0x400>; - clocks = <&rcc GPIOD>; - st,bank-name = "GPIOD"; - status = "disabled"; - }; - - gpioe: gpio@50006000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x4000 0x400>; - clocks = <&rcc GPIOE>; - st,bank-name = "GPIOE"; - status = "disabled"; - }; - - gpiof: gpio@50007000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x5000 0x400>; - clocks = <&rcc GPIOF>; - st,bank-name = "GPIOF"; - status = "disabled"; - }; - - gpiog: gpio@50008000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x6000 0x400>; - clocks = <&rcc GPIOG>; - st,bank-name = "GPIOG"; - status = "disabled"; - }; - - gpioh: gpio@50009000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x7000 0x400>; - clocks = <&rcc GPIOH>; - st,bank-name = "GPIOH"; - status = "disabled"; - }; - - gpioi: gpio@5000a000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x8000 0x400>; - clocks = <&rcc GPIOI>; - st,bank-name = "GPIOI"; - status = "disabled"; - }; - - gpioj: gpio@5000b000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x9000 0x400>; - clocks = <&rcc GPIOJ>; - st,bank-name = "GPIOJ"; - status = "disabled"; - }; - - gpiok: gpio@5000c000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0xa000 0x400>; - clocks = <&rcc GPIOK>; - st,bank-name = "GPIOK"; - status = "disabled"; - }; - - adc12_ain_pins_a: adc12-ain-0 { - pins { - pinmux = , /* ADC1 in13 */ - , /* ADC1 in6 */ - , /* ADC2 in2 */ - ; /* ADC2 in6 */ - }; - }; - - adc12_usb_cc_pins_a: adc12-usb-cc-pins-0 { - pins { - pinmux = , /* ADC12 in18 */ - ; /* ADC12 in19 */ - }; - }; - - cec_pins_a: cec-0 { - pins { - pinmux = ; - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - cec_pins_sleep_a: cec-sleep-0 { - pins { - pinmux = ; /* HDMI_CEC */ - }; - }; - - cec_pins_b: cec-1 { - pins { - pinmux = ; - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - cec_pins_sleep_b: cec-sleep-1 { - pins { - pinmux = ; /* HDMI_CEC */ - }; - }; - - dac_ch1_pins_a: dac-ch1 { - pins { - pinmux = ; - }; - }; - - dac_ch2_pins_a: dac-ch2 { - pins { - pinmux = ; - }; - }; - - dcmi_pins_a: dcmi-0 { - pins { - pinmux = ,/* DCMI_HSYNC */ - ,/* DCMI_VSYNC */ - ,/* DCMI_PIXCLK */ - ,/* DCMI_D0 */ - ,/* DCMI_D1 */ - ,/* DCMI_D2 */ - ,/* DCMI_D3 */ - ,/* DCMI_D4 */ - ,/* DCMI_D5 */ - ,/* DCMI_D6 */ - ,/* DCMI_D7 */ - ,/* DCMI_D8 */ - ,/* DCMI_D9 */ - ,/* DCMI_D10 */ - ;/* DCMI_D11 */ - bias-disable; - }; - }; - - dcmi_sleep_pins_a: dcmi-sleep-0 { - pins { - pinmux = ,/* DCMI_HSYNC */ - ,/* DCMI_VSYNC */ - ,/* DCMI_PIXCLK */ - ,/* DCMI_D0 */ - ,/* DCMI_D1 */ - ,/* DCMI_D2 */ - ,/* DCMI_D3 */ - ,/* DCMI_D4 */ - ,/* DCMI_D5 */ - ,/* DCMI_D6 */ - ,/* DCMI_D7 */ - ,/* DCMI_D8 */ - ,/* DCMI_D9 */ - ,/* DCMI_D10 */ - ;/* DCMI_D11 */ - }; - }; - - ethernet0_rgmii_pins_a: rgmii-0 { - pins1 { - pinmux = , /* ETH_RGMII_CLK125 */ - , /* ETH_RGMII_GTX_CLK */ - , /* ETH_RGMII_TXD0 */ - , /* ETH_RGMII_TXD1 */ - , /* ETH_RGMII_TXD2 */ - , /* ETH_RGMII_TXD3 */ - , /* ETH_RGMII_TX_CTL */ - ; /* ETH_MDC */ - bias-disable; - drive-push-pull; - slew-rate = <2>; - }; - pins2 { - pinmux = ; /* ETH_MDIO */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins3 { - pinmux = , /* ETH_RGMII_RXD0 */ - , /* ETH_RGMII_RXD1 */ - , /* ETH_RGMII_RXD2 */ - , /* ETH_RGMII_RXD3 */ - , /* ETH_RGMII_RX_CLK */ - ; /* ETH_RGMII_RX_CTL */ - bias-disable; - }; - }; - - ethernet0_rgmii_pins_sleep_a: rgmii-sleep-0 { - pins1 { - pinmux = , /* ETH_RGMII_CLK125 */ - , /* ETH_RGMII_GTX_CLK */ - , /* ETH_RGMII_TXD0 */ - , /* ETH_RGMII_TXD1 */ - , /* ETH_RGMII_TXD2 */ - , /* ETH_RGMII_TXD3 */ - , /* ETH_RGMII_TX_CTL */ - , /* ETH_MDIO */ - , /* ETH_MDC */ - , /* ETH_RGMII_RXD0 */ - , /* ETH_RGMII_RXD1 */ - , /* ETH_RGMII_RXD2 */ - , /* ETH_RGMII_RXD3 */ - , /* ETH_RGMII_RX_CLK */ - ; /* ETH_RGMII_RX_CTL */ - }; - }; - - ethernet0_rgmii_pins_b: rgmii-1 { - pins1 { - pinmux = , /* ETH_RGMII_CLK125 */ - , /* ETH_RGMII_GTX_CLK */ - , /* ETH_RGMII_TXD0 */ - , /* ETH_RGMII_TXD1 */ - , /* ETH_RGMII_TXD2 */ - , /* ETH_RGMII_TXD3 */ - , /* ETH_RGMII_TX_CTL */ - ; /* ETH_MDC */ - bias-disable; - drive-push-pull; - slew-rate = <2>; - }; - pins2 { - pinmux = ; /* ETH_MDIO */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins3 { - pinmux = , /* ETH_RGMII_RXD0 */ - , /* ETH_RGMII_RXD1 */ - , /* ETH_RGMII_RXD2 */ - , /* ETH_RGMII_RXD3 */ - , /* ETH_RGMII_RX_CLK */ - ; /* ETH_RGMII_RX_CTL */ - bias-disable; - }; - }; - - ethernet0_rgmii_pins_sleep_b: rgmii-sleep-1 { - pins1 { - pinmux = , /* ETH_RGMII_CLK125 */ - , /* ETH_RGMII_GTX_CLK */ - , /* ETH_RGMII_TXD0 */ - , /* ETH_RGMII_TXD1 */ - , /* ETH_RGMII_TXD2 */ - , /* ETH_RGMII_TXD3 */ - , /* ETH_RGMII_TX_CTL */ - , /* ETH_MDIO */ - , /* ETH_MDC */ - , /* ETH_RGMII_RXD0 */ - , /* ETH_RGMII_RXD1 */ - , /* ETH_RGMII_RXD2 */ - , /* ETH_RGMII_RXD3 */ - , /* ETH_RGMII_RX_CLK */ - ; /* ETH_RGMII_RX_CTL */ - }; - }; - - fmc_pins_a: fmc-0 { - pins1 { - pinmux = , /* FMC_NOE */ - , /* FMC_NWE */ - , /* FMC_A16_FMC_CLE */ - , /* FMC_A17_FMC_ALE */ - , /* FMC_D0 */ - , /* FMC_D1 */ - , /* FMC_D2 */ - , /* FMC_D3 */ - , /* FMC_D4 */ - , /* FMC_D5 */ - , /* FMC_D6 */ - , /* FMC_D7 */ - ; /* FMC_NE2_FMC_NCE */ - bias-disable; - drive-push-pull; - slew-rate = <1>; - }; - pins2 { - pinmux = ; /* FMC_NWAIT */ - bias-pull-up; - }; - }; - - fmc_sleep_pins_a: fmc-sleep-0 { - pins { - pinmux = , /* FMC_NOE */ - , /* FMC_NWE */ - , /* FMC_A16_FMC_CLE */ - , /* FMC_A17_FMC_ALE */ - , /* FMC_D0 */ - , /* FMC_D1 */ - , /* FMC_D2 */ - , /* FMC_D3 */ - , /* FMC_D4 */ - , /* FMC_D5 */ - , /* FMC_D6 */ - , /* FMC_D7 */ - , /* FMC_NWAIT */ - ; /* FMC_NE2_FMC_NCE */ - }; - }; - - i2c1_pins_a: i2c1-0 { - pins { - pinmux = , /* I2C1_SCL */ - ; /* I2C1_SDA */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - i2c1_pins_sleep_a: i2c1-1 { - pins { - pinmux = , /* I2C1_SCL */ - ; /* I2C1_SDA */ - }; - }; - - i2c1_pins_b: i2c1-2 { - pins { - pinmux = , /* I2C1_SCL */ - ; /* I2C1_SDA */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - i2c1_pins_sleep_b: i2c1-3 { - pins { - pinmux = , /* I2C1_SCL */ - ; /* I2C1_SDA */ - }; - }; - - i2c2_pins_a: i2c2-0 { - pins { - pinmux = , /* I2C2_SCL */ - ; /* I2C2_SDA */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - i2c2_pins_sleep_a: i2c2-1 { - pins { - pinmux = , /* I2C2_SCL */ - ; /* I2C2_SDA */ - }; - }; - - i2c2_pins_b1: i2c2-2 { - pins { - pinmux = ; /* I2C2_SDA */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - i2c2_pins_sleep_b1: i2c2-3 { - pins { - pinmux = ; /* I2C2_SDA */ - }; - }; - - i2c5_pins_a: i2c5-0 { - pins { - pinmux = , /* I2C5_SCL */ - ; /* I2C5_SDA */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - i2c5_pins_sleep_a: i2c5-1 { - pins { - pinmux = , /* I2C5_SCL */ - ; /* I2C5_SDA */ - - }; - }; - - i2s2_pins_a: i2s2-0 { - pins { - pinmux = , /* I2S2_SDO */ - , /* I2S2_WS */ - ; /* I2S2_CK */ - slew-rate = <1>; - drive-push-pull; - bias-disable; - }; - }; - - i2s2_pins_sleep_a: i2s2-1 { - pins { - pinmux = , /* I2S2_SDO */ - , /* I2S2_WS */ - ; /* I2S2_CK */ - }; - }; - - ltdc_pins_a: ltdc-a-0 { - pins { - pinmux = , /* LCD_CLK */ - , /* LCD_HSYNC */ - , /* LCD_VSYNC */ - , /* LCD_DE */ - , /* LCD_R0 */ - , /* LCD_R1 */ - , /* LCD_R2 */ - , /* LCD_R3 */ - , /* LCD_R4 */ - , /* LCD_R5 */ - , /* LCD_R6 */ - , /* LCD_R7 */ - , /* LCD_G0 */ - , /* LCD_G1 */ - , /* LCD_G2 */ - , /* LCD_G3 */ - , /* LCD_G4 */ - , /* LCD_G5 */ - , /* LCD_G6 */ - , /* LCD_G7 */ - , /* LCD_B0 */ - , /* LCD_B1 */ - , /* LCD_B2 */ - , /* LCD_B3 */ - , /* LCD_B4 */ - , /* LCD_B5 */ - , /* LCD_B6 */ - ; /* LCD_B7 */ - bias-disable; - drive-push-pull; - slew-rate = <1>; - }; - }; - - ltdc_pins_sleep_a: ltdc-a-1 { - pins { - pinmux = , /* LCD_CLK */ - , /* LCD_HSYNC */ - , /* LCD_VSYNC */ - , /* LCD_DE */ - , /* LCD_R0 */ - , /* LCD_R1 */ - , /* LCD_R2 */ - , /* LCD_R3 */ - , /* LCD_R4 */ - , /* LCD_R5 */ - , /* LCD_R6 */ - , /* LCD_R7 */ - , /* LCD_G0 */ - , /* LCD_G1 */ - , /* LCD_G2 */ - , /* LCD_G3 */ - , /* LCD_G4 */ - , /* LCD_G5 */ - , /* LCD_G6 */ - , /* LCD_G7 */ - , /* LCD_B0 */ - , /* LCD_B1 */ - , /* LCD_B2 */ - , /* LCD_B3 */ - , /* LCD_B4 */ - , /* LCD_B5 */ - , /* LCD_B6 */ - ; /* LCD_B7 */ - }; - }; - - ltdc_pins_b: ltdc-b-0 { - pins { - pinmux = , /* LCD_CLK */ - , /* LCD_HSYNC */ - , /* LCD_VSYNC */ - , /* LCD_DE */ - , /* LCD_R0 */ - , /* LCD_R1 */ - , /* LCD_R2 */ - , /* LCD_R3 */ - , /* LCD_R4 */ - , /* LCD_R5 */ - , /* LCD_R6 */ - , /* LCD_R7 */ - , /* LCD_G0 */ - , /* LCD_G1 */ - , /* LCD_G2 */ - , /* LCD_G3 */ - , /* LCD_G4 */ - , /* LCD_G5 */ - , /* LCD_G6 */ - , /* LCD_G7 */ - , /* LCD_B0 */ - , /* LCD_B1 */ - , /* LCD_B2 */ - , /* LCD_B3 */ - , /* LCD_B4 */ - , /* LCD_B5 */ - , /* LCD_B6 */ - ; /* LCD_B7 */ - bias-disable; - drive-push-pull; - slew-rate = <1>; - }; - }; - - ltdc_pins_sleep_b: ltdc-b-1 { - pins { - pinmux = , /* LCD_CLK */ - , /* LCD_HSYNC */ - , /* LCD_VSYNC */ - , /* LCD_DE */ - , /* LCD_R0 */ - , /* LCD_R1 */ - , /* LCD_R2 */ - , /* LCD_R3 */ - , /* LCD_R4 */ - , /* LCD_R5 */ - , /* LCD_R6 */ - , /* LCD_R7 */ - , /* LCD_G0 */ - , /* LCD_G1 */ - , /* LCD_G2 */ - , /* LCD_G3 */ - , /* LCD_G4 */ - , /* LCD_G5 */ - , /* LCD_G6 */ - , /* LCD_G7 */ - , /* LCD_B0 */ - , /* LCD_B1 */ - , /* LCD_B2 */ - , /* LCD_B3 */ - , /* LCD_B4 */ - , /* LCD_B5 */ - , /* LCD_B6 */ - ; /* LCD_B7 */ - }; - }; - - m_can1_pins_a: m-can1-0 { - pins1 { - pinmux = ; /* CAN1_TX */ - slew-rate = <1>; - drive-push-pull; - bias-disable; - }; - pins2 { - pinmux = ; /* CAN1_RX */ - bias-disable; - }; - }; - - m_can1_sleep_pins_a: m_can1-sleep-0 { - pins { - pinmux = , /* CAN1_TX */ - ; /* CAN1_RX */ - }; - }; - - pwm2_pins_a: pwm2-0 { - pins { - pinmux = ; /* TIM2_CH4 */ - bias-pull-down; - drive-push-pull; - slew-rate = <0>; - }; - }; - - pwm8_pins_a: pwm8-0 { - pins { - pinmux = ; /* TIM8_CH4 */ - bias-pull-down; - drive-push-pull; - slew-rate = <0>; - }; - }; - - pwm12_pins_a: pwm12-0 { - pins { - pinmux = ; /* TIM12_CH1 */ - bias-pull-down; - drive-push-pull; - slew-rate = <0>; - }; - }; - - qspi_clk_pins_a: qspi-clk-0 { - pins { - pinmux = ; /* QSPI_CLK */ - bias-disable; - drive-push-pull; - slew-rate = <3>; - }; - }; - - qspi_clk_sleep_pins_a: qspi-clk-sleep-0 { - pins { - pinmux = ; /* QSPI_CLK */ - }; - }; - - qspi_bk1_pins_a: qspi-bk1-0 { - pins1 { - pinmux = , /* QSPI_BK1_IO0 */ - , /* QSPI_BK1_IO1 */ - , /* QSPI_BK1_IO2 */ - ; /* QSPI_BK1_IO3 */ - bias-disable; - drive-push-pull; - slew-rate = <1>; - }; - pins2 { - pinmux = ; /* QSPI_BK1_NCS */ - bias-pull-up; - drive-push-pull; - slew-rate = <1>; - }; - }; - - qspi_bk1_sleep_pins_a: qspi-bk1-sleep-0 { - pins { - pinmux = , /* QSPI_BK1_IO0 */ - , /* QSPI_BK1_IO1 */ - , /* QSPI_BK1_IO2 */ - , /* QSPI_BK1_IO3 */ - ; /* QSPI_BK1_NCS */ - }; - }; - - qspi_bk2_pins_a: qspi-bk2-0 { - pins1 { - pinmux = , /* QSPI_BK2_IO0 */ - , /* QSPI_BK2_IO1 */ - , /* QSPI_BK2_IO2 */ - ; /* QSPI_BK2_IO3 */ - bias-disable; - drive-push-pull; - slew-rate = <1>; - }; - pins2 { - pinmux = ; /* QSPI_BK2_NCS */ - bias-pull-up; - drive-push-pull; - slew-rate = <1>; - }; - }; - - qspi_bk2_sleep_pins_a: qspi-bk2-sleep-0 { - pins { - pinmux = , /* QSPI_BK2_IO0 */ - , /* QSPI_BK2_IO1 */ - , /* QSPI_BK2_IO2 */ - , /* QSPI_BK2_IO3 */ - ; /* QSPI_BK2_NCS */ - }; - }; - - sai2a_pins_a: sai2a-0 { - pins { - pinmux = , /* SAI2_SCK_A */ - , /* SAI2_SD_A */ - , /* SAI2_FS_A */ - ; /* SAI2_MCLK_A */ - slew-rate = <0>; - drive-push-pull; - bias-disable; - }; - }; - - sai2a_sleep_pins_a: sai2a-1 { - pins { - pinmux = , /* SAI2_SCK_A */ - , /* SAI2_SD_A */ - , /* SAI2_FS_A */ - ; /* SAI2_MCLK_A */ - }; - }; - - sai2b_pins_a: sai2b-0 { - pins1 { - pinmux = , /* SAI2_SCK_B */ - , /* SAI2_FS_B */ - ; /* SAI2_MCLK_B */ - slew-rate = <0>; - drive-push-pull; - bias-disable; - }; - pins2 { - pinmux = ; /* SAI2_SD_B */ - bias-disable; - }; - }; - - sai2b_sleep_pins_a: sai2b-1 { - pins { - pinmux = , /* SAI2_SD_B */ - , /* SAI2_SCK_B */ - , /* SAI2_FS_B */ - ; /* SAI2_MCLK_B */ - }; - }; - - sai2b_pins_b: sai2b-2 { - pins { - pinmux = ; /* SAI2_SD_B */ - bias-disable; - }; - }; - - sai2b_sleep_pins_b: sai2b-3 { - pins { - pinmux = ; /* SAI2_SD_B */ - }; - }; - - sai4a_pins_a: sai4a-0 { - pins { - pinmux = ; /* SAI4_SD_A */ - slew-rate = <0>; - drive-push-pull; - bias-disable; - }; - }; - - sai4a_sleep_pins_a: sai4a-1 { - pins { - pinmux = ; /* SAI4_SD_A */ - }; - }; - - sdmmc1_b4_pins_a: sdmmc1-b4-0 { - pins { - pinmux = , /* SDMMC1_D0 */ - , /* SDMMC1_D1 */ - , /* SDMMC1_D2 */ - , /* SDMMC1_D3 */ - , /* SDMMC1_CK */ - ; /* SDMMC1_CMD */ - slew-rate = <3>; - drive-push-pull; - bias-disable; - }; - }; - - sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 { - pins1 { - pinmux = , /* SDMMC1_D0 */ - , /* SDMMC1_D1 */ - , /* SDMMC1_D2 */ - , /* SDMMC1_D3 */ - ; /* SDMMC1_CK */ - slew-rate = <3>; - drive-push-pull; - bias-disable; - }; - pins2{ - pinmux = ; /* SDMMC1_CMD */ - slew-rate = <3>; - drive-open-drain; - bias-disable; - }; - }; - - sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 { - pins { - pinmux = , /* SDMMC1_D0 */ - , /* SDMMC1_D1 */ - , /* SDMMC1_D2 */ - , /* SDMMC1_D3 */ - , /* SDMMC1_CK */ - ; /* SDMMC1_CMD */ - }; - }; - - sdmmc1_dir_pins_a: sdmmc1-dir-0 { - pins1 { - pinmux = , /* SDMMC1_D0DIR */ - , /* SDMMC1_D123DIR */ - ; /* SDMMC1_CDIR */ - slew-rate = <3>; - drive-push-pull; - bias-pull-up; - }; - pins2{ - pinmux = ; /* SDMMC1_CKIN */ - bias-pull-up; - }; - }; - - sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 { - pins { - pinmux = , /* SDMMC1_D0DIR */ - , /* SDMMC1_D123DIR */ - , /* SDMMC1_CDIR */ - ; /* SDMMC1_CKIN */ - }; - }; - - sdmmc1_dir_pins_b: sdmmc1-dir-1 { - pins1 { - pinmux = , /* SDMMC1_D0DIR */ - , /* SDMMC1_D123DIR */ - ; /* SDMMC1_CDIR */ - slew-rate = <1>; - drive-push-pull; - bias-pull-up; - }; - pins2{ - pinmux = ; /* SDMMC1_CKIN */ - bias-pull-up; - }; - }; - - sdmmc1_dir_sleep_pins_b: sdmmc1-dir-sleep-1 { - pins { - pinmux = , /* SDMMC1_D0DIR */ - , /* SDMMC1_D123DIR */ - , /* SDMMC1_CDIR */ - ; /* SDMMC1_CKIN */ - }; - }; - - sdmmc2_b4_pins_a: sdmmc2-b4-0 { - pins1 { - pinmux = , /* SDMMC2_D0 */ - , /* SDMMC2_D1 */ - , /* SDMMC2_D2 */ - , /* SDMMC2_D3 */ - ; /* SDMMC2_CMD */ - slew-rate = <1>; - drive-push-pull; - bias-pull-up; - }; - pins2 { - pinmux = ; /* SDMMC2_CK */ - slew-rate = <2>; - drive-push-pull; - bias-pull-up; - }; - }; - - sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 { - pins1 { - pinmux = , /* SDMMC2_D0 */ - , /* SDMMC2_D1 */ - , /* SDMMC2_D2 */ - ; /* SDMMC2_D3 */ - slew-rate = <1>; - drive-push-pull; - bias-pull-up; - }; - pins2 { - pinmux = ; /* SDMMC2_CK */ - slew-rate = <2>; - drive-push-pull; - bias-pull-up; - }; - pins3 { - pinmux = ; /* SDMMC2_CMD */ - slew-rate = <1>; - drive-open-drain; - bias-pull-up; - }; - }; - - sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 { - pins { - pinmux = , /* SDMMC2_D0 */ - , /* SDMMC2_D1 */ - , /* SDMMC2_D2 */ - , /* SDMMC2_D3 */ - , /* SDMMC2_CK */ - ; /* SDMMC2_CMD */ - }; - }; - - sdmmc2_d47_pins_a: sdmmc2-d47-0 { - pins { - pinmux = , /* SDMMC2_D4 */ - , /* SDMMC2_D5 */ - , /* SDMMC2_D6 */ - ; /* SDMMC2_D7 */ - slew-rate = <1>; - drive-push-pull; - bias-pull-up; - }; - }; - - sdmmc2_d47_sleep_pins_a: sdmmc2-d47-sleep-0 { - pins { - pinmux = , /* SDMMC2_D4 */ - , /* SDMMC2_D5 */ - , /* SDMMC2_D6 */ - ; /* SDMMC2_D7 */ - }; - }; - - sdmmc2_d47_pins_b: sdmmc2-d47-1 { - pins { - pinmux = , /* SDMMC2_D4 */ - , /* SDMMC2_D5 */ - , /* SDMMC2_D6 */ - ; /* SDMMC2_D7 */ - slew-rate = <1>; - drive-push-pull; - bias-pull-up; - }; - }; - - sdmmc2_d47_sleep_pins_b: sdmmc2-d47-sleep-1 { - pins { - pinmux = , /* SDMMC2_D4 */ - , /* SDMMC2_D5 */ - , /* SDMMC2_D6 */ - ; /* SDMMC2_D7 */ - }; - }; - - spdifrx_pins_a: spdifrx-0 { - pins { - pinmux = ; /* SPDIF_IN1 */ - bias-disable; - }; - }; - - spdifrx_sleep_pins_a: spdifrx-1 { - pins { - pinmux = ; /* SPDIF_IN1 */ - }; - }; - - spi2_pins_a: spi2-0 { - pins1 { - pinmux = , /* SPI2_SCK */ - , /* SPI2_NSS */ - ; /* SPI2_MOSI */ - bias-disable; - drive-push-pull; - slew-rate = <3>; - }; - pins2 { - pinmux = ; /* SPI2_MISO */ - bias-disable; - }; - }; - - stusb1600_pins_a: stusb1600-0 { - pins { - pinmux = ; - bias-pull-up; - }; - }; - - uart4_pins_a: uart4-0 { - pins1 { - pinmux = ; /* UART4_TX */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = ; /* UART4_RX */ - bias-disable; - }; - }; - - uart4_pins_b: uart4-1 { - pins1 { - pinmux = ; /* UART4_TX */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = ; /* UART4_RX */ - bias-disable; - }; - }; - - uart7_pins_a: uart7-0 { - pins1 { - pinmux = ; /* UART4_TX */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = , /* UART4_RX */ - , /* UART4_CTS */ - ; /* UART4_RTS */ - bias-disable; - }; - }; - }; - - pinctrl_z: pin-controller-z@54004000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32mp157-z-pinctrl"; - ranges = <0 0x54004000 0x400>; - pins-are-numbered; - interrupt-parent = <&exti>; - st,syscfg = <&exti 0x60 0xff>; - hwlocks = <&hwspinlock 0>; - - gpioz: gpio@54004000 { - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0 0x400>; - clocks = <&rcc GPIOZ>; - st,bank-name = "GPIOZ"; - st,bank-ioport = <11>; - status = "disabled"; - }; - - i2c2_pins_b2: i2c2-0 { - pins { - pinmux = ; /* I2C2_SCL */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - i2c2_pins_sleep_b2: i2c2-1 { - pins { - pinmux = ; /* I2C2_SCL */ - }; - }; - - i2c4_pins_a: i2c4-0 { - pins { - pinmux = , /* I2C4_SCL */ - ; /* I2C4_SDA */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - i2c4_pins_sleep_a: i2c4-1 { - pins { - pinmux = , /* I2C4_SCL */ - ; /* I2C4_SDA */ - }; - }; - - spi1_pins_a: spi1-0 { - pins1 { - pinmux = , /* SPI1_SCK */ - ; /* SPI1_MOSI */ - bias-disable; - drive-push-pull; - slew-rate = <1>; - }; - - pins2 { - pinmux = ; /* SPI1_MISO */ - bias-disable; - }; - }; - }; - }; -}; diff --git a/arch/arm/dts/stm32mp157a-avenger96.dts b/arch/arm/dts/stm32mp157a-avenger96.dts index 11e7e6367da9a48231b8b8479dda72872b04c9fc..9c165104fbe546d307d270d8045e6deaac8c5b4f 100644 --- a/arch/arm/dts/stm32mp157a-avenger96.dts +++ b/arch/arm/dts/stm32mp157a-avenger96.dts @@ -4,424 +4,5 @@ * Author: Manivannan Sadhasivam */ -/dts-v1/; - -#include "stm32mp157.dtsi" -#include "stm32mp15-pinctrl.dtsi" -#include "stm32mp157-pinctrl.dtsi" -#include "stm32mp15xxac-pinctrl.dtsi" -#include -#include - -/ { - model = "Arrow Electronics STM32MP157A Avenger96 board"; - compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; - - aliases { - eeprom0 = &eeprom0; - ethernet0 = ðernet0; - mmc0 = &sdmmc1; - serial0 = &uart4; - serial1 = &uart7; - spi0 = &qspi; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@c0000000 { - device_type = "memory"; - reg = <0xc0000000 0x40000000>; - }; - - led { - compatible = "gpio-leds"; - led1 { - label = "green:user0"; - gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - - led2 { - label = "green:user1"; - gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; - }; - - led3 { - label = "green:user2"; - gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc1"; - default-state = "off"; - }; - - led4 { - label = "green:user3"; - gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "none"; - default-state = "off"; - panic-indicator; - }; - - led5 { - label = "yellow:wifi"; - gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "phy0tx"; - default-state = "off"; - }; - - led6 { - label = "blue:bt"; - gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "bluetooth-power"; - default-state = "off"; - }; - }; - - sd_switch: regulator-sd_switch { - compatible = "regulator-gpio"; - regulator-name = "sd_switch"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2900000>; - regulator-type = "voltage"; - regulator-always-on; - - gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - states = <1800000 0x1>, - <2900000 0x0>; - }; - - /* Enpirion EP3A8LQI U2 on the DHCOR */ - vdd_io: regulator-buck-io { - compatible = "regulator-fixed"; - regulator-name = "buck-io"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <&vdd>; - }; -}; - -ðernet0 { - status = "okay"; - pinctrl-0 = <ðernet0_rgmii_pins_b>; - pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>; - pinctrl-names = "default", "sleep"; - phy-mode = "rgmii"; - max-speed = <1000>; - phy-handle = <&phy0>; - phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; - - mdio0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - phy0: ethernet-phy@7 { - reg = <7>; - }; - }; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_b>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&i2c2 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&i2c4 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c4_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; - - pmic: stpmic@33 { - compatible = "st,stpmic1"; - reg = <0x33>; - interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; - interrupt-controller; - #interrupt-cells = <2>; - status = "okay"; - - st,main-control-register = <0x04>; - st,vin-control-register = <0xc0>; - st,usb-control-register = <0x30>; - - regulators { - compatible = "st,stpmic1-regulators"; - - ldo1-supply = <&v3v3>; - ldo2-supply = <&v3v3>; - ldo3-supply = <&vdd_ddr>; - ldo5-supply = <&v3v3>; - ldo6-supply = <&v3v3>; - pwr_sw1-supply = <&bst_out>; - pwr_sw2-supply = <&bst_out>; - - vddcore: buck1 { - regulator-name = "vddcore"; - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd_ddr: buck2 { - regulator-name = "vdd_ddr"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd: buck3 { - regulator-name = "vdd"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - regulator-always-on; - st,mask_reset; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - v3v3: buck4 { - regulator-name = "v3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-over-current-protection; - regulator-initial-mode = <0>; - }; - - vdda: ldo1 { - regulator-name = "vdda"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - interrupts = ; - interrupt-parent = <&pmic>; - }; - - v2v8: ldo2 { - regulator-name = "v2v8"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - interrupts = ; - interrupt-parent = <&pmic>; - }; - - vtt_ddr: ldo3 { - regulator-name = "vtt_ddr"; - regulator-min-microvolt = <500000>; - regulator-max-microvolt = <750000>; - regulator-always-on; - regulator-over-current-protection; - }; - - vdd_usb: ldo4 { - regulator-name = "vdd_usb"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - interrupts = ; - interrupt-parent = <&pmic>; - }; - - vdd_sd: ldo5 { - regulator-name = "vdd_sd"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - interrupts = ; - interrupt-parent = <&pmic>; - regulator-boot-on; - }; - - v1v8: ldo6 { - regulator-name = "v1v8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - interrupts = ; - interrupt-parent = <&pmic>; - regulator-enable-ramp-delay = <300000>; - }; - - vref_ddr: vref_ddr { - regulator-name = "vref_ddr"; - regulator-always-on; - regulator-over-current-protection; - }; - - bst_out: boost { - regulator-name = "bst_out"; - interrupts = ; - interrupt-parent = <&pmic>; - }; - - vbus_otg: pwr_sw1 { - regulator-name = "vbus_otg"; - interrupts = ; - interrupt-parent = <&pmic>; - regulator-active-discharge = <1>; - }; - - vbus_sw: pwr_sw2 { - regulator-name = "vbus_sw"; - interrupts = ; - interrupt-parent = <&pmic>; - regulator-active-discharge = <1>; - }; - }; - - onkey { - compatible = "st,stpmic1-onkey"; - interrupts = , ; - interrupt-names = "onkey-falling", "onkey-rising"; - status = "okay"; - }; - - watchdog { - compatible = "st,stpmic1-wdt"; - status = "disabled"; - }; - }; - - eeprom0: eeprom@53 { - compatible = "atmel,24c02"; - reg = <0x53>; - pagesize = <16>; - }; -}; - -&iwdg2 { - timeout-sec = <32>; - status = "okay"; -}; - -&pwr_regulators { - vdd-supply = <&vdd_io>; - vdd_3v3_usbfs-supply = <&vdd_usb>; -}; - -&qspi { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; - reg = <0x58003000 0x1000>, <0x70000000 0x200000>; - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - - flash0: spi-flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; -}; - -&rng1 { - status = "okay"; -}; - -&rtc { - status = "okay"; -}; - -&sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; - pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; - disable-wp; - st,sig-dir; - st,neg-edge; - st,use-ckin; - sd-uhs-sdr104; - bus-width = <4>; - vmmc-supply = <&vdd_sd>; - vqmmc-supply = <&sd_switch>; - status = "okay"; -}; - -&sdmmc2 { - pinctrl-names = "default"; - pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; - non-removable; - no-sd; - no-sdio; - st,neg-edge; - bus-width = <8>; - vmmc-supply = <&v3v3>; - mmc-ddr-3_3v; - status = "okay"; -}; - -&spi2 { - pinctrl-names = "default"; - pinctrl-0 = <&spi2_pins_a>; - status = "okay"; -}; - -&uart4 { - /* On Low speed expansion header */ - label = "LS-UART1"; - pinctrl-names = "default"; - pinctrl-0 = <&uart4_pins_b>; - status = "okay"; -}; - -&uart7 { - /* On Low speed expansion header */ - label = "LS-UART0"; - pinctrl-names = "default"; - pinctrl-0 = <&uart7_pins_a>; - status = "okay"; -}; - -&usbh_ehci { - phys = <&usbphyc_port0>; - phy-names = "usb"; - status = "okay"; -}; - -&usbotg_hs { - dr_mode = "peripheral"; - phys = <&usbphyc_port1 0>; - phy-names = "usb2-phy"; - status = "okay"; -}; - -&usbphyc { - status = "okay"; -}; - -&usbphyc_port0 { - phy-supply = <&vdd_usb>; -}; - -&usbphyc_port1 { - phy-supply = <&vdd_usb>; -}; +/* This is kept for backward compatibility and will be removed */ +#include "stm32mp15xx-dhcor-avenger96.dts" diff --git a/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi new file mode 100644 index 0000000000000000000000000000000000000000..3f82f207055b631581229fa8e2953345ff94d282 --- /dev/null +++ b/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi @@ -0,0 +1,83 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * Copyright (C) 2020 Marek Vasut + */ + +#include "stm32mp15xx-dhcor-u-boot.dtsi" + +/ { + aliases { + mmc0 = &sdmmc1; + mmc1 = &sdmmc2; + usb0 = &usbotg_hs; + }; + + config { + u-boot,boot-led = "led1"; + u-boot,error-led = "led4"; + }; +}; + +&sdmmc1 { + u-boot,dm-spl; +}; + +&sdmmc1_b4_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&sdmmc1_dir_pins_b { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&sdmmc2 { + u-boot,dm-spl; +}; + +&sdmmc2_b4_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&sdmmc2_d47_pins_b { + u-boot,dm-spl; + pins { + u-boot,dm-spl; + }; +}; + +&uart4 { + u-boot,dm-pre-reloc; +}; + +&uart4_pins_b { + u-boot,dm-pre-reloc; + pins1 { + u-boot,dm-pre-reloc; + }; + pins2 { + u-boot,dm-pre-reloc; + }; +}; + +&usbotg_hs { + u-boot,force-b-session-valid; + hnp-srp-disable; +}; diff --git a/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts b/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts new file mode 100644 index 0000000000000000000000000000000000000000..a6006775637ccbc6d2578d481521a3c719a5b655 --- /dev/null +++ b/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts @@ -0,0 +1,212 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam + * Copyright (C) 2020 Marek Vasut + */ + +/dts-v1/; + +#include "stm32mp15xx-dhcor.dtsi" +#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi" + +/ { + model = "Arrow Electronics STM32MP15xx Avenger96 board"; + compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x"; + + aliases { + eeprom0 = &eeprom0; + ethernet0 = ðernet0; + mmc0 = &sdmmc1; + serial0 = &uart4; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + led { + compatible = "gpio-leds"; + led1 { + label = "green:user0"; + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led2 { + label = "green:user1"; + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led3 { + label = "green:user2"; + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "green:user3"; + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + panic-indicator; + }; + + led5 { + label = "yellow:wifi"; + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; + default-state = "off"; + }; + + led6 { + label = "blue:bt"; + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "bluetooth-power"; + default-state = "off"; + }; + }; + + sd_switch: regulator-sd_switch { + compatible = "regulator-gpio"; + regulator-name = "sd_switch"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-type = "voltage"; + regulator-always-on; + + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + states = <1800000 0x1>, + <2900000 0x0>; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_b>; + pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii"; + max-speed = <1000>; + phy-handle = <&phy0>; + phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@7 { + reg = <7>; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c4 { + eeprom0: eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; + disable-wp; + st,sig-dir; + st,neg-edge; + st,use-ckin; + sd-uhs-sdr104; + bus-width = <4>; + vmmc-supply = <&vdd_sd>; + vqmmc-supply = <&sd_switch>; + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; + non-removable; + no-sd; + no-sdio; + st,neg-edge; + bus-width = <8>; + vmmc-supply = <&v3v3>; + mmc-ddr-3_3v; + status = "okay"; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; +}; + +&uart4 { + /* On Low speed expansion header */ + label = "LS-UART1"; + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_b>; + status = "okay"; +}; + +&uart7 { + /* On Low speed expansion header */ + label = "LS-UART0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + phy-names = "usb"; + status = "okay"; +}; + +&usbotg_hs { + dr_mode = "peripheral"; + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + status = "okay"; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; +}; diff --git a/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi similarity index 71% rename from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi rename to arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi index f2ff7a23c55e33aa8fd16bce9350692099e90c73..5de7b87b9a1b30c6362322a27b6ad8915ef173db 100644 --- a/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi +++ b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi @@ -4,25 +4,13 @@ * * Copyright (C) Linaro Ltd 2019 - All Rights Reserved * Author: Manivannan Sadhasivam + * Copyright (C) 2020 Marek Vasut */ #include #include "stm32mp15-u-boot.dtsi" #include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi" -/ { - aliases { - mmc0 = &sdmmc1; - mmc1 = &sdmmc2; - usb0 = &usbotg_hs; - }; - - config { - u-boot,boot-led = "led1"; - u-boot,error-led = "led4"; - }; -}; - &i2c4 { u-boot,dm-pre-reloc; }; @@ -38,6 +26,10 @@ u-boot,dm-pre-reloc; }; +&qspi { + u-boot,dm-spl; +}; + &rcc { st,clksrc = < CLK_MPU_PLL1P @@ -130,75 +122,11 @@ u-boot,dm-pre-reloc; }; - /* VCO = 480.0 MHz => P = 120, Q = 40, R = 96 */ + /* VCO = 600.0 MHz => P = 100, Q = 50, R = 100 */ pll4: st,pll@3 { compatible = "st,stm32mp1-pll"; reg = <3>; - cfg = < 1 39 3 11 4 PQR(1,1,1) >; - u-boot,dm-pre-reloc; - }; -}; - -&sdmmc1 { - u-boot,dm-spl; -}; - -&sdmmc1_b4_pins_a { - u-boot,dm-spl; - pins1 { - u-boot,dm-spl; - }; - pins2 { - u-boot,dm-spl; - }; -}; - -&sdmmc1_dir_pins_b { - u-boot,dm-spl; - pins1 { - u-boot,dm-spl; - }; - pins2 { - u-boot,dm-spl; - }; -}; - -&sdmmc2 { - u-boot,dm-spl; -}; - -&sdmmc2_b4_pins_a { - u-boot,dm-spl; - pins1 { - u-boot,dm-spl; - }; - pins2 { - u-boot,dm-spl; - }; -}; - -&sdmmc2_d47_pins_b { - u-boot,dm-spl; - pins { - u-boot,dm-spl; - }; -}; - -&uart4 { - u-boot,dm-pre-reloc; -}; - -&uart4_pins_b { - u-boot,dm-pre-reloc; - pins1 { - u-boot,dm-pre-reloc; - }; - pins2 { + cfg = < 1 49 5 11 5 PQR(1,1,1) >; u-boot,dm-pre-reloc; }; }; - -&usbotg_hs { - u-boot,force-b-session-valid; - hnp-srp-disable; -}; diff --git a/arch/arm/dts/stm32mp15xx-dhcor.dtsi b/arch/arm/dts/stm32mp15xx-dhcor.dtsi new file mode 100644 index 0000000000000000000000000000000000000000..97d370e119366ac7c3bdce298c9fa92e12887708 --- /dev/null +++ b/arch/arm/dts/stm32mp15xx-dhcor.dtsi @@ -0,0 +1,232 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam + * Copyright (C) 2020 Marek Vasut + */ +/dts-v1/; + +#include "stm32mp157.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxac-pinctrl.dtsi" +#include +#include + +/ { + aliases { + spi0 = &qspi; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x40000000>; + }; + + /* Enpirion EP3A8LQI U2 on the DHCOR */ + vdd_io: regulator-buck-io { + compatible = "regulator-fixed"; + regulator-name = "buck-io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd>; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + st,main-control-register = <0x04>; + st,vin-control-register = <0xc0>; + st,usb-control-register = <0x30>; + + regulators { + compatible = "st,stpmic1-regulators"; + + ldo1-supply = <&v3v3>; + ldo2-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo5-supply = <&v3v3>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + regulator-always-on; + st,mask_reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + vdda: ldo1 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = ; + interrupt-parent = <&pmic>; + }; + + v2v8: ldo2 { + regulator-name = "v2v8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + interrupts = ; + interrupt-parent = <&pmic>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = ; + interrupt-parent = <&pmic>; + }; + + vdd_sd: ldo5 { + regulator-name = "vdd_sd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = ; + interrupt-parent = <&pmic>; + regulator-boot-on; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = ; + interrupt-parent = <&pmic>; + regulator-enable-ramp-delay = <300000>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = ; + interrupt-parent = <&pmic>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = ; + interrupt-parent = <&pmic>; + regulator-active-discharge = <1>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = ; + interrupt-parent = <&pmic>; + regulator-active-discharge = <1>; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = , ; + interrupt-names = "onkey-falling", "onkey-rising"; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&pwr_regulators { + vdd-supply = <&vdd_io>; + vdd_3v3_usbfs-supply = <&vdd_usb>; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x200000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: spi-flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; diff --git a/configs/stm32mp15_dhcom_basic_defconfig b/configs/stm32mp15_dhcom_basic_defconfig index 683f15e7d58734c3f2189bd89f4a358b47e24b4d..f830feb306894df33fb7d97bc9dae23a3063424a 100644 --- a/configs/stm32mp15_dhcom_basic_defconfig +++ b/configs/stm32mp15_dhcom_basic_defconfig @@ -19,10 +19,7 @@ CONFIG_SPL_MTD_SUPPORT=y CONFIG_SPL_POWER_SUPPORT=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000 CONFIG_SYS_PROMPT="STM32MP> " -# CONFIG_CMD_BOOTD is not set # CONFIG_CMD_ELF is not set -# CONFIG_CMD_IMI is not set -# CONFIG_CMD_XIMG is not set # CONFIG_CMD_EXPORTENV is not set CONFIG_CMD_EEPROM=y CONFIG_CMD_MEMINFO=y diff --git a/doc/board/st/stm32mp1.rst b/doc/board/st/stm32mp1.rst index b7a0fbfd0359a1b9461c53929f9a96622edcd888..b3856be9a151d95f1d61ad2399ed04108b9a48ae 100644 --- a/doc/board/st/stm32mp1.rst +++ b/doc/board/st/stm32mp1.rst @@ -51,11 +51,11 @@ And the necessary drivers Currently the following boards are supported: - + stm32mp157a-avenger96.dts + stm32mp157a-dk1.dts + stm32mp157c-dk2.dts + stm32mp157c-ed1.dts + stm32mp157c-ev1.dts + + stm32mp15xx-dhcor-avenger96.dts Boot Sequences -------------- @@ -153,9 +153,9 @@ the supported device trees for STM32MP15x are: + stm32mp157c-dk2 -+ avenger96: Avenger96 board from Arrow Electronics ++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM - + stm32mp157a-avenger96 + + stm32mp15xx-dhcor-avenger96 Build Procedure --------------- @@ -237,7 +237,7 @@ Build Procedure # export KBUILD_OUTPUT=stm32mp15_basic # make stm32mp15_basic_defconfig - # make DEVICE_TREE=stm32mp157a-avenger96 all + # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all 6. Output files