sf: Add quad read/write commands support

This patch add quad commands support like
- QUAD_PAGE_PROGRAM => for write program
- QUAD_OUTPUT_FAST ->> for read program
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

drivers/mtd/spi/sf_internal.h

@@ -28,6 +28,7 @@
 #define CMD_PAGE_PROGRAM		0x02
 #define CMD_WRITE_DISABLE		0x04
 #define CMD_READ_STATUS			0x05
+#define CMD_QUAD_PAGE_PROGRAM		0x32
 #define CMD_READ_STATUS1		0x35
 #define CMD_WRITE_ENABLE		0x06
 #define CMD_READ_CONFIG			0x35
@@ -38,6 +39,7 @@
 #define CMD_READ_ARRAY_FAST		0x0b
 #define CMD_READ_DUAL_OUTPUT_FAST	0x3b
 #define CMD_READ_DUAL_IO_FAST		0xbb
+#define CMD_READ_QUAD_OUTPUT_FAST	0x6b
 #define CMD_READ_ID			0x9f
 
 /* Bank addr access commands */

drivers/mtd/spi/sf_ops.c

@@ -210,7 +210,7 @@ int spi_flash_cmd_write_ops(struct spi_flash *flash, u32 offset,
 
 	page_size = flash->page_size;
 
-	cmd[0] = CMD_PAGE_PROGRAM;
+	cmd[0] = flash->write_cmd;
 	for (actual = 0; actual < len; actual += chunk_len) {
 #ifdef CONFIG_SPI_FLASH_BAR
 		ret = spi_flash_bank(flash, offset);

drivers/mtd/spi/sf_probe.c

@@ -83,8 +83,8 @@ static const struct spi_flash_params spi_flash_params_table[] = {
 	{"S25FL032P",	   0x010215, 0x4d00,    64 * 1024,    64,	0,			  0},
 	{"S25FL064P",	   0x010216, 0x4d00,    64 * 1024,   128,	0,			  0},
 	{"S25FL128S_64K",  0x012018, 0x4d01,    64 * 1024,   256,	0,			  0},
-	{"S25FL256S_256K", 0x010219, 0x4d00,    64 * 1024,   512, RD_EXTN,		  0},
-	{"S25FL256S_64K",  0x010219, 0x4d01,	64 * 1024,   512, RD_EXTN,		  0},
+	{"S25FL256S_256K", 0x010219, 0x4d00,    64 * 1024,   512, RD_FULL,		     WR_QPP},
+	{"S25FL256S_64K",  0x010219, 0x4d01,	64 * 1024,   512, RD_FULL,		     WR_QPP},
 	{"S25FL512S_256K", 0x010220, 0x4d00,    64 * 1024,  1024,	0,			  0},
 	{"S25FL512S_64K",  0x010220, 0x4d01,    64 * 1024,  1024,	0,			  0},
 #endif
@@ -162,6 +162,7 @@ static u8 spi_read_cmds_array[] = {
 	CMD_READ_ARRAY_SLOW,
 	CMD_READ_DUAL_OUTPUT_FAST,
 	CMD_READ_DUAL_IO_FAST,
+	CMD_READ_QUAD_OUTPUT_FAST,
 };
 
 static struct spi_flash *spi_flash_validate_params(struct spi_slave *spi,
@@ -242,6 +243,13 @@ static struct spi_flash *spi_flash_validate_params(struct spi_slave *spi,
 		flash->read_cmd = CMD_READ_ARRAY_FAST;
 	}
 
+	/* Not require to look for fastest only two write cmds yet */
+	if (params->flags & WR_QPP && flash->spi->op_mode_tx & SPI_OPM_TX_QPP)
+		flash->write_cmd = CMD_QUAD_PAGE_PROGRAM;
+	else
+		/* Go for default supported write cmd */
+		flash->write_cmd = CMD_PAGE_PROGRAM;
+
 	/* Poll cmd seclection */
 	flash->poll_cmd = CMD_READ_STATUS;
 #ifdef CONFIG_SPI_FLASH_STMICRO

include/spi.h

@@ -31,11 +31,16 @@
 #define SPI_XFER_MMAP_END	0x10	/* Memory Mapped End */
 #define SPI_XFER_ONCE		(SPI_XFER_BEGIN | SPI_XFER_END)
 
+/* SPI TX operation modes */
+#define SPI_OPM_TX_QPP		1 << 0
+
 /* SPI RX operation modes */
 #define SPI_OPM_RX_AS		1 << 0
 #define SPI_OPM_RX_DOUT		1 << 1
 #define SPI_OPM_RX_DIO		1 << 2
-#define SPI_OPM_RX_EXTN		SPI_OPM_RX_AS | SPI_OPM_RX_DOUT | SPI_OPM_RX_DIO
+#define SPI_OPM_RX_QOF		1 << 3
+#define SPI_OPM_RX_EXTN		SPI_OPM_RX_AS | SPI_OPM_RX_DOUT | \
+				SPI_OPM_RX_DIO | SPI_OPM_RX_QOF
 
 /* Header byte that marks the start of the message */
 #define SPI_PREAMBLE_END_BYTE	0xec
@@ -50,6 +55,7 @@
  * @bus:		ID of the bus that the slave is attached to.
  * @cs:			ID of the chip select connected to the slave.
  * @op_mode_rx:		SPI RX operation mode.
+ * @op_mode_tx:		SPI TX operation mode.
  * @wordlen:		Size of SPI word in number of bits
  * @max_write_size:	If non-zero, the maximum number of bytes which can
  *			be written at once, excluding command bytes.
@@ -59,6 +65,7 @@ struct spi_slave {
 	unsigned int bus;
 	unsigned int cs;
 	u8 op_mode_rx;
+	u8 op_mode_tx;
 	unsigned int wordlen;
 	unsigned int max_write_size;
 	void *memory_map;

include/spi_flash.h

@@ -19,13 +19,18 @@
 #include <linux/types.h>
 #include <linux/compiler.h>
 
-/* Enum list - Extended read commands */
+/* No enum list for write commands only QPP */
+#define WR_QPP		1 << 4
+
+/* Enum list - Full read commands */
 enum spi_read_cmds {
 	ARRAY_SLOW = 1 << 0,
 	DUAL_OUTPUT_FAST = 1 << 1,
 	DUAL_IO_FAST = 1 << 2,
+	QUAD_OUTPUT_FAST = 1 << 3,
 };
 #define RD_EXTN		ARRAY_SLOW | DUAL_OUTPUT_FAST | DUAL_IO_FAST
+#define RD_FULL		RD_EXTN | QUAD_OUTPUT_FAST
 
 /**
  * struct spi_flash - SPI flash structure
@@ -41,7 +46,8 @@ enum spi_read_cmds {
  * @bank_curr:		Current flash bank
  * @poll_cmd:		Poll cmd - for flash erase/program
  * @erase_cmd:		Erase cmd 4K, 32K, 64K
- * @read_cmd:		Read cmd - Array Fast and Extn read
+ * @read_cmd:		Read cmd - Array Fast, Extn read and quad read.
+ * @write_cmd:		Write cmd - page and quad program.
  * @memory_map:		Address of read-only SPI flash access
  * @read:		Flash read ops: Read len bytes at offset into buf
  *			Supported cmds: Fast Array Read
@@ -67,6 +73,7 @@ struct spi_flash {
 	u8 poll_cmd;
 	u8 erase_cmd;
 	u8 read_cmd;
+	u8 write_cmd;
 
 	void *memory_map;
 	int (*read)(struct spi_flash *flash, u32 offset, size_t len, void *buf);