The LEDS_CMD command is only supported in some newer FW versions
(e.g. iwlwifi-8000C-31.ucode), so we can't send it to older versions
(such as iwlwifi-8000C-27.ucode).

To fix this, check for a new bit in the FW capabilities TLV that tells
when the command is supported.

Note that the current version of -31.ucode in linux-firmware.git
(31.532993.0) does not have this capability bit set, so the LED won't
work, even though this version should support it.  But we will update
this firmware soon, so it won't be a problem anymore.

Fixes: 7089ae63 ("iwlwifi: mvm: use firmware LED command where applicable")
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These devices support -34.ucode, so load it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Use bcast station for all non bufferable frames on AP and AD-HOC.

The host is no longer aware of STAs PS status because of buffer
station offload, so we can't rely on mac80211 to toggle on
IEEE80211_TX_CTL_NO_PS_BUFFER bit.

A possible issue with buffering such frames, beside the obvious spec
violation, is when a station disconnects while in PS but the AP isn't
aware of that. In such scenarios the AP won't be able to send probe
responses or auth frames so the STA won't be able to reconnect and
the AP will have a queue hang.

Fixes: 3e56eadf ("iwlwifi: mvm: implement AP/GO uAPSD support")
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There is a debug print that sometimes reaches over
110 chars, thus generating a warning in those cases.
Split the print into two to prevent these cases.

Fixes: 92b0f7b2 ("iwlwifi: split the regulatory rules when the bandwidth flags require it")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Work queues cannot be allocated when a mutex is held because the mutex
may be in use and that would make it sleep.  Doing so generates the
following splat with 4.13+:

[   19.513298] ======================================================
[   19.513429] WARNING: possible circular locking dependency detected
[   19.513557] 4.13.0-rc5+ #6 Not tainted
[   19.513638] ------------------------------------------------------
[   19.513767] cpuhp/0/12 is trying to acquire lock:
[   19.513867]  (&tz->lock){+.+.+.}, at: [<ffffffff924afebb>] thermal_zone_get_temp+0x5b/0xb0
[   19.514047]
[   19.514047] but task is already holding lock:
[   19.514166]  (cpuhp_state){+.+.+.}, at: [<ffffffff91cc4baa>] cpuhp_thread_fun+0x3a/0x210
[   19.514338]
[   19.514338] which lock already depends on the new lock.

This lock dependency already existed with previous kernel versions,
but it was not detected until commit 49dfe2a6 ("cpuhotplug: Link
lock stacks for hotplug callbacks") was introduced.
Reported-by: NDavid Weinehall <david.weinehall@intel.com>
Reported-by: NJiri Kosina <jikos@kernel.org>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make these const as they are only stored in the const field of a
net_device structure.
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: NRomain Perier <romain.perier@collabora.com>
Reviewed-by: NPeter Senna Tschudin <peter.senna@collabora.com>
Acked-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Unlike the other sections of the NVM, the hw section is in big-endian.
To read a value from it, we had to cast it to __be16.  Fix that by
using __be16 * for the entire section.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

At this point we have already copied the cfg pointer to mvm and we
have been dereferencing this pointer many times before, so it will
never be NULL or we would have crashed.  Remove the useless check.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We always call iwl_nvm_init() with read_nvm_from_nic == true, so this
argument is useless.  Remove it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We read the regulatory.lar_enabled field in iwl_fw_get_nvm() and store
it in nvm->lar_enabled, taking care of endianness.  But then later we
read it again to pass the value to iwl_init_sbands() without handling
endianness.  To solve this, simply reuse nvm->lar_enabled when calling
that function.

Fixes: e9e1ba3d ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The OTP in some SKUs have erroneously allowed 40MHz and 80MHz channels
in the 5.2GHz band.  The firmware has been modified to not allow this
in those SKUs, so the driver needs to do the same otherwise the
firmware will assert when we try to use it.

Cc: stable@vger.kernel.org
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Tx BA session should be started according to the current throughput
without any dependence on the internal rate scaling state. The criteria
for opening a BA session will be 10 frames per second.

Sending frequent del BAs can cause inter-op issues with some APs. We'll
not close a BA session until we receive an explicit del BA from the
peer.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There are some new flags in the channel flags that we don't know
about.  Also, the "WIDE" flag is very confusing, because it actually
means 20MHz bandwidth, which is not very wide.

Add the new flags and rename the confusing one.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We have a new PCI subsystem ID for 7265D.  Add it to the list.

Cc: stable@vger.kernel.org
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Newer versions of A000 devices come with two diffenent RF modules.
The PCI_ID, the subsystem ID and the RF ID are identical in these two cases,
so we need to differentiate them by using the CSR_HW_RF_ID register-
in order to load the appropriate firmware.
Signed-off-by: NTzipi Peres <tzipi.peres@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The code did not consider the case that the channel switch counter
is <= 1, which would result with an inaccurate calculation of the
time event apply time.

As the specification states that in case of counter == 0 the switch
occurs at any time after the reception the frame, and for counter == 1
the switch would happens before the next TBTT, schedule the time
event immediately.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

These messages are not reporting a real error, just the fact that the
firmware knows about more flags than the driver.

Currently these messages are presented to the user during boot if there
is no bootsplash covering the console, even when booting the kernel with
"quiet".

Demoting it to the warn level helps having a clean boot process.
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move the BT_MBOX_PRINT() macro from mvm/debugfs.c to fw/api/coex.h so
it can be reused and remove duplicate definition of BT_MBOX_MSG(),
keeping only the one already in coex.h.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we flush a queue, the packets will have a 'failed'
status but we shouldn't send a BAR. This check was missing.
Because of that, when we got an ampdu_action with
IEEE80211_AMPDU_TX_STOP_FLUSH, we started the following
ping pong with the firmware:

1) Set the station as 'draining'
2) Get a failed Tx status (DRAINED)
3) Send a BAR because of the failed Tx status

(loop of 2 and 3)

This loop wasn't endless since the BAR isn't sent on a
queue that would trigger a "nested" BAR.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If a time event is already scheduled when trying to schedule one for
channel switch, the code assumes the channel switch is already
scheduled and no further action is required.
However, it is possible that the scheduled time event is actually
for session protection (e.g. when the first beacon after association
contains the CSA IE). In this case the channel switch will not be
scheduled which will finally lead to disconnection.

Fix this by removing the old time event and schduling a new one for
the channel switch.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware team is now re-using a bit that hasn't been
used for a few generations. Re-use for TX_ON_AIR drop.
This bit will be set by the firmware to indicate that
a frame in an A-MPDU was dropped but not because of the
already mapped reasons.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We use mvmsta for the sta->drv_priv in mvm, but in rs.c we have a
bunch of instances using sta_priv, which is probably due to it being
copied from dvm.  Change all occurrences to mvmsta for consistency
with the rest of the driver
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We have some of the SAR dummy functions when ACPI is not set declared
in mvm.h and some declared in fw.c.  Group them all together in fw.c
for consistency and to avoid static/non-static issues.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we get a valid baid in a received frame, we need to
check that we are aware of this baid. If not, we check
that the OLD_SN bit set. If that's not the case, we issue
a WARNING. Print more data when that happens.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This name was missing in the list.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This allows to modify TFD_TX_CMD_SLOTS to a power of 2
which is smaller than 256.
Note that we still need to set values to wrap at 256
into the scheduler's write pointer, but all the rest of
the code can use shorter transmit queues.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware now adds more information about time sharing
with the Bluetooth core.
Adapt the API structures and add the new fields in the
debugfs hooks.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The iwl_wait_notification() function removes the wait entry from the
list.  To make it clearer that it's doing the same thing as
iwl_remove_notification(), call the latter instead of having duplicate
code.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no need to differentiate an INIT that ended early because of
RFKILL from one that succeded.  Additionally, if INIT fails later,
during calibration, due to RFKILL, we can just return success and
continue as if we were already in RFKILL to start with.

Remove this unnecessary differentiation and do some other small
clean-ups while at it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The corunning block was supposed to help in coex scenarios.
It required the driver to configure the firmware based on
the coupling between the two antennas of the devices.
This was never in use and the configuration sent by the
driver has always been blank.
Remove all that code.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware API defined in the header files didn't match
the structure that are actually passed by the firmware.
The impact could be a decision for MIMO in Tx or Rx in
coex scenarios.

Fixes: 430a3bba ("iwlwifi: mvm: BT Coex - new API")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we unmap a non-empty Tx queue, we need to free the
pages that we allocated for the headers in TSO flows.
This code existed for the 9000 device family, but somehow
it got left out when the new Tx path for the A000 devices
was written.

Fixes: 2b0c5946d9ed ("iwlwifi: pcie: introduce a000 TX queues management")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There are still some references to 3945 and 4965 HW, which were never
supported in iwlwifi.  These references were inherited from a previous
project and are irrelevant here.  Additionally, remove some irrelevant
references to 5100 HW.  Remove all these.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Although nmi was triggered fine till now, it appears
that the driver didn't write the exact correct values
to the correct addresses for each HW.
Fix the nmi triggering by setting the correct addresses
and values.

Fixes: 4c9706dc ("iwlwifi: update nmi register")
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The TVQM tells us the initial write pointer for a queue,
but that write pointer is in WiFi sequence number unit
and not in TFD index unit. Which means that the write
pointer in the TVQM's response can be bigger than the
Tx queue ring size.

Fix that by modulo'ing the write pointer from the TVQM
with the Tx queue size.

Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

One of the queue config params is the associated station id.
Hence the FW must know about the station prior to the queue allocation.
In a000 devices, allocating a queue without a valid station
results with assert 0x2B00.
In FW restart flow the queues are allocated before
adding the station so first add the station.
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fix this issue if it is not supported by the firmware.

Fixes: 00f481bd ("iwlwifi: mvm: add ctdp operations to debugfs")
Signed-off-by: NMatt Chen <matt.chen@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support a new version of the beacon template command. This replaces v8
of the command, which was missing the rate code.  Also, export rate
decision logic to a separate function.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When an RX block-ack session times out, the firmware, which offloads
RX reordering but not the BA session negotiation, stops the session
but doesn't send a DELBA.  This causes the the session to remain
active in the remote device, so no more BA sessions will be
established, causing a severe throughput degradation due to the lack
of aggregation.

Use the new ieee80211_rx_ba_timer_expired API when the ba session timer
expires, since this will tear down the ba session and also send a delba.

The previous API used is intended for drivers that offload the
addba/delba negotiation, but not the rx reordering, while our driver
does the opposite.

This patch depends on "mac80211: add api to start ba session timer
expired flow".
Signed-off-by: NNaftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>