iwlwifi: remove references to unsupported HW

There are still some references to 3945 and 4965 HW, which were never
supported in iwlwifi.  These references were inherited from a previous
project and are irrelevant here.  Additionally, remove some irrelevant
references to 5100 HW.  Remove all these.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

drivers/net/wireless/intel/iwlwifi/dvm/commands.h

@@ -311,11 +311,6 @@ enum {
 
 /**
  * rate_n_flags Tx antenna masks
- * 4965 has 2 transmitters
- * 5100 has 1 transmitter B
- * 5150 has 1 transmitter A
- * 5300 has 3 transmitters
- * 5350 has 3 transmitters
  * bit14:16
  */
 #define RATE_MCS_ANT_POS	14
@@ -1230,7 +1225,6 @@ struct iwl_rx_mpdu_res_start {
  */
 
 /*
- * 4965 uCode updates these Tx attempt count values in host DRAM.
  * Used for managing Tx retries when expecting block-acks.
  * Driver should set these fields to 0.
  */
@@ -1540,7 +1534,7 @@ struct iwl_link_qual_general_params {
 	/* Best single antenna to use for single stream (legacy, SISO). */
 	u8 single_stream_ant_msk;	/* LINK_QUAL_ANT_* */
 
-	/* Best antennas to use for MIMO (unused for 4965, assumes both). */
+	/* Best antennas to use for MIMO */
 	u8 dual_stream_ant_msk;		/* LINK_QUAL_ANT_* */
 
 	/*

drivers/net/wireless/intel/iwlwifi/iwl-csr.h

@@ -169,7 +169,7 @@
 
 /*
  * CSR Hardware Revision Workaround Register.  Indicates hardware rev;
- * "step" determines CCK backoff for txpower calculation.  Used for 4965 only.
+ * "step" determines CCK backoff for txpower calculation.
  * See also CSR_HW_REV register.
  * Bit fields:
  *  3-2:  0 = A, 1 = B, 2 = C, 3 = D step

drivers/net/wireless/intel/iwlwifi/pcie/trans.c

@@ -1842,8 +1842,8 @@ static bool iwl_trans_pcie_grab_nic_access(struct iwl_trans *trans,
 	 * These bits say the device is running, and should keep running for
 	 * at least a short while (at least as long as MAC_ACCESS_REQ stays 1),
 	 * but they do not indicate that embedded SRAM is restored yet;
-	 * 3945 and 4965 have volatile SRAM, and must save/restore contents
-	 * to/from host DRAM when sleeping/waking for power-saving.
+	 * HW with volatile SRAM must save/restore contents to/from
+	 * host DRAM when sleeping/waking for power-saving.
 	 * Each direction takes approximately 1/4 millisecond; with this
 	 * overhead, it's a good idea to grab and hold MAC_ACCESS_REQUEST if a
 	 * series of register accesses are expected (e.g. reading Event Log),
@@ -1851,8 +1851,9 @@ static bool iwl_trans_pcie_grab_nic_access(struct iwl_trans *trans,
 	 *
 	 * CSR_UCODE_DRV_GP1 register bit MAC_SLEEP == 0 indicates that
 	 * SRAM is okay/restored.  We don't check that here because this call
-	 * is just for hardware register access; but GP1 MAC_SLEEP check is a
-	 * good idea before accessing 3945/4965 SRAM (e.g. reading Event Log).
+	 * is just for hardware register access; but GP1 MAC_SLEEP
+	 * check is a good idea before accessing the SRAM of HW with
+	 * volatile SRAM (e.g. reading Event Log).
 	 *
 	 * 5000 series and later (including 1000 series) have non-volatile SRAM,
 	 * and do not save/restore SRAM when power cycling.