usb: usb251xb: remove max_{power,current}_{sp,bp} properties

Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: NRichard Leitner <richard.leitner@skidata.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/devicetree/bindings/usb/usb251xb.txt

@@ -40,26 +40,6 @@ Optional properties :
 	device connected.
  - sp-disabled-ports : Specifies the ports which will be self-power disabled
  - bp-disabled-ports : Specifies the ports which will be bus-power disabled
- - max-sp-power : Specifies the maximum current the hub consumes from an
-	upstream port when operating as self-powered hub including the power
-	consumption of a permanently attached peripheral if the hub is
-	configured as a compound device. The value is given in mA in a 0 - 500
-	range (default is 2).
- - max-bp-power : Specifies the maximum current the hub consumes from an
-	upstream port when operating as bus-powered hub including the power
-	consumption of a permanently attached peripheral if the hub is
-	configured as a compound device. The value is given in mA in a 0 - 500
-	range (default is 100).
- - max-sp-current : Specifies the maximum current the hub consumes from an
-	upstream port when operating as self-powered hub EXCLUDING the power
-	consumption of a permanently attached peripheral if the hub is
-	configured as a compound device. The value is given in mA in a 0 - 500
-	range (default is 2).
- - max-bp-current : Specifies the maximum current the hub consumes from an
-	upstream port when operating as bus-powered hub EXCLUDING the power
-	consumption of a permanently attached peripheral if the hub is
-	configured as a compound device. The value is given in mA in a 0 - 500
-	range (default is 100).
  - power-on-time : Specifies the time it takes from the time the host initiates
 	the power-on sequence to a port until the port has adequate power. The
 	value is given in ms in a 0 - 510 range (default is 100ms).

drivers/usb/misc/usb251xb.c

@@ -432,26 +432,6 @@ static int usb251xb_get_ofdata(struct usb251xb *hub,
 		}
 	}
 
-	hub->max_power_sp = USB251XB_DEF_MAX_POWER_SELF;
-	if (!of_property_read_u32(np, "max-sp-power", property_u32))
-		hub->max_power_sp = min_t(u8, be32_to_cpu(*property_u32) / 2,
-					  250);
-
-	hub->max_power_bp = USB251XB_DEF_MAX_POWER_BUS;
-	if (!of_property_read_u32(np, "max-bp-power", property_u32))
-		hub->max_power_bp = min_t(u8, be32_to_cpu(*property_u32) / 2,
-					  250);
-
-	hub->max_current_sp = USB251XB_DEF_MAX_CURRENT_SELF;
-	if (!of_property_read_u32(np, "max-sp-current", property_u32))
-		hub->max_current_sp = min_t(u8, be32_to_cpu(*property_u32) / 2,
-					    250);
-
-	hub->max_current_bp = USB251XB_DEF_MAX_CURRENT_BUS;
-	if (!of_property_read_u32(np, "max-bp-current", property_u32))
-		hub->max_current_bp = min_t(u8, be32_to_cpu(*property_u32) / 2,
-					    250);
-
 	hub->power_on_time = USB251XB_DEF_POWER_ON_TIME;
 	if (!of_property_read_u32(np, "power-on-time", property_u32))
 		hub->power_on_time = min_t(u8, be32_to_cpu(*property_u32) / 2,
@@ -492,6 +472,10 @@ static int usb251xb_get_ofdata(struct usb251xb *hub,
 	/* The following parameters are currently not exposed to devicetree, but
 	 * may be as soon as needed.
 	 */
+	hub->max_power_sp = USB251XB_DEF_MAX_POWER_SELF;
+	hub->max_power_bp = USB251XB_DEF_MAX_POWER_BUS;
+	hub->max_current_sp = USB251XB_DEF_MAX_CURRENT_SELF;
+	hub->max_current_bp = USB251XB_DEF_MAX_CURRENT_BUS;
 	hub->bat_charge_en = USB251XB_DEF_BATTERY_CHARGING_ENABLE;
 	hub->boost_up = USB251XB_DEF_BOOST_UP;
 	hub->boost_x = USB251XB_DEF_BOOST_X;