serial: remove cris/etrax uart drivers

The cris architecture is getting removed, so we don't need the
uart driver any more.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt

-ETRAX FS UART
-
-Required properties:
-- compatible : "axis,etraxfs-uart"
-- reg: offset and length of the register set for the device.
-- interrupts: device interrupt
-
-Optional properties:
-- {dtr,dsr,rng,dcd}-gpios: specify a GPIO for DTR/DSR/RI/DCD
-  line respectively.
-
-Example:
-
-serial@b00260000 {
-	compatible = "axis,etraxfs-uart";
-	reg = <0xb0026000 0x1000>;
-	interrupts = <68>;
-	dtr-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>;
-	dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>;
-	rng-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>;
-	dcd-gpios = <&sysgpio 3 GPIO_ACTIVE_LOW>;
-};

drivers/tty/serial/Kconfig

@@ -1114,17 +1114,6 @@ config SERIAL_VT8500_CONSOLE
 	depends on SERIAL_VT8500=y
 	select SERIAL_CORE_CONSOLE
 
-config SERIAL_ETRAXFS
-	bool "ETRAX FS serial port support"
-	depends on ETRAX_ARCH_V32 && OF
-	select SERIAL_CORE
-	select SERIAL_MCTRL_GPIO if GPIOLIB
-
-config SERIAL_ETRAXFS_CONSOLE
-	bool "ETRAX FS serial console support"
-	depends on SERIAL_ETRAXFS
-	select SERIAL_CORE_CONSOLE
-
 config SERIAL_NETX
 	tristate "NetX serial port support"
 	depends on ARCH_NETX

drivers/tty/serial/Makefile

@@ -51,8 +51,6 @@ obj-$(CONFIG_SERIAL_M32R_SIO) += m32r_sio.o
 obj-$(CONFIG_SERIAL_MPSC) += mpsc.o
 obj-$(CONFIG_SERIAL_MESON) += meson_uart.o
 obj-$(CONFIG_SERIAL_SB1250_DUART) += sb1250-duart.o
-obj-$(CONFIG_ETRAX_SERIAL) += crisv10.o
-obj-$(CONFIG_SERIAL_ETRAXFS) += etraxfs-uart.o
 obj-$(CONFIG_SERIAL_SCCNXP) += sccnxp.o
 obj-$(CONFIG_SERIAL_SC16IS7XX_CORE) += sc16is7xx.o
 obj-$(CONFIG_SERIAL_JSM) += jsm/

drivers/tty/serial/crisv10.h

-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * serial.h: Arch-dep definitions for the Etrax100 serial driver.
- *
- * Copyright (C) 1998-2007 Axis Communications AB
- */
-
-#ifndef _ETRAX_SERIAL_H
-#define _ETRAX_SERIAL_H
-
-#include <linux/circ_buf.h>
-#include <asm/termios.h>
-#include <asm/dma.h>
-#include <arch/io_interface_mux.h>
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-#define SERIAL_RECV_DESCRIPTORS 8
-
-struct etrax_recv_buffer {
-	struct etrax_recv_buffer *next;
-	unsigned short length;
-	unsigned char error;
-	unsigned char pad;
-
-	unsigned char buffer[0];
-};
-
-struct e100_serial {
-	struct tty_port port;
-	int baud;
-	volatile u8	*ioport;	/* R_SERIALx_CTRL */
-	u32		irq;	/* bitnr in R_IRQ_MASK2 for dmaX_descr */
-
-	/* Output registers */
-	volatile u8 *oclrintradr;	/* adr to R_DMA_CHx_CLR_INTR */
-	volatile u32 *ofirstadr;	/* adr to R_DMA_CHx_FIRST */
-	volatile u8 *ocmdadr;		/* adr to R_DMA_CHx_CMD */
-	const volatile u8 *ostatusadr;	/* adr to R_DMA_CHx_STATUS */
-
-	/* Input registers */
-	volatile u8 *iclrintradr;	/* adr to R_DMA_CHx_CLR_INTR */
-	volatile u32 *ifirstadr;	/* adr to R_DMA_CHx_FIRST */
-	volatile u8 *icmdadr;		/* adr to R_DMA_CHx_CMD */
-	volatile u32 *idescradr;	/* adr to R_DMA_CHx_DESCR */
-
-	u8 rx_ctrl;	/* shadow for R_SERIALx_REC_CTRL */
-	u8 tx_ctrl;	/* shadow for R_SERIALx_TR_CTRL */
-	u8 iseteop;	/* bit number for R_SET_EOP for the input dma */
-	int enabled;	/* Set to 1 if the port is enabled in HW config */
-
-	u8 dma_out_enabled;	/* Set to 1 if DMA should be used */
-	u8 dma_in_enabled;	/* Set to 1 if DMA should be used */
-
-	/* end of fields defined in rs_table[] in .c-file */
-	int		dma_owner;
-	unsigned int	dma_in_nbr;
-	unsigned int	dma_out_nbr;
-	unsigned int	dma_in_irq_nbr;
-	unsigned int	dma_out_irq_nbr;
-	unsigned long	dma_in_irq_flags;
-	unsigned long	dma_out_irq_flags;
-	char		*dma_in_irq_description;
-	char		*dma_out_irq_description;
-
-	enum cris_io_interface io_if;
-	char            *io_if_description;
-
-	u8		uses_dma_in;  /* Set to 1 if DMA is used */
-	u8		uses_dma_out; /* Set to 1 if DMA is used */
-	u8		forced_eop;   /* a fifo eop has been forced */
-	int			baud_base;     /* For special baudrates */
-	int			custom_divisor; /* For special baudrates */
-	struct etrax_dma_descr	tr_descr;
-	struct etrax_dma_descr	rec_descr[SERIAL_RECV_DESCRIPTORS];
-	int			cur_rec_descr;
-
-	volatile int		tr_running; /* 1 if output is running */
-
-	int			x_char;	/* xon/xoff character */
-	unsigned long		event;
-	int			line;
-	int			type;  /* PORT_ETRAX */
-	struct circ_buf		xmit;
-	struct etrax_recv_buffer *first_recv_buffer;
-	struct etrax_recv_buffer *last_recv_buffer;
-	unsigned int		recv_cnt;
-	unsigned int		max_recv_cnt;
-
-	struct work_struct	work;
-	struct async_icount	icount;   /* error-statistics etc.*/
-
-	unsigned long char_time_usec;       /* The time for 1 char, in usecs */
-	unsigned long flush_time_usec;      /* How often we should flush */
-	unsigned long last_tx_active_usec;  /* Last tx usec in the jiffies */
-	unsigned long last_tx_active;       /* Last tx time in jiffies */
-	unsigned long last_rx_active_usec;  /* Last rx usec in the jiffies */
-	unsigned long last_rx_active;       /* Last rx time in jiffies */
-
-	int break_detected_cnt;
-	int errorcode;
-
-#ifdef CONFIG_ETRAX_RS485
-	struct serial_rs485	rs485;  /* RS-485 support */
-#endif
-};
-
-/* this PORT is not in the standard serial.h. it's not actually used for
- * anything since we only have one type of async serial-port anyway in this
- * system.
- */
-
-#define PORT_ETRAX 1
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP	0
-
-#endif /* __KERNEL__ */
-
-#endif /* !_ETRAX_SERIAL_H */