diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
index 6b789f2ee879748c79c67220f6b13df0ae4c1dcf..afcfbc34e24340ab006c0cba6c6de7591888aee6 100644
--- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
@@ -8,7 +8,8 @@ Required properties:
 Optional properties:
 - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
                   in DCE mode by default.
-- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
+- rs485-rts-delay, rs485-rts-active-low, rs485-rx-during-tx,
+  linux,rs485-enabled-at-boot-time: see rs485.txt
 
 Please check Documentation/devicetree/bindings/serial/serial.txt
 for the complete list of generic properties.
diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
index 59567b51cf098bfa963fee4283b63e01d226bb31..6bd3f2e93d61d9818bda71c6c328c407b082a884 100644
--- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
@@ -16,7 +16,8 @@ Required properties:
 Optional properties:
 - dmas: A list of two dma specifiers, one for each entry in dma-names.
 - dma-names: should contain "tx" and "rx".
-- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
+- rs485-rts-delay, rs485-rts-active-low, rs485-rx-during-tx,
+  linux,rs485-enabled-at-boot-time: see rs485.txt
 
 Note: Optional properties for DMA support. Write them both or both not.
 
diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt
index 43eac675f21f5fd58cda23535facab5b82903957..4b0f05adb22811a99850e36d66be1073259b03c1 100644
--- a/Documentation/devicetree/bindings/serial/omap_serial.txt
+++ b/Documentation/devicetree/bindings/serial/omap_serial.txt
@@ -20,6 +20,7 @@ Optional properties:
          node and a DMA channel number.
 - dma-names : "rx" for receive channel, "tx" for transmit channel.
 - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
+- rs485-rts-active-high: drive RTS high when sending (default is low).
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt
index b8415936dfdbc59cdf8c6027337603579d3e9403..b7c29f74ebb2e0a3bf9cea65e4dc559ed7e3bb5d 100644
--- a/Documentation/devicetree/bindings/serial/rs485.txt
+++ b/Documentation/devicetree/bindings/serial/rs485.txt
@@ -12,6 +12,7 @@ Optional properties:
   * b is the delay between end of data sent and rts signal in milliseconds
       it corresponds to the delay after sending data and actual release of the line.
   If this property is not specified, <0 0> is assumed.
+- rs485-rts-active-low: drive RTS low when sending (default is high).
 - linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485
   feature at boot time. It can be disabled later with proper ioctl.
 - rs485-rx-during-tx: empty property that enables the receiving of data even