Merge remote-tracking branches 'spi/topic/lm70llp', 'spi/topic/loopback',...

Merge remote-tracking branches 'spi/topic/lm70llp', 'spi/topic/loopback', 'spi/topic/mtk' and 'spi/topic/omap2-mcspi' into spi-next

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

@@ -2,9 +2,10 @@ Binding for MTK SPI controller
 
 Required properties:
 - compatible: should be one of the following.
-    - mediatek,mt8173-spi: for mt8173 platforms
-    - mediatek,mt8135-spi: for mt8135 platforms
+    - mediatek,mt2701-spi: for mt2701 platforms
     - mediatek,mt6589-spi: for mt6589 platforms
+    - mediatek,mt8135-spi: for mt8135 platforms
+    - mediatek,mt8173-spi: for mt8173 platforms
 
 - #address-cells: should be 1.
 
@@ -29,10 +30,10 @@ Required properties:
   muxes clock, and "spi-clk" for the clock gate.
 
 Optional properties:
--cs-gpios: see spi-bus.txt, only required for MT8173.
+-cs-gpios: see spi-bus.txt.
 
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
-  controller used. This is a array, the element value should be 0~3,
+  controller used. This is an array, the element value should be 0~3,
   only required for MT8173.
     0: specify GPIO69,70,71,72 for spi pins.
     1: specify GPIO102,103,104,105 for spi pins.

drivers/spi/Kconfig

@@ -689,6 +689,15 @@ config SPI_SPIDEV
 	  Note that this application programming interface is EXPERIMENTAL
 	  and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 
+config SPI_LOOPBACK_TEST
+	tristate "spi loopback test framework support"
+	depends on m
+	help
+	  This enables the SPI loopback testing framework driver
+
+	  primarily used for development of spi_master drivers
+	  and to detect regressions
+
 config SPI_TLE62X0
 	tristate "Infineon TLE62X0 (for power switching)"
 	depends on SYSFS

drivers/spi/Makefile

@@ -8,6 +8,7 @@ ccflags-$(CONFIG_SPI_DEBUG) := -DDEBUG
 # config declarations into driver model code
 obj-$(CONFIG_SPI_MASTER)		+= spi.o
 obj-$(CONFIG_SPI_SPIDEV)		+= spidev.o
+obj-$(CONFIG_SPI_LOOPBACK_TEST)		+= spi-loopback-test.o
 
 # SPI master controller drivers (bus)
 obj-$(CONFIG_SPI_ALTERA)		+= spi-altera.o

drivers/spi/spi-lm70llp.c

@@ -14,6 +14,8 @@
  * GNU General Public License for more details.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
@@ -23,11 +25,9 @@
 #include <linux/sysfs.h>
 #include <linux/workqueue.h>
 
-
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_bitbang.h>
 
-
 /*
  * The LM70 communicates with a host processor using a 3-wire variant of
  * the SPI/Microwire bus interface. This driver specifically supports an
@@ -88,7 +88,6 @@ struct spi_lm70llp {
 /* REVISIT : ugly global ; provides "exclusive open" facility */
 static struct spi_lm70llp *lm70llp;
 
-
 /*-------------------------------------------------------------------*/
 
 static inline struct spi_lm70llp *spidev_to_pp(struct spi_device *spi)
@@ -122,12 +121,14 @@ static inline void assertCS(struct spi_lm70llp *pp)
 static inline void clkHigh(struct spi_lm70llp *pp)
 {
 	u8 data = parport_read_data(pp->port);
+
 	parport_write_data(pp->port, data | SCLK);
 }
 
 static inline void clkLow(struct spi_lm70llp *pp)
 {
 	u8 data = parport_read_data(pp->port);
+
 	parport_write_data(pp->port, data & ~SCLK);
 }
 
@@ -166,8 +167,10 @@ static inline void setmosi(struct spi_device *s, int is_on)
 static inline int getmiso(struct spi_device *s)
 {
 	struct spi_lm70llp *pp = spidev_to_pp(s);
-	return ((SIO == (parport_read_status(pp->port) & SIO)) ? 0 : 1 );
+
+	return ((SIO == (parport_read_status(pp->port) & SIO)) ? 0 : 1);
 }
+
 /*--------------------------------------------------------------------*/
 
 #include "spi-bitbang-txrx.h"
@@ -196,11 +199,10 @@ static void spi_lm70llp_attach(struct parport *p)
 	struct spi_lm70llp	*pp;
 	struct spi_master	*master;
 	int			status;
+	struct pardev_cb	lm70llp_cb;
 
 	if (lm70llp) {
-		printk(KERN_WARNING
-			"%s: spi_lm70llp instance already loaded. Aborting.\n",
-			DRVNAME);
+		pr_warn("spi_lm70llp instance already loaded. Aborting.\n");
 		return;
 	}
 
@@ -227,9 +229,11 @@ static void spi_lm70llp_attach(struct parport *p)
 	 * Parport hookup
 	 */
 	pp->port = p;
-	pd = parport_register_device(p, DRVNAME,
-			NULL, NULL, NULL,
-			PARPORT_FLAG_EXCL, pp);
+	memset(&lm70llp_cb, 0, sizeof(lm70llp_cb));
+	lm70llp_cb.private = pp;
+	lm70llp_cb.flags = PARPORT_FLAG_EXCL;
+	pd = parport_register_dev_model(p, DRVNAME, &lm70llp_cb, 0);
+
 	if (!pd) {
 		status = -ENOMEM;
 		goto out_free_master;
@@ -245,9 +249,8 @@ static void spi_lm70llp_attach(struct parport *p)
 	 */
 	status = spi_bitbang_start(&pp->bitbang);
 	if (status < 0) {
-		printk(KERN_WARNING
-			"%s: spi_bitbang_start failed with status %d\n",
-			DRVNAME, status);
+		dev_warn(&pd->dev, "spi_bitbang_start failed with status %d\n",
+			 status);
 		goto out_off_and_release;
 	}
 
@@ -274,7 +277,7 @@ static void spi_lm70llp_attach(struct parport *p)
 		dev_dbg(&pp->spidev_lm70->dev, "spidev_lm70 at %s\n",
 			dev_name(&pp->spidev_lm70->dev));
 	else {
-		printk(KERN_WARNING "%s: spi_new_device failed\n", DRVNAME);
+		dev_warn(&pd->dev, "spi_new_device failed\n");
 		status = -ENODEV;
 		goto out_bitbang_stop;
 	}
@@ -293,9 +296,9 @@ static void spi_lm70llp_attach(struct parport *p)
 out_parport_unreg:
 	parport_unregister_device(pd);
 out_free_master:
-	(void) spi_master_put(master);
+	spi_master_put(master);
 out_fail:
-	pr_info("%s: spi_lm70llp probe fail, status %d\n", DRVNAME, status);
+	pr_info("spi_lm70llp probe fail, status %d\n", status);
 }
 
 static void spi_lm70llp_detach(struct parport *p)
@@ -314,16 +317,16 @@ static void spi_lm70llp_detach(struct parport *p)
 	parport_release(pp->pd);
 	parport_unregister_device(pp->pd);
 
-	(void) spi_master_put(pp->bitbang.master);
+	spi_master_put(pp->bitbang.master);
 
 	lm70llp = NULL;
 }
 
-
 static struct parport_driver spi_lm70llp_drv = {
 	.name =		DRVNAME,
-	.attach =	spi_lm70llp_attach,
+	.match_port =	spi_lm70llp_attach,
 	.detach =	spi_lm70llp_detach,
+	.devmodel =	true,
 };
 
 static int __init init_spi_lm70llp(void)

drivers/spi/spi-mt65xx.c

@@ -95,8 +95,7 @@ struct mtk_spi {
 	const struct mtk_spi_compatible *dev_comp;
 };
 
-static const struct mtk_spi_compatible mt6589_compat;
-static const struct mtk_spi_compatible mt8135_compat;
+static const struct mtk_spi_compatible mtk_common_compat;
 static const struct mtk_spi_compatible mt8173_compat = {
 	.need_pad_sel = true,
 	.must_tx = true,
@@ -112,9 +111,18 @@ static const struct mtk_chip_config mtk_default_chip_info = {
 };
 
 static const struct of_device_id mtk_spi_of_match[] = {
-	{ .compatible = "mediatek,mt6589-spi", .data = (void *)&mt6589_compat },
-	{ .compatible = "mediatek,mt8135-spi", .data = (void *)&mt8135_compat },
-	{ .compatible = "mediatek,mt8173-spi", .data = (void *)&mt8173_compat },
+	{ .compatible = "mediatek,mt2701-spi",
+		.data = (void *)&mtk_common_compat,
+	},
+	{ .compatible = "mediatek,mt6589-spi",
+		.data = (void *)&mtk_common_compat,
+	},
+	{ .compatible = "mediatek,mt8135-spi",
+		.data = (void *)&mtk_common_compat,
+	},
+	{ .compatible = "mediatek,mt8173-spi",
+		.data = (void *)&mt8173_compat,
+	},
 	{}
 };
 MODULE_DEVICE_TABLE(of, mtk_spi_of_match);
@@ -154,9 +162,6 @@ static int mtk_spi_prepare_message(struct spi_master *master,
 		reg_val |= SPI_CMD_CPOL;
 	else
 		reg_val &= ~SPI_CMD_CPOL;
-	writel(reg_val, mdata->base + SPI_CMD_REG);
-
-	reg_val = readl(mdata->base + SPI_CMD_REG);
 
 	/* set the mlsbx and mlsbtx */
 	if (chip_config->tx_mlsb)
@@ -618,7 +623,8 @@ static int mtk_spi_probe(struct platform_device *pdev)
 	ret = clk_set_parent(mdata->sel_clk, mdata->parent_clk);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "failed to clk_set_parent (%d)\n", ret);
-		goto err_disable_clk;
+		clk_disable_unprepare(mdata->spi_clk);
+		goto err_put_master;
 	}
 
 	clk_disable_unprepare(mdata->spi_clk);
@@ -628,7 +634,7 @@ static int mtk_spi_probe(struct platform_device *pdev)
 	ret = devm_spi_register_master(&pdev->dev, master);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register master (%d)\n", ret);
-		goto err_put_master;
+		goto err_disable_runtime_pm;
 	}
 
 	if (mdata->dev_comp->need_pad_sel) {
@@ -637,14 +643,14 @@ static int mtk_spi_probe(struct platform_device *pdev)
 				"pad_num does not match num_chipselect(%d != %d)\n",
 				mdata->pad_num, master->num_chipselect);
 			ret = -EINVAL;
-			goto err_put_master;
+			goto err_disable_runtime_pm;
 		}
 
 		if (!master->cs_gpios && master->num_chipselect > 1) {
 			dev_err(&pdev->dev,
 				"cs_gpios not specified and num_chipselect > 1\n");
 			ret = -EINVAL;
-			goto err_put_master;
+			goto err_disable_runtime_pm;
 		}
 
 		if (master->cs_gpios) {
@@ -655,7 +661,7 @@ static int mtk_spi_probe(struct platform_device *pdev)
 				if (ret) {
 					dev_err(&pdev->dev,
 						"can't get CS GPIO %i\n", i);
-					goto err_put_master;
+					goto err_disable_runtime_pm;
 				}
 			}
 		}
@@ -663,8 +669,8 @@ static int mtk_spi_probe(struct platform_device *pdev)
 
 	return 0;
 
-err_disable_clk:
-	clk_disable_unprepare(mdata->spi_clk);
+err_disable_runtime_pm:
+	pm_runtime_disable(&pdev->dev);
 err_put_master:
 	spi_master_put(master);
 

drivers/spi/spi-omap2-mcspi.c

@@ -24,6 +24,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
 #include <linux/omap-dma.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/err.h>
 #include <linux/clk.h>
@@ -1024,13 +1025,6 @@ static int omap2_mcspi_setup(struct spi_device *spi)
 		spi->controller_state = cs;
 		/* Link this to context save list */
 		list_add_tail(&cs->node, &ctx->cs);
-	}
-
-	if (!mcspi_dma->dma_rx || !mcspi_dma->dma_tx) {
-		ret = omap2_mcspi_request_dma(spi);
-		if (ret < 0 && ret != -EAGAIN)
-			return ret;
-	}
 
 		if (gpio_is_valid(spi->cs_gpio)) {
 			ret = gpio_request(spi->cs_gpio, dev_name(&spi->dev));
@@ -1038,7 +1032,15 @@ static int omap2_mcspi_setup(struct spi_device *spi)
 				dev_err(&spi->dev, "failed to request gpio\n");
 				return ret;
 			}
-		gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
+			gpio_direction_output(spi->cs_gpio,
+					 !(spi->mode & SPI_CS_HIGH));
+		}
+	}
+
+	if (!mcspi_dma->dma_rx || !mcspi_dma->dma_tx) {
+		ret = omap2_mcspi_request_dma(spi);
+		if (ret < 0 && ret != -EAGAIN)
+			return ret;
 	}
 
 	ret = pm_runtime_get_sync(mcspi->dev);
@@ -1536,14 +1538,23 @@ static int omap2_mcspi_resume(struct device *dev)
 	}
 	pm_runtime_mark_last_busy(mcspi->dev);
 	pm_runtime_put_autosuspend(mcspi->dev);
-	return 0;
+
+	return pinctrl_pm_select_default_state(dev);
 }
+
+static int omap2_mcspi_suspend(struct device *dev)
+{
+	return pinctrl_pm_select_sleep_state(dev);
+}
+
 #else
+#define omap2_mcspi_suspend	NULL
 #define	omap2_mcspi_resume	NULL
 #endif
 
 static const struct dev_pm_ops omap2_mcspi_pm_ops = {
 	.resume = omap2_mcspi_resume,
+	.suspend = omap2_mcspi_suspend,
 	.runtime_resume	= omap_mcspi_runtime_resume,
 };
 

drivers/spi/spi-test.h

+/*
+ *  linux/drivers/spi/spi-test.h
+ *
+ *  (c) Martin Sperl <kernel@martin.sperl.org>
+ *
+ *  spi_test definitions
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ */
+
+#include <linux/spi/spi.h>
+
+#define SPI_TEST_MAX_TRANSFERS 4
+#define SPI_TEST_MAX_SIZE (32 * PAGE_SIZE)
+#define SPI_TEST_MAX_ITERATE 32
+
+/* the "dummy" start addresses used in spi_test
+ * these addresses get translated at a later stage
+ */
+#define RX_START	BIT(30)
+#define TX_START	BIT(31)
+#define RX(off)		((void *)(RX_START + off))
+#define TX(off)		((void *)(TX_START + off))
+
+/* some special defines for offsets */
+#define SPI_TEST_MAX_SIZE_HALF	BIT(29)
+
+/* detection pattern for unfinished reads...
+ * - 0x00 or 0xff could be valid levels for tx_buf = NULL,
+ * so we do not use either of them
+ */
+#define SPI_TEST_PATTERN_UNWRITTEN 0xAA
+#define SPI_TEST_PATTERN_DO_NOT_WRITE 0x55
+#define SPI_TEST_CHECK_DO_NOT_WRITE 64
+
+/**
+ * struct spi_test - describes a specific (set of) tests to execute
+ *
+ * @description:      description of the test
+ *
+ * @msg:              a template @spi_message usedfor the default settings
+ * @transfers:        array of @spi_transfers that are part of the
+ *                    resulting spi_message. The first transfer with len == 0
+ *                    signifies the end of the list
+ * @transfer_count:   normally computed number of transfers with len > 0
+ *
+ * @run_test:         run a specific spi_test - this allows to override
+ *                    the default implementation of @spi_test_run_transfer
+ *                    either to add some custom filters for a specific test
+ *                    or to effectively run some very custom tests...
+ * @execute_msg:      run the spi_message for real - this allows to override
+ *                    @spi_test_execute_msg to apply final modifications
+ *                    on the spi_message
+ * @expected_return:  the expected return code - in some cases we want to
+ *                    test also for error conditions
+ *
+ * @iterate_len:      list of length to iterate on (in addition to the
+ *                    explicitly set @spi_transfer.len)
+ * @iterate_tx_align: change the alignment of @spi_transfer.tx_buf
+ *                    for all values in the below range if set.
+ *                    the ranges are:
+ *                    [0 : @spi_master.dma_alignment[ if set
+ *                    [0 : iterate_tx_align[ if unset
+ * @iterate_rx_align: change the alignment of @spi_transfer.rx_buf
+ *                    see @iterate_tx_align for details
+ * @iterate_transfer_mask: the bitmask of transfers to which the iterations
+ *                         apply - if 0, then it applies to all transfer
+ *
+ * @fill_option:      define the way how tx_buf is filled
+ * @fill_pattern:     fill pattern to apply to the tx_buf
+ *                    (used in some of the @fill_options)
+ */
+
+struct spi_test {
+	char description[64];
+	struct spi_message msg;
+	struct spi_transfer transfers[SPI_TEST_MAX_TRANSFERS];
+	unsigned int transfer_count;
+	int (*run_test)(struct spi_device *spi, struct spi_test *test,
+			void *tx, void *rx);
+	int (*execute_msg)(struct spi_device *spi, struct spi_test *test,
+			   void *tx, void *rx);
+	int expected_return;
+	/* iterate over all the non-zero values */
+	int iterate_len[SPI_TEST_MAX_ITERATE];
+	int iterate_tx_align;
+	int iterate_rx_align;
+	u32 iterate_transfer_mask;
+	/* the tx-fill operation */
+	u32 fill_option;
+#define FILL_MEMSET_8	0	/* just memset with 8 bit */
+#define FILL_MEMSET_16	1	/* just memset with 16 bit */
+#define FILL_MEMSET_24	2	/* just memset with 24 bit */
+#define FILL_MEMSET_32	3	/* just memset with 32 bit */
+#define FILL_COUNT_8	4	/* fill with a 8 byte counter */
+#define FILL_COUNT_16	5	/* fill with a 16 bit counter */
+#define FILL_COUNT_24	6	/* fill with a 24 bit counter */
+#define FILL_COUNT_32	7	/* fill with a 32 bit counter */
+#define FILL_TRANSFER_BYTE_8  8	/* fill with the transfer byte - 8 bit */
+#define FILL_TRANSFER_BYTE_16 9	/* fill with the transfer byte - 16 bit */
+#define FILL_TRANSFER_BYTE_24 10 /* fill with the transfer byte - 24 bit */
+#define FILL_TRANSFER_BYTE_32 11 /* fill with the transfer byte - 32 bit */
+#define FILL_TRANSFER_NUM     16 /* fill with the transfer number */
+	u32 fill_pattern;
+};
+
+/* default implementation for @spi_test.run_test */
+int spi_test_run_test(struct spi_device *spi,
+		      const struct spi_test *test,
+		      void *tx, void *rx);
+
+/* default implementation for @spi_test.execute_msg */
+int spi_test_execute_msg(struct spi_device *spi,
+			 struct spi_test *test,
+			 void *tx, void *rx);
+
+/* function to execute a set of tests */
+int spi_test_run_tests(struct spi_device *spi,
+		       struct spi_test *tests);
+
+/* some of the default @spi_transfer.len to test */
+#define ITERATE_LEN 2, 3, 7, 11, 16, 31, 32, 64, 97, 128, 251, 256, \
+		1021, 1024, 1031, 4093, PAGE_SIZE, 4099, 65536, 65537
+
+#define ITERATE_MAX_LEN ITERATE_LEN, SPI_TEST_MAX_SIZE - 1, SPI_TEST_MAX_SIZE
+
+/* the default alignment to test */
+#define ITERATE_ALIGN sizeof(int)

include/linux/spi/spi.h

@@ -768,10 +768,15 @@ struct spi_message {
 	void			*state;
 };
 
+static inline void spi_message_init_no_memset(struct spi_message *m)
+{
+	INIT_LIST_HEAD(&m->transfers);
+}
+
 static inline void spi_message_init(struct spi_message *m)
 {
 	memset(m, 0, sizeof *m);
-	INIT_LIST_HEAD(&m->transfers);
+	spi_message_init_no_memset(m);
 }
 
 static inline void