Merge remote-tracking branches 'spi/topic/dw', 'spi/topic/ep93xx',...

Merge remote-tracking branches 'spi/topic/dw', 'spi/topic/ep93xx', 'spi/topic/falcon' and 'spi/topic/fsl-lpspi' into spi-next

Documentation/spi/ep93xx_spi

-Cirrus EP93xx SPI controller driver HOWTO
-=========================================
-
-ep93xx_spi driver brings SPI master support for EP93xx SPI controller.  Chip
-selects are implemented with GPIO lines.
-
-NOTE: If possible, don't use SFRMOUT (SFRM1) signal as a chip select. It will
-not work correctly (it cannot be controlled by software). Use GPIO lines
-instead.
-
-Sample configuration
-====================
-
-Typically driver configuration is done in platform board files (the files under
-arch/arm/mach-ep93xx/*.c). In this example we configure MMC over SPI through
-this driver on TS-7260 board. You can adapt the code to suit your needs.
-
-This example uses EGPIO9 as SD/MMC card chip select (this is wired in DIO1
-header on the board).
-
-You need to select CONFIG_MMC_SPI to use mmc_spi driver.
-
-arch/arm/mach-ep93xx/ts72xx.c:
-
-...
-#include <linux/gpio.h>
-#include <linux/spi/spi.h>
-
-#include <linux/platform_data/spi-ep93xx.h>
-
-/* this is our GPIO line used for chip select */
-#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO9
-
-static int ts72xx_mmc_spi_setup(struct spi_device *spi)
-{
-	int err;
-
-	err = gpio_request(MMC_CHIP_SELECT_GPIO, spi->modalias);
-	if (err)
-		return err;
-
-	gpio_direction_output(MMC_CHIP_SELECT_GPIO, 1);
-
-	return 0;
-}
-
-static void ts72xx_mmc_spi_cleanup(struct spi_device *spi)
-{
-	gpio_set_value(MMC_CHIP_SELECT_GPIO, 1);
-	gpio_direction_input(MMC_CHIP_SELECT_GPIO);
-	gpio_free(MMC_CHIP_SELECT_GPIO);
-}
-
-static void ts72xx_mmc_spi_cs_control(struct spi_device *spi, int value)
-{
-	gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-}
-
-static struct ep93xx_spi_chip_ops ts72xx_mmc_spi_ops = {
-	.setup		= ts72xx_mmc_spi_setup,
-	.cleanup	= ts72xx_mmc_spi_cleanup,
-	.cs_control	= ts72xx_mmc_spi_cs_control,
-};
-
-static struct spi_board_info ts72xx_spi_devices[] __initdata = {
-	{
-		.modalias		= "mmc_spi",
-		.controller_data	= &ts72xx_mmc_spi_ops,
-		/*
-		 * We use 10 MHz even though the maximum is 7.4 MHz. The driver
-		 * will limit it automatically to max. frequency.
-		 */
-		.max_speed_hz		= 10 * 1000 * 1000,
-		.bus_num		= 0,
-		.chip_select		= 0,
-		.mode			= SPI_MODE_0,
-	},
-};
-
-static struct ep93xx_spi_info ts72xx_spi_info = {
-	.num_chipselect	= ARRAY_SIZE(ts72xx_spi_devices),
-};
-
-static void __init ts72xx_init_machine(void)
-{
-	...
-	ep93xx_register_spi(&ts72xx_spi_info, ts72xx_spi_devices,
-			    ARRAY_SIZE(ts72xx_spi_devices));
-}
-
-The driver can use DMA for the transfers also. In this case ts72xx_spi_info
-becomes:
-
-static struct ep93xx_spi_info ts72xx_spi_info = {
-	.num_chipselect	= ARRAY_SIZE(ts72xx_spi_devices),
-	.use_dma	= true;
-};
-
-Note that CONFIG_EP93XX_DMA should be enabled as well.
-
-Thanks to
-=========
-Martin Guy, H. Hartley Sweeten and others who helped me during development of
-the driver. Simplemachines.it donated me a Sim.One board which I used testing
-the driver on EP9307.

arch/arm/mach-ep93xx/edb93xx.c

@@ -27,7 +27,6 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 #include <linux/spi/spi.h>
@@ -106,33 +105,10 @@ static struct cs4271_platform_data edb93xx_cs4271_data = {
 	.gpio_nreset	= -EINVAL,	/* filled in later */
 };
 
-static int edb93xx_cs4271_hw_setup(struct spi_device *spi)
-{
-	return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6,
-				GPIOF_OUT_INIT_HIGH, spi->modalias);
-}
-
-static void edb93xx_cs4271_hw_cleanup(struct spi_device *spi)
-{
-	gpio_free(EP93XX_GPIO_LINE_EGPIO6);
-}
-
-static void edb93xx_cs4271_hw_cs_control(struct spi_device *spi, int value)
-{
-	gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value);
-}
-
-static struct ep93xx_spi_chip_ops edb93xx_cs4271_hw = {
-	.setup		= edb93xx_cs4271_hw_setup,
-	.cleanup	= edb93xx_cs4271_hw_cleanup,
-	.cs_control	= edb93xx_cs4271_hw_cs_control,
-};
-
 static struct spi_board_info edb93xx_spi_board_info[] __initdata = {
 	{
 		.modalias		= "cs4271",
 		.platform_data		= &edb93xx_cs4271_data,
-		.controller_data	= &edb93xx_cs4271_hw,
 		.max_speed_hz		= 6000000,
 		.bus_num		= 0,
 		.chip_select		= 0,
@@ -140,8 +116,13 @@ static struct spi_board_info edb93xx_spi_board_info[] __initdata = {
 	},
 };
 
+static int edb93xx_spi_chipselects[] __initdata = {
+	EP93XX_GPIO_LINE_EGPIO6,
+};
+
 static struct ep93xx_spi_info edb93xx_spi_info __initdata = {
-	.num_chipselect	= ARRAY_SIZE(edb93xx_spi_board_info),
+	.chipselect	= edb93xx_spi_chipselects,
+	.num_chipselect	= ARRAY_SIZE(edb93xx_spi_chipselects),
 };
 
 static void __init edb93xx_register_spi(void)

arch/arm/mach-ep93xx/simone.c

@@ -48,56 +48,6 @@ static struct ep93xxfb_mach_info __initdata simone_fb_info = {
  */
 #define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0
 
-/*
- * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes
- * low between multi-message command blocks. From v1.4, it uses a GPIO instead.
- * v1.3 parts will still work, since the signal on SFRMOUT is automatic.
- */
-#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO1
-
-/*
- * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal,
- * you can leave these empty and pass NULL as .controller_data.
- */
-
-static int simone_mmc_spi_setup(struct spi_device *spi)
-{
-	unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-	int err;
-
-	err = gpio_request(gpio, spi->modalias);
-	if (err)
-		return err;
-
-	err = gpio_direction_output(gpio, 1);
-	if (err) {
-		gpio_free(gpio);
-		return err;
-	}
-
-	return 0;
-}
-
-static void simone_mmc_spi_cleanup(struct spi_device *spi)
-{
-	unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-
-	gpio_set_value(gpio, 1);
-	gpio_direction_input(gpio);
-	gpio_free(gpio);
-}
-
-static void simone_mmc_spi_cs_control(struct spi_device *spi, int value)
-{
-	gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-}
-
-static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = {
-	.setup		= simone_mmc_spi_setup,
-	.cleanup	= simone_mmc_spi_cleanup,
-	.cs_control	= simone_mmc_spi_cs_control,
-};
-
 /*
  * MMC card detection GPIO setup.
  */
@@ -152,7 +102,6 @@ static struct mmc_spi_platform_data simone_mmc_spi_data = {
 static struct spi_board_info simone_spi_devices[] __initdata = {
 	{
 		.modalias		= "mmc_spi",
-		.controller_data	= &simone_mmc_spi_ops,
 		.platform_data		= &simone_mmc_spi_data,
 		/*
 		 * We use 10 MHz even though the maximum is 3.7 MHz. The driver
@@ -165,8 +114,18 @@ static struct spi_board_info simone_spi_devices[] __initdata = {
 	},
 };
 
+/*
+ * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes
+ * low between multi-message command blocks. From v1.4, it uses a GPIO instead.
+ * v1.3 parts will still work, since the signal on SFRMOUT is automatic.
+ */
+static int simone_spi_chipselects[] __initdata = {
+	EP93XX_GPIO_LINE_EGPIO1,
+};
+
 static struct ep93xx_spi_info simone_spi_info __initdata = {
-	.num_chipselect	= ARRAY_SIZE(simone_spi_devices),
+	.chipselect	= simone_spi_chipselects,
+	.num_chipselect	= ARRAY_SIZE(simone_spi_chipselects),
 	.use_dma = 1,
 };
 

arch/arm/mach-ep93xx/vision_ep9307.c

@@ -175,33 +175,9 @@ static struct cs4271_platform_data vision_cs4271_data = {
 	.gpio_nreset	= EP93XX_GPIO_LINE_H(2),
 };
 
-static int vision_cs4271_hw_setup(struct spi_device *spi)
-{
-	return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6,
-				GPIOF_OUT_INIT_HIGH, spi->modalias);
-}
-
-static void vision_cs4271_hw_cleanup(struct spi_device *spi)
-{
-	gpio_free(EP93XX_GPIO_LINE_EGPIO6);
-}
-
-static void vision_cs4271_hw_cs_control(struct spi_device *spi, int value)
-{
-	gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value);
-}
-
-static struct ep93xx_spi_chip_ops vision_cs4271_hw = {
-	.setup		= vision_cs4271_hw_setup,
-	.cleanup	= vision_cs4271_hw_cleanup,
-	.cs_control	= vision_cs4271_hw_cs_control,
-};
-
 /*************************************************************************
  * SPI Flash
  *************************************************************************/
-#define VISION_SPI_FLASH_CS	EP93XX_GPIO_LINE_EGPIO7
-
 static struct mtd_partition vision_spi_flash_partitions[] = {
 	{
 		.name	= "SPI bootstrap",
@@ -224,68 +200,20 @@ static struct flash_platform_data vision_spi_flash_data = {
 	.nr_parts	= ARRAY_SIZE(vision_spi_flash_partitions),
 };
 
-static int vision_spi_flash_hw_setup(struct spi_device *spi)
-{
-	return gpio_request_one(VISION_SPI_FLASH_CS, GPIOF_INIT_HIGH,
-				spi->modalias);
-}
-
-static void vision_spi_flash_hw_cleanup(struct spi_device *spi)
-{
-	gpio_free(VISION_SPI_FLASH_CS);
-}
-
-static void vision_spi_flash_hw_cs_control(struct spi_device *spi, int value)
-{
-	gpio_set_value(VISION_SPI_FLASH_CS, value);
-}
-
-static struct ep93xx_spi_chip_ops vision_spi_flash_hw = {
-	.setup		= vision_spi_flash_hw_setup,
-	.cleanup	= vision_spi_flash_hw_cleanup,
-	.cs_control	= vision_spi_flash_hw_cs_control,
-};
-
 /*************************************************************************
  * SPI SD/MMC host
  *************************************************************************/
-#define VISION_SPI_MMC_CS	EP93XX_GPIO_LINE_G(2)
-#define VISION_SPI_MMC_WP	EP93XX_GPIO_LINE_F(0)
-#define VISION_SPI_MMC_CD	EP93XX_GPIO_LINE_EGPIO15
-
 static struct mmc_spi_platform_data vision_spi_mmc_data = {
 	.detect_delay	= 100,
 	.powerup_msecs	= 100,
 	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
 	.flags		= MMC_SPI_USE_CD_GPIO | MMC_SPI_USE_RO_GPIO,
-	.cd_gpio	= VISION_SPI_MMC_CD,
+	.cd_gpio	= EP93XX_GPIO_LINE_EGPIO15,
 	.cd_debounce	= 1,
-	.ro_gpio	= VISION_SPI_MMC_WP,
+	.ro_gpio	= EP93XX_GPIO_LINE_F(0),
 	.caps2		= MMC_CAP2_RO_ACTIVE_HIGH,
 };
 
-static int vision_spi_mmc_hw_setup(struct spi_device *spi)
-{
-	return gpio_request_one(VISION_SPI_MMC_CS, GPIOF_INIT_HIGH,
-				spi->modalias);
-}
-
-static void vision_spi_mmc_hw_cleanup(struct spi_device *spi)
-{
-	gpio_free(VISION_SPI_MMC_CS);
-}
-
-static void vision_spi_mmc_hw_cs_control(struct spi_device *spi, int value)
-{
-	gpio_set_value(VISION_SPI_MMC_CS, value);
-}
-
-static struct ep93xx_spi_chip_ops vision_spi_mmc_hw = {
-	.setup		= vision_spi_mmc_hw_setup,
-	.cleanup	= vision_spi_mmc_hw_cleanup,
-	.cs_control	= vision_spi_mmc_hw_cs_control,
-};
-
 /*************************************************************************
  * SPI Bus
  *************************************************************************/
@@ -293,7 +221,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = {
 	{
 		.modalias		= "cs4271",
 		.platform_data		= &vision_cs4271_data,
-		.controller_data	= &vision_cs4271_hw,
 		.max_speed_hz		= 6000000,
 		.bus_num		= 0,
 		.chip_select		= 0,
@@ -301,7 +228,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = {
 	}, {
 		.modalias		= "sst25l",
 		.platform_data		= &vision_spi_flash_data,
-		.controller_data	= &vision_spi_flash_hw,
 		.max_speed_hz		= 20000000,
 		.bus_num		= 0,
 		.chip_select		= 1,
@@ -309,7 +235,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = {
 	}, {
 		.modalias		= "mmc_spi",
 		.platform_data		= &vision_spi_mmc_data,
-		.controller_data	= &vision_spi_mmc_hw,
 		.max_speed_hz		= 20000000,
 		.bus_num		= 0,
 		.chip_select		= 2,
@@ -317,8 +242,15 @@ static struct spi_board_info vision_spi_board_info[] __initdata = {
 	},
 };
 
+static int vision_spi_chipselects[] __initdata = {
+	EP93XX_GPIO_LINE_EGPIO6,
+	EP93XX_GPIO_LINE_EGPIO7,
+	EP93XX_GPIO_LINE_G(2),
+};
+
 static struct ep93xx_spi_info vision_spi_master __initdata = {
-	.num_chipselect	= ARRAY_SIZE(vision_spi_board_info),
+	.chipselect	= vision_spi_chipselects,
+	.num_chipselect	= ARRAY_SIZE(vision_spi_chipselects),
 	.use_dma	= 1,
 };
 

drivers/spi/Kconfig

@@ -264,7 +264,7 @@ config SPI_EP93XX
 	  mode.
 
 config SPI_FALCON
-	tristate "Falcon SPI controller support"
+	bool "Falcon SPI controller support"
 	depends on SOC_FALCON
 	help
 	  The external bus unit (EBU) found on the FALC-ON SoC has SPI

drivers/spi/spi-dw.c

@@ -107,9 +107,9 @@ static const struct file_operations dw_spi_regs_ops = {
 
 static int dw_spi_debugfs_init(struct dw_spi *dws)
 {
-	char name[128];
+	char name[32];
 
-	snprintf(name, 128, "dw_spi-%s", dev_name(&dws->master->dev));
+	snprintf(name, 32, "dw_spi%d", dws->master->bus_num);
 	dws->debugfs = debugfs_create_dir(name, NULL);
 	if (!dws->debugfs)
 		return -ENOMEM;
@@ -486,9 +486,9 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 	dws->type = SSI_MOTO_SPI;
 	dws->dma_inited = 0;
 	dws->dma_addr = (dma_addr_t)(dws->paddr + DW_SPI_DR);
-	snprintf(dws->name, sizeof(dws->name), "dw_spi%d", dws->bus_num);
 
-	ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, dws->name, master);
+	ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, dev_name(dev),
+			  master);
 	if (ret < 0) {
 		dev_err(dev, "can not get IRQ\n");
 		goto err_free_master;

drivers/spi/spi-dw.h

@@ -101,7 +101,6 @@ struct dw_spi_dma_ops {
 struct dw_spi {
 	struct spi_master	*master;
 	enum dw_ssi_type	type;
-	char			name[16];
 
 	void __iomem		*regs;
 	unsigned long		paddr;

drivers/spi/spi-ep93xx.c

@@ -28,6 +28,7 @@
 #include <linux/platform_device.h>
 #include <linux/sched.h>
 #include <linux/scatterlist.h>
+#include <linux/gpio.h>
 #include <linux/spi/spi.h>
 
 #include <linux/platform_data/dma-ep93xx.h>
@@ -107,16 +108,6 @@ struct ep93xx_spi {
 	void				*zeropage;
 };
 
-/**
- * struct ep93xx_spi_chip - SPI device hardware settings
- * @spi: back pointer to the SPI device
- * @ops: private chip operations
- */
-struct ep93xx_spi_chip {
-	const struct spi_device		*spi;
-	struct ep93xx_spi_chip_ops	*ops;
-};
-
 /* converts bits per word to CR0.DSS value */
 #define bits_per_word_to_dss(bpw)	((bpw) - 1)
 
@@ -229,104 +220,36 @@ static int ep93xx_spi_calc_divisors(const struct ep93xx_spi *espi,
 	return -EINVAL;
 }
 
-static void ep93xx_spi_cs_control(struct spi_device *spi, bool control)
-{
-	struct ep93xx_spi_chip *chip = spi_get_ctldata(spi);
-	int value = (spi->mode & SPI_CS_HIGH) ? control : !control;
-
-	if (chip->ops && chip->ops->cs_control)
-		chip->ops->cs_control(spi, value);
-}
-
-/**
- * ep93xx_spi_setup() - setup an SPI device
- * @spi: SPI device to setup
- *
- * This function sets up SPI device mode, speed etc. Can be called multiple
- * times for a single device. Returns %0 in case of success, negative error in
- * case of failure. When this function returns success, the device is
- * deselected.
- */
-static int ep93xx_spi_setup(struct spi_device *spi)
-{
-	struct ep93xx_spi *espi = spi_master_get_devdata(spi->master);
-	struct ep93xx_spi_chip *chip;
-
-	chip = spi_get_ctldata(spi);
-	if (!chip) {
-		dev_dbg(&espi->pdev->dev, "initial setup for %s\n",
-			spi->modalias);
-
-		chip = kzalloc(sizeof(*chip), GFP_KERNEL);
-		if (!chip)
-			return -ENOMEM;
-
-		chip->spi = spi;
-		chip->ops = spi->controller_data;
-
-		if (chip->ops && chip->ops->setup) {
-			int ret = chip->ops->setup(spi);
-
-			if (ret) {
-				kfree(chip);
-				return ret;
-			}
-		}
-
-		spi_set_ctldata(spi, chip);
-	}
-
-	ep93xx_spi_cs_control(spi, false);
-	return 0;
-}
-
-/**
- * ep93xx_spi_cleanup() - cleans up master controller specific state
- * @spi: SPI device to cleanup
- *
- * This function releases master controller specific state for given @spi
- * device.
- */
-static void ep93xx_spi_cleanup(struct spi_device *spi)
+static void ep93xx_spi_cs_control(struct spi_device *spi, bool enable)
 {
-	struct ep93xx_spi_chip *chip;
+	if (spi->mode & SPI_CS_HIGH)
+		enable = !enable;
 
-	chip = spi_get_ctldata(spi);
-	if (chip) {
-		if (chip->ops && chip->ops->cleanup)
-			chip->ops->cleanup(spi);
-		spi_set_ctldata(spi, NULL);
-		kfree(chip);
-	}
+	if (gpio_is_valid(spi->cs_gpio))
+		gpio_set_value(spi->cs_gpio, !enable);
 }
 
-/**
- * ep93xx_spi_chip_setup() - configures hardware according to given @chip
- * @espi: ep93xx SPI controller struct
- * @chip: chip specific settings
- * @speed_hz: transfer speed
- * @bits_per_word: transfer bits_per_word
- */
 static int ep93xx_spi_chip_setup(const struct ep93xx_spi *espi,
-				 const struct ep93xx_spi_chip *chip,
-				 u32 speed_hz, u8 bits_per_word)
+				 struct spi_device *spi,
+				 struct spi_transfer *xfer)
 {
-	u8 dss = bits_per_word_to_dss(bits_per_word);
+	u8 dss = bits_per_word_to_dss(xfer->bits_per_word);
 	u8 div_cpsr = 0;
 	u8 div_scr = 0;
 	u16 cr0;
 	int err;
 
-	err = ep93xx_spi_calc_divisors(espi, speed_hz, &div_cpsr, &div_scr);
+	err = ep93xx_spi_calc_divisors(espi, xfer->speed_hz,
+				       &div_cpsr, &div_scr);
 	if (err)
 		return err;
 
 	cr0 = div_scr << SSPCR0_SCR_SHIFT;
-	cr0 |= (chip->spi->mode & (SPI_CPHA|SPI_CPOL)) << SSPCR0_MODE_SHIFT;
+	cr0 |= (spi->mode & (SPI_CPHA | SPI_CPOL)) << SSPCR0_MODE_SHIFT;
 	cr0 |= dss;
 
 	dev_dbg(&espi->pdev->dev, "setup: mode %d, cpsr %d, scr %d, dss %d\n",
-		chip->spi->mode, div_cpsr, div_scr, dss);
+		spi->mode, div_cpsr, div_scr, dss);
 	dev_dbg(&espi->pdev->dev, "setup: cr0 %#x\n", cr0);
 
 	ep93xx_spi_write_u8(espi, SSPCPSR, div_cpsr);
@@ -603,12 +526,11 @@ static void ep93xx_spi_process_transfer(struct ep93xx_spi *espi,
 					struct spi_message *msg,
 					struct spi_transfer *t)
 {
-	struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi);
 	int err;
 
 	msg->state = t;
 
-	err = ep93xx_spi_chip_setup(espi, chip, t->speed_hz, t->bits_per_word);
+	err = ep93xx_spi_chip_setup(espi, msg->spi, t);
 	if (err) {
 		dev_err(&espi->pdev->dev,
 			"failed to setup chip for transfer\n");
@@ -863,8 +785,13 @@ static int ep93xx_spi_probe(struct platform_device *pdev)
 	struct resource *res;
 	int irq;
 	int error;
+	int i;
 
 	info = dev_get_platdata(&pdev->dev);
+	if (!info) {
+		dev_err(&pdev->dev, "missing platform data\n");
+		return -EINVAL;
+	}
 
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0) {
@@ -882,14 +809,36 @@ static int ep93xx_spi_probe(struct platform_device *pdev)
 	if (!master)
 		return -ENOMEM;
 
-	master->setup = ep93xx_spi_setup;
 	master->transfer_one_message = ep93xx_spi_transfer_one_message;
-	master->cleanup = ep93xx_spi_cleanup;
 	master->bus_num = pdev->id;
-	master->num_chipselect = info->num_chipselect;
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
 
+	master->num_chipselect = info->num_chipselect;
+	master->cs_gpios = devm_kzalloc(&master->dev,
+					sizeof(int) * master->num_chipselect,
+					GFP_KERNEL);
+	if (!master->cs_gpios) {
+		error = -ENOMEM;
+		goto fail_release_master;
+	}
+
+	for (i = 0; i < master->num_chipselect; i++) {
+		master->cs_gpios[i] = info->chipselect[i];
+
+		if (!gpio_is_valid(master->cs_gpios[i]))
+			continue;
+
+		error = devm_gpio_request_one(&pdev->dev, master->cs_gpios[i],
+					      GPIOF_OUT_INIT_HIGH,
+					      "ep93xx-spi");
+		if (error) {
+			dev_err(&pdev->dev, "could not request cs gpio %d\n",
+				master->cs_gpios[i]);
+			goto fail_release_master;
+		}
+	}
+
 	platform_set_drvdata(pdev, master);
 
 	espi = spi_master_get_devdata(master);

drivers/spi/spi-fsl-lpspi.c

@@ -366,7 +366,7 @@ static int fsl_lpspi_transfer_one_msg(struct spi_master *master,
 	struct spi_transfer *xfer;
 	bool is_first_xfer = true;
 	u32 temp;
-	int ret;
+	int ret = 0;
 
 	msg->status = 0;
 	msg->actual_length = 0;

include/linux/platform_data/spi-ep93xx.h

@@ -5,25 +5,14 @@ struct spi_device;
 
 /**
  * struct ep93xx_spi_info - EP93xx specific SPI descriptor
- * @num_chipselect: number of chip selects on this board, must be
- *                  at least one
+ * @chipselect: array of gpio numbers to use as chip selects
+ * @num_chipselect: ARRAY_SIZE(chipselect)
  * @use_dma: use DMA for the transfers
  */
 struct ep93xx_spi_info {
+	int	*chipselect;
 	int	num_chipselect;
 	bool	use_dma;
 };
 
-/**
- * struct ep93xx_spi_chip_ops - operation callbacks for SPI slave device
- * @setup: setup the chip select mechanism
- * @cleanup: cleanup the chip select mechanism
- * @cs_control: control the device chip select
- */
-struct ep93xx_spi_chip_ops {
-	int	(*setup)(struct spi_device *spi);
-	void	(*cleanup)(struct spi_device *spi);
-	void	(*cs_control)(struct spi_device *spi, int value);
-};
-
 #endif /* __ASM_MACH_EP93XX_SPI_H */