Original code would clear the buffer after the firmware had
already been initialized to use the buffer, thus potentially
and inadvertantly clearing data previously DMA'd by the
firmware.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

FCE support enables the firmware to record FC extended link
services and basic link services frames which have been
transmitted and received by the ISP.  This allows for a limited
view of the FC traffic through the ISP without using a FC
analyzer.  This can be useful in situations where a physical
connection to the FC bus is not possible.

The driver exports this information in two ways -- first, via a
debugfs node exported for all supported ISPs under:

	<debugfs_mount_point>/qla2xxx/qla2xxx_<host_no>/fce

where a read of the 'fce' file will provide a snapshot of the
firmware's FCE buffer; and finally, the FCE buffer will be
extracted during a firmware-dump scenario.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

In preparation for FCE (Fibre Channel Event) tracing support.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

- make the following needlessly global code static:
  - qla_attr.c: qla24xx_vport_delete()
  - qla_attr.c: qla24xx_vport_disable()
  - qla_mid.c: qla24xx_allocate_vp_id()
  - qla_mid.c: qla24xx_find_vhost_by_name()
  - qla_mid.c: qla2x00_do_dpc_vp()
  - qla_os.c: struct qla2x00_driver_template
  - qla_os.c: qla2x00_stop_timer()
  - qla_os.c: qla2x00_mem_alloc()
  - qla_os.c: qla2x00_mem_free()
  - qla_sup.c: qla2x00_lock_nvram_access()
  - qla_sup.c: qla2x00_unlock_nvram_access()
  - qla_sup.c: qla2x00_get_nvram_word()
  - qla_sup.c: qla2x00_write_nvram_word()
- #if 0 the following unused global functions:
  - qla_mbx.c: qla2x00_system_error()
- qla_os.c: remove some unneeded function prototypes
- removed unused functions:
  - qla_dbg.c: qla2x00_dump_pkt()
  - qla_mbx.c: qla2x00_get_serdes_params()
  - qla_mbx.c: qla2x00_get_idma_speed()
  - qla_mbx.c: qla24xx_get_vp_database()
  - qla_mbx.c: qla24xx_get_vp_entry()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Small modifications and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

During vport creation, there was a possibility to get create a
vport with same port_name as pport.  A new filter has added to
compare given port_name with the port_name of the pport.
Signed-Off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Instead of abusing the semaphore interfaces for mailbox command
completions.

Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

As the driver depends on the DPC routine to handle bottom-half
loop resynchronization in order to recover from the issue-lip
request.  The issue_lip call is sleeping context capable, so just
issue the reset function there.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Some flash parts have a slow enable write-protection (WP)
operation whereby subsequent FLASH accesses would fail if the WP
operation had not completed.  Software now polls the SPI's
status-register for WP completion.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The driver stores the contents of PCI resources into unsigned
long's before ioremapping. This breaks on 32-bit platforms which
support 64-bit MMIO resources.

Correct code by removing the temporary variables used during MMIO
PIO mapping and using resource_size_t where applicable.  Also
correct a small typo in a printk() where the wrong region number
was displayed.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

HBAs supporting these additional counters include ISP24xx and
ISP25xx type boards.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Drivers do SCRs for each Vport. When something changes in the
fabric, firmware generates one interrupt for each RSCN. Based on
the current implementation, in each case, we make recursive calls
to handle RSCN for physical and each subsequent virtual ports.
The fix is to also take into consideration the vp_idx, which is
set by the firmware to indicate the vport the RSCN was meant for.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Firmware will export to software the maximum number of vports
supported for any given firmware version and ISP type.  Use this
information rather than the current hardcoding of limitations
within the driver.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Callers of qla2x00_async_event() already populate the mb[] array
upon invocation, doing so via the appropriate mailbox register
accessors.  The stale codes removed are leftover-bits kept during
the FWI2 transition.  Though relatively benign, the extra-reads
are not valid for FWI2 boards (ISP24xx and above) and peek into
the incorrect regions of registers.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The original serial-number calculations based on WWPN no longer
apply to newer ISPs (ISP24xx and ISP25xx).  These newer board's
serial number reside in the VPD.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

For recent ISPs, software during CS_UNDERRUN handling must
determine if the two residuals, firmware-calculated and FCP_RSP,
are different to recognize if a frame has been dropped.  Update
the driver to catch this condition, and clear the
SS_RESIDUAL_UNDER and lscsi_status bits.  This logic is
consistent with what earlier firmwares did by explicitly
cracking open the FCP_RSP statuses and clearing
SS_RESIDUAL_UNDER.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Recent ISPs need only the single MMIO BAR to manipulate HW
registers.  Unfortunately, ISP21xx, ISP22xx, ISP23xx, and ISP63xx
type cards still require the I/O mapped region to manipulate the
FLASH via the two HW flash-registers (flash_address and
flash_data).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Fix issue where final flash-segment updates were falling into the slow-path write handler.

Original implementation would not use the burst-write mechanisms
for requests equal to OPTROM_BURST_DWORDS transfer dwords.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Since both NVRAM and VPD regions of the flash reside on unaligned
sector boundaries, during update, the driver must perform a
read-modify-write operation to the composite NVRAM/VPD region.
This affects ISP25xx type boards only.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

As the intermixing may cause issues where HCCR bits could be
cleared inappropriately during MSI/MSI-X interrupt handling.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

drivers/scsi/qla2xxx/qla_sup.c: In function 'qla24xx_write_flash_data':
drivers/scsi/qla2xxx/qla_sup.c:655: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
drivers/scsi/qla2xxx/qla_sup.c: In function 'qla25xx_read_optrom_data':
drivers/scsi/qla2xxx/qla_sup.c:1853: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Do not adjust the iIDMA speed on ports which have a faster
link-speed than the HBA itself.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Since MSI-X vectors do not require a clearing "handshake" from
the system perspective, and the registered handler will not be
called more than once for one occurrence of receipt of a vector,
there is no requirement to flush the risc register write clearing
the interrupt condition in the risc. Also, since the msi-x
registered handlers are optimised for a particular vector, it is
preferable to handle the one vector received per invocation of
the handler.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Make several needlessly global functions static:
- qla2x00_mark_vp_devices_dead()
- qla24xx_configure_vp()

Remove unused function qla24xx_modify_vport().
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Drop usage of legacy to_qla_host() macro.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This change reduces by as much as 16% the memory footprint for
each allocated sbr_t structure requested from the mempool.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Original code, incorrectly passed the address-of a pointer rather
than the pointer value itself.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Also remove legacy '/proc' name during OS_DEVICE_NAME
registration.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Where the DPC logic would get jammed into continuously
reloging-into a port.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>