When CONFIG_HOTPLUG=n the following error occures on vmlinux linkage:

`.exit.text' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.exit.text' of drivers/built-in.o

'rtl8187_disconnect' function marked as __devexit isn't compiled with no
hotplug support. Added __devexit_p macros to fix the problem.
Signed-off-by: NIhar Hrachyshka <ihar.hrachyshka@promwad.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As soon as an interface is enabled, and that interface is in adhoc or master mode,
the device will start raising beacondone interrupts. But before the first interrupt is
raised, mac80211 will probably not have send any beacons to the device yet, which
results in a NULL pointer error when the skb is being freed.

Note that the "raise beacondone interrupts without a beacon" is also a bug,
and will be addressed later. The more important bug however is preventing
the NULL pointer failt itself, since there might be other conditions that could trigger
it as well.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Multiple TX queue support is a core networking feature.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Isolate callers that want to simply reset all the TX qdiscs from the
details of TX queues.

Use this in the ISDN code.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now qdisc, qdisc_sleeping, and qdisc_list also live there.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every qdisc is assosciated with a queue, and in the case of ingress
qdiscs that will now be netdev->rx_queue so using that queue's lock is
the thing to do.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The lock is now an attribute of the device queue.

One thing to notice is that "suspicious" places
emerge which will need specific training about
multiple queue handling.  They are so marked with
explicit "netdev->rx_queue" and "netdev->tx_queue"
references.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some early versions of RTL8187B devices have a USB ID of 0x8187
rather than the 0x8189 of later models. In addition, it appears
that these early units also must be programmed with lower power.
Previous patches used the Product ID string to detect this situation,
but did not address the low power question. This patch uses the
hardware version and sets the power accordingly.
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix some register documentation in the register header files.
This allows better parsing by userspace scripts which in turn
helps debugging.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The gcc 3.4 fork used to compile the MN10300 port emits unwanted
__ucmpdi2() calls for switch statements that use a 64bit value.

This patch removes such a switch from b43legacy, and makes the code
more like that used in b43. Thanks to Adrian Bunk <bunk@kernel.org>
for reporting the problem.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2400 is the only currently available rt2x00 driver which
supports reporting of the RX end time for frames.
Since mac80211 uses this information for IBSS syncing, it
is important that it is being reported.

v2: Complement 32 bits of RX timestamp with upper 32bits from TSF
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the rt2x00 singlethreaded workqueue and move
the link tuner and packet filter scheduled work to
the ieee80211_hw->workqueue again.
The only exception is the interface scheduled work
handler which uses the mac80211 interface iterator
under the RTNL lock. This work needs to be handled
on the kernel workqueue to prevent lockdep issues.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We only need 4 bytes of headroom for alignment
purposes in the RX frame. It was previously higher
for optimization purposes which are no longer
possible due to DMA mappings.

v2: Fix patch error
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the new rfkill interface there is no longer a need
for the input_polldev. Create a delayed_work structure
which we can put on the mac80211 workqueue and poll the
hardware every 1000ms.

v2: Decrease poll frequency from 100ms to 1000ms
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add some error checking to the new beacon configuration code.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <hschaa@suse.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the iwlwifi rfkill. It removes the input device from iwl3945,
adds support for RFKILL_STATE_HARD_BLOCKED and calls rfkill_force_state() to
update the state rather than accessing it directly.
The calls to iwl|iwl3945_rfkill_set_hw_state() had to be moved because
rfkill_force_state() cannot be called from an atomic context.
Tested on iwl3945 and seems to work fine.

Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ivo van Doorn <ivdoorn@gmail.com>
Cc: Fabien Crespel <fcrespel@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NAdel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch sets the block ack request flag if needed
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans rfkill error path. The problem was result of removing
the input device
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hide struct vlan_dev_info from drivers to prevent them from growing
more creative ways to use it. Provide accessors for the two drivers
that currently use it.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some IRDA headers contain references to 'struct pm_dev' that are not
necessary any more and may be removed.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HP OmniBook 500's DSDT code changes the HID of the FIR device from
NSC6001 to HWPC224 when run under an "NT" operating system. Add the
new ID to the pnp device id table.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. dma should be freed when dma2 request fail.
2. dma2 should be freed too when device close.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On embedded devices we must not route the interrupts through
the PCI core, if our host-bus is not PCI.
Reported-by: NSteve Brown <sbrown@cortland.com>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I would like to inform you of our zd1211 based usb wifi adapter (AirTies
WUS-201), which works with the zd1211rw driver with the following device
id definition.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Coverity CID: 2265 NEGATIVE_RETURNS

"rate" is of an unsigned type, and the code requires a signed type.
The following patch makes it so.
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmailcom>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This corrects this kernel.org bug:

	http://bugzilla.kernel.org/show_bug.cgi?id=9701Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vlan_hwaccel_{rx,receive_skb} functions expect the full TCI field
for priority mappings, don't truncate the upper 4 bits.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only a few ISA controllers need the pausing version of the 8390 core
while PCMCIA, later ISA and PCI do not. More importantly the ISA delays
can break non ISA boxes so we must use a different build of 8390.c for
the two sets of controllers.

No changes since last time as all the points of concerns raised proved to
be invalid
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>