Went through the documentation doing typo and content fixes.  This
patch contains only comment and whitespace changes.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Jes complains that page table code still uses lgread_u32 even though
it now uses general kernel pte types.  The best thing to do is to
generalize lgread_u32 and lgwrite_u32.

This means we lose the efficiency of getuser().  We could potentially
regain it if we used __copy_from_user instead of copy_from_user, but
I'm not certain that our range check is equivalent to access_ok() on
all platforms.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NJes Sorensen <jes@sgi.com>

This gets rid of the lguest bus, drivers and DMA mechanism, to make
way for a generic virtio mechanism.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

1) This allows us to get alot closer to booting bzImages.

2) It means we don't have to know page_offset.

3) The Guest needs to modify the boot pagetables to create the
   PAGE_OFFSET mapping before jumping to C code.

4) guest_pa() walks the page tables rather than using page_offset.

5) We don't use page_offset to figure out whether to emulate: it was
   always kinda quesationable, and won't work for instructions done
   before remapping (bzImage unpacking in particular).

6) We still want the kernel address for tlb flushing: have the initial
   hypercall give us that, too.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

(Based on Ron Minnich's LGUEST_PLAN9_SYSCALL patch).

This patch allows Guests to specify what system call vector they want,
and we try to reserve it.  We only allow one non-Linux system call
vector, to try to avoid DoS on the Host.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Move setup_regs() to lguest_arch_setup_regs() in i386_core.c given
that this is very architecture specific.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Clean up the hypercall code to make the code in hypercalls.c
architecture independent. First process the common hypercalls and
then call lguest_arch_do_hcall() if the call hasn't been handled.
Rename struct hcall_ring to hcall_args.

This patch requires the previous patch which reorganize the layout of
struct lguest_regs on i386 so they match the layout of struct
hcall_args.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Currently we look at the "trapnum" to see if the Guest wants a
hypercall.  But once the hypercall is done we have to reset trapnum to
a bogus value, otherwise if we exit to userspace and return, we'd run
the same hypercall twice (that was a nasty bug to find!).

This has two main effects:

1) When Jes's patch changes the hypercall args to be a generic "struct
   hcall_args" we simply change the type of "lg->hcall".  It's set by
   arch code, so if it has to copy args or something it can do so, and
   point "hcall" into lg->arch somewhere.

2) Async hypercalls only get run when an actual hypercall is pending.
   This simplfies the code a little and is a more logical semantic.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Separate i386 architecture specific from core.c and move it to
x86/core.c and add x86/lguest.h header file to match.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>