This patch replaces hexadecimal values by constants for SMBus commands.
Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Datasheet on collision:
	SMBus Collision (SMBCOL_STS)
	This bit is set when a SMBus Collision condition occurs and
	SMBus Host loses in the bus arbitration. The software should
	clear this bit and re-start SMBus operation.

As the status will be cleared in transaction_end, we can remove the
sis630_write and prepare to return -EAGAIN to retry.
Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

The sticky bits must be cleared at the end of the transaction by writing
a 1 to all fields.

Datasheet:
	SMBus Status (SMB_STS)
	The following registers are all sticky bits and only can be
	cleared by writing a one to their corresponding fields.
Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> (for ocores and mux-gpio)
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> (for i2c-gpio)
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> (for puf3)
Acked-by: Barry Song <baohua.song@csr.com> (for sirf)
Reviewed-by: NJean Delvare <khali@linux-fr.org>
[wsa: Fixed "foo* bar" flaws while we are here]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Convert the drivers in drivers/i2c/busses/* to usemodule_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Olof Johansson <olof@lixom.net>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>

module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Convert static struct pci_device_id *[] to static DEFINE_PCI_DEVICE_TABLE
tables.

Use DEFINE_PCI_DEVICE_TABLE ensures we make the pci_device_id table const
and marked as __devinitconst.

This also fixes some warnings from checkpatch:
e.g.
WARNING: Use DEFINE_PCI_DEVICE_TABLE for struct pci_device_id
#1096: FILE: i2c/busses/i2c-intel-mid.c:1096:
+static struct pci_device_id intel_mid_i2c_ids[] = {
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Acked-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

When adding checks for ACPI resource conflicts to many bus drivers,
not enough attention was paid to the error paths, and for several
drivers this causes 0 to be returned on error in some cases. Fix this
by properly returning a non-zero value on every error.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

As warned by checkpatch.pl, <linux/io.h> should be used instead of
<asm/io.h>.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make initialization data also constant.

The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
	struct I1 {
	  ...
	  const struct I2 *x;
	  ...
	};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
	struct I1 y = {
	  .x = E,
	};
@c@
identifier r.I2;
identifier s.E;
@@
	const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+	const
	struct I2 E[] = ...;
// </smpl>
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

These _setup functions are called from _probe so they can be marked
__devinit.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

with while (timeout++ < MAX_TIMEOUT); timeout reaches MAX_TIMEOUT + 1
after the loop, so the tests below are off by one.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Use snprintf instead of sprintf to set adapter names, it's safer.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Check for ACPI resource conflicts in i2c bus drivers. I've included
all recent SMBus master drivers for PC hardware.

I've voluntarily left out:
* Drivers that don't run on PCs: they can't conflict with ACPI.
* Bit-banged bus device drivers: it's very unlikely that ACPI would
  deal with such buses.
Signed-off-by: NJean Delvare <jdelvare@suse.de>

Let general purpose I2C/SMBus bus drivers add SPD to their class. Once
this is done, we will be able to tell the eeprom driver to only probe
for SPD EEPROMs and similar on these buses.

Note that I took a conservative approach here, adding I2C_CLASS_SPD to
many drivers that have no idea whether they can host SPD EEPROMs or not.
This is to make sure that the eeprom driver doesn't stop probing buses
where SPD EEPROMs or equivalent live.

So, bus driver maintainers and users should feel free to remove the SPD
class from drivers those buses never have SPD EEPROMs or they don't
want the eeprom driver to bind to them. Likewise, feel free to add the
SPD class to any bus driver I might have missed.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Many PC SMBus host controller drivers don't properly handle the case
where they are requested to achieve a transaction they do not support.
Update them so that the consistently print a warning message and
return a single error value in this case.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM").  Build tested, with eyeball
review.

One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Globally, s/driverfs/sysfs/g.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

IDs have been defined but not used by most of the I2C adapters.
By having a unique ID, clients can check for correct connection
during probe.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

i2c: Constify i2c_algorithm declarations, part 2

Make struct i2c_algorithm declarations const in all i2c bus drivers
where it is possible.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updates .owner field for various struct pci_driver variables.
Signed-off-by: NLaurent Riffard <laurent.riffard@free.fr>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Clean up name string usage in 12 i2c bus drivers:
* Use the i2c_adapter name for requesting the I/O region rather than
  redefining a new string.
* Do not initialize the i2c_adapter name to "unset".
This should save a few data bytes here and there.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/i2c/busses/i2c-ali1535.c |    6 +++---
 drivers/i2c/busses/i2c-ali1563.c |    6 ++++--
 drivers/i2c/busses/i2c-ali15x3.c |    5 +++--
 drivers/i2c/busses/i2c-amd756.c  |    5 ++---
 drivers/i2c/busses/i2c-amd8111.c |    4 +++-
 drivers/i2c/busses/i2c-i801.c    |    4 ++--
 drivers/i2c/busses/i2c-nforce2.c |    4 ++--
 drivers/i2c/busses/i2c-piix4.c   |    4 ++--
 drivers/i2c/busses/i2c-sis5595.c |    5 +++--
 drivers/i2c/busses/i2c-sis630.c  |    6 ++++--
 drivers/i2c/busses/i2c-sis96x.c  |    5 +++--
 drivers/i2c/busses/i2c-via.c     |    4 ++--
 12 files changed, 33 insertions(+), 25 deletions(-)

Kill explicit static initializations to 0 in 10 i2c drivers.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/i2c/algos/i2c-algo-pca.c    |    2 +-
 drivers/i2c/algos/i2c-algo-sibyte.c |    2 +-
 drivers/i2c/busses/i2c-ali15x3.c    |    4 ++--
 drivers/i2c/busses/i2c-amd756.c     |    2 +-
 drivers/i2c/busses/i2c-iop3xx.c     |    2 +-
 drivers/i2c/busses/i2c-piix4.c      |    8 ++++----
 drivers/i2c/busses/i2c-sis5595.c    |    4 ++--
 drivers/i2c/busses/i2c-sis630.c     |    2 +-
 drivers/i2c/busses/i2c-sis96x.c     |    2 +-
 drivers/i2c/busses/i2c-via.c        |    2 +-
 10 files changed, 15 insertions(+), 15 deletions(-)

There are no more users of i2c_algorithm.id, so we can finally drop
this structure member.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The name member of the i2c_algorithm is never used, although all
drivers conscientiously fill it. We can drop it completely, this
structure doesn't need to have a name.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Files that don't use CONFIG_* stuff shouldn't include config.h
Files that use CONFIG_* stuff should include config.h

It's that simple. ;-)
Signed-off-by: NAlexey Dobriyan <adobriyan@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!