This change updates the ixgbe driver to use __netdev_pick_tx instead of
the current logic it is using to select a queue.  The main result of this
change is that ixgbe can now fully support XPS, and in the case of non-FCoE
enabled configs it means we don't need to have our own ndo_select_queue.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds support for ixgbe to configure the XPS queue mapping on
load.  The result of this change is that on open we will now be resetting
the number of Tx queues, and then setting the default configuration for XPS
based on if ATR is enabled or disabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of adjusting the FCoE and Flow director limits based on the number
of CPUs we can define them much sooner.  This allows the user to come
through later and adjust them once we have updated the code to support the
set_channels ethtool operation.

I am still allowing for FCoE and RSS queues to be separated if the number
queues is less than the number of CPUs.  This essentially treats the two
groupings like they are two separate traffic classes.

In addition I am changing the initialization to use the MAX_TX/RX_QUEUES
defines instead of trying to compute the value as it will be possible in
upcoming patches for the user to request the maximum number of queues.

I have also updated things so that the upper limit on queues is exactly 63
instead of allowing it to go up to 64.  The reason for this change is to
address the fact thqt the driver only supports up to 63 queue vectors since
the hardware supports 64 MSI-X vectors, but one must be reserved for "other"
causes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reshuffles the switch/case structure of the flag assignment to
allow for the flags to be set for each MAC type separately. This is needed
for new HW that does not have feature parity with older HW.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list.  If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using the RTM_GETLINK dump the vlan filter list of a given
bridge port.  The information depends on setting the filter
flag similar to how nic VF info is dumped.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct.  RSC is only supported with IPv4/TCP frames only.  As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.

The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ixgbe set gso_size but not gso_type. This leads to
crashes in macvtap.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change corrects the fact that we were using 1522 to test for the
max frame size in ixgbe_change_mtu and 1518 in ixgbe_set_vf_lpe.  The
difference was the addition of VLAN_HLEN which we only need to add in the case
of computing a buffer size, but not a filter size.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NSibai Li <Sibai.li@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removes the autoneg parameter from the setup_link functions.
Adds local variable autoneg to setup_link functions to be passed
to get_link_capabilities functions if needed.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>

Renames some autoneg/speed variables to be more consistent with check_link,
get_link_capabilities, and setup_link function calls. Initializes instances
of autoneg.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The device lookup neglected to do a pci_dev_put() to decrement the
device reference count.
Reported-by: NElena Gurevich <elena.gurevich@toganetworks.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe claims it supports 64 VFs in its SRIOV capability
structure, but the driver only supports 63.  Adjust it
so sysfs sriov configuration checking will check with
the proper totalvf value.
Signed-off-by: NDonald Dutile <ddutile@redhat.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement callbacks in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV VFs
in a device via the sysfs interface.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is no actual dependency on initialization of the mailbox ops on
whether SR-IOV is enabled or not and it doesn't hurt to go ahead and
initialize ops unconditionally.  Move the initialization into the device
probe so that the mailbox ops are initialized at the time we have the
board info necessary to do it.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <Sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds warnings when a reset of the adapter is scheduled so that the
user can see log of why the reset occurred.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch copies the igb implementation of Tx timestamps, which uses a work
item to poll for the Tx timestamp. In addition it adds a timeout value of 15
seconds, after which it will stop polling.

This is necessary due to an issue with the descriptor being marked done before
the Tx timestamp event has occurred. These two events don't correlate, so using
the done bit on the descriptor as indication that the timestamp must already
have been taken leads to potentially dropped Tx timestamps (especially under
heavy packet load)
Reported-by: NMatthew Vick <matthew.vick@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes ixgbe_ptp_match, and the corresponding packet filtering from
ixgbe driver. This code was previously causing some issues within the hotpath of
the driver. However the code also provided a check against possible frozen Rx
timestamp due to dropped packets when the Rx ring is full. This patch provides a
replacement solution based on the watchdog.

To this end, whenever a packet consumes the Rx timestamp it stores the jiffy
value in the rx_ring structure. Watchdog updates its own jiffy timer whenever
there is no valid timestamp in the registers.

If watchdog detects a valid timestamp in the registers, (meaning that no Rx
packet has consumed it yet) it will check which time is most recent, the last
time in the watchdog, or any time in the rx_rings. If the most recent "event"
was more than 5seconds ago, it will flush the Rx timestamp and print a warning
message to the syslog.
Reported-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map.  To do this I have expanded the work done in the main loop by
pushing first into tx_buffer.  This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor.  The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo.  By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.

To do this I also needed to change the logic and/or drop some flags.  I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do.  Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb.  Instead we can just check the bitflag in the skb.

In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were spending cycles separating the FCoE and TSO contexts even though we
always overwriting the context anyway.  Instead of doing that we can just
use context 0 for all descriptors.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads.  Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
ixgbe_tx_csum call we start with that check as well.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The X540's internal thermal sensor should not be enabled for all devices, but
only those devices which enable it in the NVM image. It is expected that
actively cooled devices will have it enabled, but passively cooled devices might
not want it enabled. This is due to passively cooled devices operating very near
the thermal threshold, sometimes within the margin of error of the thermal
sensor. Thus these devices may not be good candidates for using the thermal
sensor.

This patch uses the enabled bit in the FWSM register to check whether we should
be enabling the thermal sensor, and only sets the THERMAL_SENSOR_CAPABLE flag
for those devices which have it enabled.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the normal kernel test instead of a module specific one.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This change makes it so that only the first fragment in a series of fragments
will have the L4 header pulled.  Previously we were always pulling the L4
header as well and in the case of UDP this can harm performance since only the
first fragment will have the header, the rest just contain data which should
be left in the paged portion of the packet.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the version string to better reflect the driver functionality with
that of the out of tree driver.  Also since we no longer need the MAJ,
MIN, BUILD defines remove them to clean up the code.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The internal bridge mode setting needs to be sticky so that it can be
configured correctly after a device reset.  This change is required now
that the driver supports setting the bridge mode to VEB or VEPA.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <Sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The XOFF received statistic registers are per priority based and not per
traffic class. The ixgbe driver was incorrectly considering them to be for
each traffic class; and then disabling the "Tx hang" check for the queues
that belonged to the particular traffic class that had received PFC frames.

The above logic worked fine in scenario where the user priority and traffic
class number matched e.g. priority 0 is mapped to traffic class 0 and so on.
But, when multiple user priorities are mapped to a single traffic class or
when user priorities and traffic class numbers do not line up; the ixgbe
driver may disable the "Tx hang" check for queues belonging to a traffic
class that did not receive PFC frames and keep the "Tx hang" check enabled
for the queues that did receive the PFC frames.

This patch corrects the above in the code by considering the statistics
on a per priority basis; then getting the traffic class the user priority
belongs to and disabling the "Tx hang" check for queues that belong
to that traffic class.
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we are doing a page based receive there is no point in setting a maximum
packet length on the x540 RXDCTL register.  As such we can drop the code from
the driver entirely.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There was a bitwise operation error in the fdb_add block
that was only allowing FDB types that were not permanent.

This was the opposite of the intent because the hardware
never ages out address these are the _only_ type of addrs
that should be allowed.

This was missed because until recently iproute2 did not
set any bit for this by default. And our test code to
manage FDB entries on embedded devices similarly did not
set these bits.

I am going to chalk this up as a bug and fix it now.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables ethtool to correctly identify flow control (pause
frame) auto negotiation, as well as disallow enabling it when it is not
supported. The ixgbe_device_supports_autoneg_fc function is exported and
used for this purpose.

There is also one minor cleanup of the device_supports_autoneg_fc by
removing an unnecessary return statement.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reformats the output of the Tx/Rx descriptor dumps to more
appropriately align the output of the ixgbe_dump and improve readability.
Prevents empty Tx descriptors from being displayed to decrease the size
of the dump and make it more manageable.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The way the code was previously written it was causing DCA to prefetch the
entire packet into the cache when it was enabled.  That is excessive as we
only really need the headers.

We are now prefetching the headers via software so doing this from DCA would
be redundant anyway.  So clear the bit that was causing us to prefetch the
packet data and instead only use DCA for the descriptor rings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function name should include '_ether_addr'.
Return type should be bool.
Parameter name should be 'addr' not 'dest' (also matching kernel-doc).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:

- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
  as part of net driver modules.  (This also fixes cases where the PTP
  subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
  drivers but are built separately
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>