Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Many platform support this feature, and it can provide significant
power savings when the reduced refresh rate is low.  However, on some
platforms a secondary (reduced) timing is provided but not actually
supported by the hardware.  This results in undesirable flicker at
runtime.

So disable the feature by default, but allow users to opt-in to the
reduced clock behavior with a new module parameter, lvds_downclock,
that can be set to 1 to enable the feature.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NEric Anholt <eric@anholt.net>

Suggested-by: NChris Wilson <chris@chris-wilson.co.uk&gt;>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> (in principle)
Signed-off-by: NEric Anholt <eric@anholt.net>

On Ironlake, there is an interrupt master control bit. With the bit
disabled before clearing IIR, we do not need to handle extra interrupt
in a loop. This patch removes the loop in Ironlake interrupt handler.
It fixed irq lost issue on some Ironlake platforms.

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NZou Nan hai <Nanhai.zou@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

When we setup buffer for display plane, we'll check any pending
required GPU flush and possible make interruptible wait for flush
complete. But that wait would be most possibly to fail in case of
signals received for X process, which will then fail modeset process
and put display engine in unconsistent state. The result could be
blank screen or CPU hang, and DDX driver would always turn on outputs
DPMS after whatever modeset fails or not.

So this one creates new helper for setup display plane buffer, and
when needing flush using uninterruptible wait for that.

This one should fix bug like https://bugs.freedesktop.org/show_bug.cgi?id=24009.
Also fixing mode switch stress test on Ironlake.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

There exist multiple DDC buses for the SDVO cards with multiple outputs.
When we can't get the EDID by using the select DDC bus, we can try the other
possible DDC bus to see whether the EDID can be obtained.

https://bugs.freedesktop.org/show_bug.cgi?id=23842Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Tested-by: NSebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: NEric Anholt <eric@anholt.net>

For some SDVO cards based on conexant chip, we can't read the EDID if
we don't read the response after issuing SDVO DDC bus switch
command.

From the SDVO spec once when another I2C transaction is finished after
completing the I2C transaction of issuing the bus switch command, it
will be switched back to the SDVO internal state again. So we can't
initiate a new I2C transaction to read the response after issuing the
DDC bus switch command. Instead we should issue DDC bus switch command
and read the response in the same I2C transaction.

https://bugs.freedesktop.org/show_bug.cgi?id=23842
https://bugs.freedesktop.org/show_bug.cgi?id=24458
https://bugs.freedesktop.org/show_bug.cgi?id=24522
https://bugs.freedesktop.org/show_bug.cgi?id=24282Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Tested-by: NSebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: NEric Anholt <eric@anholt.net>

On some boxes the BIOS will report different child device arrays when
the system is booted with/without the dock. In such case the HDMI/DP
port can't be setup correctly.  So revert two commits
(fc816655/
6e36595a) that use the child device
parsed from VBT to setup HDMI/DP.

http://bugzilla.kernel.org/show_bug.cgi?id=14854
http://bugzilla.kernel.org/show_bug.cgi?id=14860Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Tested-by: NSean Young <sean@mess.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Commit cbda12d7 (drm/i915: implement
new pm ops for i915), among other things, removed the .suspend and
.resume pointers from the struct drm_driver object in i915_drv.c,
which broke resume without KMS on my MSI Wind U100.

Fix this by reverting that part of commit cbda12d7.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: added comment explaining when .suspend/.resume matter]
Signed-off-by: NEric Anholt <eric@anholt.net>

Without this fix, some modes couldn't find appropriate clocks.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>
Tested-by: NMatthew Garrett <mjg@redhat.com>

For any given clock we can use the find_pll to get the corresponding DPLL
setting. It is unnecessary to use the find_reduce_pll callback function
to calculate the DPLL parameter for LVDS downclock in order to get the same
divider factor(P) for the normal and downclock.

In theory when the LVDS downclock is supported by LVDS panel, we should get the
same DPLL divider factor(P) for the normal clock and reduced downclock.
If we get the diferent divider factor(P) for normal clock and reduced downclock,
it means that the found downclock is incorrect and should be discarded.

So we should use find_pll callback to calculate the DPLL parameter for the
LVDS reduced downclock as for the normal clock. Then we can do the cleanup
about find_reduced_pll.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The HP comaq nx9020/Samsung SX20S laptop always report that the LID status is
closed and we can't use it reliabily for LVDS detection. So add the two boxes
into the quirk list.

http://bugzilla.kernel.org/show_bug.cgi?id=14957
http://bugzilla.kernel.org/show_bug.cgi?id=14554Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

As we removed TV hotplug, don't check its status ever.
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The mask happens to be the same, but the IH is reading the status, not the
not the control register.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If a NULL value is possible, the dereference should only occur after the
NULL test.

Coverity CID: 13338
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If a NULL value is possible, the dereference should only occur after the
NULL test.

Coverity CID: 13335
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If a NULL value is possible, the dereference should only occur after the
NULL test.

Coverity CID: 13334
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The encoder variable can be NULL in this function so I believe it should
be checked before dereference.

Coverity CID: 13253

[airlied: extremely unlikely to happen]
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Stanse found a memory leak in radeon_master_create. master_priv is not
freed/assigned on all paths. Fix that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This always evaluates to true.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This one reverts 9e3a6d15.
As reported by http://bugzilla.kernel.org/show_bug.cgi?id=14485,
this dump will cause hang problem on some machine. If something
really needs this kind of full registers dump, that could be done
within intel-gpu-tools.

Cc: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

For some clocks, the old Ironlake DPLL calculator wold give m/n/p
combinations that didn't match the spreadsheet of what HW validation
tests.  Instead, use the G4X DPLL calculator, which does a better job
at it.

So we use the intel_g4x_find_best_pll to calculate the DPLL for CRT/HDMI/LVDS
on ironlake. At the same time to consider the dpll setting for display port, we
add the display port DPLL limit on ironlake, which will directly use the
function of intel_find_pll_ironlake_dp to get the corresponding dpll setting.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Select the correct BPC for LVDS on Ironlake. If it is 18-bit LVDS panel,
the BPC will be 6. When it is 24-bit LVDS panel, the BPC will 8.
At the same time the BPC will be 8 when the output device is CRT/HDMI/DP.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Enable/disable the dithering for LVDS based on VBT setting. On the 965/g4x
platform the dithering flag is defined in LVDS register. And on the ironlake
the dithering flag is defined in pipeconf register.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

As pinning (allocating and binding GTT memory) does not actually invoke
GPU commands, it is safe, and indeed is attempted, during resumption
from suspension:

  [drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reported-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: NEric Anholt <eric@anholt.net>

Hugh found an error path where we were attempting to unref a bo without
holding the struct mutex:

  [drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
  ------------[ cut here ]------------
  WARNING: at drivers/gpu/drm/drm_gem.c:438 drm_gem_object_free+0x20/0x5e()
  Hardware name: ESPRIMO Mobile V5505
  Modules linked in: snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device
  Pid: 3793, comm: s2ram Not tainted 2.6.33-rc2 #4
  Call Trace:
   [<7815298e>] warn_slowpath_common+0x59/0x6b
   [<781529b3>] warn_slowpath_null+0x13/0x18
   [<78317c1a>] ? drm_gem_object_free+0x20/0x5e
   [<78317c1a>] drm_gem_object_free+0x20/0x5e
   [<78317bfa>] ? drm_gem_object_free+0x0/0x5e
   [<7829df11>] kref_put+0x38/0x45
   [<7833a5f0>] intel_init_clock_gating+0x232/0x271
   [<78317bfa>] ? drm_gem_object_free+0x0/0x5e
   [<7832c307>] i915_restore_state+0x21a/0x2b3
   [<7832379d>] i915_resume+0x3c/0xbb
   [<78174fe5>] ? trace_hardirqs_on_caller+0xfc/0x123
   [<7831c756>] ? drm_class_resume+0x0/0x3e
   [<7831c78d>] drm_class_resume+0x37/0x3e
   [<78351e0a>] legacy_resume+0x1e/0x51
   [<78351ece>] device_resume+0x91/0xab
   [<7831c756>] ? drm_class_resume+0x0/0x3e
   [<78352226>] dpm_resume+0x58/0x10f
   [<783522fb>] dpm_resume_end+0x1e/0x2c
   [<78180f80>] suspend_devices_and_enter+0x61/0x84
   [<78180ff8>] enter_state+0x55/0x83
   [<7818091c>] state_store+0x94/0xaa
   [<7829d09e>] kobj_attr_store+0x1e/0x23
   [<782098e0>] sysfs_write_file+0x66/0x99
   [<781cd2f0>] vfs_write+0x8a/0x108
   [<781cd408>] sys_write+0x3c/0x63
   [<78125c10>] sysenter_do_call+0x12/0x36
  ---[ end trace a343537f29950fda ]---

It is in fact slightly more insiduous that first appears since we are
attempting to not just free the object without the lock, but are trying
to do the whole bo manipulation without holding the lock.
Reported-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: NEric Anholt <eric@anholt.net>

drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load':
drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function

Partly this is because gcc isn't smart enough.  But `ll_base' does get used
uninitialised in the DRM_DEBUG() call.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

This code generally fails to adjust the render clock, and when it does,
it conflicts with some other register settings and can cause problems.

So remove this code altogether.  I'm reworking it now to do the right
thing, but the only bit it will share is the VBT check for whether
reclocking is supported, so I'm leaving that bit.

Reverts most of 652c393a ("add dynamic
clock frequency control"), though for many the regressions showed up
in the later 181a5336 ("Fix render
reclock availability detection").
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

We restored RC6 twice on resume, even with modesetting off.  Instead,
only restore it once and skip RC6 initialization entirely in non-KMS mode.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Tested-by: NJeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch adds a new execbuf ioctl, execbuf2, for use by clients that
want to control fence register allocation more finely.  The buffer
passed in to the new ioctl includes a new relocation type to indicate
whether a given object needs a fence register assigned for the command
buffer in question.

Compatibility with the existing execbuf ioctl is implemented in terms
of the new code, preserving the assumption that fence registers are
required for pre-965 rendering commands.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: Remove pre-emptive clear_fence_reg()]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
[anholt: Removed dmesg spam]
Signed-off-by: NEric Anholt <eric@anholt.net>

Should fix fdo bug 25741
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Look up primary dac adj values from the table if
there is no bios or bios dac table to reference.

The lookup table may need to be adjusted for certain
families.

Should fix kernel bug 14945.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

if necessary for combios

Some early combios radeon cards don't have a connector
table or dac table in the bios, if they do not, fallback
to the default tables.

Should fix kernel bug 14963.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

[airlied: just adding this for completeness to avoid drift between
public atombios.h files]
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>