From f04ddfcd24bf3c1f987eaf634a84998044e616d3 Mon Sep 17 00:00:00 2001 From: Denis Turischev Date: Mon, 14 Mar 2011 12:53:05 +0200 Subject: [PATCH] gpio: Add Tunnel Creek support to sch_gpio Almost the same driver for both Poulsbo and Tunnel Creek. The difference is in quantity of GPIOs powered by the core power rail and by suspend power supply, default values for some GPIOs, etc. Detect actual hardware by platform device ID assigned in lpc_sch and set configuration accordingly. Signed-off-by: Denis Turischev Acked-by: Grant Likely Signed-off-by: Samuel Ortiz --- drivers/gpio/Kconfig | 7 +++-- drivers/gpio/sch_gpio.c | 57 ++++++++++++++++++++++++++++------------- 2 files changed, 44 insertions(+), 20 deletions(-) diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index b46442d7d66e..d8d0cda2641d 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -100,18 +100,21 @@ config GPIO_VR41XX Say yes here to support the NEC VR4100 series General-purpose I/O Uint config GPIO_SCH - tristate "Intel SCH GPIO" + tristate "Intel SCH/TunnelCreek GPIO" depends on GPIOLIB && PCI && X86 select MFD_CORE select LPC_SCH help - Say yes here to support GPIO interface on Intel Poulsbo SCH. + Say yes here to support GPIO interface on Intel Poulsbo SCH + or Intel Tunnel Creek processor. The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are powered by the core power rail and are turned off during sleep modes (S3 and higher). The remaining four GPIOs are powered by the Intel SCH suspend power supply. These GPIOs remain active during S3. The suspend powered GPIOs can be used to wake the system from the Suspend-to-RAM state. + The Intel Tunnel Creek processor has 5 GPIOs powered by the + core power rail and 9 from suspend power supply. This driver can also be built as a module. If so, the module will be called sch-gpio. diff --git a/drivers/gpio/sch_gpio.c b/drivers/gpio/sch_gpio.c index 583521352c16..56060421cdff 100644 --- a/drivers/gpio/sch_gpio.c +++ b/drivers/gpio/sch_gpio.c @@ -25,6 +25,7 @@ #include #include #include +#include #include @@ -187,7 +188,11 @@ static struct gpio_chip sch_gpio_resume = { static int __devinit sch_gpio_probe(struct platform_device *pdev) { struct resource *res; - int err; + int err, id; + + id = pdev->id; + if (!id) + return -ENODEV; res = platform_get_resource(pdev, IORESOURCE_IO, 0); if (!res) @@ -198,12 +203,40 @@ static int __devinit sch_gpio_probe(struct platform_device *pdev) gpio_ba = res->start; - sch_gpio_core.base = 0; - sch_gpio_core.ngpio = 10; - sch_gpio_core.dev = &pdev->dev; + switch (id) { + case PCI_DEVICE_ID_INTEL_SCH_LPC: + sch_gpio_core.base = 0; + sch_gpio_core.ngpio = 10; + + sch_gpio_resume.base = 10; + sch_gpio_resume.ngpio = 4; + + /* + * GPIO[6:0] enabled by default + * GPIO7 is configured by the CMC as SLPIOVR + * Enable GPIO[9:8] core powered gpios explicitly + */ + outb(0x3, gpio_ba + CGEN + 1); + /* + * SUS_GPIO[2:0] enabled by default + * Enable SUS_GPIO3 resume powered gpio explicitly + */ + outb(0x8, gpio_ba + RGEN); + break; + + case PCI_DEVICE_ID_INTEL_ITC_LPC: + sch_gpio_core.base = 0; + sch_gpio_core.ngpio = 5; + + sch_gpio_resume.base = 5; + sch_gpio_resume.ngpio = 9; + break; + + default: + return -ENODEV; + } - sch_gpio_resume.base = 10; - sch_gpio_resume.ngpio = 4; + sch_gpio_core.dev = &pdev->dev; sch_gpio_resume.dev = &pdev->dev; err = gpiochip_add(&sch_gpio_core); @@ -214,18 +247,6 @@ static int __devinit sch_gpio_probe(struct platform_device *pdev) if (err < 0) goto err_sch_gpio_resume; - /* - * GPIO[6:0] enabled by default - * GPIO7 is configured by the CMC as SLPIOVR - * Enable GPIO[9:8] core powered gpios explicitly - */ - outb(0x3, gpio_ba + CGEN + 1); - /* - * SUS_GPIO[2:0] enabled by default - * Enable SUS_GPIO3 resume powered gpio explicitly - */ - outb(0x8, gpio_ba + RGEN); - return 0; err_sch_gpio_resume: -- GitLab