sdhci: avoid changing voltage needlessly

Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

drivers/mmc/host/sdhci.c

@@ -1005,50 +1005,53 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned short power)
 {
 	u8 pwr;
 
-	if (host->power == power)
-		return;
-
-	if (power == (unsigned short)-1) {
-		sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
-		goto out;
-	}
-
-	/*
-	 * Spec says that we should clear the power reg before setting
-	 * a new value. Some controllers don't seem to like this though.
-	 */
-	if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
-		sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
-
-	pwr = SDHCI_POWER_ON;
-
+	if (power == (unsigned short)-1)
+		pwr = 0;
+	else {
 		switch (1 << power) {
 		case MMC_VDD_165_195:
-		pwr |= SDHCI_POWER_180;
+			pwr = SDHCI_POWER_180;
 			break;
 		case MMC_VDD_29_30:
 		case MMC_VDD_30_31:
-		pwr |= SDHCI_POWER_300;
+			pwr = SDHCI_POWER_300;
 			break;
 		case MMC_VDD_32_33:
 		case MMC_VDD_33_34:
-		pwr |= SDHCI_POWER_330;
+			pwr = SDHCI_POWER_330;
 			break;
 		default:
 			BUG();
 		}
+	}
+
+	if (host->pwr == pwr)
+		return;
+
+	host->pwr = pwr;
+
+	if (pwr == 0) {
+		sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
+		return;
+	}
+
+	/*
+	 * Spec says that we should clear the power reg before setting
+	 * a new value. Some controllers don't seem to like this though.
+	 */
+	if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
+		sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
 
 	/*
 	 * At least the Marvell CaFe chip gets confused if we set the voltage
 	 * and set turn on power at the same time, so set the voltage first.
 	 */
 	if ((host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER))
-		sdhci_writeb(host, pwr & ~SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
-
 		sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
 
-out:
-	host->power = power;
+	pwr |= SDHCI_POWER_ON;
+
+	sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
 }
 
 /*****************************************************************************\

drivers/mmc/host/sdhci.h

@@ -255,7 +255,7 @@ struct sdhci_host {
 	unsigned int		timeout_clk;	/* Timeout freq (KHz) */
 
 	unsigned int		clock;		/* Current clock (MHz) */
-	unsigned short		power;		/* Current voltage */
+	u8			pwr;		/* Current voltage */
 
 	struct mmc_request	*mrq;		/* Current request */
 	struct mmc_command	*cmd;		/* Current command */