From 9a4178b76a973684750d20b684bae4f57ab9a355 Mon Sep 17 00:00:00 2001 From: "shane.seymour" Date: Sat, 18 Jul 2015 11:13:09 -0500 Subject: [PATCH] hpsa: fix issues with multilun devices A regression was introduced into the hpsa driver a while back so non-zero LUNs of multi-LUN devices may no longer be presented via a SAS based Smart Array. I have not done a bisection to discover the change that caused it. The CISS firmware specification (available on sourceforge) defines an 8 byte lunid that describes devices that the Smart Array can see/present to the system. The current code in the hpsa driver attempts to find matches for non-zero LUNs with LUN 0 for a bus/target by zeroing out byte 4 of the lunid and find a match. This method is sufficient for SCSI based Smart Arrays because byte 5 is always 0. For SAS based Smart arrays byte 5 of the lunid contains the path number for a multipath device and either one or two bits (the documentation does not define how many bits are used but it appears it may be one only) that indicate if the given path number in byte 5 must always be used to access that device. Byte 5 may not always be zero. The following are lunids (spaces added for clarity) for a MSL2024 single drive library connected via a H241 Smart Array: 00 00 00 00 01 00 00 01 (changer) 00 00 00 00 00 80 00 01 (tape) In the 4th byte (counting from 0) you can see that the tape is LUN 0 and the changer is LUN 1. The 0x80 set in the 5th byte for the tape drive means the driver should force access to path 0 (the library in this case was connected to one path only anyway). After the changes we can see the following in the dmesg output: scsi 0:3:0:0: RAID HP H241 1.18 \ PQ: 0 ANSI: 5 scsi 0:2:0:0: Sequential-Access HP Ultrium 6-SCSI 354W \ PQ: 0 ANSI: 6 scsi 0:2:0:1: Medium Changer HP MSL G3 Series 8.70 \ PQ: 0 ANSI: 5 Showing that the changer is correctly identified as LUN 1 of bus 2 target 0. Before the change the changer device is not seen. Suggested-by: shane.seymour Reviewed-by: Kevin Barnett Reviewed-by: Scott Teel Reviewed-by: Tomas Henzl Signed-off-by: Don Brace Signed-off-by: James Bottomley --- drivers/scsi/hpsa.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c index 07512463b990..3f1c2a88b204 100644 --- a/drivers/scsi/hpsa.c +++ b/drivers/scsi/hpsa.c @@ -1187,17 +1187,19 @@ static int hpsa_scsi_add_entry(struct ctlr_info *h, int hostno, /* This is a non-zero lun of a multi-lun device. * Search through our list and find the device which - * has the same 8 byte LUN address, excepting byte 4. + * has the same 8 byte LUN address, excepting byte 4 and 5. * Assign the same bus and target for this new LUN. * Use the logical unit number from the firmware. */ memcpy(addr1, device->scsi3addr, 8); addr1[4] = 0; + addr1[5] = 0; for (i = 0; i < n; i++) { sd = h->dev[i]; memcpy(addr2, sd->scsi3addr, 8); addr2[4] = 0; - /* differ only in byte 4? */ + addr2[5] = 0; + /* differ only in byte 4 and 5? */ if (memcmp(addr1, addr2, 8) == 0) { device->bus = sd->bus; device->target = sd->target; -- GitLab