diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 2d299bf5d72fc05085dacf6ce5bcb20d9c02e1ea..8cbc3aae6c648ee688fadfac2badf0d37e7e81bf 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -3,9 +3,6 @@ if ARCH_AT91 config HAVE_AT91_DATAFLASH_CARD bool -config HAVE_NAND_ATMEL_BUSWIDTH_16 - bool - config HAVE_AT91_USART3 bool @@ -209,7 +206,6 @@ comment "AT91SAM9260 / AT91SAM9XE Board Type" config MACH_AT91SAM9260EK bool "Atmel AT91SAM9260-EK / AT91SAM9XE Evaluation Kit" select HAVE_AT91_DATAFLASH_CARD - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit @@ -270,7 +266,6 @@ comment "AT91SAM9261 Board Type" config MACH_AT91SAM9261EK bool "Atmel AT91SAM9261-EK Evaluation Kit" select HAVE_AT91_DATAFLASH_CARD - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit. @@ -286,7 +281,6 @@ comment "AT91SAM9G10 Board Type" config MACH_AT91SAM9G10EK bool "Atmel AT91SAM9G10-EK Evaluation Kit" select HAVE_AT91_DATAFLASH_CARD - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9G10-EK Evaluation Kit. @@ -302,7 +296,6 @@ comment "AT91SAM9263 Board Type" config MACH_AT91SAM9263EK bool "Atmel AT91SAM9263-EK Evaluation Kit" select HAVE_AT91_DATAFLASH_CARD - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit. @@ -343,7 +336,6 @@ comment "AT91SAM9G20 Board Type" config MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit" select HAVE_AT91_DATAFLASH_CARD - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit that embeds only one SD/MMC slot. @@ -351,7 +343,6 @@ config MACH_AT91SAM9G20EK config MACH_AT91SAM9G20EK_2MMC depends on MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots" - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and @@ -416,7 +407,6 @@ comment "AT91SAM9G45 Board Type" config MACH_AT91SAM9M10G45EK bool "Atmel AT91SAM9M10G45-EK Evaluation Kits" - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit. "ES" at the end of the name means that this board is an @@ -433,7 +423,6 @@ comment "AT91CAP9 Board Type" config MACH_AT91CAP9ADK bool "Atmel AT91CAP9A-DK Evaluation Kit" select HAVE_AT91_DATAFLASH_CARD - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91CAP9A-DK Evaluation Kit. @@ -450,7 +439,6 @@ config MACH_AT572D940HFEB bool "AT572D940HF-EK" depends on ARCH_AT572D940HF select HAVE_AT91_DATAFLASH_CARD - select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT572D940HF-EK evaluation kit. @@ -483,13 +471,6 @@ config MTD_AT91_DATAFLASH_CARD help Enable support for the DataFlash card. -config MTD_NAND_ATMEL_BUSWIDTH_16 - bool "Enable 16-bit data bus interface to NAND flash" - depends on HAVE_NAND_ATMEL_BUSWIDTH_16 - help - On AT91SAM926x boards both types of NAND flash can be present - (8 and 16 bit data bus width). - # ---------------------------------------------------------- comment "AT91 Feature Selections" diff --git a/arch/arm/mach-at91/board-at572d940hf_ek.c b/arch/arm/mach-at91/board-at572d940hf_ek.c index 3929f1c9e4e5ce0fe10bb8ba64c02d4eae27aaed..096b99f4b1f336b8d10ab49c975201ffcee89c89 100644 --- a/arch/arm/mach-at91/board-at572d940hf_ek.c +++ b/arch/arm/mach-at91/board-at572d940hf_ek.c @@ -41,6 +41,7 @@ #include #include #include +#include #include "sam9_smc.h" #include "generic.h" @@ -216,11 +217,6 @@ static struct atmel_nand_data __initdata eb_nand_data = { /* .rdy_pin = AT91_PIN_PC16, */ .enable_pin = AT91_PIN_PA15, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif }; static struct sam9_smc_config __initdata eb_nand_smc_config = { @@ -243,6 +239,7 @@ static struct sam9_smc_config __initdata eb_nand_smc_config = { static void __init eb_add_device_nand(void) { + ek_nand_data.bus_width_16 = !board_have_nand_8bit(); /* setup bus-width (8 or 16) */ if (eb_nand_data.bus_width_16) eb_nand_smc_config.mode |= AT91_SMC_DBW_16; diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c index e7274440ead99f8970e2abc801d2d752dced6d90..96010d4e15af182f72fccaf6e6329c0e969eae0f 100644 --- a/arch/arm/mach-at91/board-cap9adk.c +++ b/arch/arm/mach-at91/board-cap9adk.c @@ -44,6 +44,7 @@ #include #include #include +#include #include "sam9_smc.h" #include "generic.h" @@ -187,11 +188,6 @@ static struct atmel_nand_data __initdata cap9adk_nand_data = { // .rdy_pin = ... not connected .enable_pin = AT91_PIN_PD15, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif }; static struct sam9_smc_config __initdata cap9adk_nand_smc_config = { @@ -219,6 +215,7 @@ static void __init cap9adk_add_device_nand(void) csa = at91_sys_read(AT91_MATRIX_EBICSA); at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V); + cap9adk_nand_data.bus_width_16 = !board_have_nand_8bit(); /* setup bus-width (8 or 16) */ if (cap9adk_nand_data.bus_width_16) cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_16; diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index de1816e0e1d967c87825bf6c4de11c8370aaf057..fdfa144cbe769bc40e7469a4eb9527d184131f95 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -44,6 +44,7 @@ #include #include #include +#include #include "sam9_smc.h" #include "generic.h" @@ -191,11 +192,6 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif }; static struct sam9_smc_config __initdata ek_nand_smc_config = { @@ -218,6 +214,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { + ek_nand_data.bus_width_16 = !board_have_nand_8bit(); /* setup bus-width (8 or 16) */ if (ek_nand_data.bus_width_16) ek_nand_smc_config.mode |= AT91_SMC_DBW_16; diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 14acc901e24cdd97ca4c939f5ae3bcfba189feff..c2773b5f2eeec5d6593298d206dda570753c2040 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -48,6 +48,7 @@ #include #include #include +#include #include "sam9_smc.h" #include "generic.h" @@ -197,11 +198,6 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PC15, .enable_pin = AT91_PIN_PC14, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif }; static struct sam9_smc_config __initdata ek_nand_smc_config = { @@ -224,6 +220,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { + ek_nand_data.bus_width_16 = !board_have_nand_8bit(); /* setup bus-width (8 or 16) */ if (ek_nand_data.bus_width_16) ek_nand_smc_config.mode |= AT91_SMC_DBW_16; diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index bfe490df58be9edf63ab20b001ccaf94c368ccd1..1dabc0ae56c93153a758263657a2e89b30ac19d8 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -47,6 +47,7 @@ #include #include #include +#include #include "sam9_smc.h" #include "generic.h" @@ -198,11 +199,6 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PA22, .enable_pin = AT91_PIN_PD15, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif }; static struct sam9_smc_config __initdata ek_nand_smc_config = { @@ -225,6 +221,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { + ek_nand_data.bus_width_16 = !board_have_nand_8bit(); /* setup bus-width (8 or 16) */ if (ek_nand_data.bus_width_16) ek_nand_smc_config.mode |= AT91_SMC_DBW_16; diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index ca8198b3c168bb8a333dc3d08102b082a73e66c4..d13acd5c92f218199b0317cbabcbc57a9859cd32 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -43,6 +43,7 @@ #include #include #include +#include #include "sam9_smc.h" #include "generic.h" @@ -175,11 +176,6 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif }; static struct sam9_smc_config __initdata ek_nand_smc_config = { @@ -202,6 +198,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { + ek_nand_data.bus_width_16 = !board_have_nand_8bit(); /* setup bus-width (8 or 16) */ if (ek_nand_data.bus_width_16) ek_nand_smc_config.mode |= AT91_SMC_DBW_16; diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index 6c999dbd2bcfb20427387767dc5bdb623c48a489..49d6849f0ccb55db304f26bef4d9631d73bde2d9 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -41,6 +41,7 @@ #include #include #include +#include #include "sam9_smc.h" #include "generic.h" @@ -155,11 +156,6 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PC8, .enable_pin = AT91_PIN_PC14, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif }; static struct sam9_smc_config __initdata ek_nand_smc_config = { @@ -182,6 +178,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { + ek_nand_data.bus_width_16 = !board_have_nand_8bit(); /* setup bus-width (8 or 16) */ if (ek_nand_data.bus_width_16) ek_nand_smc_config.mode |= AT91_SMC_DBW_16; diff --git a/arch/arm/mach-at91/include/mach/system_rev.h b/arch/arm/mach-at91/include/mach/system_rev.h new file mode 100644 index 0000000000000000000000000000000000000000..b855ee75f72cec84a63650a9de3eb3515d8c890e --- /dev/null +++ b/arch/arm/mach-at91/include/mach/system_rev.h @@ -0,0 +1,25 @@ +/* + * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD + * + * Under GPLv2 only + */ + +#ifndef __ARCH_SYSTEM_REV_H__ +#define __ARCH_SYSTEM_REV_H__ + +/* + * board revision encoding + * mach specific + * the 16-31 bit are reserved for at91 generic information + * + * bit 31: + * 0 => nand 16 bit + * 1 => nand 8 bit + */ +#define BOARD_HAVE_NAND_8BIT (1 << 31) +static int inline board_have_nand_8bit(void) +{ + return system_rev & BOARD_HAVE_NAND_8BIT; +} + +#endif /* __ARCH_SYSTEM_REV_H__ */