[ARM] 3242/2: AT91RM9200 support for 2.6 (Serial)

Patch from Andrew Victor

This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.

This patch is the Serial driver.

This version uses the newly re-written GPL'ed hardware headers.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

drivers/serial/Kconfig

@@ -280,6 +280,40 @@ config SERIAL_AMBA_PL011_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
+config SERIAL_AT91
+	bool "AT91RM9200 serial port support"
+	depends on ARM && ARCH_AT91RM9200
+	select SERIAL_CORE
+	help
+	  This enables the driver for the on-chip UARTs of the AT91RM9200
+	  processor.
+
+config SERIAL_AT91_CONSOLE
+	bool "Support for console on AT91RM9200 serial port"
+	depends on SERIAL_AT91=y
+	select SERIAL_CORE_CONSOLE
+	help
+	  Say Y here if you wish to use a UART on the AT91RM9200 as the system
+	  console (the system console is the device which receives all kernel
+	  messages and warnings and which allows logins in single user mode).
+
+config SERIAL_AT91_TTYAT
+	bool "Install as device ttyAT0-4 instead of ttyS0-4"
+	depends on SERIAL_AT91=y
+	help
+	  Say Y here if you wish to have the five internal AT91RM9200 UARTs
+	  appear as /dev/ttyAT0-4 (major 240, minor 0-4) instead of the
+	  normal /dev/ttyS0-4 (major 4, minor 64-68). This is necessary if
+	  you also want other UARTs, such as external 8250/16C550 compatible
+	  UARTs.
+	  The ttySn nodes are legally reserved for the 8250 serial driver
+	  but are often misused by other serial drivers.
+
+	  To use this, you should create suitable ttyATn device nodes in
+	  /dev/, and pass "console=ttyATn" to the kernel.
+
+	  Say Y if you have an external 8250/16C550 UART.  If unsure, say N.
+
 config SERIAL_CLPS711X
 	tristate "CLPS711X serial port support"
 	depends on ARM && ARCH_CLPS711X

drivers/serial/Makefile

@@ -56,3 +56,4 @@ obj-$(CONFIG_SERIAL_JSM) += jsm/
 obj-$(CONFIG_SERIAL_TXX9) += serial_txx9.o
 obj-$(CONFIG_SERIAL_VR41XX) += vr41xx_siu.o
 obj-$(CONFIG_SERIAL_SGI_IOC4) += ioc4_serial.o
+obj-$(CONFIG_SERIAL_AT91) += at91_serial.o

drivers/serial/at91_serial.c

+/*
+ *  linux/drivers/char/at91_serial.c
+ *
+ *  Driver for Atmel AT91RM9200 Serial ports
+ *
+ *  Copyright (C) 2003 Rick Bronson
+ *
+ *  Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
+ *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/tty.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/serial.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/tty_flip.h>
+
+#include <asm/io.h>
+
+#include <asm/arch/at91rm9200_usart.h>
+#include <asm/mach/serial_at91rm9200.h>
+#include <asm/arch/board.h>
+#include <asm/arch/pio.h>
+
+
+#if defined(CONFIG_SERIAL_AT91_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/serial_core.h>
+
+#ifdef CONFIG_SERIAL_AT91_TTYAT
+
+/* Use device name ttyAT, major 204 and minor 154-169.  This is necessary if we
+ * should coexist with the 8250 driver, such as if we have an external 16C550
+ * UART. */
+#define SERIAL_AT91_MAJOR	204
+#define MINOR_START		154
+#define AT91_DEVICENAME		"ttyAT"
+
+#else
+
+/* Use device name ttyS, major 4, minor 64-68.  This is the usual serial port
+ * name, but it is legally reserved for the 8250 driver. */
+#define SERIAL_AT91_MAJOR	TTY_MAJOR
+#define MINOR_START		64
+#define AT91_DEVICENAME		"ttyS"
+
+#endif
+
+#define AT91_VA_BASE_DBGU	((unsigned long) AT91_VA_BASE_SYS + AT91_DBGU)
+#define AT91_ISR_PASS_LIMIT	256
+
+#define UART_PUT_CR(port,v)	writel(v, (port)->membase + AT91_US_CR)
+#define UART_GET_MR(port)	readl((port)->membase + AT91_US_MR)
+#define UART_PUT_MR(port,v)	writel(v, (port)->membase + AT91_US_MR)
+#define UART_PUT_IER(port,v)	writel(v, (port)->membase + AT91_US_IER)
+#define UART_PUT_IDR(port,v)	writel(v, (port)->membase + AT91_US_IDR)
+#define UART_GET_IMR(port)	readl((port)->membase + AT91_US_IMR)
+#define UART_GET_CSR(port)	readl((port)->membase + AT91_US_CSR)
+#define UART_GET_CHAR(port)	readl((port)->membase + AT91_US_RHR)
+#define UART_PUT_CHAR(port,v)	writel(v, (port)->membase + AT91_US_THR)
+#define UART_GET_BRGR(port)	readl((port)->membase + AT91_US_BRGR)
+#define UART_PUT_BRGR(port,v)	writel(v, (port)->membase + AT91_US_BRGR)
+#define UART_PUT_RTOR(port,v)	writel(v, (port)->membase + AT91_US_RTOR)
+
+// #define UART_GET_CR(port)	readl((port)->membase + AT91_US_CR)		// is write-only
+
+ /* PDC registers */
+#define UART_PUT_PTCR(port,v)	writel(v, (port)->membase + AT91_PDC_PTCR)
+#define UART_PUT_RPR(port,v)	writel(v, (port)->membase + AT91_PDC_RPR)
+#define UART_PUT_RCR(port,v)	writel(v, (port)->membase + AT91_PDC_RCR)
+#define UART_GET_RCR(port)	readl((port)->membase + AT91_PDC_RCR)
+#define UART_PUT_RNPR(port,v)	writel(v, (port)->membase + AT91_PDC_RNPR)
+#define UART_PUT_RNCR(port,v)	writel(v, (port)->membase + AT91_PDC_RNCR)
+
+
+static int (*at91_open)(struct uart_port *);
+static void (*at91_close)(struct uart_port *);
+
+#ifdef SUPPORT_SYSRQ
+static struct console at91_console;
+#endif
+
+/*
+ * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
+ */
+static u_int at91_tx_empty(struct uart_port *port)
+{
+	return (UART_GET_CSR(port) & AT91_US_TXEMPTY) ? TIOCSER_TEMT : 0;
+}
+
+/*
+ * Set state of the modem control output lines
+ */
+static void at91_set_mctrl(struct uart_port *port, u_int mctrl)
+{
+	unsigned int control = 0;
+
+	/*
+	 * Errata #39: RTS0 is not internally connected to PA21.  We need to drive
+	 *  the pin manually.
+	 */
+	if (port->mapbase == AT91_VA_BASE_US0) {
+		if (mctrl & TIOCM_RTS)
+			at91_sys_write(AT91_PIOA + PIO_CODR, AT91_PA21_RTS0);
+		else
+			at91_sys_write(AT91_PIOA + PIO_SODR, AT91_PA21_RTS0);
+	}
+
+	if (mctrl & TIOCM_RTS)
+		control |= AT91_US_RTSEN;
+	else
+		control |= AT91_US_RTSDIS;
+
+	if (mctrl & TIOCM_DTR)
+		control |= AT91_US_DTREN;
+	else
+		control |= AT91_US_DTRDIS;
+
+	UART_PUT_CR(port,control);
+}
+
+/*
+ * Get state of the modem control input lines
+ */
+static u_int at91_get_mctrl(struct uart_port *port)
+{
+	unsigned int status, ret = 0;
+
+	status = UART_GET_CSR(port);
+
+	/*
+	 * The control signals are active low.
+	 */
+	if (!(status & AT91_US_DCD))
+		ret |= TIOCM_CD;
+	if (!(status & AT91_US_CTS))
+		ret |= TIOCM_CTS;
+	if (!(status & AT91_US_DSR))
+		ret |= TIOCM_DSR;
+	if (!(status & AT91_US_RI))
+		ret |= TIOCM_RI;
+
+	return ret;
+}
+
+/*
+ * Stop transmitting.
+ */
+static void at91_stop_tx(struct uart_port *port)
+{
+	UART_PUT_IDR(port, AT91_US_TXRDY);
+	port->read_status_mask &= ~AT91_US_TXRDY;
+}
+
+/*
+ * Start transmitting.
+ */
+static void at91_start_tx(struct uart_port *port)
+{
+	port->read_status_mask |= AT91_US_TXRDY;
+	UART_PUT_IER(port, AT91_US_TXRDY);
+}
+
+/*
+ * Stop receiving - port is in process of being closed.
+ */
+static void at91_stop_rx(struct uart_port *port)
+{
+	UART_PUT_IDR(port, AT91_US_RXRDY);
+}
+
+/*
+ * Enable modem status interrupts
+ */
+static void at91_enable_ms(struct uart_port *port)
+{
+	port->read_status_mask |= (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC);
+	UART_PUT_IER(port, AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC);
+}
+
+/*
+ * Control the transmission of a break signal
+ */
+static void at91_break_ctl(struct uart_port *port, int break_state)
+{
+	if (break_state != 0)
+		UART_PUT_CR(port, AT91_US_STTBRK);	/* start break */
+	else
+		UART_PUT_CR(port, AT91_US_STPBRK);	/* stop break */
+}
+
+/*
+ * Characters received (called from interrupt handler)
+ */
+static void at91_rx_chars(struct uart_port *port, struct pt_regs *regs)
+{
+	struct tty_struct *tty = port->info->tty;
+	unsigned int status, ch, flg;
+
+	status = UART_GET_CSR(port) & port->read_status_mask;
+	while (status & (AT91_US_RXRDY)) {
+		ch = UART_GET_CHAR(port);
+
+		if (tty->flip.count >= TTY_FLIPBUF_SIZE)
+			goto ignore_char;
+		port->icount.rx++;
+
+		flg = TTY_NORMAL;
+
+		/*
+		 * note that the error handling code is
+		 * out of the main execution path
+		 */
+		if (unlikely(status & (AT91_US_PARE | AT91_US_FRAME | AT91_US_OVRE))) {
+			UART_PUT_CR(port, AT91_US_RSTSTA);	/* clear error */
+			if (status & (AT91_US_PARE))
+				port->icount.parity++;
+			if (status & (AT91_US_FRAME))
+				port->icount.frame++;
+			if (status & (AT91_US_OVRE))
+				port->icount.overrun++;
+
+			if (status & AT91_US_PARE)
+				flg = TTY_PARITY;
+			else if (status & AT91_US_FRAME)
+				flg = TTY_FRAME;
+			if (status & AT91_US_OVRE) {
+				/*
+				 * overrun does *not* affect the character
+				 * we read from the FIFO
+				 */
+				tty_insert_flip_char(tty, ch, flg);
+				ch = 0;
+				flg = TTY_OVERRUN;
+			}
+#ifdef SUPPORT_SYSRQ
+			port->sysrq = 0;
+#endif
+		}
+
+		if (uart_handle_sysrq_char(port, ch, regs))
+			goto ignore_char;
+
+		tty_insert_flip_char(tty, ch, flg);
+
+	ignore_char:
+		status = UART_GET_CSR(port) & port->read_status_mask;
+	}
+
+	tty_flip_buffer_push(tty);
+}
+
+/*
+ * Transmit characters (called from interrupt handler)
+ */
+static void at91_tx_chars(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->info->xmit;
+
+	if (port->x_char) {
+		UART_PUT_CHAR(port, port->x_char);
+		port->icount.tx++;
+		port->x_char = 0;
+		return;
+	}
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+		at91_stop_tx(port);
+		return;
+	}
+
+	while (UART_GET_CSR(port) & AT91_US_TXRDY) {
+		UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+		if (uart_circ_empty(xmit))
+			break;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		at91_stop_tx(port);
+}
+
+/*
+ * Interrupt handler
+ */
+static irqreturn_t at91_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	struct uart_port *port = dev_id;
+	unsigned int status, pending, pass_counter = 0;
+
+	status = UART_GET_CSR(port);
+	pending = status & port->read_status_mask;
+	if (pending) {
+		do {
+			if (pending & AT91_US_RXRDY)
+				at91_rx_chars(port, regs);
+
+			/* Clear the relevent break bits */
+			if (pending & AT91_US_RXBRK) {
+				UART_PUT_CR(port, AT91_US_RSTSTA);
+				port->icount.brk++;
+				uart_handle_break(port);
+			}
+
+			// TODO: All reads to CSR will clear these interrupts!
+			if (pending & AT91_US_RIIC) port->icount.rng++;
+			if (pending & AT91_US_DSRIC) port->icount.dsr++;
+			if (pending & AT91_US_DCDIC)
+				uart_handle_dcd_change(port, !(status & AT91_US_DCD));
+			if (pending & AT91_US_CTSIC)
+				uart_handle_cts_change(port, !(status & AT91_US_CTS));
+			if (pending & (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC))
+				wake_up_interruptible(&port->info->delta_msr_wait);
+
+			if (pending & AT91_US_TXRDY)
+				at91_tx_chars(port);
+			if (pass_counter++ > AT91_ISR_PASS_LIMIT)
+				break;
+
+			status = UART_GET_CSR(port);
+			pending = status & port->read_status_mask;
+		} while (pending);
+	}
+	return IRQ_HANDLED;
+}
+
+/*
+ * Perform initialization and enable port for reception
+ */
+static int at91_startup(struct uart_port *port)
+{
+	int retval;
+
+	/*
+	 * Ensure that no interrupts are enabled otherwise when
+	 * request_irq() is called we could get stuck trying to
+	 * handle an unexpected interrupt
+	 */
+	UART_PUT_IDR(port, -1);
+
+	/*
+	 * Allocate the IRQ
+	 */
+	retval = request_irq(port->irq, at91_interrupt, SA_SHIRQ, "at91_serial", port);
+	if (retval) {
+		printk("at91_serial: at91_startup - Can't get irq\n");
+		return retval;
+	}
+
+	/*
+	 * If there is a specific "open" function (to register
+	 * control line interrupts)
+	 */
+	if (at91_open) {
+		retval = at91_open(port);
+		if (retval) {
+			free_irq(port->irq, port);
+			return retval;
+		}
+	}
+
+	port->read_status_mask = AT91_US_RXRDY | AT91_US_TXRDY | AT91_US_OVRE
+			| AT91_US_FRAME | AT91_US_PARE | AT91_US_RXBRK;
+	/*
+	 * Finally, enable the serial port
+	 */
+	UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
+	UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN);		/* enable xmit & rcvr */
+	UART_PUT_IER(port, AT91_US_RXRDY);			/* do receive only */
+	return 0;
+}
+
+/*
+ * Disable the port
+ */
+static void at91_shutdown(struct uart_port *port)
+{
+	/*
+	 * Disable all interrupts, port and break condition.
+	 */
+	UART_PUT_CR(port, AT91_US_RSTSTA);
+	UART_PUT_IDR(port, -1);
+
+	/*
+	 * Free the interrupt
+	 */
+	free_irq(port->irq, port);
+
+	/*
+	 * If there is a specific "close" function (to unregister
+	 * control line interrupts)
+	 */
+	if (at91_close)
+		at91_close(port);
+}
+
+/*
+ * Power / Clock management.
+ */
+static void at91_serial_pm(struct uart_port *port, unsigned int state, unsigned int oldstate)
+{
+	switch (state) {
+		case 0:
+			/*
+			 * Enable the peripheral clock for this serial port.
+			 * This is called on uart_open() or a resume event.
+			 */
+			at91_sys_write(AT91_PMC_PCER, 1 << port->irq);
+			break;
+		case 3:
+			/*
+			 * Disable the peripheral clock for this serial port.
+			 * This is called on uart_close() or a suspend event.
+			 */
+			if (port->irq != AT91_ID_SYS)			/* is this a shared clock? */
+				at91_sys_write(AT91_PMC_PCDR, 1 << port->irq);
+			break;
+		default:
+			printk(KERN_ERR "at91_serial: unknown pm %d\n", state);
+	}
+}
+
+/*
+ * Change the port parameters
+ */
+static void at91_set_termios(struct uart_port *port, struct termios * termios, struct termios * old)
+{
+	unsigned long flags;
+	unsigned int mode, imr, quot, baud;
+
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+	quot = uart_get_divisor(port, baud);
+
+	/* Get current mode register */
+	mode = UART_GET_MR(port) & ~(AT91_US_CHRL | AT91_US_NBSTOP | AT91_US_PAR);
+
+	/* byte size */
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		mode |= AT91_US_CHRL_5;
+		break;
+	case CS6:
+		mode |= AT91_US_CHRL_6;
+		break;
+	case CS7:
+		mode |= AT91_US_CHRL_7;
+		break;
+	default:
+		mode |= AT91_US_CHRL_8;
+		break;
+	}
+
+	/* stop bits */
+	if (termios->c_cflag & CSTOPB)
+		mode |= AT91_US_NBSTOP_2;
+
+	/* parity */
+	if (termios->c_cflag & PARENB) {
+		if (termios->c_cflag & CMSPAR) {			/* Mark or Space parity */
+			if (termios->c_cflag & PARODD)
+				mode |= AT91_US_PAR_MARK;
+			else
+				mode |= AT91_US_PAR_SPACE;
+		}
+		else if (termios->c_cflag & PARODD)
+			mode |= AT91_US_PAR_ODD;
+		else
+			mode |= AT91_US_PAR_EVEN;
+	}
+	else
+		mode |= AT91_US_PAR_NONE;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	port->read_status_mask |= AT91_US_OVRE;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= AT91_US_FRAME | AT91_US_PARE;
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		port->read_status_mask |= AT91_US_RXBRK;
+
+	/*
+	 * Characters to ignore
+	 */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask |= (AT91_US_FRAME | AT91_US_PARE);
+	if (termios->c_iflag & IGNBRK) {
+		port->ignore_status_mask |= AT91_US_RXBRK;
+		/*
+		 * If we're ignoring parity and break indicators,
+		 * ignore overruns too (for real raw support).
+		 */
+		if (termios->c_iflag & IGNPAR)
+			port->ignore_status_mask |= AT91_US_OVRE;
+	}
+
+	// TODO: Ignore all characters if CREAD is set.
+
+	/* update the per-port timeout */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	/* disable interrupts and drain transmitter */
+	imr = UART_GET_IMR(port);	/* get interrupt mask */
+	UART_PUT_IDR(port, -1);		/* disable all interrupts */
+	while (!(UART_GET_CSR(port) & AT91_US_TXEMPTY)) { barrier(); }
+
+	/* disable receiver and transmitter */
+	UART_PUT_CR(port, AT91_US_TXDIS | AT91_US_RXDIS);
+
+	/* set the parity, stop bits and data size */
+	UART_PUT_MR(port, mode);
+
+	/* set the baud rate */
+	UART_PUT_BRGR(port, quot);
+	UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
+	UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN);
+
+	/* restore interrupts */
+	UART_PUT_IER(port, imr);
+
+	/* CTS flow-control and modem-status interrupts */
+	if (UART_ENABLE_MS(port, termios->c_cflag))
+		port->ops->enable_ms(port);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/*
+ * Return string describing the specified port
+ */
+static const char *at91_type(struct uart_port *port)
+{
+	return (port->type == PORT_AT91RM9200) ? "AT91_SERIAL" : NULL;
+}
+
+/*
+ * Release the memory region(s) being used by 'port'.
+ */
+static void at91_release_port(struct uart_port *port)
+{
+	release_mem_region(port->mapbase,
+		(port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K);
+}
+
+/*
+ * Request the memory region(s) being used by 'port'.
+ */
+static int at91_request_port(struct uart_port *port)
+{
+	return request_mem_region(port->mapbase,
+		(port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K,
+		"at91_serial") != NULL ? 0 : -EBUSY;
+
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void at91_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE) {
+		port->type = PORT_AT91RM9200;
+		at91_request_port(port);
+	}
+}
+
+/*
+ * Verify the new serial_struct (for TIOCSSERIAL).
+ */
+static int at91_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	int ret = 0;
+	if (ser->type != PORT_UNKNOWN && ser->type != PORT_AT91RM9200)
+		ret = -EINVAL;
+	if (port->irq != ser->irq)
+		ret = -EINVAL;
+	if (ser->io_type != SERIAL_IO_MEM)
+		ret = -EINVAL;
+	if (port->uartclk / 16 != ser->baud_base)
+		ret = -EINVAL;
+	if ((void *)port->mapbase != ser->iomem_base)
+		ret = -EINVAL;
+	if (port->iobase != ser->port)
+		ret = -EINVAL;
+	if (ser->hub6 != 0)
+		ret = -EINVAL;
+	return ret;
+}
+
+static struct uart_ops at91_pops = {
+	.tx_empty	= at91_tx_empty,
+	.set_mctrl	= at91_set_mctrl,
+	.get_mctrl	= at91_get_mctrl,
+	.stop_tx	= at91_stop_tx,
+	.start_tx	= at91_start_tx,
+	.stop_rx	= at91_stop_rx,
+	.enable_ms	= at91_enable_ms,
+	.break_ctl	= at91_break_ctl,
+	.startup	= at91_startup,
+	.shutdown	= at91_shutdown,
+	.set_termios	= at91_set_termios,
+	.type		= at91_type,
+	.release_port	= at91_release_port,
+	.request_port	= at91_request_port,
+	.config_port 	= at91_config_port,
+	.verify_port 	= at91_verify_port,
+	.pm		= at91_serial_pm,
+};
+
+static struct uart_port at91_ports[AT91_NR_UART];
+
+void __init at91_init_ports(void)
+{
+	static int first = 1;
+	int i;
+
+	if (!first)
+		return;
+	first = 0;
+
+	for (i = 0; i < AT91_NR_UART; i++) {
+		at91_ports[i].iotype	= UPIO_MEM;
+		at91_ports[i].flags     = UPF_BOOT_AUTOCONF;
+		at91_ports[i].uartclk   = at91_master_clock;
+		at91_ports[i].ops	= &at91_pops;
+		at91_ports[i].fifosize  = 1;
+		at91_ports[i].line	= i;
+ 	}
+}
+
+void __init at91_register_uart_fns(struct at91rm9200_port_fns *fns)
+{
+	if (fns->enable_ms)
+		at91_pops.enable_ms = fns->enable_ms;
+	if (fns->get_mctrl)
+		at91_pops.get_mctrl = fns->get_mctrl;
+	if (fns->set_mctrl)
+		at91_pops.set_mctrl = fns->set_mctrl;
+	at91_open          = fns->open;
+	at91_close         = fns->close;
+	at91_pops.pm       = fns->pm;
+	at91_pops.set_wake = fns->set_wake;
+}
+
+/*
+ * Setup ports.
+ */
+void __init at91_register_uart(int idx, int port)
+{
+	if ((idx < 0) || (idx >= AT91_NR_UART)) {
+		printk(KERN_ERR "%s: bad index number %d\n", __FUNCTION__, idx);
+		return;
+	}
+
+	switch (port) {
+	case 0:
+		at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US0;
+		at91_ports[idx].mapbase = AT91_VA_BASE_US0;
+		at91_ports[idx].irq     = AT91_ID_US0;
+		AT91_CfgPIO_USART0();
+		break;
+	case 1:
+		at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US1;
+		at91_ports[idx].mapbase = AT91_VA_BASE_US1;
+		at91_ports[idx].irq     = AT91_ID_US1;
+		AT91_CfgPIO_USART1();
+		break;
+	case 2:
+		at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US2;
+		at91_ports[idx].mapbase = AT91_VA_BASE_US2;
+		at91_ports[idx].irq     = AT91_ID_US2;
+		AT91_CfgPIO_USART2();
+		break;
+	case 3:
+		at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US3;
+		at91_ports[idx].mapbase = AT91_VA_BASE_US3;
+		at91_ports[idx].irq     = AT91_ID_US3;
+		AT91_CfgPIO_USART3();
+		break;
+	case 4:
+		at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_DBGU;
+		at91_ports[idx].mapbase = AT91_VA_BASE_DBGU;
+		at91_ports[idx].irq     = AT91_ID_SYS;
+		AT91_CfgPIO_DBGU();
+		break;
+	default:
+		printk(KERN_ERR  "%s : bad port number %d\n", __FUNCTION__, port);
+	}
+}
+
+#ifdef CONFIG_SERIAL_AT91_CONSOLE
+
+/*
+ * Interrupts are disabled on entering
+ */
+static void at91_console_write(struct console *co, const char *s, u_int count)
+{
+	struct uart_port *port = at91_ports + co->index;
+	unsigned int status, i, imr;
+
+	/*
+	 *	First, save IMR and then disable interrupts
+	 */
+	imr = UART_GET_IMR(port);	/* get interrupt mask */
+	UART_PUT_IDR(port, AT91_US_RXRDY | AT91_US_TXRDY);
+
+	/*
+	 *	Now, do each character
+	 */
+	for (i = 0; i < count; i++) {
+		do {
+			status = UART_GET_CSR(port);
+		} while (!(status & AT91_US_TXRDY));
+		UART_PUT_CHAR(port, s[i]);
+		if (s[i] == '\n') {
+			do {
+				status = UART_GET_CSR(port);
+			} while (!(status & AT91_US_TXRDY));
+			UART_PUT_CHAR(port, '\r');
+		}
+	}
+
+	/*
+	 *	Finally, wait for transmitter to become empty
+	 *	and restore IMR
+	 */
+	do {
+		status = UART_GET_CSR(port);
+	} while (!(status & AT91_US_TXRDY));
+	UART_PUT_IER(port, imr);	/* set interrupts back the way they were */
+}
+
+/*
+ * If the port was already initialised (eg, by a boot loader), try to determine
+ * the current setup.
+ */
+static void __init at91_console_get_options(struct uart_port *port, int *baud, int *parity, int *bits)
+{
+	unsigned int mr, quot;
+
+// TODO: CR is a write-only register
+//	unsigned int cr;
+//
+//	cr = UART_GET_CR(port) & (AT91_US_RXEN | AT91_US_TXEN);
+//	if (cr == (AT91_US_RXEN | AT91_US_TXEN)) {
+//		/* ok, the port was enabled */
+//	}
+
+	mr = UART_GET_MR(port) & AT91_US_CHRL;
+	if (mr == AT91_US_CHRL_8)
+		*bits = 8;
+	else
+		*bits = 7;
+
+	mr = UART_GET_MR(port) & AT91_US_PAR;
+	if (mr == AT91_US_PAR_EVEN)
+		*parity = 'e';
+	else if (mr == AT91_US_PAR_ODD)
+		*parity = 'o';
+
+	quot = UART_GET_BRGR(port);
+	*baud = port->uartclk / (16 * (quot));
+}
+
+static int __init at91_console_setup(struct console *co, char *options)
+{
+	struct uart_port *port;
+	int baud = 115200;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	/*
+	 * Check whether an invalid uart number has been specified, and
+	 * if so, search for the first available port that does have
+	 * console support.
+	 */
+	port = uart_get_console(at91_ports, AT91_NR_UART, co);
+
+	/*
+	 * Enable the serial console, in-case bootloader did not do it.
+	 */
+	at91_sys_write(AT91_PMC_PCER, 1 << port->irq);	/* enable clock */
+	UART_PUT_IDR(port, -1);				/* disable interrupts */
+	UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
+	UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN);
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+	else
+		at91_console_get_options(port, &baud, &parity, &bits);
+
+	return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver at91_uart;
+
+static struct console at91_console = {
+	.name		= AT91_DEVICENAME,
+	.write		= at91_console_write,
+	.device		= uart_console_device,
+	.setup		= at91_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &at91_uart,
+};
+
+#define AT91_CONSOLE_DEVICE	&at91_console
+
+static int  __init at91_console_init(void)
+{
+	at91_init_ports();
+
+	at91_console.index = at91_console_port;
+	register_console(&at91_console);
+	return 0;
+}
+console_initcall(at91_console_init);
+
+#else
+#define AT91_CONSOLE_DEVICE	NULL
+#endif
+
+static struct uart_driver at91_uart = {
+	.owner			= THIS_MODULE,
+	.driver_name		= AT91_DEVICENAME,
+	.dev_name		= AT91_DEVICENAME,
+	.devfs_name		= AT91_DEVICENAME,
+	.major			= SERIAL_AT91_MAJOR,
+	.minor			= MINOR_START,
+	.nr			= AT91_NR_UART,
+	.cons			= AT91_CONSOLE_DEVICE,
+};
+
+static int __init at91_serial_init(void)
+{
+	int ret, i;
+
+	at91_init_ports();
+
+	ret = uart_register_driver(&at91_uart);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < AT91_NR_UART; i++) {
+		if (at91_serial_map[i] >= 0)
+			uart_add_one_port(&at91_uart, &at91_ports[i]);
+	}
+
+	return 0;
+}
+
+static void __exit at91_serial_exit(void)
+{
+	int i;
+
+	for (i = 0; i < AT91_NR_UART; i++) {
+ 		if (at91_serial_map[i] >= 0)
+			uart_remove_one_port(&at91_uart, &at91_ports[i]);
+  	}
+
+	uart_unregister_driver(&at91_uart);
+}
+
+module_init(at91_serial_init);
+module_exit(at91_serial_exit);
+
+MODULE_AUTHOR("Rick Bronson");
+MODULE_DESCRIPTION("AT91 generic serial port driver");
+MODULE_LICENSE("GPL");

include/asm-arm/arch-at91rm9200/at91rm9200_pdc.h

+/*
+ * include/asm-arm/arch-at91rm9200/at91rm9200_pdc.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Peripheral Data Controller (PDC) registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91RM9200_PDC_H
+#define AT91RM9200_PDC_H
+
+#define AT91_PDC_RPR		0x100	/* Receive Pointer Register */
+#define AT91_PDC_RCR		0x104	/* Receive Counter Register */
+#define AT91_PDC_TPR		0x108	/* Transmit Pointer Register */
+#define AT91_PDC_TCR		0x10c	/* Transmit Counter Register */
+#define AT91_PDC_RNPR		0x110	/* Receive Next Pointer Register */
+#define AT91_PDC_RNCR		0x114	/* Receive Next Counter Register */
+#define AT91_PDC_TNPR		0x118	/* Transmit Next Pointer Register */
+#define AT91_PDC_TNCR		0x11c	/* Transmit Next Counter Register */
+
+#define AT91_PDC_PTCR		0x120	/* Transfer Control Register */
+#define		AT91_PDC_RXTEN		(1 << 0)	/* Receiver Transfer Enable */
+#define		AT91_PDC_RXTDIS		(1 << 1)	/* Receiver Transfer Disable */
+#define		AT91_PDC_TXTEN		(1 << 8)	/* Transmitter Transfer Enable */
+#define		AT91_PDC_TXTDIS		(1 << 9)	/* Transmitter Transfer Disable */
+
+#define AT91_PDC_PTSR		0x124	/* Transfer Status Register */
+
+#endif

include/asm-arm/arch-at91rm9200/at91rm9200_usart.h

+/*
+ * include/asm-arm/arch-at91rm9200/at91rm9200_usart.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * USART registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91RM9200_USART_H
+#define AT91RM9200_USART_H
+
+#define AT91_US_CR		0x00			/* Control Register */
+#define		AT91_US_RSTRX		(1 <<  2)		/* Reset Receiver */
+#define		AT91_US_RSTTX		(1 <<  3)		/* Reset Transmitter */
+#define		AT91_US_RXEN		(1 <<  4)		/* Receiver Enable */
+#define		AT91_US_RXDIS		(1 <<  5)		/* Receiver Disable */
+#define		AT91_US_TXEN		(1 <<  6)		/* Transmitter Enable */
+#define		AT91_US_TXDIS		(1 <<  7)		/* Transmitter Disable */
+#define		AT91_US_RSTSTA		(1 <<  8)		/* Reset Status Bits */
+#define		AT91_US_STTBRK		(1 <<  9)		/* Start Break */
+#define		AT91_US_STPBRK		(1 << 10)		/* Stop Break */
+#define		AT91_US_STTTO		(1 << 11)		/* Start Time-out */
+#define		AT91_US_SENDA		(1 << 12)		/* Send Address */
+#define		AT91_US_RSTIT		(1 << 13)		/* Reset Iterations */
+#define		AT91_US_RSTNACK		(1 << 14)		/* Reset Non Acknowledge */
+#define		AT91_US_RETTO		(1 << 15)		/* Rearm Time-out */
+#define		AT91_US_DTREN		(1 << 16)		/* Data Terminal Ready Enable */
+#define		AT91_US_DTRDIS		(1 << 17)		/* Data Terminal Ready Disable */
+#define		AT91_US_RTSEN		(1 << 18)		/* Request To Send Enable */
+#define		AT91_US_RTSDIS		(1 << 19)		/* Request To Send Disable */
+
+#define AT91_US_MR		0x04			/* Mode Register */
+#define		AT91_US_USMODE		(0xf <<  0)		/* Mode of the USART */
+#define			AT91_US_USMODE_NORMAL		0
+#define			AT91_US_USMODE_RS485		1
+#define			AT91_US_USMODE_HWHS		2
+#define			AT91_US_USMODE_MODEM		3
+#define			AT91_US_USMODE_ISO7816_T0	4
+#define			AT91_US_USMODE_ISO7816_T1	6
+#define			AT91_US_USMODE_IRDA		8
+#define		AT91_US_USCLKS		(3   <<  4)		/* Clock Selection */
+#define		AT91_US_CHRL		(3   <<  6)		/* Character Length */
+#define			AT91_US_CHRL_5			(0 <<  6)
+#define			AT91_US_CHRL_6			(1 <<  6)
+#define			AT91_US_CHRL_7			(2 <<  6)
+#define			AT91_US_CHRL_8			(3 <<  6)
+#define		AT91_US_SYNC		(1 <<  8)		/* Synchronous Mode Select */
+#define		AT91_US_PAR		(7 <<  9)		/* Parity Type */
+#define			AT91_US_PAR_EVEN		(0 <<  9)
+#define			AT91_US_PAR_ODD			(1 <<  9)
+#define			AT91_US_PAR_SPACE		(2 <<  9)
+#define			AT91_US_PAR_MARK		(3 <<  9)
+#define			AT91_US_PAR_NONE		(4 <<  9)
+#define			AT91_US_PAR_MULTI_DROP		(6 <<  9)
+#define		AT91_US_NBSTOP		(3 << 12)		/* Number of Stop Bits */
+#define			AT91_US_NBSTOP_1		(0 << 12)
+#define			AT91_US_NBSTOP_1_5		(1 << 12)
+#define			AT91_US_NBSTOP_2		(2 << 12)
+#define		AT91_US_CHMODE		(3 << 14)		/* Channel Mode */
+#define			AT91_US_CHMODE_NORMAL		(0 << 14)
+#define			AT91_US_CHMODE_ECHO		(1 << 14)
+#define			AT91_US_CHMODE_LOC_LOOP		(2 << 14)
+#define			AT91_US_CHMODE_REM_LOOP		(3 << 14)
+#define		AT91_US_MSBF		(1 << 16)		/* Bit Order */
+#define		AT91_US_MODE9		(1 << 17)		/* 9-bit Character Length */
+#define		AT91_US_CLKO		(1 << 18)		/* Clock Output Select */
+#define		AT91_US_OVER		(1 << 19)		/* Oversampling Mode */
+#define		AT91_US_INACK		(1 << 20)		/* Inhibit Non Acknowledge */
+#define		AT91_US_DSNACK		(1 << 21)		/* Disable Successive NACK */
+#define		AT91_US_MAX_ITER	(7 << 24)		/* Max Iterations */
+#define		AT91_US_FILTER		(1 << 28)		/* Infrared Receive Line Filter */
+
+#define AT91_US_IER		0x08			/* Interrupt Enable Register */
+#define		AT91_US_RXRDY		(1 <<  0)		/* Receiver Ready */
+#define		AT91_US_TXRDY		(1 <<  1)		/* Transmitter Ready */
+#define		AT91_US_RXBRK		(1 <<  2)		/* Break Received / End of Break */
+#define		AT91_US_ENDRX		(1 <<  3)		/* End of Receiver Transfer */
+#define		AT91_US_ENDTX		(1 <<  4)		/* End of Transmitter Transfer */
+#define		AT91_US_OVRE		(1 <<  5)		/* Overrun Error */
+#define		AT91_US_FRAME		(1 <<  6)		/* Framing Error */
+#define		AT91_US_PARE		(1 <<  7)		/* Parity Error */
+#define		AT91_US_TIMEOUT		(1 <<  8)		/* Receiver Time-out */
+#define		AT91_US_TXEMPTY		(1 <<  9)		/* Transmitter Empty */
+#define		AT91_US_ITERATION	(1 << 10)		/* Max number of Repetitions Reached */
+#define		AT91_US_TXBUFE		(1 << 11)		/* Transmission Buffer Empty */
+#define		AT91_US_RXBUFF		(1 << 12)		/* Reception Buffer Full */
+#define		AT91_US_NACK		(1 << 13)		/* Non Acknowledge */
+#define		AT91_US_RIIC		(1 << 16)		/* Ring Indicator Input Change */
+#define		AT91_US_DSRIC		(1 << 17)		/* Data Set Ready Input Change */
+#define		AT91_US_DCDIC		(1 << 18)		/* Data Carrier Detect Input Change */
+#define		AT91_US_CTSIC		(1 << 19)		/* Clear to Send Input Change */
+#define		AT91_US_RI		(1 << 20)		/* RI */
+#define		AT91_US_DSR		(1 << 21)		/* DSR */
+#define		AT91_US_DCD		(1 << 22)		/* DCD */
+#define		AT91_US_CTS		(1 << 23)		/* CTS */
+
+#define AT91_US_IDR		0x0c			/* Interrupt Disable Register */
+#define AT91_US_IMR		0x10			/* Interrupt Mask Register */
+#define AT91_US_CSR		0x14			/* Channel Status Register */
+#define AT91_US_RHR		0x18			/* Receiver Holding Register */
+#define AT91_US_THR		0x1c			/* Transmitter Holding Register */
+
+#define AT91_US_BRGR		0x20			/* Baud Rate Generator Register */
+#define		AT91_US_CD		(0xffff << 0)		/* Clock Divider */
+
+#define AT91_US_RTOR		0x24			/* Receiver Time-out Register */
+#define		AT91_US_TO		(0xffff << 0)		/* Time-out Value */
+
+#define AT91_US_TTGR		0x28			/* Transmitter Timeguard Register */
+#define		AT91_US_TG		(0xff << 0)		/* Timeguard Value */
+
+#define AT91_US_FIDI		0x40			/* FI DI Ratio Register */
+#define AT91_US_NER		0x44			/* Number of Errors Register */
+#define AT91_US_IF		0x4c			/* IrDA Filter Register */
+
+#endif

include/asm-arm/mach/serial_at91rm9200.h

+/*
+ *  linux/include/asm-arm/mach/serial_at91rm9200.h
+ *
+ *  Based on serial_sa1100.h  by Nicolas Pitre
+ *
+ *  Copyright (C) 2002 ATMEL Rousset
+ *
+ *  Low level machine dependent UART functions.
+ */
+#include <linux/config.h>
+
+struct uart_port;
+
+/*
+ * This is a temporary structure for registering these
+ * functions; it is intended to be discarded after boot.
+ */
+struct at91rm9200_port_fns {
+	void	(*set_mctrl)(struct uart_port *, u_int);
+	u_int	(*get_mctrl)(struct uart_port *);
+	void	(*enable_ms)(struct uart_port *);
+	void	(*pm)(struct uart_port *, u_int, u_int);
+	int	(*set_wake)(struct uart_port *, u_int);
+	int	(*open)(struct uart_port *);
+	void	(*close)(struct uart_port *);
+};
+
+#if defined(CONFIG_SERIAL_AT91)
+void at91_register_uart_fns(struct at91rm9200_port_fns *fns);
+void at91_register_uart(int idx, int port);
+#else
+#define at91_register_uart_fns(fns) do { } while (0)
+#define at91_register_uart(idx,port) do { } while (0)
+#endif
+
+

include/linux/serial_core.h

@@ -67,6 +67,9 @@
 /* Parisc type numbers. */
 #define PORT_MUX	48
 
+/* Atmel AT91RM9200 SoC */
+#define PORT_AT91RM9200 49
+
 /* Macintosh Zilog type numbers */
 #define PORT_MAC_ZILOG	50	/* m68k : not yet implemented */
 #define PORT_PMAC_ZILOG	51