提交 1dd6c077 编写于 作者: M Mark Brown

Merge branch 'for-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-3.2

......@@ -6122,7 +6122,7 @@ F: sound/
SOUND - SOC LAYER / DYNAMIC AUDIO POWER MANAGEMENT (ASoC)
M: Liam Girdwood <lrg@ti.com>
M: Mark Brown <broonie@opensource.wolfsonmicro.com>
T: git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6.git
T: git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
L: alsa-devel@alsa-project.org (moderated for non-subscribers)
W: http://alsa-project.org/main/index.php/ASoC
S: Supported
......
......@@ -1962,6 +1962,21 @@
#define WM8958_MICB2_DISCH_SHIFT 0 /* MICB2_DISCH */
#define WM8958_MICB2_DISCH_WIDTH 1 /* MICB2_DISCH */
/*
* R210 (0xD2) - Mic Detect 3
*/
#define WM8958_MICD_LVL_MASK 0x07FC /* MICD_LVL - [10:2] */
#define WM8958_MICD_LVL_SHIFT 2 /* MICD_LVL - [10:2] */
#define WM8958_MICD_LVL_WIDTH 9 /* MICD_LVL - [10:2] */
#define WM8958_MICD_VALID 0x0002 /* MICD_VALID */
#define WM8958_MICD_VALID_MASK 0x0002 /* MICD_VALID */
#define WM8958_MICD_VALID_SHIFT 1 /* MICD_VALID */
#define WM8958_MICD_VALID_WIDTH 1 /* MICD_VALID */
#define WM8958_MICD_STS 0x0001 /* MICD_STS */
#define WM8958_MICD_STS_MASK 0x0001 /* MICD_STS */
#define WM8958_MICD_STS_SHIFT 0 /* MICD_STS */
#define WM8958_MICD_STS_WIDTH 1 /* MICD_STS */
/*
* R76 (0x4C) - Charge Pump (1)
*/
......
......@@ -56,7 +56,7 @@ static int wm8994_retune_mobile_base[] = {
static int wm8994_readable(struct snd_soc_codec *codec, unsigned int reg)
{
struct wm8994_priv *wm8994 = snd_soc_codec_get_drvdata(codec);
struct wm8994 *control = wm8994->control_data;
struct wm8994 *control = codec->control_data;
switch (reg) {
case WM8994_GPIO_1:
......@@ -3030,11 +3030,17 @@ static irqreturn_t wm8958_mic_irq(int irq, void *data)
{
struct wm8994_priv *wm8994 = data;
struct snd_soc_codec *codec = wm8994->codec;
int reg;
int reg, count;
/* We may occasionally read a detection without an impedence
* range being provided - if that happens loop again.
*/
count = 10;
do {
reg = snd_soc_read(codec, WM8958_MIC_DETECT_3);
if (reg < 0) {
dev_err(codec->dev, "Failed to read mic detect status: %d\n",
dev_err(codec->dev,
"Failed to read mic detect status: %d\n",
reg);
return IRQ_NONE;
}
......@@ -3044,6 +3050,15 @@ static irqreturn_t wm8958_mic_irq(int irq, void *data)
goto out;
}
if (!(reg & WM8958_MICD_STS) || (reg & WM8958_MICD_LVL_MASK))
break;
msleep(1);
} while (count--);
if (count == 0)
dev_warn(codec->dev, "No impedence range reported for jack\n");
#ifndef CONFIG_SND_SOC_WM8994_MODULE
trace_snd_soc_jack_irq(dev_name(codec->dev));
#endif
......@@ -3180,9 +3195,9 @@ static int wm8994_codec_probe(struct snd_soc_codec *codec)
wm8994_request_irq(codec->control_data, WM8994_IRQ_FIFOS_ERR,
wm8994_fifo_error, "FIFO error", codec);
wm8994_request_irq(wm8994->control_data, WM8994_IRQ_TEMP_WARN,
wm8994_request_irq(codec->control_data, WM8994_IRQ_TEMP_WARN,
wm8994_temp_warn, "Thermal warning", codec);
wm8994_request_irq(wm8994->control_data, WM8994_IRQ_TEMP_SHUT,
wm8994_request_irq(codec->control_data, WM8994_IRQ_TEMP_SHUT,
wm8994_temp_shut, "Thermal shutdown", codec);
ret = wm8994_request_irq(codec->control_data, WM8994_IRQ_DCS_DONE,
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册