fa48b432 "target-ppc: Remove hack for ppc_hash64_load_hpte*() with HV KVM"
purports to remove a hack in the handling of hash page tables (HPTs)
managed by KVM instead of qemu.  However, it actually went in the wrong
direction.

That patch requires anything looking for an external HPT (that is one not
managed by the guest itself) to check both env->external_htab (for a qemu
managed HPT) and kvmppc_kern_htab (for a KVM managed HPT).  That's a
problem because kvmppc_kern_htab is local to mmu-hash64.c, but some places
which need to check for an external HPT are outside that, such as
kvm_arch_get_registers().  The latter was subtly broken by the earlier
patch such that gdbstub can no longer access memory.

Basically a KVM managed HPT is much more like a qemu managed HPT than it is
like a guest managed HPT, so the original "hack" was actually on the right
track.

This partially reverts fa48b432, so we again mark a KVM managed external HPT
by putting a special but non-NULL value in env->external_htab.  It then
goes further, using that marker to eliminate the kvmppc_kern_htab global
entirely.  The ppc_hash64_set_external_hpt() helper function is extended
to set that marker if passed a NULL value (if you're setting an external
HPT, but don't have an actual HPT to set, the assumption is that it must
be a KVM managed HPT).

This also has some flow-on changes to the HPT access helpers, required by
the above changes.
Reported-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Reviewed-by: NThomas Huth <thuth@redhat.com>
Reviewed-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Tested-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>

When a Power cpu with 64-bit hash MMU has it's hash page table (HPT)
pointer updated by a write to the SDR1 register we need to update some
derived variables.  Likewise, when the cpu is configured for an external
HPT (one not in the guest memory space) some derived variables need to be
updated.

Currently the logic for this is (partially) duplicated in ppc_store_sdr1()
and in spapr_cpu_reset().  In future we're going to need it in some other
places, so make some common helpers for this update.

In addition the new ppc_hash64_set_external_hpt() helper also updates
SDR1 in KVM - it's not updated by the normal runtime KVM <-> qemu CPU
synchronization.  In a sense this belongs logically in the
ppc_hash64_set_sdr1() helper, but that is called from
kvm_arch_get_registers() so can't itself call cpu_synchronize_state()
without infinite recursion.  In practice this doesn't matter because
the only other caller is TCG specific.

Currently there aren't situations where updating SDR1 at runtime in KVM
matters, but there are going to be in future.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Reviewed-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: NThomas Huth <thuth@redhat.com>

Currently the getting and setting of Power MMU registers (sregs) take up
large inline chunks of the kvm_arch_get_registers() and
kvm_arch_put_registers() functions.  Especially since there are two
variants (for Book-E and Book-S CPUs), only one of which will be used in
practice, this is pretty hard to read.

This patch splits these out into helper functions for clarity.  No
functional change is expected.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Reviewed-by: NThomas Huth <thuth@redhat.com>
Reviewed-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>

Since 3f1e1478, QEMU has adopted a convention of supporting function
hotplug by deferring hotplug events until func 0 is hotplugged.
This is likely how management tools like libvirt would expose
such support going forward.

Since sPAPR guests rely on per-func events rather than
slot-based, our protocol has been to hotplug func 0 *first* to
avoid cases where devices appear within guests without func 0
present to avoid undefined behavior.

To remain compatible with new convention, defer hotplug in a
similar manner, but then generate events in 0-first order as we
did in the past. Once func 0 present, fail any attempts to plug
additional functions (as we do with PCIe).

For unplug, defer unplug operations in a similar manner, but
generate unplug events such that function 0 is removed last in guest.
Signed-off-by: NMichael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

This adds a new POWER8+NVLink CPU PVR which core is identical to POWER8
but has a different PVR. The only available machine now has PVR
pvr 004c 0100 so this defines "POWER8NVL" alias as v1.0.

The corresponding kernel commit is
https://github.com/torvalds/linux/commit/ddee09c099c3
"powerpc: Add PVR for POWER8NVL processor"
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

The TAR special purpose register currently does not get migrated
under KVM because it does not get synchronized with the kernel.
Use spr_register_kvm() instead of spr_register() to fix this issue.
Signed-off-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

POWER8 / PowerISA 2.07 has a new special purpose register called PSPB
("Problem State Priority Boost Register"). The contents of this register
are currently lost during migration. To be able to migrate this register,
too, we've got to define this SPR along with the other SPRs of POWER8.
Signed-off-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

slirp: Adding IPv6 support to Qemu -net user mode

# gpg: Signature made Tue 15 Mar 2016 16:06:03 GMT using RSA key ID FB6B2F1D
# gpg: Good signature from "Samuel Thibault <samuel.thibault@gnu.org>"
# gpg:                 aka "Samuel Thibault <sthibault@debian.org>"
# gpg:                 aka "Samuel Thibault <samuel.thibault@inria.fr>"
# gpg:                 aka "Samuel Thibault <samuel.thibault@labri.fr>"
# gpg:                 aka "Samuel Thibault <samuel.thibault@ens-lyon.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg:          It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 900C B024 B679 31D4 0F82  304B D017 8C76 7D06 9EE6
#      Subkey fingerprint: F632 74CD C630 0873 CB3D  29D9 E3E5 1CE8 FB6B 2F1D

* remotes/thibault/tags/samuel-thibault:
  slirp: Add IPv6 support to the TFTP code
  qapi-schema, qemu-options & slirp: Adding Qemu options for IPv6 addresses
  slirp: Adding IPv6 address for DNS relay
  slirp: Handle IPv6 in TCP functions
  slirp: Reindent after refactoring
  slirp: Generalizing and neutralizing various TCP functions before adding IPv6 stuff
  slirp: Factorizing tcpiphdr structure with an union
  slirp: Adding IPv6 UDP support
  slirp: Adding ICMPv6 error sending
  slirp: Fix ICMP error sending
  slirp: Adding IPv6, ICMPv6 Echo and NDP autoconfiguration
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

vhost, virtio, pci, pc, acpi

nvdimm work
sparse cpu id rework
ipmi enhancements
fixes all over the place
pxb option to tweak chassis number
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

# gpg: Signature made Tue 15 Mar 2016 14:33:10 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg:                 aka "Michael S. Tsirkin <mst@redhat.com>"

* remotes/mst/tags/for_upstream: (51 commits)
  hw/acpi: fix GSI links UID
  ipmi: add some local variables in ipmi_sdr_init
  ipmi: remove the need of an ending record in the SDR table
  ipmi: use a function to initialize the SDR table
  ipmi: add a realize function to the device class
  ipmi: add rsp_buffer_set_error() helper
  ipmi: remove IPMI_CHECK_RESERVATION() macro
  ipmi: replace IPMI_ADD_RSP_DATA() macro with inline helpers
  ipmi: remove IPMI_CHECK_CMD_LEN() macro
  MAINTAINERS: machine core
  MAINTAINERS: Add an entry for virtio header files
  pc: acpi: clarify why possible LAPIC entries must be present in MADT
  pc: acpi: drop cpu->found_cpus bitmap
  pc: acpi: create Processor and Notify objects only for valid lapics
  pc: acpi: create MADT.lapic entries only for valid lapics
  pc: acpi: SRAT: create only valid processor lapic entries
  pc: acpi: cleanup qdev_get_machine() calls
  machine: introduce MachineClass.possible_cpu_arch_ids() hook
  pc: init pcms->apic_id_limit once and use it throughout pc.c
  pc: acpi: remove NOP assignment
  ...
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Add the handler code for incoming TFTP packets to udp6_input(),
and make sure that the TFTP code can send packets with both,
udp_output() and udp6_output() by introducing a wrapper function
called tftp_udp_output().
Signed-off-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>

Merge I/O fixes

# gpg: Signature made Tue 15 Mar 2016 14:42:43 GMT using RSA key ID 15104FDF
# gpg: Good signature from "Daniel P. Berrange <dan@berrange.com>"
# gpg:                 aka "Daniel P. Berrange <berrange@redhat.com>"

* remotes/berrange/tags/pull-io-next-2016-03-15-1:
  io: stronger check for support for IPv4/6
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

According to the ACPI spec, each UID must be unique.
Use the irq number as UID for GSI links.
Suggested-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMarcel Apfelbaum <marcel@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Instead of just checking for bind(), also check whether
getaddrinfo can resolve IPv6 addresses. This catches
failure when travis runs QEMU builds inside minimal
docker containers
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>

X86 fixes

# gpg: Signature made Mon 14 Mar 2016 20:26:25 GMT using RSA key ID 984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"

* remotes/ehabkost/tags/x86-pull-request:
  kvm: Remove x2apic feature from CPU model when kernel_irqchip is off
  hyperv: cpu hotplug fix with HyperV enabled
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

target-i386 fixes

# gpg: Signature made Mon 14 Mar 2016 17:54:06 GMT using RSA key ID 4DD0279B
# gpg: Good signature from "Richard Henderson <rth7680@gmail.com>"
# gpg:                 aka "Richard Henderson <rth@redhat.com>"
# gpg:                 aka "Richard Henderson <rth@twiddle.net>"

* remotes/rth/tags/pull-i386-20160314:
  target-i386: Dump unknown opcodes with -d unimp
  target-i386: Fix inhibit irq mask handling
  target-i386: Use gen_nop_modrm for prefetch instructions
  target-i386: Fix addr16 prefix
  target-i386: Fix SMSW for 64-bit mode
  target-i386: Fix SMSW and LMSW from/to register
  target-i386: Avoid repeated calls to the bnd_jmp helper
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

This patch adds parameters to manage some new options in the qemu -net
command.
Slirp IPv6 address, network prefix, and DNS IPv6 address can be given in
argument to the qemu command.
Defaults parameters are respectively fec0::2, fec0::, /64 and fec0::3.
Signed-off-by: NYann Bordenave <meow@meowstars.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

This patch adds an IPv6 address to the DNS relay. in6_equal_dns() is
developed using this Slirp attribute.
sotranslate_in/out/accept() are also updated to manage the IPv6 case so the
guest can be able to join the host using one of the Slirp addresses.

For now this only points to localhost. Further development will be needed to
automatically fetch the IPv6 address from resolv.conf, and announce this via
RDNSS.
Signed-off-by: NGuillaume Subiron <maethor@subiron.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

This patch adds IPv6 case in TCP functions refactored by the last
patches.
This also adds IPv6 pseudo-header in tcpiphdr structure.
Finally, tcp_input() is called by ip6_input().
Signed-off-by: NGuillaume Subiron <maethor@subiron.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

No code change.
Signed-off-by: NGuillaume Subiron <maethor@subiron.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

Basically, this patch adds some switch in various TCP functions to
prepare them for the IPv6 case.

To have something to "switch" in tcp_input() and tcp_respond(), a new
argument is used to give them the sa_family of the addresses they are
working on.

This patch does not include the entailed reindentation, to make proofread
easier. Reindentation is adressed in the following no-op patch.
Signed-off-by: NGuillaume Subiron <maethor@subiron.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

This patch factorizes the tcpiphdr structure to put the IPv4 fields in
an union, for addition of version 6 in further patch.
Using some macros, retrocompatibility of the existing code is assured.

This patch also fixes the SLIRP_MSIZE and margin computation in various
functions, and makes them compatible with the new tcpiphdr structure,
whose size will be bigger than sizeof(struct tcphdr) + sizeof(struct ip)
Signed-off-by: NGuillaume Subiron <maethor@subiron.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

This adds the sin6 case in the fhost and lhost unions and related macros.
It adds udp6_input() and udp6_output().
It adds the IPv6 case in sorecvfrom().
Finally, udp_input() is called by ip6_input().
Signed-off-by: NGuillaume Subiron <maethor@subiron.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

Adding icmp6_send_error to send ICMPv6 Error messages. This function is
simpler than the v4 version.
Adding some calls in various functions to send ICMP errors, when a
received packet is too big, or when its hop limit is 0.
Signed-off-by: NYann Bordenave <meow@meowstars.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

Disambiguation : icmp_error is renamed into icmp_send_error, since it
doesn't manage errors, but only sends ICMP Error messages.
Signed-off-by: NYann Bordenave <meow@meowstars.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

This patch adds the functions needed to handle IPv6 packets. ICMPv6 and
NDP headers are implemented.

Slirp is now able to send NDP Router or Neighbor Advertisement when it
receives Router or Neighbor Solicitation. Using a 64bit-sized IPv6
prefix, the guest is now able to perform stateless autoconfiguration
(SLAAC) and to compute its IPv6 address.

This patch adds an ndp_table, mainly inspired by arp_table, to keep an
NDP cache and manage network address resolution.
Slirp regularly sends NDP Neighbor Advertisement, as recommended by the
RFC, to make the guest refresh its route.

This also adds ip6_cksum() to compute ICMPv6 checksums using IPv6
pseudo-header.

Some #define ETH_* are moved upper in slirp.h to make them accessible to
other slirp/*.h
Signed-off-by: NGuillaume Subiron <maethor@subiron.org>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>

Block layer patches

# gpg: Signature made Mon 14 Mar 2016 16:36:52 GMT using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"

* remotes/kevin/tags/for-upstream: (40 commits)
  iotests: Add test for QMP event rates
  monitor: Use QEMU_CLOCK_VIRTUAL for the event queue in qtest mode
  monitor: Separate QUORUM_REPORT_BAD events according to the node name
  quorum: Fix crash in quorum_aio_cb()
  iotests: Correct 081's reference output
  block: Remove unused typedef of BlockDriverDirtyHandler
  block: Move block dirty bitmap code to separate files
  typedefs: Add BdrvDirtyBitmap
  block: Include hbitmap.h in block.h
  backup: Use Bitmap to replace "s->bitmap"
  vpc: Use BB functions in .bdrv_create()
  vmdk: Use BB functions in .bdrv_create()
  vhdx: Use BB functions in .bdrv_create()
  vdi: Use BB functions in .bdrv_create()
  sheepdog: Use BB functions in .bdrv_create()
  qed: Use BB functions in .bdrv_create()
  qcow2: Use BB functions in .bdrv_create()
  qcow: Use BB functions in .bdrv_create()
  parallels: Use BB functions in .bdrv_create()
  block: Introduce blk_set_allow_write_beyond_eof()
  ...
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

x2apic feature is in the kvm_default_props and automatically added to all
CPU models when KVM is enabled. But userspace devices don't support x2apic
which can't be enabled without the in-kernel irqchip. It will trigger
warning of "host doesn't support requested feature: CPUID.01H:ECX.x2apic
[bit 21]" when kernel_irqchip is off. This patch is to fix it via removing
x2apic feature when kernel_irqchip is off.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Acked-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NEduardo Habkost <ehabkost@redhat.com>
Signed-off-by: NEduardo Habkost <ehabkost@redhat.com>

With Hyper-V enabled CPU hotplug stops working. The CPU appears
in device manager on Windows but does not appear in peformance
monitor and control panel.

The root of the problem is the following. Windows checks
HV_X64_CPU_DYNAMIC_PARTITIONING_AVAILABLE bit in CPUID. The
presence of this bit is enough to cure the situation.

The bit should be set when CPU hotplug is allowed for HyperV VM.
The check that hot_add_cpu callback is defined is enough from the
protocol point of view. Though this callback is defined almost
always thus there is no need to export that knowledge in the
other way.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
CC: "Andreas Färber" <afaerber@suse.de>
Reviewed-by: NEduardo Habkost <ehabkost@redhat.com>
Signed-off-by: NEduardo Habkost <ehabkost@redhat.com>

We discriminate here between opcodes that are illegal in the current
cpu mode or with illegal arguments (such as modrm.mod == 3) and
encodings that are unknown (such as an unimplemented isa extension).
Signed-off-by: NRichard Henderson <rth@twiddle.net>

The patch in 7f0b7141 was too simplistic, in that we wound up setting
the flag and then resetting it immediately in gen_eob.

Fixes the reported boot problem with Windows XP.
Reported-by: NHervé Poussineau <hpoussin@reactos.org>
Tested-by: NHervé Poussineau <hpoussin@reactos.org>
Signed-off-by: NRichard Henderson <rth@twiddle.net>

Tested-by: NHervé Poussineau <hpoussin@reactos.org>
Signed-off-by: NRichard Henderson <rth@twiddle.net>

While ADDSEG will only be false in 16-bit mode for LEA, it can be
false even in other cases when 16-bit addresses are obtained via
the 67h prefix in 32-bit mode.  In this case, gen_lea_v_seg forgets
to add a nonzero FS or GS base if CS/DS/ES/SS are all zero.  This
case is pretty rare but happens when booting Windows 95/98, and
this patch fixes it.

The bug is visible since commit d6a29149, but it was introduced
together with gen_lea_v_seg and it probably could be reproduced
with a "addr16 gs movsb" instruction as early as in commit
ca2f29f5.
Reported-by: NHervé Poussineau <hpoussin@reactos.org>
Tested-by: NHervé Poussineau <hpoussin@reactos.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Message-Id: <1456931078-21635-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: NRichard Henderson <rth@twiddle.net>

In non-64-bit modes, the instruction always stores 16 bits.
But in 64-bit mode, when the destination is a register, the
instruction can write 32 or 64 bits.
Tested-by: NHervé Poussineau <hpoussin@reactos.org>
Signed-off-by: NRichard Henderson <rth@twiddle.net>

SMSW and LMSW accept register operands, but commit 1906b2af ("target-i386:
Rearrange processing of 0F 01", 2016-02-13) did not account for that.

Fixes: 1906b2afReported-by: NHervé Poussineau <hpoussin@reactos.org>
Tested-by: NHervé Poussineau <hpoussin@reactos.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Message-Id: <1456845134-18812-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: NRichard Henderson <rth@twiddle.net>

Two flags were tested the wrong way.
Tested-by: NHervé Poussineau <hpoussin@reactos.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Message-Id: <1456845145-18891-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: NRichard Henderson <rth@twiddle.net>
[rth: Fixed enable test as well.]

Block patches for pi day, v2.

# gpg: Signature made Mon Mar 14 17:35:29 2016 CET using RSA key ID E838ACAD
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>"

* mreitz/tags/pull-block-for-kevin-2016-03-14-v2:
  iotests: Add test for QMP event rates
  monitor: Use QEMU_CLOCK_VIRTUAL for the event queue in qtest mode
  monitor: Separate QUORUM_REPORT_BAD events according to the node name
  quorum: Fix crash in quorum_aio_cb()
  iotests: Correct 081's reference output
  block: Remove unused typedef of BlockDriverDirtyHandler
  block: Move block dirty bitmap code to separate files
  typedefs: Add BdrvDirtyBitmap
  block: Include hbitmap.h in block.h
  backup: Use Bitmap to replace "s->bitmap"
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

This test verifies that the rate-limited QMP events are emitted at a
maximum rate of 1 per second as defined in monitor_qapi_event_conf in
monitor.c

It also checks that QUORUM_REPORT_BAD events generated from different
nodes are kept in separate queues so they don't mask each other.
Signed-off-by: NAlberto Garcia <berto@igalia.com>
Reviewed-by: NMax Reitz <mreitz@redhat.com>
Message-id: 0dbd3ee88a59a6363042ad81cfb345037bfbf612.1457610443.git.berto@igalia.com
[mreitz@redhat.com: Renamed test from 146 to 148]
Signed-off-by: NMax Reitz <mreitz@redhat.com>

This allows us to perform tests on the monitor queues to verify that
the rate limits are enforced.
Signed-off-by: NAlberto Garcia <berto@igalia.com>
Reviewed-by: NMax Reitz <mreitz@redhat.com>
Message-id: dde511809e954a5c32d5b648bb184c03c89ed5d5.1457610443.git.berto@igalia.com
Signed-off-by: NMax Reitz <mreitz@redhat.com>

The QUORUM_REPORT_BAD event is emitted whenever there's an I/O error
in a child of a Quorum device. This event is emitted at a maximum rate
of 1 per second. This means that an error in one of the children will
mask errors in the other children if they happen within the same 1
second interval.

This patch modifies qapi_event_throttle_equal() so QUORUM_REPORT_BAD
events are kept separately if they come from different children.
Signed-off-by: NAlberto Garcia <berto@igalia.com>
Reviewed-by: NMax Reitz <mreitz@redhat.com>
Message-id: b989c0cb3755bc4b6696e796fa8ed2ef6c56606a.1457610443.git.berto@igalia.com
Reviewed-by: NEric Blake <eblake@redhat.com>
Signed-off-by: NMax Reitz <mreitz@redhat.com>