提交 31410948 编写于 作者: P Peter Maydell

hw/vexpress: Pass voltage sensor properties to sysctl device

Pass voltage sensor properties to the sysctl device. Since
these are daughterboard specific, we specify them via the
VEDBoardInfo structure.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Message-id: 1359985476-29380-9-git-send-email-peter.maydell@linaro.org
上级 8bd4824a
......@@ -154,6 +154,8 @@ struct VEDBoardInfo {
hwaddr loader_start;
const hwaddr gic_cpu_if_addr;
uint32_t proc_id;
uint32_t num_voltage_sensors;
const uint32_t *voltages;
DBoardInitFn *init;
};
......@@ -246,11 +248,25 @@ static void a9_daughterboard_init(const VEDBoardInfo *daughterboard,
sysbus_create_varargs("l2x0", 0x1e00a000, NULL);
}
/* Voltage values for SYS_CFG_VOLT daughterboard registers;
* values are in microvolts.
*/
static const uint32_t a9_voltages[] = {
1000000, /* VD10 : 1.0V : SoC internal logic voltage */
1000000, /* VD10_S2 : 1.0V : PL310, L2 cache, RAM, non-PL310 logic */
1000000, /* VD10_S3 : 1.0V : Cortex-A9, cores, MPEs, SCU, PL310 logic */
1800000, /* VCC1V8 : 1.8V : DDR2 SDRAM, test chip DDR2 I/O supply */
900000, /* DDR2VTT : 0.9V : DDR2 SDRAM VTT termination voltage */
3300000, /* VCC3V3 : 3.3V : local board supply for misc external logic */
};
static const VEDBoardInfo a9_daughterboard = {
.motherboard_map = motherboard_legacy_map,
.loader_start = 0x60000000,
.gic_cpu_if_addr = 0x1e000100,
.proc_id = 0x0c000191,
.num_voltage_sensors = ARRAY_SIZE(a9_voltages),
.voltages = a9_voltages,
.init = a9_daughterboard_init,
};
......@@ -338,11 +354,17 @@ static void a15_daughterboard_init(const VEDBoardInfo *daughterboard,
/* 0x7ffd0000: PL354 static memory controller: not modelled */
}
static const uint32_t a15_voltages[] = {
900000, /* Vcore: 0.9V : CPU core voltage */
};
static const VEDBoardInfo a15_daughterboard = {
.motherboard_map = motherboard_aseries_map,
.loader_start = 0x80000000,
.gic_cpu_if_addr = 0x2c002000,
.proc_id = 0x14000237,
.num_voltage_sensors = ARRAY_SIZE(a15_voltages),
.voltages = a15_voltages,
.init = a15_daughterboard_init,
};
......@@ -358,6 +380,7 @@ static void vexpress_common_init(const VEDBoardInfo *daughterboard,
MemoryRegion *vram = g_new(MemoryRegion, 1);
MemoryRegion *sram = g_new(MemoryRegion, 1);
const hwaddr *map = daughterboard->motherboard_map;
int i;
daughterboard->init(daughterboard, args->ram_size, args->cpu_model, pic);
......@@ -370,6 +393,13 @@ static void vexpress_common_init(const VEDBoardInfo *daughterboard,
sysctl = qdev_create(NULL, "realview_sysctl");
qdev_prop_set_uint32(sysctl, "sys_id", sys_id);
qdev_prop_set_uint32(sysctl, "proc_id", daughterboard->proc_id);
qdev_prop_set_uint32(sysctl, "len-db-voltage",
daughterboard->num_voltage_sensors);
for (i = 0; i < daughterboard->num_voltage_sensors; i++) {
char *propname = g_strdup_printf("db-voltage[%d]", i);
qdev_prop_set_uint32(sysctl, propname, daughterboard->voltages[i]);
g_free(propname);
}
qdev_init_nofail(sysctl);
sysbus_mmio_map(SYS_BUS_DEVICE(sysctl), 0, map[VE_SYSREGS]);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册