/* * OMAP3 Power Management Routines * * Copyright (C) 2006-2008 Nokia Corporation * Tony Lindgren * Jouni Hogander * * Copyright (C) 2007 Texas Instruments, Inc. * Rajendra Nayak * * Copyright (C) 2005 Texas Instruments, Inc. * Richard Woodruff * * Based on pm.c for omap1 * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "cm2xxx_3xxx.h" #include "cm-regbits-34xx.h" #include "prm-regbits-34xx.h" #include "prm2xxx_3xxx.h" #include "pm.h" #include "sdrc.h" #include "control.h" #ifdef CONFIG_SUSPEND static suspend_state_t suspend_state = PM_SUSPEND_ON; static inline bool is_suspending(void) { return (suspend_state != PM_SUSPEND_ON); } #else static inline bool is_suspending(void) { return false; } #endif /* Scratchpad offsets */ #define OMAP343X_TABLE_ADDRESS_OFFSET 0xc4 #define OMAP343X_TABLE_VALUE_OFFSET 0xc0 #define OMAP343X_CONTROL_REG_VALUE_OFFSET 0xc8 /* pm34xx errata defined in pm.h */ u16 pm34xx_errata; struct power_state { struct powerdomain *pwrdm; u32 next_state; #ifdef CONFIG_SUSPEND u32 saved_state; #endif struct list_head node; }; static LIST_HEAD(pwrst_list); static void (*_omap_sram_idle)(u32 *addr, int save_state); static int (*_omap_save_secure_sram)(u32 *addr); static struct powerdomain *mpu_pwrdm, *neon_pwrdm; static struct powerdomain *core_pwrdm, *per_pwrdm; static struct powerdomain *cam_pwrdm; static inline void omap3_per_save_context(void) { omap_gpio_save_context(); } static inline void omap3_per_restore_context(void) { omap_gpio_restore_context(); } static void omap3_enable_io_chain(void) { int timeout = 0; if (omap_rev() >= OMAP3430_REV_ES3_1) { prm_set_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD, PM_WKEN); /* Do a readback to assure write has been done */ prm_read_mod_reg(WKUP_MOD, PM_WKEN); while (!(prm_read_mod_reg(WKUP_MOD, PM_WKEN) & OMAP3430_ST_IO_CHAIN_MASK)) { timeout++; if (timeout > 1000) { printk(KERN_ERR "Wake up daisy chain " "activation failed.\n"); return; } prm_set_mod_reg_bits(OMAP3430_ST_IO_CHAIN_MASK, WKUP_MOD, PM_WKEN); } } } static void omap3_disable_io_chain(void) { if (omap_rev() >= OMAP3430_REV_ES3_1) prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD, PM_WKEN); } static void omap3_core_save_context(void) { u32 control_padconf_off; /* Save the padconf registers */ control_padconf_off = omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_OFF); control_padconf_off |= START_PADCONF_SAVE; omap_ctrl_writel(control_padconf_off, OMAP343X_CONTROL_PADCONF_OFF); /* wait for the save to complete */ while (!(omap_ctrl_readl(OMAP343X_CONTROL_GENERAL_PURPOSE_STATUS) & PADCONF_SAVE_DONE)) udelay(1); /* * Force write last pad into memory, as this can fail in some * cases according to errata 1.157, 1.185 */ omap_ctrl_writel(omap_ctrl_readl(OMAP343X_PADCONF_ETK_D14), OMAP343X_CONTROL_MEM_WKUP + 0x2a0); /* Save the Interrupt controller context */ omap_intc_save_context(); /* Save the GPMC context */ omap3_gpmc_save_context(); /* Save the system control module context, padconf already save above*/ omap3_control_save_context(); omap_dma_global_context_save(); } static void omap3_core_restore_context(void) { /* Restore the control module context, padconf restored by h/w */ omap3_control_restore_context(); /* Restore the GPMC context */ omap3_gpmc_restore_context(); /* Restore the interrupt controller context */ omap_intc_restore_context(); omap_dma_global_context_restore(); } /* * FIXME: This function should be called before entering off-mode after * OMAP3 secure services have been accessed. Currently it is only called * once during boot sequence, but this works as we are not using secure * services. */ static void omap3_save_secure_ram_context(u32 target_mpu_state) { u32 ret; if (omap_type() != OMAP2_DEVICE_TYPE_GP) { /* * MPU next state must be set to POWER_ON temporarily, * otherwise the WFI executed inside the ROM code * will hang the system. */ pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON); ret = _omap_save_secure_sram((u32 *) __pa(omap3_secure_ram_storage)); pwrdm_set_next_pwrst(mpu_pwrdm, target_mpu_state); /* Following is for error tracking, it should not happen */ if (ret) { printk(KERN_ERR "save_secure_sram() returns %08x\n", ret); while (1) ; } } } /* * PRCM Interrupt Handler Helper Function * * The purpose of this function is to clear any wake-up events latched * in the PRCM PM_WKST_x registers. It is possible that a wake-up event * may occur whilst attempting to clear a PM_WKST_x register and thus * set another bit in this register. A while loop is used to ensure * that any peripheral wake-up events occurring while attempting to * clear the PM_WKST_x are detected and cleared. */ static int prcm_clear_mod_irqs(s16 module, u8 regs) { u32 wkst, fclk, iclk, clken; u16 wkst_off = (regs == 3) ? OMAP3430ES2_PM_WKST3 : PM_WKST1; u16 fclk_off = (regs == 3) ? OMAP3430ES2_CM_FCLKEN3 : CM_FCLKEN1; u16 iclk_off = (regs == 3) ? CM_ICLKEN3 : CM_ICLKEN1; u16 grpsel_off = (regs == 3) ? OMAP3430ES2_PM_MPUGRPSEL3 : OMAP3430_PM_MPUGRPSEL; int c = 0; wkst = prm_read_mod_reg(module, wkst_off); wkst &= prm_read_mod_reg(module, grpsel_off); if (wkst) { iclk = cm_read_mod_reg(module, iclk_off); fclk = cm_read_mod_reg(module, fclk_off); while (wkst) { clken = wkst; cm_set_mod_reg_bits(clken, module, iclk_off); /* * For USBHOST, we don't know whether HOST1 or * HOST2 woke us up, so enable both f-clocks */ if (module == OMAP3430ES2_USBHOST_MOD) clken |= 1 << OMAP3430ES2_EN_USBHOST2_SHIFT; cm_set_mod_reg_bits(clken, module, fclk_off); prm_write_mod_reg(wkst, module, wkst_off); wkst = prm_read_mod_reg(module, wkst_off); c++; } cm_write_mod_reg(iclk, module, iclk_off); cm_write_mod_reg(fclk, module, fclk_off); } return c; } static int _prcm_int_handle_wakeup(void) { int c; c = prcm_clear_mod_irqs(WKUP_MOD, 1); c += prcm_clear_mod_irqs(CORE_MOD, 1); c += prcm_clear_mod_irqs(OMAP3430_PER_MOD, 1); if (omap_rev() > OMAP3430_REV_ES1_0) { c += prcm_clear_mod_irqs(CORE_MOD, 3); c += prcm_clear_mod_irqs(OMAP3430ES2_USBHOST_MOD, 1); } return c; } /* * PRCM Interrupt Handler * * The PRM_IRQSTATUS_MPU register indicates if there are any pending * interrupts from the PRCM for the MPU. These bits must be cleared in * order to clear the PRCM interrupt. The PRCM interrupt handler is * implemented to simply clear the PRM_IRQSTATUS_MPU in order to clear * the PRCM interrupt. Please note that bit 0 of the PRM_IRQSTATUS_MPU * register indicates that a wake-up event is pending for the MPU and * this bit can only be cleared if the all the wake-up events latched * in the various PM_WKST_x registers have been cleared. The interrupt * handler is implemented using a do-while loop so that if a wake-up * event occurred during the processing of the prcm interrupt handler * (setting a bit in the corresponding PM_WKST_x register and thus * preventing us from clearing bit 0 of the PRM_IRQSTATUS_MPU register) * this would be handled. */ static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id) { u32 irqenable_mpu, irqstatus_mpu; int c = 0; irqenable_mpu = prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET); irqstatus_mpu = prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); irqstatus_mpu &= irqenable_mpu; do { if (irqstatus_mpu & (OMAP3430_WKUP_ST_MASK | OMAP3430_IO_ST_MASK)) { c = _prcm_int_handle_wakeup(); /* * Is the MPU PRCM interrupt handler racing with the * IVA2 PRCM interrupt handler ? */ WARN(c == 0, "prcm: WARNING: PRCM indicated MPU wakeup " "but no wakeup sources are marked\n"); } else { /* XXX we need to expand our PRCM interrupt handler */ WARN(1, "prcm: WARNING: PRCM interrupt received, but " "no code to handle it (%08x)\n", irqstatus_mpu); } prm_write_mod_reg(irqstatus_mpu, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); irqstatus_mpu = prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); irqstatus_mpu &= irqenable_mpu; } while (irqstatus_mpu); return IRQ_HANDLED; } static void restore_control_register(u32 val) { __asm__ __volatile__ ("mcr p15, 0, %0, c1, c0, 0" : : "r" (val)); } /* Function to restore the table entry that was modified for enabling MMU */ static void restore_table_entry(void) { void __iomem *scratchpad_address; u32 previous_value, control_reg_value; u32 *address; scratchpad_address = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD); /* Get address of entry that was modified */ address = (u32 *)__raw_readl(scratchpad_address + OMAP343X_TABLE_ADDRESS_OFFSET); /* Get the previous value which needs to be restored */ previous_value = __raw_readl(scratchpad_address + OMAP343X_TABLE_VALUE_OFFSET); address = __va(address); *address = previous_value; flush_tlb_all(); control_reg_value = __raw_readl(scratchpad_address + OMAP343X_CONTROL_REG_VALUE_OFFSET); /* This will enable caches and prediction */ restore_control_register(control_reg_value); } void omap_sram_idle(void) { /* Variable to tell what needs to be saved and restored * in omap_sram_idle*/ /* save_state = 0 => Nothing to save and restored */ /* save_state = 1 => Only L1 and logic lost */ /* save_state = 2 => Only L2 lost */ /* save_state = 3 => L1, L2 and logic lost */ int save_state = 0; int mpu_next_state = PWRDM_POWER_ON; int per_next_state = PWRDM_POWER_ON; int core_next_state = PWRDM_POWER_ON; int core_prev_state, per_prev_state; u32 sdrc_pwr = 0; if (!_omap_sram_idle) return; pwrdm_clear_all_prev_pwrst(mpu_pwrdm); pwrdm_clear_all_prev_pwrst(neon_pwrdm); pwrdm_clear_all_prev_pwrst(core_pwrdm); pwrdm_clear_all_prev_pwrst(per_pwrdm); mpu_next_state = pwrdm_read_next_pwrst(mpu_pwrdm); switch (mpu_next_state) { case PWRDM_POWER_ON: case PWRDM_POWER_RET: /* No need to save context */ save_state = 0; break; case PWRDM_POWER_OFF: save_state = 3; break; default: /* Invalid state */ printk(KERN_ERR "Invalid mpu state in sram_idle\n"); return; } pwrdm_pre_transition(); /* NEON control */ if (pwrdm_read_pwrst(neon_pwrdm) == PWRDM_POWER_ON) pwrdm_set_next_pwrst(neon_pwrdm, mpu_next_state); /* Enable IO-PAD and IO-CHAIN wakeups */ per_next_state = pwrdm_read_next_pwrst(per_pwrdm); core_next_state = pwrdm_read_next_pwrst(core_pwrdm); if (omap3_has_io_wakeup() && (per_next_state < PWRDM_POWER_ON || core_next_state < PWRDM_POWER_ON)) { prm_set_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN); omap3_enable_io_chain(); } /* Block console output in case it is on one of the OMAP UARTs */ if (!is_suspending()) if (per_next_state < PWRDM_POWER_ON || core_next_state < PWRDM_POWER_ON) if (try_acquire_console_sem()) goto console_still_active; /* PER */ if (per_next_state < PWRDM_POWER_ON) { omap_uart_prepare_idle(2); omap_uart_prepare_idle(3); omap2_gpio_prepare_for_idle(per_next_state); if (per_next_state == PWRDM_POWER_OFF) omap3_per_save_context(); } /* CORE */ if (core_next_state < PWRDM_POWER_ON) { omap_uart_prepare_idle(0); omap_uart_prepare_idle(1); if (core_next_state == PWRDM_POWER_OFF) { omap3_core_save_context(); omap3_cm_save_context(); } } omap3_intc_prepare_idle(); /* * On EMU/HS devices ROM code restores a SRDC value * from scratchpad which has automatic self refresh on timeout * of AUTO_CNT = 1 enabled. This takes care of erratum ID i443. * Hence store/restore the SDRC_POWER register here. */ if (omap_rev() >= OMAP3430_REV_ES3_0 && omap_type() != OMAP2_DEVICE_TYPE_GP && core_next_state == PWRDM_POWER_OFF) sdrc_pwr = sdrc_read_reg(SDRC_POWER); /* * omap3_arm_context is the location where ARM registers * get saved. The restore path then reads from this * location and restores them back. */ _omap_sram_idle(omap3_arm_context, save_state); cpu_init(); /* Restore normal SDRC POWER settings */ if (omap_rev() >= OMAP3430_REV_ES3_0 && omap_type() != OMAP2_DEVICE_TYPE_GP && core_next_state == PWRDM_POWER_OFF) sdrc_write_reg(sdrc_pwr, SDRC_POWER); /* Restore table entry modified during MMU restoration */ if (pwrdm_read_prev_pwrst(mpu_pwrdm) == PWRDM_POWER_OFF) restore_table_entry(); /* CORE */ if (core_next_state < PWRDM_POWER_ON) { core_prev_state = pwrdm_read_prev_pwrst(core_pwrdm); if (core_prev_state == PWRDM_POWER_OFF) { omap3_core_restore_context(); omap3_cm_restore_context(); omap3_sram_restore_context(); omap2_sms_restore_context(); } omap_uart_resume_idle(0); omap_uart_resume_idle(1); if (core_next_state == PWRDM_POWER_OFF) prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK, OMAP3430_GR_MOD, OMAP3_PRM_VOLTCTRL_OFFSET); } omap3_intc_resume_idle(); /* PER */ if (per_next_state < PWRDM_POWER_ON) { per_prev_state = pwrdm_read_prev_pwrst(per_pwrdm); omap2_gpio_resume_after_idle(); if (per_prev_state == PWRDM_POWER_OFF) omap3_per_restore_context(); omap_uart_resume_idle(2); omap_uart_resume_idle(3); } if (!is_suspending()) release_console_sem(); console_still_active: /* Disable IO-PAD and IO-CHAIN wakeup */ if (omap3_has_io_wakeup() && (per_next_state < PWRDM_POWER_ON || core_next_state < PWRDM_POWER_ON)) { prm_clear_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN); omap3_disable_io_chain(); } pwrdm_post_transition(); omap2_clkdm_allow_idle(mpu_pwrdm->pwrdm_clkdms[0]); } int omap3_can_sleep(void) { if (!sleep_while_idle) return 0; if (!omap_uart_can_sleep()) return 0; return 1; } static void omap3_pm_idle(void) { local_irq_disable(); local_fiq_disable(); if (!omap3_can_sleep()) goto out; if (omap_irq_pending() || need_resched()) goto out; omap_sram_idle(); out: local_fiq_enable(); local_irq_enable(); } #ifdef CONFIG_SUSPEND static int omap3_pm_suspend(void) { struct power_state *pwrst; int state, ret = 0; if (wakeup_timer_seconds || wakeup_timer_milliseconds) omap2_pm_wakeup_on_timer(wakeup_timer_seconds, wakeup_timer_milliseconds); /* Read current next_pwrsts */ list_for_each_entry(pwrst, &pwrst_list, node) pwrst->saved_state = pwrdm_read_next_pwrst(pwrst->pwrdm); /* Set ones wanted by suspend */ list_for_each_entry(pwrst, &pwrst_list, node) { if (omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state)) goto restore; if (pwrdm_clear_all_prev_pwrst(pwrst->pwrdm)) goto restore; } omap_uart_prepare_suspend(); omap3_intc_suspend(); omap_sram_idle(); restore: /* Restore next_pwrsts */ list_for_each_entry(pwrst, &pwrst_list, node) { state = pwrdm_read_prev_pwrst(pwrst->pwrdm); if (state > pwrst->next_state) { printk(KERN_INFO "Powerdomain (%s) didn't enter " "target state %d\n", pwrst->pwrdm->name, pwrst->next_state); ret = -1; } omap_set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state); } if (ret) printk(KERN_ERR "Could not enter target state in pm_suspend\n"); else printk(KERN_INFO "Successfully put all powerdomains " "to target state\n"); return ret; } static int omap3_pm_enter(suspend_state_t unused) { int ret = 0; switch (suspend_state) { case PM_SUSPEND_STANDBY: case PM_SUSPEND_MEM: ret = omap3_pm_suspend(); break; default: ret = -EINVAL; } return ret; } /* Hooks to enable / disable UART interrupts during suspend */ static int omap3_pm_begin(suspend_state_t state) { disable_hlt(); suspend_state = state; omap_uart_enable_irqs(0); return 0; } static void omap3_pm_end(void) { suspend_state = PM_SUSPEND_ON; omap_uart_enable_irqs(1); enable_hlt(); return; } static struct platform_suspend_ops omap_pm_ops = { .begin = omap3_pm_begin, .end = omap3_pm_end, .enter = omap3_pm_enter, .valid = suspend_valid_only_mem, }; #endif /* CONFIG_SUSPEND */ /** * omap3_iva_idle(): ensure IVA is in idle so it can be put into * retention * * In cases where IVA2 is activated by bootcode, it may prevent * full-chip retention or off-mode because it is not idle. This * function forces the IVA2 into idle state so it can go * into retention/off and thus allow full-chip retention/off. * **/ static void __init omap3_iva_idle(void) { /* ensure IVA2 clock is disabled */ cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN); /* if no clock activity, nothing else to do */ if (!(cm_read_mod_reg(OMAP3430_IVA2_MOD, OMAP3430_CM_CLKSTST) & OMAP3430_CLKACTIVITY_IVA2_MASK)) return; /* Reset IVA2 */ prm_write_mod_reg(OMAP3430_RST1_IVA2_MASK | OMAP3430_RST2_IVA2_MASK | OMAP3430_RST3_IVA2_MASK, OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL); /* Enable IVA2 clock */ cm_write_mod_reg(OMAP3430_CM_FCLKEN_IVA2_EN_IVA2_MASK, OMAP3430_IVA2_MOD, CM_FCLKEN); /* Set IVA2 boot mode to 'idle' */ omap_ctrl_writel(OMAP3_IVA2_BOOTMOD_IDLE, OMAP343X_CONTROL_IVA2_BOOTMOD); /* Un-reset IVA2 */ prm_write_mod_reg(0, OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL); /* Disable IVA2 clock */ cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN); /* Reset IVA2 */ prm_write_mod_reg(OMAP3430_RST1_IVA2_MASK | OMAP3430_RST2_IVA2_MASK | OMAP3430_RST3_IVA2_MASK, OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL); } static void __init omap3_d2d_idle(void) { u16 mask, padconf; /* In a stand alone OMAP3430 where there is not a stacked * modem for the D2D Idle Ack and D2D MStandby must be pulled * high. S CONTROL_PADCONF_SAD2D_IDLEACK and * CONTROL_PADCONF_SAD2D_MSTDBY to have a pull up. */ mask = (1 << 4) | (1 << 3); /* pull-up, enabled */ padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_MSTANDBY); padconf |= mask; omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_MSTANDBY); padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_IDLEACK); padconf |= mask; omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_IDLEACK); /* reset modem */ prm_write_mod_reg(OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RSTPWRON_MASK | OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RST_MASK, CORE_MOD, OMAP2_RM_RSTCTRL); prm_write_mod_reg(0, CORE_MOD, OMAP2_RM_RSTCTRL); } static void __init prcm_setup_regs(void) { u32 omap3630_auto_uart4_mask = cpu_is_omap3630() ? OMAP3630_AUTO_UART4_MASK : 0; u32 omap3630_en_uart4_mask = cpu_is_omap3630() ? OMAP3630_EN_UART4_MASK : 0; u32 omap3630_grpsel_uart4_mask = cpu_is_omap3630() ? OMAP3630_GRPSEL_UART4_MASK : 0; /* XXX Reset all wkdeps. This should be done when initializing * powerdomains */ prm_write_mod_reg(0, OMAP3430_IVA2_MOD, PM_WKDEP); prm_write_mod_reg(0, MPU_MOD, PM_WKDEP); prm_write_mod_reg(0, OMAP3430_DSS_MOD, PM_WKDEP); prm_write_mod_reg(0, OMAP3430_NEON_MOD, PM_WKDEP); prm_write_mod_reg(0, OMAP3430_CAM_MOD, PM_WKDEP); prm_write_mod_reg(0, OMAP3430_PER_MOD, PM_WKDEP); if (omap_rev() > OMAP3430_REV_ES1_0) { prm_write_mod_reg(0, OMAP3430ES2_SGX_MOD, PM_WKDEP); prm_write_mod_reg(0, OMAP3430ES2_USBHOST_MOD, PM_WKDEP); } else prm_write_mod_reg(0, GFX_MOD, PM_WKDEP); /* * Enable interface clock autoidle for all modules. * Note that in the long run this should be done by clockfw */ cm_write_mod_reg( OMAP3430_AUTO_MODEM_MASK | OMAP3430ES2_AUTO_MMC3_MASK | OMAP3430ES2_AUTO_ICR_MASK | OMAP3430_AUTO_AES2_MASK | OMAP3430_AUTO_SHA12_MASK | OMAP3430_AUTO_DES2_MASK | OMAP3430_AUTO_MMC2_MASK | OMAP3430_AUTO_MMC1_MASK | OMAP3430_AUTO_MSPRO_MASK | OMAP3430_AUTO_HDQ_MASK | OMAP3430_AUTO_MCSPI4_MASK | OMAP3430_AUTO_MCSPI3_MASK | OMAP3430_AUTO_MCSPI2_MASK | OMAP3430_AUTO_MCSPI1_MASK | OMAP3430_AUTO_I2C3_MASK | OMAP3430_AUTO_I2C2_MASK | OMAP3430_AUTO_I2C1_MASK | OMAP3430_AUTO_UART2_MASK | OMAP3430_AUTO_UART1_MASK | OMAP3430_AUTO_GPT11_MASK | OMAP3430_AUTO_GPT10_MASK | OMAP3430_AUTO_MCBSP5_MASK | OMAP3430_AUTO_MCBSP1_MASK | OMAP3430ES1_AUTO_FAC_MASK | /* This is es1 only */ OMAP3430_AUTO_MAILBOXES_MASK | OMAP3430_AUTO_OMAPCTRL_MASK | OMAP3430ES1_AUTO_FSHOSTUSB_MASK | OMAP3430_AUTO_HSOTGUSB_MASK | OMAP3430_AUTO_SAD2D_MASK | OMAP3430_AUTO_SSI_MASK, CORE_MOD, CM_AUTOIDLE1); cm_write_mod_reg( OMAP3430_AUTO_PKA_MASK | OMAP3430_AUTO_AES1_MASK | OMAP3430_AUTO_RNG_MASK | OMAP3430_AUTO_SHA11_MASK | OMAP3430_AUTO_DES1_MASK, CORE_MOD, CM_AUTOIDLE2); if (omap_rev() > OMAP3430_REV_ES1_0) { cm_write_mod_reg( OMAP3430_AUTO_MAD2D_MASK | OMAP3430ES2_AUTO_USBTLL_MASK, CORE_MOD, CM_AUTOIDLE3); } cm_write_mod_reg( OMAP3430_AUTO_WDT2_MASK | OMAP3430_AUTO_WDT1_MASK | OMAP3430_AUTO_GPIO1_MASK | OMAP3430_AUTO_32KSYNC_MASK | OMAP3430_AUTO_GPT12_MASK | OMAP3430_AUTO_GPT1_MASK, WKUP_MOD, CM_AUTOIDLE); cm_write_mod_reg( OMAP3430_AUTO_DSS_MASK, OMAP3430_DSS_MOD, CM_AUTOIDLE); cm_write_mod_reg( OMAP3430_AUTO_CAM_MASK, OMAP3430_CAM_MOD, CM_AUTOIDLE); cm_write_mod_reg( omap3630_auto_uart4_mask | OMAP3430_AUTO_GPIO6_MASK | OMAP3430_AUTO_GPIO5_MASK | OMAP3430_AUTO_GPIO4_MASK | OMAP3430_AUTO_GPIO3_MASK | OMAP3430_AUTO_GPIO2_MASK | OMAP3430_AUTO_WDT3_MASK | OMAP3430_AUTO_UART3_MASK | OMAP3430_AUTO_GPT9_MASK | OMAP3430_AUTO_GPT8_MASK | OMAP3430_AUTO_GPT7_MASK | OMAP3430_AUTO_GPT6_MASK | OMAP3430_AUTO_GPT5_MASK | OMAP3430_AUTO_GPT4_MASK | OMAP3430_AUTO_GPT3_MASK | OMAP3430_AUTO_GPT2_MASK | OMAP3430_AUTO_MCBSP4_MASK | OMAP3430_AUTO_MCBSP3_MASK | OMAP3430_AUTO_MCBSP2_MASK, OMAP3430_PER_MOD, CM_AUTOIDLE); if (omap_rev() > OMAP3430_REV_ES1_0) { cm_write_mod_reg( OMAP3430ES2_AUTO_USBHOST_MASK, OMAP3430ES2_USBHOST_MOD, CM_AUTOIDLE); } omap_ctrl_writel(OMAP3430_AUTOIDLE_MASK, OMAP2_CONTROL_SYSCONFIG); /* * Set all plls to autoidle. This is needed until autoidle is * enabled by clockfw */ cm_write_mod_reg(1 << OMAP3430_AUTO_IVA2_DPLL_SHIFT, OMAP3430_IVA2_MOD, CM_AUTOIDLE2); cm_write_mod_reg(1 << OMAP3430_AUTO_MPU_DPLL_SHIFT, MPU_MOD, CM_AUTOIDLE2); cm_write_mod_reg((1 << OMAP3430_AUTO_PERIPH_DPLL_SHIFT) | (1 << OMAP3430_AUTO_CORE_DPLL_SHIFT), PLL_MOD, CM_AUTOIDLE); cm_write_mod_reg(1 << OMAP3430ES2_AUTO_PERIPH2_DPLL_SHIFT, PLL_MOD, CM_AUTOIDLE2); /* * Enable control of expternal oscillator through * sys_clkreq. In the long run clock framework should * take care of this. */ prm_rmw_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK, 1 << OMAP_AUTOEXTCLKMODE_SHIFT, OMAP3430_GR_MOD, OMAP3_PRM_CLKSRC_CTRL_OFFSET); /* setup wakup source */ prm_write_mod_reg(OMAP3430_EN_IO_MASK | OMAP3430_EN_GPIO1_MASK | OMAP3430_EN_GPT1_MASK | OMAP3430_EN_GPT12_MASK, WKUP_MOD, PM_WKEN); /* No need to write EN_IO, that is always enabled */ prm_write_mod_reg(OMAP3430_GRPSEL_GPIO1_MASK | OMAP3430_GRPSEL_GPT1_MASK | OMAP3430_GRPSEL_GPT12_MASK, WKUP_MOD, OMAP3430_PM_MPUGRPSEL); /* For some reason IO doesn't generate wakeup event even if * it is selected to mpu wakeup goup */ prm_write_mod_reg(OMAP3430_IO_EN_MASK | OMAP3430_WKUP_EN_MASK, OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET); /* Enable PM_WKEN to support DSS LPR */ prm_write_mod_reg(OMAP3430_PM_WKEN_DSS_EN_DSS_MASK, OMAP3430_DSS_MOD, PM_WKEN); /* Enable wakeups in PER */ prm_write_mod_reg(omap3630_en_uart4_mask | OMAP3430_EN_GPIO2_MASK | OMAP3430_EN_GPIO3_MASK | OMAP3430_EN_GPIO4_MASK | OMAP3430_EN_GPIO5_MASK | OMAP3430_EN_GPIO6_MASK | OMAP3430_EN_UART3_MASK | OMAP3430_EN_MCBSP2_MASK | OMAP3430_EN_MCBSP3_MASK | OMAP3430_EN_MCBSP4_MASK, OMAP3430_PER_MOD, PM_WKEN); /* and allow them to wake up MPU */ prm_write_mod_reg(omap3630_grpsel_uart4_mask | OMAP3430_GRPSEL_GPIO2_MASK | OMAP3430_GRPSEL_GPIO3_MASK | OMAP3430_GRPSEL_GPIO4_MASK | OMAP3430_GRPSEL_GPIO5_MASK | OMAP3430_GRPSEL_GPIO6_MASK | OMAP3430_GRPSEL_UART3_MASK | OMAP3430_GRPSEL_MCBSP2_MASK | OMAP3430_GRPSEL_MCBSP3_MASK | OMAP3430_GRPSEL_MCBSP4_MASK, OMAP3430_PER_MOD, OMAP3430_PM_MPUGRPSEL); /* Don't attach IVA interrupts */ prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL); prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1); prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3); prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL); /* Clear any pending 'reset' flags */ prm_write_mod_reg(0xffffffff, MPU_MOD, OMAP2_RM_RSTST); prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP2_RM_RSTST); prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, OMAP2_RM_RSTST); prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, OMAP2_RM_RSTST); prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, OMAP2_RM_RSTST); prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, OMAP2_RM_RSTST); prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, OMAP2_RM_RSTST); /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); omap3_iva_idle(); omap3_d2d_idle(); } void omap3_pm_off_mode_enable(int enable) { struct power_state *pwrst; u32 state; if (enable) state = PWRDM_POWER_OFF; else state = PWRDM_POWER_RET; #ifdef CONFIG_CPU_IDLE /* * Erratum i583: implementation for ES rev < Es1.2 on 3630. We cannot * enable OFF mode in a stable form for previous revisions, restrict * instead to RET */ if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583)) omap3_cpuidle_update_states(state, PWRDM_POWER_RET); else omap3_cpuidle_update_states(state, state); #endif list_for_each_entry(pwrst, &pwrst_list, node) { if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583) && pwrst->pwrdm == core_pwrdm && state == PWRDM_POWER_OFF) { pwrst->next_state = PWRDM_POWER_RET; WARN_ONCE(1, "%s: Core OFF disabled due to errata i583\n", __func__); } else { pwrst->next_state = state; } omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state); } } int omap3_pm_get_suspend_state(struct powerdomain *pwrdm) { struct power_state *pwrst; list_for_each_entry(pwrst, &pwrst_list, node) { if (pwrst->pwrdm == pwrdm) return pwrst->next_state; } return -EINVAL; } int omap3_pm_set_suspend_state(struct powerdomain *pwrdm, int state) { struct power_state *pwrst; list_for_each_entry(pwrst, &pwrst_list, node) { if (pwrst->pwrdm == pwrdm) { pwrst->next_state = state; return 0; } } return -EINVAL; } static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused) { struct power_state *pwrst; if (!pwrdm->pwrsts) return 0; pwrst = kmalloc(sizeof(struct power_state), GFP_ATOMIC); if (!pwrst) return -ENOMEM; pwrst->pwrdm = pwrdm; pwrst->next_state = PWRDM_POWER_RET; list_add(&pwrst->node, &pwrst_list); if (pwrdm_has_hdwr_sar(pwrdm)) pwrdm_enable_hdwr_sar(pwrdm); return omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state); } /* * Enable hw supervised mode for all clockdomains if it's * supported. Initiate sleep transition for other clockdomains, if * they are not used */ static int __init clkdms_setup(struct clockdomain *clkdm, void *unused) { if (clkdm->flags & CLKDM_CAN_ENABLE_AUTO) omap2_clkdm_allow_idle(clkdm); else if (clkdm->flags & CLKDM_CAN_FORCE_SLEEP && atomic_read(&clkdm->usecount) == 0) omap2_clkdm_sleep(clkdm); return 0; } void omap_push_sram_idle(void) { _omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend, omap34xx_cpu_suspend_sz); if (omap_type() != OMAP2_DEVICE_TYPE_GP) _omap_save_secure_sram = omap_sram_push(save_secure_ram_context, save_secure_ram_context_sz); } static void __init pm_errata_configure(void) { if (cpu_is_omap3630()) { pm34xx_errata |= PM_RTA_ERRATUM_i608; /* Enable the l2 cache toggling in sleep logic */ enable_omap3630_toggle_l2_on_restore(); if (omap_rev() < OMAP3630_REV_ES1_2) pm34xx_errata |= PM_SDRC_WAKEUP_ERRATUM_i583; } } static int __init omap3_pm_init(void) { struct power_state *pwrst, *tmp; struct clockdomain *neon_clkdm, *per_clkdm, *mpu_clkdm, *core_clkdm; int ret; if (!cpu_is_omap34xx()) return -ENODEV; pm_errata_configure(); printk(KERN_ERR "Power Management for TI OMAP3.\n"); /* XXX prcm_setup_regs needs to be before enabling hw * supervised mode for powerdomains */ prcm_setup_regs(); ret = request_irq(INT_34XX_PRCM_MPU_IRQ, (irq_handler_t)prcm_interrupt_handler, IRQF_DISABLED, "prcm", NULL); if (ret) { printk(KERN_ERR "request_irq failed to register for 0x%x\n", INT_34XX_PRCM_MPU_IRQ); goto err1; } ret = pwrdm_for_each(pwrdms_setup, NULL); if (ret) { printk(KERN_ERR "Failed to setup powerdomains\n"); goto err2; } (void) clkdm_for_each(clkdms_setup, NULL); mpu_pwrdm = pwrdm_lookup("mpu_pwrdm"); if (mpu_pwrdm == NULL) { printk(KERN_ERR "Failed to get mpu_pwrdm\n"); goto err2; } neon_pwrdm = pwrdm_lookup("neon_pwrdm"); per_pwrdm = pwrdm_lookup("per_pwrdm"); core_pwrdm = pwrdm_lookup("core_pwrdm"); cam_pwrdm = pwrdm_lookup("cam_pwrdm"); neon_clkdm = clkdm_lookup("neon_clkdm"); mpu_clkdm = clkdm_lookup("mpu_clkdm"); per_clkdm = clkdm_lookup("per_clkdm"); core_clkdm = clkdm_lookup("core_clkdm"); omap_push_sram_idle(); #ifdef CONFIG_SUSPEND suspend_set_ops(&omap_pm_ops); #endif /* CONFIG_SUSPEND */ pm_idle = omap3_pm_idle; omap3_idle_init(); /* * RTA is disabled during initialization as per erratum i608 * it is safer to disable RTA by the bootloader, but we would like * to be doubly sure here and prevent any mishaps. */ if (IS_PM34XX_ERRATUM(PM_RTA_ERRATUM_i608)) omap3630_ctrl_disable_rta(); clkdm_add_wkdep(neon_clkdm, mpu_clkdm); if (omap_type() != OMAP2_DEVICE_TYPE_GP) { omap3_secure_ram_storage = kmalloc(0x803F, GFP_KERNEL); if (!omap3_secure_ram_storage) printk(KERN_ERR "Memory allocation failed when" "allocating for secure sram context\n"); local_irq_disable(); local_fiq_disable(); omap_dma_global_context_save(); omap3_save_secure_ram_context(PWRDM_POWER_ON); omap_dma_global_context_restore(); local_irq_enable(); local_fiq_enable(); } omap3_save_scratchpad_contents(); err1: return ret; err2: free_irq(INT_34XX_PRCM_MPU_IRQ, NULL); list_for_each_entry_safe(pwrst, tmp, &pwrst_list, node) { list_del(&pwrst->node); kfree(pwrst); } return ret; } late_initcall(omap3_pm_init);