# # Touchscreen driver configuration # menuconfig INPUT_TOUCHSCREEN bool "Touchscreens" help Say Y here, and a list of supported touchscreens will be displayed. This option doesn't affect the kernel. If unsure, say Y. if INPUT_TOUCHSCREEN config TOUCHSCREEN_88PM860X tristate "Marvell 88PM860x touchscreen" depends on MFD_88PM860X help Say Y here if you have a 88PM860x PMIC and want to enable support for the built-in touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called 88pm860x-ts. config TOUCHSCREEN_ADS7846 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens" depends on SPI_MASTER depends on HWMON = n || HWMON help Say Y here if you have a touchscreen interface using the ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller, and your board-specific setup code includes that in its table of SPI devices. If HWMON is selected, and the driver is told the reference voltage on your board, you will also get hwmon interfaces for the voltage (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ads7846. config TOUCHSCREEN_AD7877 tristate "AD7877 based touchscreens" depends on SPI_MASTER help Say Y here if you have a touchscreen interface using the AD7877 controller, and your board-specific initialization code includes that in its table of SPI devices. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ad7877. config TOUCHSCREEN_AD7879_I2C tristate "AD7879 based touchscreens: AD7879-1 I2C Interface" depends on I2C select TOUCHSCREEN_AD7879 help Say Y here if you have a touchscreen interface using the AD7879-1/AD7889-1 controller, and your board-specific initialization code includes that in its table of I2C devices. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ad7879. config TOUCHSCREEN_AD7879_SPI tristate "AD7879 based touchscreens: AD7879 SPI Interface" depends on SPI_MASTER && TOUCHSCREEN_AD7879_I2C = n select TOUCHSCREEN_AD7879 help Say Y here if you have a touchscreen interface using the AD7879/AD7889 controller, and your board-specific initialization code includes that in its table of SPI devices. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ad7879. config TOUCHSCREEN_AD7879 tristate default n config TOUCHSCREEN_BITSY tristate "Compaq iPAQ H3600 (Bitsy) touchscreen" depends on SA1100_BITSY select SERIO help Say Y here if you have the h3600 (Bitsy) touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called h3600_ts_input. config TOUCHSCREEN_DA9034 tristate "Touchscreen support for Dialog Semiconductor DA9034" depends on PMIC_DA903X default y help Say Y here to enable the support for the touchscreen found on Dialog Semiconductor DA9034 PMIC. config TOUCHSCREEN_DYNAPRO tristate "Dynapro serial touchscreen" select SERIO help Say Y here if you have a Dynapro serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called dynapro. config TOUCHSCREEN_HAMPSHIRE tristate "Hampshire serial touchscreen" select SERIO help Say Y here if you have a Hampshire serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called hampshire. config TOUCHSCREEN_EETI tristate "EETI touchscreen panel support" depends on I2C help Say Y here to enable support for I2C connected EETI touch panels. To compile this driver as a module, choose M here: the module will be called eeti_ts. config TOUCHSCREEN_FUJITSU tristate "Fujitsu serial touchscreen" select SERIO help Say Y here if you have the Fujitsu touchscreen (such as one installed in Lifebook P series laptop) connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called fujitsu-ts. config TOUCHSCREEN_S3C2410 tristate "Samsung S3C2410/generic touchscreen input driver" depends on ARCH_S3C2410 || SAMSUNG_DEV_TS select S3C_ADC help Say Y here if you have the s3c2410 touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called s3c2410_ts. config TOUCHSCREEN_GUNZE tristate "Gunze AHL-51S touchscreen" select SERIO help Say Y here if you have the Gunze AHL-51 touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called gunze. config TOUCHSCREEN_ELO tristate "Elo serial touchscreens" select SERIO help Say Y here if you have an Elo serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called elo. config TOUCHSCREEN_WACOM_W8001 tristate "Wacom W8001 penabled serial touchscreen" select SERIO help Say Y here if you have an Wacom W8001 penabled serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called wacom_w8001. config TOUCHSCREEN_MCS5000 tristate "MELFAS MCS-5000 touchscreen" depends on I2C help Say Y here if you have the MELFAS MCS-5000 touchscreen controller chip in your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mcs5000_ts. config TOUCHSCREEN_MTOUCH tristate "MicroTouch serial touchscreens" select SERIO help Say Y here if you have a MicroTouch (3M) serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mtouch. config TOUCHSCREEN_INEXIO tristate "iNexio serial touchscreens" select SERIO help Say Y here if you have an iNexio serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called inexio. config TOUCHSCREEN_INTEL_MID tristate "Intel MID platform resistive touchscreen" depends on INTEL_SCU_IPC help Say Y here if you have a Intel MID based touchscreen in your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called intel_mid_touch. config TOUCHSCREEN_MK712 tristate "ICS MicroClock MK712 touchscreen" help Say Y here if you have the ICS MicroClock MK712 touchscreen controller chip in your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mk712. config TOUCHSCREEN_HP600 tristate "HP Jornada 6xx touchscreen" depends on SH_HP6XX && SH_ADC help Say Y here if you have a HP Jornada 620/660/680/690 and want to support the built-in touchscreen. To compile this driver as a module, choose M here: the module will be called hp680_ts_input. config TOUCHSCREEN_HP7XX tristate "HP Jornada 7xx touchscreen" depends on SA1100_JORNADA720_SSP help Say Y here if you have a HP Jornada 710/720/728 and want to support the built-in touchscreen. To compile this driver as a module, choose M here: the module will be called jornada720_ts. config TOUCHSCREEN_HTCPEN tristate "HTC Shift X9500 touchscreen" depends on ISA help Say Y here if you have an HTC Shift UMPC also known as HTC X9500 Clio / Shangrila and want to support the built-in touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called htcpen. config TOUCHSCREEN_PENMOUNT tristate "Penmount serial touchscreen" select SERIO help Say Y here if you have a Penmount serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called penmount. config TOUCHSCREEN_MIGOR tristate "Renesas MIGO-R touchscreen" depends on SH_MIGOR && I2C help Say Y here to enable MIGO-R touchscreen support. If unsure, say N. To compile this driver as a module, choose M here: the module will be called migor_ts. config TOUCHSCREEN_TOUCHRIGHT tristate "Touchright serial touchscreen" select SERIO help Say Y here if you have a Touchright serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called touchright. config TOUCHSCREEN_TOUCHWIN tristate "Touchwin serial touchscreen" select SERIO help Say Y here if you have a Touchwin serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called touchwin. config TOUCHSCREEN_ATMEL_TSADCC tristate "Atmel Touchscreen Interface" depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45 help Say Y here if you have a 4-wire touchscreen connected to the ADC Controller on your Atmel SoC (such as the AT91SAM9RL). If unsure, say N. To compile this driver as a module, choose M here: the module will be called atmel_tsadcc. config TOUCHSCREEN_UCB1400 tristate "Philips UCB1400 touchscreen" depends on AC97_BUS depends on UCB1400_CORE help This enables support for the Philips UCB1400 touchscreen interface. The UCB1400 is an AC97 audio codec. The touchscreen interface will be initialized only after the ALSA subsystem has been brought up and the UCB1400 detected. You therefore have to configure ALSA support as well (either built-in or modular, independently of whether this driver is itself built-in or modular) for this driver to work. To compile this driver as a module, choose M here: the module will be called ucb1400_ts. config TOUCHSCREEN_WM97XX tristate "Support for WM97xx AC97 touchscreen controllers" depends on AC97_BUS help Say Y here if you have a Wolfson Microelectronics WM97xx touchscreen connected to your system. Note that this option only enables core driver, you will also need to select support for appropriate chip below. If unsure, say N. To compile this driver as a module, choose M here: the module will be called wm97xx-ts. config TOUCHSCREEN_WM9705 bool "WM9705 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX default y help Say Y here to enable support for the Wolfson Microelectronics WM9705 touchscreen controller. config TOUCHSCREEN_WM9712 bool "WM9712 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX default y help Say Y here to enable support for the Wolfson Microelectronics WM9712 touchscreen controller. config TOUCHSCREEN_WM9713 bool "WM9713 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX default y help Say Y here to enable support for the Wolfson Microelectronics WM9713 touchscreen controller. config TOUCHSCREEN_WM97XX_ATMEL tristate "WM97xx Atmel accelerated touch" depends on TOUCHSCREEN_WM97XX && (AVR32 || ARCH_AT91) help Say Y here for support for streaming mode with WM97xx touchscreens on Atmel AT91 or AVR32 systems with an AC97C module. Be aware that this will use channel B in the controller for streaming data, this must not conflict with other AC97C drivers. If unsure, say N. To compile this driver as a module, choose M here: the module will be called atmel-wm97xx. config TOUCHSCREEN_WM97XX_MAINSTONE tristate "WM97xx Mainstone/Palm accelerated touch" depends on TOUCHSCREEN_WM97XX && ARCH_PXA help Say Y here for support for streaming mode with WM97xx touchscreens on Mainstone, Palm Tungsten T5, TX and LifeDrive systems. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mainstone-wm97xx. config TOUCHSCREEN_WM97XX_ZYLONITE tristate "Zylonite accelerated touch" depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE select TOUCHSCREEN_WM9713 help Say Y here for support for streaming mode with the touchscreen on Zylonite systems. If unsure, say N. To compile this driver as a module, choose M here: the module will be called zylonite-wm97xx. config TOUCHSCREEN_USB_COMPOSITE tristate "USB Touchscreen Driver" depends on USB_ARCH_HAS_HCD select USB help USB Touchscreen driver for: - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700) - PanJit TouchSet USB - 3M MicroTouch USB (EX II series) - ITM - some other eTurboTouch - Gunze AHL61 - DMC TSC-10/25 - IRTOUCHSYSTEMS/UNITOP - IdealTEK URTC1000 - GoTop Super_Q2/GogoPen/PenPower tablets - JASTEC USB Touch Controller/DigiTech DTR-02U - Zytronic controllers Have a look at for a usage description and the required user-space stuff. To compile this driver as a module, choose M here: the module will be called usbtouchscreen. config TOUCHSCREEN_MC13783 tristate "Freescale MC13783 touchscreen input driver" depends on MFD_MC13783 help Say Y here if you have an Freescale MC13783 PMIC on your board and want to use its touchscreen If unsure, say N. To compile this driver as a module, choose M here: the module will be called mc13783_ts. config TOUCHSCREEN_USB_EGALAX default y bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_PANJIT default y bool "PanJit device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_3M default y bool "3M/Microtouch EX II series device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_ITM default y bool "ITM device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_ETURBO default y bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_GUNZE default y bool "Gunze AHL61 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_DMC_TSC10 default y bool "DMC TSC-10/25 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_IRTOUCH default y bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_IDEALTEK default y bool "IdealTEK URTC1000 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_GENERAL_TOUCH default y bool "GeneralTouch Touchscreen device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_GOTOP default y bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_JASTEC default y bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_E2I default y bool "e2i Touchscreen controller (e.g. from Mimo 740)" depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_ZYTRONIC default y bool "Zytronic controller" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_ETT_TC5UH default y bool "ET&T TC5UH touchscreen controler support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_NEXIO default y bool "NEXIO/iNexio device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_TOUCHIT213 tristate "Sahara TouchIT-213 touchscreen" select SERIO help Say Y here if you have a Sahara TouchIT-213 Tablet PC. If unsure, say N. To compile this driver as a module, choose M here: the module will be called touchit213. config TOUCHSCREEN_TSC2007 tristate "TSC2007 based touchscreens" depends on I2C help Say Y here if you have a TSC2007 based touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called tsc2007. config TOUCHSCREEN_W90X900 tristate "W90P910 touchscreen driver" depends on HAVE_CLK help Say Y here if you have a W90P910 based touchscreen. To compile this driver as a module, choose M here: the module will be called w90p910_ts. config TOUCHSCREEN_PCAP tristate "Motorola PCAP touchscreen" depends on EZX_PCAP help Say Y here if you have a Motorola EZX telephone and want to enable support for the built-in touchscreen. To compile this driver as a module, choose M here: the module will be called pcap_ts. config TOUCHSCREEN_TPS6507X tristate "TPS6507x based touchscreens" depends on I2C help Say Y here if you have a TPS6507x based touchscreen controller. If unsure, say N. To compile this driver as a module, choose M here: the module will be called tps6507x_ts. endif