/* Copyright 2003 Tungsten Graphics, Inc., Cedar Park, Texas. * All Rights Reserved. * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the * "Software"), to deal in the Software without restriction, including * without limitation the rights to use, copy, modify, merge, publish, * distribute, sub license, and/or sell copies of the Software, and to * permit persons to whom the Software is furnished to do so, subject to * the following conditions: * * The above copyright notice and this permission notice (including the * next paragraph) shall be included in all copies or substantial portions * of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. * IN NO EVENT SHALL TUNGSTEN GRAPHICS AND/OR ITS SUPPLIERS BE LIABLE FOR * ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, * TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE * SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */ #ifndef _I915_REG_H_ #define _I915_REG_H_ /* * The Bridge device's PCI config space has information about the * fb aperture size and the amount of pre-reserved memory. */ #define INTEL_GMCH_CTRL 0x52 #define INTEL_GMCH_VGA_DISABLE (1 << 1) #define INTEL_GMCH_ENABLED 0x4 #define INTEL_GMCH_MEM_MASK 0x1 #define INTEL_GMCH_MEM_64M 0x1 #define INTEL_GMCH_MEM_128M 0 #define INTEL_GMCH_GMS_MASK (0xf << 4) #define INTEL_855_GMCH_GMS_DISABLED (0x0 << 4) #define INTEL_855_GMCH_GMS_STOLEN_1M (0x1 << 4) #define INTEL_855_GMCH_GMS_STOLEN_4M (0x2 << 4) #define INTEL_855_GMCH_GMS_STOLEN_8M (0x3 << 4) #define INTEL_855_GMCH_GMS_STOLEN_16M (0x4 << 4) #define INTEL_855_GMCH_GMS_STOLEN_32M (0x5 << 4) #define INTEL_915G_GMCH_GMS_STOLEN_48M (0x6 << 4) #define INTEL_915G_GMCH_GMS_STOLEN_64M (0x7 << 4) #define INTEL_GMCH_GMS_STOLEN_128M (0x8 << 4) #define INTEL_GMCH_GMS_STOLEN_256M (0x9 << 4) #define INTEL_GMCH_GMS_STOLEN_96M (0xa << 4) #define INTEL_GMCH_GMS_STOLEN_160M (0xb << 4) #define INTEL_GMCH_GMS_STOLEN_224M (0xc << 4) #define INTEL_GMCH_GMS_STOLEN_352M (0xd << 4) /* PCI config space */ #define HPLLCC 0xc0 /* 855 only */ #define GC_CLOCK_CONTROL_MASK (0xf << 0) #define GC_CLOCK_133_200 (0 << 0) #define GC_CLOCK_100_200 (1 << 0) #define GC_CLOCK_100_133 (2 << 0) #define GC_CLOCK_166_250 (3 << 0) #define GCFGC 0xf0 /* 915+ only */ #define GC_LOW_FREQUENCY_ENABLE (1 << 7) #define GC_DISPLAY_CLOCK_190_200_MHZ (0 << 4) #define GC_DISPLAY_CLOCK_333_MHZ (4 << 4) #define GC_DISPLAY_CLOCK_MASK (7 << 4) #define GM45_GC_RENDER_CLOCK_MASK (0xf << 0) #define GM45_GC_RENDER_CLOCK_266_MHZ (8 << 0) #define GM45_GC_RENDER_CLOCK_320_MHZ (9 << 0) #define GM45_GC_RENDER_CLOCK_400_MHZ (0xb << 0) #define GM45_GC_RENDER_CLOCK_533_MHZ (0xc << 0) #define I965_GC_RENDER_CLOCK_MASK (0xf << 0) #define I965_GC_RENDER_CLOCK_267_MHZ (2 << 0) #define I965_GC_RENDER_CLOCK_333_MHZ (3 << 0) #define I965_GC_RENDER_CLOCK_444_MHZ (4 << 0) #define I965_GC_RENDER_CLOCK_533_MHZ (5 << 0) #define I945_GC_RENDER_CLOCK_MASK (7 << 0) #define I945_GC_RENDER_CLOCK_166_MHZ (0 << 0) #define I945_GC_RENDER_CLOCK_200_MHZ (1 << 0) #define I945_GC_RENDER_CLOCK_250_MHZ (3 << 0) #define I945_GC_RENDER_CLOCK_400_MHZ (5 << 0) #define I915_GC_RENDER_CLOCK_MASK (7 << 0) #define I915_GC_RENDER_CLOCK_166_MHZ (0 << 0) #define I915_GC_RENDER_CLOCK_200_MHZ (1 << 0) #define I915_GC_RENDER_CLOCK_333_MHZ (4 << 0) #define LBB 0xf4 #define GDRST 0xc0 #define GDRST_FULL (0<<2) #define GDRST_RENDER (1<<2) #define GDRST_MEDIA (3<<2) /* VGA stuff */ #define VGA_ST01_MDA 0x3ba #define VGA_ST01_CGA 0x3da #define VGA_MSR_WRITE 0x3c2 #define VGA_MSR_READ 0x3cc #define VGA_MSR_MEM_EN (1<<1) #define VGA_MSR_CGA_MODE (1<<0) #define VGA_SR_INDEX 0x3c4 #define VGA_SR_DATA 0x3c5 #define VGA_AR_INDEX 0x3c0 #define VGA_AR_VID_EN (1<<5) #define VGA_AR_DATA_WRITE 0x3c0 #define VGA_AR_DATA_READ 0x3c1 #define VGA_GR_INDEX 0x3ce #define VGA_GR_DATA 0x3cf /* GR05 */ #define VGA_GR_MEM_READ_MODE_SHIFT 3 #define VGA_GR_MEM_READ_MODE_PLANE 1 /* GR06 */ #define VGA_GR_MEM_MODE_MASK 0xc #define VGA_GR_MEM_MODE_SHIFT 2 #define VGA_GR_MEM_A0000_AFFFF 0 #define VGA_GR_MEM_A0000_BFFFF 1 #define VGA_GR_MEM_B0000_B7FFF 2 #define VGA_GR_MEM_B0000_BFFFF 3 #define VGA_DACMASK 0x3c6 #define VGA_DACRX 0x3c7 #define VGA_DACWX 0x3c8 #define VGA_DACDATA 0x3c9 #define VGA_CR_INDEX_MDA 0x3b4 #define VGA_CR_DATA_MDA 0x3b5 #define VGA_CR_INDEX_CGA 0x3d4 #define VGA_CR_DATA_CGA 0x3d5 /* * Memory interface instructions used by the kernel */ #define MI_INSTR(opcode, flags) (((opcode) << 23) | (flags)) #define MI_NOOP MI_INSTR(0, 0) #define MI_USER_INTERRUPT MI_INSTR(0x02, 0) #define MI_WAIT_FOR_EVENT MI_INSTR(0x03, 0) #define MI_WAIT_FOR_PLANE_B_FLIP (1<<6) #define MI_WAIT_FOR_PLANE_A_FLIP (1<<2) #define MI_WAIT_FOR_PLANE_A_SCANLINES (1<<1) #define MI_FLUSH MI_INSTR(0x04, 0) #define MI_READ_FLUSH (1 << 0) #define MI_EXE_FLUSH (1 << 1) #define MI_NO_WRITE_FLUSH (1 << 2) #define MI_SCENE_COUNT (1 << 3) /* just increment scene count */ #define MI_END_SCENE (1 << 4) /* flush binner and incr scene count */ #define MI_BATCH_BUFFER_END MI_INSTR(0x0a, 0) #define MI_REPORT_HEAD MI_INSTR(0x07, 0) #define MI_LOAD_SCAN_LINES_INCL MI_INSTR(0x12, 0) #define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1) #define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */ #define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1) #define MI_STORE_DWORD_INDEX_SHIFT 2 #define MI_LOAD_REGISTER_IMM MI_INSTR(0x22, 1) #define MI_BATCH_BUFFER MI_INSTR(0x30, 1) #define MI_BATCH_NON_SECURE (1) #define MI_BATCH_NON_SECURE_I965 (1<<8) #define MI_BATCH_BUFFER_START MI_INSTR(0x31, 0) /* * 3D instructions used by the kernel */ #define GFX_INSTR(opcode, flags) ((0x3 << 29) | ((opcode) << 24) | (flags)) #define GFX_OP_RASTER_RULES ((0x3<<29)|(0x7<<24)) #define GFX_OP_SCISSOR ((0x3<<29)|(0x1c<<24)|(0x10<<19)) #define SC_UPDATE_SCISSOR (0x1<<1) #define SC_ENABLE_MASK (0x1<<0) #define SC_ENABLE (0x1<<0) #define GFX_OP_LOAD_INDIRECT ((0x3<<29)|(0x1d<<24)|(0x7<<16)) #define GFX_OP_SCISSOR_INFO ((0x3<<29)|(0x1d<<24)|(0x81<<16)|(0x1)) #define SCI_YMIN_MASK (0xffff<<16) #define SCI_XMIN_MASK (0xffff<<0) #define SCI_YMAX_MASK (0xffff<<16) #define SCI_XMAX_MASK (0xffff<<0) #define GFX_OP_SCISSOR_ENABLE ((0x3<<29)|(0x1c<<24)|(0x10<<19)) #define GFX_OP_SCISSOR_RECT ((0x3<<29)|(0x1d<<24)|(0x81<<16)|1) #define GFX_OP_COLOR_FACTOR ((0x3<<29)|(0x1d<<24)|(0x1<<16)|0x0) #define GFX_OP_STIPPLE ((0x3<<29)|(0x1d<<24)|(0x83<<16)) #define GFX_OP_MAP_INFO ((0x3<<29)|(0x1d<<24)|0x4) #define GFX_OP_DESTBUFFER_VARS ((0x3<<29)|(0x1d<<24)|(0x85<<16)|0x0) #define GFX_OP_DESTBUFFER_INFO ((0x3<<29)|(0x1d<<24)|(0x8e<<16)|1) #define GFX_OP_DRAWRECT_INFO ((0x3<<29)|(0x1d<<24)|(0x80<<16)|(0x3)) #define GFX_OP_DRAWRECT_INFO_I965 ((0x7900<<16)|0x2) #define SRC_COPY_BLT_CMD ((2<<29)|(0x43<<22)|4) #define XY_SRC_COPY_BLT_CMD ((2<<29)|(0x53<<22)|6) #define XY_MONO_SRC_COPY_IMM_BLT ((2<<29)|(0x71<<22)|5) #define XY_SRC_COPY_BLT_WRITE_ALPHA (1<<21) #define XY_SRC_COPY_BLT_WRITE_RGB (1<<20) #define BLT_DEPTH_8 (0<<24) #define BLT_DEPTH_16_565 (1<<24) #define BLT_DEPTH_16_1555 (2<<24) #define BLT_DEPTH_32 (3<<24) #define BLT_ROP_GXCOPY (0xcc<<16) #define XY_SRC_COPY_BLT_SRC_TILED (1<<15) /* 965+ only */ #define XY_SRC_COPY_BLT_DST_TILED (1<<11) /* 965+ only */ #define CMD_OP_DISPLAYBUFFER_INFO ((0x0<<29)|(0x14<<23)|2) #define ASYNC_FLIP (1<<22) #define DISPLAY_PLANE_A (0<<20) #define DISPLAY_PLANE_B (1<<20) /* * Fence registers */ #define FENCE_REG_830_0 0x2000 #define FENCE_REG_945_8 0x3000 #define I830_FENCE_START_MASK 0x07f80000 #define I830_FENCE_TILING_Y_SHIFT 12 #define I830_FENCE_SIZE_BITS(size) ((ffs((size) >> 19) - 1) << 8) #define I830_FENCE_PITCH_SHIFT 4 #define I830_FENCE_REG_VALID (1<<0) #define I915_FENCE_MAX_PITCH_VAL 0x10 #define I830_FENCE_MAX_PITCH_VAL 6 #define I830_FENCE_MAX_SIZE_VAL (1<<8) #define I915_FENCE_START_MASK 0x0ff00000 #define I915_FENCE_SIZE_BITS(size) ((ffs((size) >> 20) - 1) << 8) #define FENCE_REG_965_0 0x03000 #define I965_FENCE_PITCH_SHIFT 2 #define I965_FENCE_TILING_Y_SHIFT 1 #define I965_FENCE_REG_VALID (1<<0) #define I965_FENCE_MAX_PITCH_VAL 0x0400 /* * Instruction and interrupt control regs */ #define PGTBL_ER 0x02024 #define PRB0_TAIL 0x02030 #define PRB0_HEAD 0x02034 #define PRB0_START 0x02038 #define PRB0_CTL 0x0203c #define TAIL_ADDR 0x001FFFF8 #define HEAD_WRAP_COUNT 0xFFE00000 #define HEAD_WRAP_ONE 0x00200000 #define HEAD_ADDR 0x001FFFFC #define RING_NR_PAGES 0x001FF000 #define RING_REPORT_MASK 0x00000006 #define RING_REPORT_64K 0x00000002 #define RING_REPORT_128K 0x00000004 #define RING_NO_REPORT 0x00000000 #define RING_VALID_MASK 0x00000001 #define RING_VALID 0x00000001 #define RING_INVALID 0x00000000 #define PRB1_TAIL 0x02040 /* 915+ only */ #define PRB1_HEAD 0x02044 /* 915+ only */ #define PRB1_START 0x02048 /* 915+ only */ #define PRB1_CTL 0x0204c /* 915+ only */ #define IPEIR_I965 0x02064 #define IPEHR_I965 0x02068 #define INSTDONE_I965 0x0206c #define INSTPS 0x02070 /* 965+ only */ #define INSTDONE1 0x0207c /* 965+ only */ #define ACTHD_I965 0x02074 #define HWS_PGA 0x02080 #define HWS_ADDRESS_MASK 0xfffff000 #define HWS_START_ADDRESS_SHIFT 4 #define IPEIR 0x02088 #define IPEHR 0x0208c #define INSTDONE 0x02090 #define NOPID 0x02094 #define HWSTAM 0x02098 #define SCPD0 0x0209c /* 915+ only */ #define IER 0x020a0 #define IIR 0x020a4 #define IMR 0x020a8 #define ISR 0x020ac #define I915_PIPE_CONTROL_NOTIFY_INTERRUPT (1<<18) #define I915_DISPLAY_PORT_INTERRUPT (1<<17) #define I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT (1<<15) #define I915_GMCH_THERMAL_SENSOR_EVENT_INTERRUPT (1<<14) #define I915_HWB_OOM_INTERRUPT (1<<13) #define I915_SYNC_STATUS_INTERRUPT (1<<12) #define I915_DISPLAY_PLANE_A_FLIP_PENDING_INTERRUPT (1<<11) #define I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT (1<<10) #define I915_OVERLAY_PLANE_FLIP_PENDING_INTERRUPT (1<<9) #define I915_DISPLAY_PLANE_C_FLIP_PENDING_INTERRUPT (1<<8) #define I915_DISPLAY_PIPE_A_VBLANK_INTERRUPT (1<<7) #define I915_DISPLAY_PIPE_A_EVENT_INTERRUPT (1<<6) #define I915_DISPLAY_PIPE_B_VBLANK_INTERRUPT (1<<5) #define I915_DISPLAY_PIPE_B_EVENT_INTERRUPT (1<<4) #define I915_DEBUG_INTERRUPT (1<<2) #define I915_USER_INTERRUPT (1<<1) #define I915_ASLE_INTERRUPT (1<<0) #define EIR 0x020b0 #define EMR 0x020b4 #define ESR 0x020b8 #define GM45_ERROR_PAGE_TABLE (1<<5) #define GM45_ERROR_MEM_PRIV (1<<4) #define I915_ERROR_PAGE_TABLE (1<<4) #define GM45_ERROR_CP_PRIV (1<<3) #define I915_ERROR_MEMORY_REFRESH (1<<1) #define I915_ERROR_INSTRUCTION (1<<0) #define INSTPM 0x020c0 #define ACTHD 0x020c8 #define FW_BLC 0x020d8 #define FW_BLC2 0x020dc #define FW_BLC_SELF 0x020e0 /* 915+ only */ #define FW_BLC_SELF_EN (1<<15) #define MM_BURST_LENGTH 0x00700000 #define MM_FIFO_WATERMARK 0x0001F000 #define LM_BURST_LENGTH 0x00000700 #define LM_FIFO_WATERMARK 0x0000001F #define MI_ARB_STATE 0x020e4 /* 915+ only */ #define CACHE_MODE_0 0x02120 /* 915+ only */ #define CM0_MASK_SHIFT 16 #define CM0_IZ_OPT_DISABLE (1<<6) #define CM0_ZR_OPT_DISABLE (1<<5) #define CM0_DEPTH_EVICT_DISABLE (1<<4) #define CM0_COLOR_EVICT_DISABLE (1<<3) #define CM0_DEPTH_WRITE_DISABLE (1<<1) #define CM0_RC_OP_FLUSH_DISABLE (1<<0) #define GFX_FLSH_CNTL 0x02170 /* 915+ only */ /* * Framebuffer compression (915+ only) */ #define FBC_CFB_BASE 0x03200 /* 4k page aligned */ #define FBC_LL_BASE 0x03204 /* 4k page aligned */ #define FBC_CONTROL 0x03208 #define FBC_CTL_EN (1<<31) #define FBC_CTL_PERIODIC (1<<30) #define FBC_CTL_INTERVAL_SHIFT (16) #define FBC_CTL_UNCOMPRESSIBLE (1<<14) #define FBC_CTL_STRIDE_SHIFT (5) #define FBC_CTL_FENCENO (1<<0) #define FBC_COMMAND 0x0320c #define FBC_CMD_COMPRESS (1<<0) #define FBC_STATUS 0x03210 #define FBC_STAT_COMPRESSING (1<<31) #define FBC_STAT_COMPRESSED (1<<30) #define FBC_STAT_MODIFIED (1<<29) #define FBC_STAT_CURRENT_LINE (1<<0) #define FBC_CONTROL2 0x03214 #define FBC_CTL_FENCE_DBL (0<<4) #define FBC_CTL_IDLE_IMM (0<<2) #define FBC_CTL_IDLE_FULL (1<<2) #define FBC_CTL_IDLE_LINE (2<<2) #define FBC_CTL_IDLE_DEBUG (3<<2) #define FBC_CTL_CPU_FENCE (1<<1) #define FBC_CTL_PLANEA (0<<0) #define FBC_CTL_PLANEB (1<<0) #define FBC_FENCE_OFF 0x0321b #define FBC_TAG 0x03300 #define FBC_LL_SIZE (1536) /* Framebuffer compression for GM45+ */ #define DPFC_CB_BASE 0x3200 #define DPFC_CONTROL 0x3208 #define DPFC_CTL_EN (1<<31) #define DPFC_CTL_PLANEA (0<<30) #define DPFC_CTL_PLANEB (1<<30) #define DPFC_CTL_FENCE_EN (1<<29) #define DPFC_SR_EN (1<<10) #define DPFC_CTL_LIMIT_1X (0<<6) #define DPFC_CTL_LIMIT_2X (1<<6) #define DPFC_CTL_LIMIT_4X (2<<6) #define DPFC_RECOMP_CTL 0x320c #define DPFC_RECOMP_STALL_EN (1<<27) #define DPFC_RECOMP_STALL_WM_SHIFT (16) #define DPFC_RECOMP_STALL_WM_MASK (0x07ff0000) #define DPFC_RECOMP_TIMER_COUNT_SHIFT (0) #define DPFC_RECOMP_TIMER_COUNT_MASK (0x0000003f) #define DPFC_STATUS 0x3210 #define DPFC_INVAL_SEG_SHIFT (16) #define DPFC_INVAL_SEG_MASK (0x07ff0000) #define DPFC_COMP_SEG_SHIFT (0) #define DPFC_COMP_SEG_MASK (0x000003ff) #define DPFC_STATUS2 0x3214 #define DPFC_FENCE_YOFF 0x3218 #define DPFC_CHICKEN 0x3224 #define DPFC_HT_MODIFY (1<<31) /* * GPIO regs */ #define GPIOA 0x5010 #define GPIOB 0x5014 #define GPIOC 0x5018 #define GPIOD 0x501c #define GPIOE 0x5020 #define GPIOF 0x5024 #define GPIOG 0x5028 #define GPIOH 0x502c # define GPIO_CLOCK_DIR_MASK (1 << 0) # define GPIO_CLOCK_DIR_IN (0 << 1) # define GPIO_CLOCK_DIR_OUT (1 << 1) # define GPIO_CLOCK_VAL_MASK (1 << 2) # define GPIO_CLOCK_VAL_OUT (1 << 3) # define GPIO_CLOCK_VAL_IN (1 << 4) # define GPIO_CLOCK_PULLUP_DISABLE (1 << 5) # define GPIO_DATA_DIR_MASK (1 << 8) # define GPIO_DATA_DIR_IN (0 << 9) # define GPIO_DATA_DIR_OUT (1 << 9) # define GPIO_DATA_VAL_MASK (1 << 10) # define GPIO_DATA_VAL_OUT (1 << 11) # define GPIO_DATA_VAL_IN (1 << 12) # define GPIO_DATA_PULLUP_DISABLE (1 << 13) /* * Clock control & power management */ #define VGA0 0x6000 #define VGA1 0x6004 #define VGA_PD 0x6010 #define VGA0_PD_P2_DIV_4 (1 << 7) #define VGA0_PD_P1_DIV_2 (1 << 5) #define VGA0_PD_P1_SHIFT 0 #define VGA0_PD_P1_MASK (0x1f << 0) #define VGA1_PD_P2_DIV_4 (1 << 15) #define VGA1_PD_P1_DIV_2 (1 << 13) #define VGA1_PD_P1_SHIFT 8 #define VGA1_PD_P1_MASK (0x1f << 8) #define DPLL_A 0x06014 #define DPLL_B 0x06018 #define DPLL_VCO_ENABLE (1 << 31) #define DPLL_DVO_HIGH_SPEED (1 << 30) #define DPLL_SYNCLOCK_ENABLE (1 << 29) #define DPLL_VGA_MODE_DIS (1 << 28) #define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */ #define DPLLB_MODE_LVDS (2 << 26) /* i915 */ #define DPLL_MODE_MASK (3 << 26) #define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */ #define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */ #define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */ #define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */ #define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */ #define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */ #define DPLL_FPA01_P1_POST_DIV_MASK_IGD 0x00ff8000 /* IGD */ #define I915_FIFO_UNDERRUN_STATUS (1UL<<31) #define I915_CRC_ERROR_ENABLE (1UL<<29) #define I915_CRC_DONE_ENABLE (1UL<<28) #define I915_GMBUS_EVENT_ENABLE (1UL<<27) #define I915_VSYNC_INTERRUPT_ENABLE (1UL<<25) #define I915_DISPLAY_LINE_COMPARE_ENABLE (1UL<<24) #define I915_DPST_EVENT_ENABLE (1UL<<23) #define I915_LEGACY_BLC_EVENT_ENABLE (1UL<<22) #define I915_ODD_FIELD_INTERRUPT_ENABLE (1UL<<21) #define I915_EVEN_FIELD_INTERRUPT_ENABLE (1UL<<20) #define I915_START_VBLANK_INTERRUPT_ENABLE (1UL<<18) /* 965 or later */ #define I915_VBLANK_INTERRUPT_ENABLE (1UL<<17) #define I915_OVERLAY_UPDATED_ENABLE (1UL<<16) #define I915_CRC_ERROR_INTERRUPT_STATUS (1UL<<13) #define I915_CRC_DONE_INTERRUPT_STATUS (1UL<<12) #define I915_GMBUS_INTERRUPT_STATUS (1UL<<11) #define I915_VSYNC_INTERRUPT_STATUS (1UL<<9) #define I915_DISPLAY_LINE_COMPARE_STATUS (1UL<<8) #define I915_DPST_EVENT_STATUS (1UL<<7) #define I915_LEGACY_BLC_EVENT_STATUS (1UL<<6) #define I915_ODD_FIELD_INTERRUPT_STATUS (1UL<<5) #define I915_EVEN_FIELD_INTERRUPT_STATUS (1UL<<4) #define I915_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */ #define I915_VBLANK_INTERRUPT_STATUS (1UL<<1) #define I915_OVERLAY_UPDATED_STATUS (1UL<<0) #define SRX_INDEX 0x3c4 #define SRX_DATA 0x3c5 #define SR01 1 #define SR01_SCREEN_OFF (1<<5) #define PPCR 0x61204 #define PPCR_ON (1<<0) #define DVOB 0x61140 #define DVOB_ON (1<<31) #define DVOC 0x61160 #define DVOC_ON (1<<31) #define LVDS 0x61180 #define LVDS_ON (1<<31) #define ADPA 0x61100 #define ADPA_DPMS_MASK (~(3<<10)) #define ADPA_DPMS_ON (0<<10) #define ADPA_DPMS_SUSPEND (1<<10) #define ADPA_DPMS_STANDBY (2<<10) #define ADPA_DPMS_OFF (3<<10) #define RING_TAIL 0x00 #define TAIL_ADDR 0x001FFFF8 #define RING_HEAD 0x04 #define HEAD_WRAP_COUNT 0xFFE00000 #define HEAD_WRAP_ONE 0x00200000 #define HEAD_ADDR 0x001FFFFC #define RING_START 0x08 #define START_ADDR 0xFFFFF000 #define RING_LEN 0x0C #define RING_NR_PAGES 0x001FF000 #define RING_REPORT_MASK 0x00000006 #define RING_REPORT_64K 0x00000002 #define RING_REPORT_128K 0x00000004 #define RING_NO_REPORT 0x00000000 #define RING_VALID_MASK 0x00000001 #define RING_VALID 0x00000001 #define RING_INVALID 0x00000000 /* Scratch pad debug 0 reg: */ #define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000 /* * The i830 generation, in LVDS mode, defines P1 as the bit number set within * this field (only one bit may be set). */ #define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000 #define DPLL_FPA01_P1_POST_DIV_SHIFT 16 #define DPLL_FPA01_P1_POST_DIV_SHIFT_IGD 15 /* i830, required in DVO non-gang */ #define PLL_P2_DIVIDE_BY_4 (1 << 23) #define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */ #define PLL_REF_INPUT_DREFCLK (0 << 13) #define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */ #define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO TVCLKIN */ #define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13) #define PLL_REF_INPUT_MASK (3 << 13) #define PLL_LOAD_PULSE_PHASE_SHIFT 9 /* IGDNG */ # define PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT 9 # define PLL_REF_SDVO_HDMI_MULTIPLIER_MASK (7 << 9) # define PLL_REF_SDVO_HDMI_MULTIPLIER(x) (((x)-1) << 9) # define DPLL_FPA1_P1_POST_DIV_SHIFT 0 # define DPLL_FPA1_P1_POST_DIV_MASK 0xff /* * Parallel to Serial Load Pulse phase selection. * Selects the phase for the 10X DPLL clock for the PCIe * digital display port. The range is 4 to 13; 10 or more * is just a flip delay. The default is 6 */ #define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT) #define DISPLAY_RATE_SELECT_FPA1 (1 << 8) /* * SDVO multiplier for 945G/GM. Not used on 965. */ #define SDVO_MULTIPLIER_MASK 0x000000ff #define SDVO_MULTIPLIER_SHIFT_HIRES 4 #define SDVO_MULTIPLIER_SHIFT_VGA 0 #define DPLL_A_MD 0x0601c /* 965+ only */ /* * UDI pixel divider, controlling how many pixels are stuffed into a packet. * * Value is pixels minus 1. Must be set to 1 pixel for SDVO. */ #define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000 #define DPLL_MD_UDI_DIVIDER_SHIFT 24 /* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */ #define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000 #define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16 /* * SDVO/UDI pixel multiplier. * * SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus * clock rate is 10 times the DPLL clock. At low resolution/refresh rate * modes, the bus rate would be below the limits, so SDVO allows for stuffing * dummy bytes in the datastream at an increased clock rate, with both sides of * the link knowing how many bytes are fill. * * So, for a mode with a dotclock of 65Mhz, we would want to double the clock * rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be * set to 130Mhz, and the SDVO multiplier set to 2x in this register and * through an SDVO command. * * This register field has values of multiplication factor minus 1, with * a maximum multiplier of 5 for SDVO. */ #define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00 #define DPLL_MD_UDI_MULTIPLIER_SHIFT 8 /* * SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK. * This best be set to the default value (3) or the CRT won't work. No, * I don't entirely understand what this does... */ #define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f #define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0 #define DPLL_B_MD 0x06020 /* 965+ only */ #define FPA0 0x06040 #define FPA1 0x06044 #define FPB0 0x06048 #define FPB1 0x0604c #define FP_N_DIV_MASK 0x003f0000 #define FP_N_IGD_DIV_MASK 0x00ff0000 #define FP_N_DIV_SHIFT 16 #define FP_M1_DIV_MASK 0x00003f00 #define FP_M1_DIV_SHIFT 8 #define FP_M2_DIV_MASK 0x0000003f #define FP_M2_IGD_DIV_MASK 0x000000ff #define FP_M2_DIV_SHIFT 0 #define DPLL_TEST 0x606c #define DPLLB_TEST_SDVO_DIV_1 (0 << 22) #define DPLLB_TEST_SDVO_DIV_2 (1 << 22) #define DPLLB_TEST_SDVO_DIV_4 (2 << 22) #define DPLLB_TEST_SDVO_DIV_MASK (3 << 22) #define DPLLB_TEST_N_BYPASS (1 << 19) #define DPLLB_TEST_M_BYPASS (1 << 18) #define DPLLB_INPUT_BUFFER_ENABLE (1 << 16) #define DPLLA_TEST_N_BYPASS (1 << 3) #define DPLLA_TEST_M_BYPASS (1 << 2) #define DPLLA_INPUT_BUFFER_ENABLE (1 << 0) #define D_STATE 0x6104 #define DSTATE_PLL_D3_OFF (1<<3) #define DSTATE_GFX_CLOCK_GATING (1<<1) #define DSTATE_DOT_CLOCK_GATING (1<<0) #define DSPCLK_GATE_D 0x6200 # define DPUNIT_B_CLOCK_GATE_DISABLE (1 << 30) /* 965 */ # define VSUNIT_CLOCK_GATE_DISABLE (1 << 29) /* 965 */ # define VRHUNIT_CLOCK_GATE_DISABLE (1 << 28) /* 965 */ # define VRDUNIT_CLOCK_GATE_DISABLE (1 << 27) /* 965 */ # define AUDUNIT_CLOCK_GATE_DISABLE (1 << 26) /* 965 */ # define DPUNIT_A_CLOCK_GATE_DISABLE (1 << 25) /* 965 */ # define DPCUNIT_CLOCK_GATE_DISABLE (1 << 24) /* 965 */ # define TVRUNIT_CLOCK_GATE_DISABLE (1 << 23) /* 915-945 */ # define TVCUNIT_CLOCK_GATE_DISABLE (1 << 22) /* 915-945 */ # define TVFUNIT_CLOCK_GATE_DISABLE (1 << 21) /* 915-945 */ # define TVEUNIT_CLOCK_GATE_DISABLE (1 << 20) /* 915-945 */ # define DVSUNIT_CLOCK_GATE_DISABLE (1 << 19) /* 915-945 */ # define DSSUNIT_CLOCK_GATE_DISABLE (1 << 18) /* 915-945 */ # define DDBUNIT_CLOCK_GATE_DISABLE (1 << 17) /* 915-945 */ # define DPRUNIT_CLOCK_GATE_DISABLE (1 << 16) /* 915-945 */ # define DPFUNIT_CLOCK_GATE_DISABLE (1 << 15) /* 915-945 */ # define DPBMUNIT_CLOCK_GATE_DISABLE (1 << 14) /* 915-945 */ # define DPLSUNIT_CLOCK_GATE_DISABLE (1 << 13) /* 915-945 */ # define DPLUNIT_CLOCK_GATE_DISABLE (1 << 12) /* 915-945 */ # define DPOUNIT_CLOCK_GATE_DISABLE (1 << 11) # define DPBUNIT_CLOCK_GATE_DISABLE (1 << 10) # define DCUNIT_CLOCK_GATE_DISABLE (1 << 9) # define DPUNIT_CLOCK_GATE_DISABLE (1 << 8) # define VRUNIT_CLOCK_GATE_DISABLE (1 << 7) /* 915+: reserved */ # define OVHUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 830-865 */ # define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 915-945 */ # define OVFUNIT_CLOCK_GATE_DISABLE (1 << 5) # define OVBUNIT_CLOCK_GATE_DISABLE (1 << 4) /** * This bit must be set on the 830 to prevent hangs when turning off the * overlay scaler. */ # define OVRUNIT_CLOCK_GATE_DISABLE (1 << 3) # define OVCUNIT_CLOCK_GATE_DISABLE (1 << 2) # define OVUUNIT_CLOCK_GATE_DISABLE (1 << 1) # define ZVUNIT_CLOCK_GATE_DISABLE (1 << 0) /* 830 */ # define OVLUNIT_CLOCK_GATE_DISABLE (1 << 0) /* 845,865 */ #define RENCLK_GATE_D1 0x6204 # define BLITTER_CLOCK_GATE_DISABLE (1 << 13) /* 945GM only */ # define MPEG_CLOCK_GATE_DISABLE (1 << 12) /* 945GM only */ # define PC_FE_CLOCK_GATE_DISABLE (1 << 11) # define PC_BE_CLOCK_GATE_DISABLE (1 << 10) # define WINDOWER_CLOCK_GATE_DISABLE (1 << 9) # define INTERPOLATOR_CLOCK_GATE_DISABLE (1 << 8) # define COLOR_CALCULATOR_CLOCK_GATE_DISABLE (1 << 7) # define MOTION_COMP_CLOCK_GATE_DISABLE (1 << 6) # define MAG_CLOCK_GATE_DISABLE (1 << 5) /** This bit must be unset on 855,865 */ # define MECI_CLOCK_GATE_DISABLE (1 << 4) # define DCMP_CLOCK_GATE_DISABLE (1 << 3) # define MEC_CLOCK_GATE_DISABLE (1 << 2) # define MECO_CLOCK_GATE_DISABLE (1 << 1) /** This bit must be set on 855,865. */ # define SV_CLOCK_GATE_DISABLE (1 << 0) # define I915_MPEG_CLOCK_GATE_DISABLE (1 << 16) # define I915_VLD_IP_PR_CLOCK_GATE_DISABLE (1 << 15) # define I915_MOTION_COMP_CLOCK_GATE_DISABLE (1 << 14) # define I915_BD_BF_CLOCK_GATE_DISABLE (1 << 13) # define I915_SF_SE_CLOCK_GATE_DISABLE (1 << 12) # define I915_WM_CLOCK_GATE_DISABLE (1 << 11) # define I915_IZ_CLOCK_GATE_DISABLE (1 << 10) # define I915_PI_CLOCK_GATE_DISABLE (1 << 9) # define I915_DI_CLOCK_GATE_DISABLE (1 << 8) # define I915_SH_SV_CLOCK_GATE_DISABLE (1 << 7) # define I915_PL_DG_QC_FT_CLOCK_GATE_DISABLE (1 << 6) # define I915_SC_CLOCK_GATE_DISABLE (1 << 5) # define I915_FL_CLOCK_GATE_DISABLE (1 << 4) # define I915_DM_CLOCK_GATE_DISABLE (1 << 3) # define I915_PS_CLOCK_GATE_DISABLE (1 << 2) # define I915_CC_CLOCK_GATE_DISABLE (1 << 1) # define I915_BY_CLOCK_GATE_DISABLE (1 << 0) # define I965_RCZ_CLOCK_GATE_DISABLE (1 << 30) /** This bit must always be set on 965G/965GM */ # define I965_RCC_CLOCK_GATE_DISABLE (1 << 29) # define I965_RCPB_CLOCK_GATE_DISABLE (1 << 28) # define I965_DAP_CLOCK_GATE_DISABLE (1 << 27) # define I965_ROC_CLOCK_GATE_DISABLE (1 << 26) # define I965_GW_CLOCK_GATE_DISABLE (1 << 25) # define I965_TD_CLOCK_GATE_DISABLE (1 << 24) /** This bit must always be set on 965G */ # define I965_ISC_CLOCK_GATE_DISABLE (1 << 23) # define I965_IC_CLOCK_GATE_DISABLE (1 << 22) # define I965_EU_CLOCK_GATE_DISABLE (1 << 21) # define I965_IF_CLOCK_GATE_DISABLE (1 << 20) # define I965_TC_CLOCK_GATE_DISABLE (1 << 19) # define I965_SO_CLOCK_GATE_DISABLE (1 << 17) # define I965_FBC_CLOCK_GATE_DISABLE (1 << 16) # define I965_MARI_CLOCK_GATE_DISABLE (1 << 15) # define I965_MASF_CLOCK_GATE_DISABLE (1 << 14) # define I965_MAWB_CLOCK_GATE_DISABLE (1 << 13) # define I965_EM_CLOCK_GATE_DISABLE (1 << 12) # define I965_UC_CLOCK_GATE_DISABLE (1 << 11) # define I965_SI_CLOCK_GATE_DISABLE (1 << 6) # define I965_MT_CLOCK_GATE_DISABLE (1 << 5) # define I965_PL_CLOCK_GATE_DISABLE (1 << 4) # define I965_DG_CLOCK_GATE_DISABLE (1 << 3) # define I965_QC_CLOCK_GATE_DISABLE (1 << 2) # define I965_FT_CLOCK_GATE_DISABLE (1 << 1) # define I965_DM_CLOCK_GATE_DISABLE (1 << 0) #define RENCLK_GATE_D2 0x6208 #define VF_UNIT_CLOCK_GATE_DISABLE (1 << 9) #define GS_UNIT_CLOCK_GATE_DISABLE (1 << 7) #define CL_UNIT_CLOCK_GATE_DISABLE (1 << 6) #define RAMCLK_GATE_D 0x6210 /* CRL only */ #define DEUC 0x6214 /* CRL only */ /* * Palette regs */ #define PALETTE_A 0x0a000 #define PALETTE_B 0x0a800 /* MCH MMIO space */ /* * MCHBAR mirror. * * This mirrors the MCHBAR MMIO space whose location is determined by * device 0 function 0's pci config register 0x44 or 0x48 and matches it in * every way. It is not accessible from the CP register read instructions. * */ #define MCHBAR_MIRROR_BASE 0x10000 /** 915-945 and GM965 MCH register controlling DRAM channel access */ #define DCC 0x10200 #define DCC_ADDRESSING_MODE_SINGLE_CHANNEL (0 << 0) #define DCC_ADDRESSING_MODE_DUAL_CHANNEL_ASYMMETRIC (1 << 0) #define DCC_ADDRESSING_MODE_DUAL_CHANNEL_INTERLEAVED (2 << 0) #define DCC_ADDRESSING_MODE_MASK (3 << 0) #define DCC_CHANNEL_XOR_DISABLE (1 << 10) #define DCC_CHANNEL_XOR_BIT_17 (1 << 9) /** 965 MCH register controlling DRAM channel configuration */ #define C0DRB3 0x10206 #define C1DRB3 0x10606 /* Clocking configuration register */ #define CLKCFG 0x10c00 #define CLKCFG_FSB_400 (5 << 0) /* hrawclk 100 */ #define CLKCFG_FSB_533 (1 << 0) /* hrawclk 133 */ #define CLKCFG_FSB_667 (3 << 0) /* hrawclk 166 */ #define CLKCFG_FSB_800 (2 << 0) /* hrawclk 200 */ #define CLKCFG_FSB_1067 (6 << 0) /* hrawclk 266 */ #define CLKCFG_FSB_1333 (7 << 0) /* hrawclk 333 */ /* Note, below two are guess */ #define CLKCFG_FSB_1600 (4 << 0) /* hrawclk 400 */ #define CLKCFG_FSB_1600_ALT (0 << 0) /* hrawclk 400 */ #define CLKCFG_FSB_MASK (7 << 0) #define CLKCFG_MEM_533 (1 << 4) #define CLKCFG_MEM_667 (2 << 4) #define CLKCFG_MEM_800 (3 << 4) #define CLKCFG_MEM_MASK (7 << 4) /** GM965 GM45 render standby register */ #define MCHBAR_RENDER_STANDBY 0x111B8 #define PEG_BAND_GAP_DATA 0x14d68 /* * Overlay regs */ #define OVADD 0x30000 #define DOVSTA 0x30008 #define OC_BUF (0x3<<20) #define OGAMC5 0x30010 #define OGAMC4 0x30014 #define OGAMC3 0x30018 #define OGAMC2 0x3001c #define OGAMC1 0x30020 #define OGAMC0 0x30024 /* * Display engine regs */ /* Pipe A timing regs */ #define HTOTAL_A 0x60000 #define HBLANK_A 0x60004 #define HSYNC_A 0x60008 #define VTOTAL_A 0x6000c #define VBLANK_A 0x60010 #define VSYNC_A 0x60014 #define PIPEASRC 0x6001c #define BCLRPAT_A 0x60020 /* Pipe B timing regs */ #define HTOTAL_B 0x61000 #define HBLANK_B 0x61004 #define HSYNC_B 0x61008 #define VTOTAL_B 0x6100c #define VBLANK_B 0x61010 #define VSYNC_B 0x61014 #define PIPEBSRC 0x6101c #define BCLRPAT_B 0x61020 /* VGA port control */ #define ADPA 0x61100 #define ADPA_DAC_ENABLE (1<<31) #define ADPA_DAC_DISABLE 0 #define ADPA_PIPE_SELECT_MASK (1<<30) #define ADPA_PIPE_A_SELECT 0 #define ADPA_PIPE_B_SELECT (1<<30) #define ADPA_USE_VGA_HVPOLARITY (1<<15) #define ADPA_SETS_HVPOLARITY 0 #define ADPA_VSYNC_CNTL_DISABLE (1<<11) #define ADPA_VSYNC_CNTL_ENABLE 0 #define ADPA_HSYNC_CNTL_DISABLE (1<<10) #define ADPA_HSYNC_CNTL_ENABLE 0 #define ADPA_VSYNC_ACTIVE_HIGH (1<<4) #define ADPA_VSYNC_ACTIVE_LOW 0 #define ADPA_HSYNC_ACTIVE_HIGH (1<<3) #define ADPA_HSYNC_ACTIVE_LOW 0 #define ADPA_DPMS_MASK (~(3<<10)) #define ADPA_DPMS_ON (0<<10) #define ADPA_DPMS_SUSPEND (1<<10) #define ADPA_DPMS_STANDBY (2<<10) #define ADPA_DPMS_OFF (3<<10) /* Hotplug control (945+ only) */ #define PORT_HOTPLUG_EN 0x61110 #define HDMIB_HOTPLUG_INT_EN (1 << 29) #define DPB_HOTPLUG_INT_EN (1 << 29) #define HDMIC_HOTPLUG_INT_EN (1 << 28) #define DPC_HOTPLUG_INT_EN (1 << 28) #define HDMID_HOTPLUG_INT_EN (1 << 27) #define DPD_HOTPLUG_INT_EN (1 << 27) #define SDVOB_HOTPLUG_INT_EN (1 << 26) #define SDVOC_HOTPLUG_INT_EN (1 << 25) #define TV_HOTPLUG_INT_EN (1 << 18) #define CRT_EOS_INT_EN (1 << 10) #define CRT_HOTPLUG_INT_EN (1 << 9) #define CRT_HOTPLUG_FORCE_DETECT (1 << 3) #define CRT_HOTPLUG_ACTIVATION_PERIOD_32 (0 << 8) /* must use period 64 on GM45 according to docs */ #define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8) #define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7) #define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7) #define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5) #define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5) #define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5) #define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5) #define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5) #define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4) #define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4) #define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2) #define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2) #define CRT_HOTPLUG_MASK (0x3fc) /* Bits 9-2 */ #define CRT_FORCE_HOTPLUG_MASK 0xfffffe1f #define HOTPLUG_EN_MASK (HDMIB_HOTPLUG_INT_EN | \ HDMIC_HOTPLUG_INT_EN | \ HDMID_HOTPLUG_INT_EN | \ SDVOB_HOTPLUG_INT_EN | \ SDVOC_HOTPLUG_INT_EN | \ TV_HOTPLUG_INT_EN | \ CRT_HOTPLUG_INT_EN) #define PORT_HOTPLUG_STAT 0x61114 #define HDMIB_HOTPLUG_INT_STATUS (1 << 29) #define DPB_HOTPLUG_INT_STATUS (1 << 29) #define HDMIC_HOTPLUG_INT_STATUS (1 << 28) #define DPC_HOTPLUG_INT_STATUS (1 << 28) #define HDMID_HOTPLUG_INT_STATUS (1 << 27) #define DPD_HOTPLUG_INT_STATUS (1 << 27) #define CRT_EOS_INT_STATUS (1 << 12) #define CRT_HOTPLUG_INT_STATUS (1 << 11) #define TV_HOTPLUG_INT_STATUS (1 << 10) #define CRT_HOTPLUG_MONITOR_MASK (3 << 8) #define CRT_HOTPLUG_MONITOR_COLOR (3 << 8) #define CRT_HOTPLUG_MONITOR_MONO (2 << 8) #define CRT_HOTPLUG_MONITOR_NONE (0 << 8) #define SDVOC_HOTPLUG_INT_STATUS (1 << 7) #define SDVOB_HOTPLUG_INT_STATUS (1 << 6) /* SDVO port control */ #define SDVOB 0x61140 #define SDVOC 0x61160 #define SDVO_ENABLE (1 << 31) #define SDVO_PIPE_B_SELECT (1 << 30) #define SDVO_STALL_SELECT (1 << 29) #define SDVO_INTERRUPT_ENABLE (1 << 26) /** * 915G/GM SDVO pixel multiplier. * * Programmed value is multiplier - 1, up to 5x. * * \sa DPLL_MD_UDI_MULTIPLIER_MASK */ #define SDVO_PORT_MULTIPLY_MASK (7 << 23) #define SDVO_PORT_MULTIPLY_SHIFT 23 #define SDVO_PHASE_SELECT_MASK (15 << 19) #define SDVO_PHASE_SELECT_DEFAULT (6 << 19) #define SDVO_CLOCK_OUTPUT_INVERT (1 << 18) #define SDVOC_GANG_MODE (1 << 16) #define SDVO_ENCODING_SDVO (0x0 << 10) #define SDVO_ENCODING_HDMI (0x2 << 10) /** Requird for HDMI operation */ #define SDVO_NULL_PACKETS_DURING_VSYNC (1 << 9) #define SDVO_BORDER_ENABLE (1 << 7) #define SDVO_AUDIO_ENABLE (1 << 6) /** New with 965, default is to be set */ #define SDVO_VSYNC_ACTIVE_HIGH (1 << 4) /** New with 965, default is to be set */ #define SDVO_HSYNC_ACTIVE_HIGH (1 << 3) #define SDVOB_PCIE_CONCURRENCY (1 << 3) #define SDVO_DETECTED (1 << 2) /* Bits to be preserved when writing */ #define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14) | (1 << 26)) #define SDVOC_PRESERVE_MASK ((1 << 17) | (1 << 26)) /* DVO port control */ #define DVOA 0x61120 #define DVOB 0x61140 #define DVOC 0x61160 #define DVO_ENABLE (1 << 31) #define DVO_PIPE_B_SELECT (1 << 30) #define DVO_PIPE_STALL_UNUSED (0 << 28) #define DVO_PIPE_STALL (1 << 28) #define DVO_PIPE_STALL_TV (2 << 28) #define DVO_PIPE_STALL_MASK (3 << 28) #define DVO_USE_VGA_SYNC (1 << 15) #define DVO_DATA_ORDER_I740 (0 << 14) #define DVO_DATA_ORDER_FP (1 << 14) #define DVO_VSYNC_DISABLE (1 << 11) #define DVO_HSYNC_DISABLE (1 << 10) #define DVO_VSYNC_TRISTATE (1 << 9) #define DVO_HSYNC_TRISTATE (1 << 8) #define DVO_BORDER_ENABLE (1 << 7) #define DVO_DATA_ORDER_GBRG (1 << 6) #define DVO_DATA_ORDER_RGGB (0 << 6) #define DVO_DATA_ORDER_GBRG_ERRATA (0 << 6) #define DVO_DATA_ORDER_RGGB_ERRATA (1 << 6) #define DVO_VSYNC_ACTIVE_HIGH (1 << 4) #define DVO_HSYNC_ACTIVE_HIGH (1 << 3) #define DVO_BLANK_ACTIVE_HIGH (1 << 2) #define DVO_OUTPUT_CSTATE_PIXELS (1 << 1) /* SDG only */ #define DVO_OUTPUT_SOURCE_SIZE_PIXELS (1 << 0) /* SDG only */ #define DVO_PRESERVE_MASK (0x7<<24) #define DVOA_SRCDIM 0x61124 #define DVOB_SRCDIM 0x61144 #define DVOC_SRCDIM 0x61164 #define DVO_SRCDIM_HORIZONTAL_SHIFT 12 #define DVO_SRCDIM_VERTICAL_SHIFT 0 /* LVDS port control */ #define LVDS 0x61180 /* * Enables the LVDS port. This bit must be set before DPLLs are enabled, as * the DPLL semantics change when the LVDS is assigned to that pipe. */ #define LVDS_PORT_EN (1 << 31) /* Selects pipe B for LVDS data. Must be set on pre-965. */ #define LVDS_PIPEB_SELECT (1 << 30) /* Enable border for unscaled (or aspect-scaled) display */ #define LVDS_BORDER_ENABLE (1 << 15) /* * Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per * pixel. */ #define LVDS_A0A2_CLKA_POWER_MASK (3 << 8) #define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8) #define LVDS_A0A2_CLKA_POWER_UP (3 << 8) /* * Controls the A3 data pair, which contains the additional LSBs for 24 bit * mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be * on. */ #define LVDS_A3_POWER_MASK (3 << 6) #define LVDS_A3_POWER_DOWN (0 << 6) #define LVDS_A3_POWER_UP (3 << 6) /* * Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP * is set. */ #define LVDS_CLKB_POWER_MASK (3 << 4) #define LVDS_CLKB_POWER_DOWN (0 << 4) #define LVDS_CLKB_POWER_UP (3 << 4) /* * Controls the B0-B3 data pairs. This must be set to match the DPLL p2 * setting for whether we are in dual-channel mode. The B3 pair will * additionally only be powered up when LVDS_A3_POWER_UP is set. */ #define LVDS_B0B3_POWER_MASK (3 << 2) #define LVDS_B0B3_POWER_DOWN (0 << 2) #define LVDS_B0B3_POWER_UP (3 << 2) /* Panel power sequencing */ #define PP_STATUS 0x61200 #define PP_ON (1 << 31) /* * Indicates that all dependencies of the panel are on: * * - PLL enabled * - pipe enabled * - LVDS/DVOB/DVOC on */ #define PP_READY (1 << 30) #define PP_SEQUENCE_NONE (0 << 28) #define PP_SEQUENCE_ON (1 << 28) #define PP_SEQUENCE_OFF (2 << 28) #define PP_SEQUENCE_MASK 0x30000000 #define PP_CONTROL 0x61204 #define POWER_TARGET_ON (1 << 0) #define PP_ON_DELAYS 0x61208 #define PP_OFF_DELAYS 0x6120c #define PP_DIVISOR 0x61210 /* Panel fitting */ #define PFIT_CONTROL 0x61230 #define PFIT_ENABLE (1 << 31) #define PFIT_PIPE_MASK (3 << 29) #define PFIT_PIPE_SHIFT 29 #define VERT_INTERP_DISABLE (0 << 10) #define VERT_INTERP_BILINEAR (1 << 10) #define VERT_INTERP_MASK (3 << 10) #define VERT_AUTO_SCALE (1 << 9) #define HORIZ_INTERP_DISABLE (0 << 6) #define HORIZ_INTERP_BILINEAR (1 << 6) #define HORIZ_INTERP_MASK (3 << 6) #define HORIZ_AUTO_SCALE (1 << 5) #define PANEL_8TO6_DITHER_ENABLE (1 << 3) #define PFIT_FILTER_FUZZY (0 << 24) #define PFIT_SCALING_AUTO (0 << 26) #define PFIT_SCALING_PROGRAMMED (1 << 26) #define PFIT_SCALING_PILLAR (2 << 26) #define PFIT_SCALING_LETTER (3 << 26) #define PFIT_PGM_RATIOS 0x61234 #define PFIT_VERT_SCALE_MASK 0xfff00000 #define PFIT_HORIZ_SCALE_MASK 0x0000fff0 /* Pre-965 */ #define PFIT_VERT_SCALE_SHIFT 20 #define PFIT_VERT_SCALE_MASK 0xfff00000 #define PFIT_HORIZ_SCALE_SHIFT 4 #define PFIT_HORIZ_SCALE_MASK 0x0000fff0 /* 965+ */ #define PFIT_VERT_SCALE_SHIFT_965 16 #define PFIT_VERT_SCALE_MASK_965 0x1fff0000 #define PFIT_HORIZ_SCALE_SHIFT_965 0 #define PFIT_HORIZ_SCALE_MASK_965 0x00001fff #define PFIT_AUTO_RATIOS 0x61238 /* Backlight control */ #define BLC_PWM_CTL 0x61254 #define BACKLIGHT_MODULATION_FREQ_SHIFT (17) #define BLC_PWM_CTL2 0x61250 /* 965+ only */ #define BLM_COMBINATION_MODE (1 << 30) /* * This is the most significant 15 bits of the number of backlight cycles in a * complete cycle of the modulated backlight control. * * The actual value is this field multiplied by two. */ #define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17) #define BLM_LEGACY_MODE (1 << 16) /* * This is the number of cycles out of the backlight modulation cycle for which * the backlight is on. * * This field must be no greater than the number of cycles in the complete * backlight modulation cycle. */ #define BACKLIGHT_DUTY_CYCLE_SHIFT (0) #define BACKLIGHT_DUTY_CYCLE_MASK (0xffff) #define BLC_HIST_CTL 0x61260 /* TV port control */ #define TV_CTL 0x68000 /** Enables the TV encoder */ # define TV_ENC_ENABLE (1 << 31) /** Sources the TV encoder input from pipe B instead of A. */ # define TV_ENC_PIPEB_SELECT (1 << 30) /** Outputs composite video (DAC A only) */ # define TV_ENC_OUTPUT_COMPOSITE (0 << 28) /** Outputs SVideo video (DAC B/C) */ # define TV_ENC_OUTPUT_SVIDEO (1 << 28) /** Outputs Component video (DAC A/B/C) */ # define TV_ENC_OUTPUT_COMPONENT (2 << 28) /** Outputs Composite and SVideo (DAC A/B/C) */ # define TV_ENC_OUTPUT_SVIDEO_COMPOSITE (3 << 28) # define TV_TRILEVEL_SYNC (1 << 21) /** Enables slow sync generation (945GM only) */ # define TV_SLOW_SYNC (1 << 20) /** Selects 4x oversampling for 480i and 576p */ # define TV_OVERSAMPLE_4X (0 << 18) /** Selects 2x oversampling for 720p and 1080i */ # define TV_OVERSAMPLE_2X (1 << 18) /** Selects no oversampling for 1080p */ # define TV_OVERSAMPLE_NONE (2 << 18) /** Selects 8x oversampling */ # define TV_OVERSAMPLE_8X (3 << 18) /** Selects progressive mode rather than interlaced */ # define TV_PROGRESSIVE (1 << 17) /** Sets the colorburst to PAL mode. Required for non-M PAL modes. */ # define TV_PAL_BURST (1 << 16) /** Field for setting delay of Y compared to C */ # define TV_YC_SKEW_MASK (7 << 12) /** Enables a fix for 480p/576p standard definition modes on the 915GM only */ # define TV_ENC_SDP_FIX (1 << 11) /** * Enables a fix for the 915GM only. * * Not sure what it does. */ # define TV_ENC_C0_FIX (1 << 10) /** Bits that must be preserved by software */ # define TV_CTL_SAVE ((1 << 11) | (3 << 9) | (7 << 6) | 0xf) # define TV_FUSE_STATE_MASK (3 << 4) /** Read-only state that reports all features enabled */ # define TV_FUSE_STATE_ENABLED (0 << 4) /** Read-only state that reports that Macrovision is disabled in hardware*/ # define TV_FUSE_STATE_NO_MACROVISION (1 << 4) /** Read-only state that reports that TV-out is disabled in hardware. */ # define TV_FUSE_STATE_DISABLED (2 << 4) /** Normal operation */ # define TV_TEST_MODE_NORMAL (0 << 0) /** Encoder test pattern 1 - combo pattern */ # define TV_TEST_MODE_PATTERN_1 (1 << 0) /** Encoder test pattern 2 - full screen vertical 75% color bars */ # define TV_TEST_MODE_PATTERN_2 (2 << 0) /** Encoder test pattern 3 - full screen horizontal 75% color bars */ # define TV_TEST_MODE_PATTERN_3 (3 << 0) /** Encoder test pattern 4 - random noise */ # define TV_TEST_MODE_PATTERN_4 (4 << 0) /** Encoder test pattern 5 - linear color ramps */ # define TV_TEST_MODE_PATTERN_5 (5 << 0) /** * This test mode forces the DACs to 50% of full output. * * This is used for load detection in combination with TVDAC_SENSE_MASK */ # define TV_TEST_MODE_MONITOR_DETECT (7 << 0) # define TV_TEST_MODE_MASK (7 << 0) #define TV_DAC 0x68004 /** * Reports that DAC state change logic has reported change (RO). * * This gets cleared when TV_DAC_STATE_EN is cleared */ # define TVDAC_STATE_CHG (1 << 31) # define TVDAC_SENSE_MASK (7 << 28) /** Reports that DAC A voltage is above the detect threshold */ # define TVDAC_A_SENSE (1 << 30) /** Reports that DAC B voltage is above the detect threshold */ # define TVDAC_B_SENSE (1 << 29) /** Reports that DAC C voltage is above the detect threshold */ # define TVDAC_C_SENSE (1 << 28) /** * Enables DAC state detection logic, for load-based TV detection. * * The PLL of the chosen pipe (in TV_CTL) must be running, and the encoder set * to off, for load detection to work. */ # define TVDAC_STATE_CHG_EN (1 << 27) /** Sets the DAC A sense value to high */ # define TVDAC_A_SENSE_CTL (1 << 26) /** Sets the DAC B sense value to high */ # define TVDAC_B_SENSE_CTL (1 << 25) /** Sets the DAC C sense value to high */ # define TVDAC_C_SENSE_CTL (1 << 24) /** Overrides the ENC_ENABLE and DAC voltage levels */ # define DAC_CTL_OVERRIDE (1 << 7) /** Sets the slew rate. Must be preserved in software */ # define ENC_TVDAC_SLEW_FAST (1 << 6) # define DAC_A_1_3_V (0 << 4) # define DAC_A_1_1_V (1 << 4) # define DAC_A_0_7_V (2 << 4) # define DAC_A_MASK (3 << 4) # define DAC_B_1_3_V (0 << 2) # define DAC_B_1_1_V (1 << 2) # define DAC_B_0_7_V (2 << 2) # define DAC_B_MASK (3 << 2) # define DAC_C_1_3_V (0 << 0) # define DAC_C_1_1_V (1 << 0) # define DAC_C_0_7_V (2 << 0) # define DAC_C_MASK (3 << 0) /** * CSC coefficients are stored in a floating point format with 9 bits of * mantissa and 2 or 3 bits of exponent. The exponent is represented as 2**-n, * where 2-bit exponents are unsigned n, and 3-bit exponents are signed n with * -1 (0x3) being the only legal negative value. */ #define TV_CSC_Y 0x68010 # define TV_RY_MASK 0x07ff0000 # define TV_RY_SHIFT 16 # define TV_GY_MASK 0x00000fff # define TV_GY_SHIFT 0 #define TV_CSC_Y2 0x68014 # define TV_BY_MASK 0x07ff0000 # define TV_BY_SHIFT 16 /** * Y attenuation for component video. * * Stored in 1.9 fixed point. */ # define TV_AY_MASK 0x000003ff # define TV_AY_SHIFT 0 #define TV_CSC_U 0x68018 # define TV_RU_MASK 0x07ff0000 # define TV_RU_SHIFT 16 # define TV_GU_MASK 0x000007ff # define TV_GU_SHIFT 0 #define TV_CSC_U2 0x6801c # define TV_BU_MASK 0x07ff0000 # define TV_BU_SHIFT 16 /** * U attenuation for component video. * * Stored in 1.9 fixed point. */ # define TV_AU_MASK 0x000003ff # define TV_AU_SHIFT 0 #define TV_CSC_V 0x68020 # define TV_RV_MASK 0x0fff0000 # define TV_RV_SHIFT 16 # define TV_GV_MASK 0x000007ff # define TV_GV_SHIFT 0 #define TV_CSC_V2 0x68024 # define TV_BV_MASK 0x07ff0000 # define TV_BV_SHIFT 16 /** * V attenuation for component video. * * Stored in 1.9 fixed point. */ # define TV_AV_MASK 0x000007ff # define TV_AV_SHIFT 0 #define TV_CLR_KNOBS 0x68028 /** 2s-complement brightness adjustment */ # define TV_BRIGHTNESS_MASK 0xff000000 # define TV_BRIGHTNESS_SHIFT 24 /** Contrast adjustment, as a 2.6 unsigned floating point number */ # define TV_CONTRAST_MASK 0x00ff0000 # define TV_CONTRAST_SHIFT 16 /** Saturation adjustment, as a 2.6 unsigned floating point number */ # define TV_SATURATION_MASK 0x0000ff00 # define TV_SATURATION_SHIFT 8 /** Hue adjustment, as an integer phase angle in degrees */ # define TV_HUE_MASK 0x000000ff # define TV_HUE_SHIFT 0 #define TV_CLR_LEVEL 0x6802c /** Controls the DAC level for black */ # define TV_BLACK_LEVEL_MASK 0x01ff0000 # define TV_BLACK_LEVEL_SHIFT 16 /** Controls the DAC level for blanking */ # define TV_BLANK_LEVEL_MASK 0x000001ff # define TV_BLANK_LEVEL_SHIFT 0 #define TV_H_CTL_1 0x68030 /** Number of pixels in the hsync. */ # define TV_HSYNC_END_MASK 0x1fff0000 # define TV_HSYNC_END_SHIFT 16 /** Total number of pixels minus one in the line (display and blanking). */ # define TV_HTOTAL_MASK 0x00001fff # define TV_HTOTAL_SHIFT 0 #define TV_H_CTL_2 0x68034 /** Enables the colorburst (needed for non-component color) */ # define TV_BURST_ENA (1 << 31) /** Offset of the colorburst from the start of hsync, in pixels minus one. */ # define TV_HBURST_START_SHIFT 16 # define TV_HBURST_START_MASK 0x1fff0000 /** Length of the colorburst */ # define TV_HBURST_LEN_SHIFT 0 # define TV_HBURST_LEN_MASK 0x0001fff #define TV_H_CTL_3 0x68038 /** End of hblank, measured in pixels minus one from start of hsync */ # define TV_HBLANK_END_SHIFT 16 # define TV_HBLANK_END_MASK 0x1fff0000 /** Start of hblank, measured in pixels minus one from start of hsync */ # define TV_HBLANK_START_SHIFT 0 # define TV_HBLANK_START_MASK 0x0001fff #define TV_V_CTL_1 0x6803c /** XXX */ # define TV_NBR_END_SHIFT 16 # define TV_NBR_END_MASK 0x07ff0000 /** XXX */ # define TV_VI_END_F1_SHIFT 8 # define TV_VI_END_F1_MASK 0x00003f00 /** XXX */ # define TV_VI_END_F2_SHIFT 0 # define TV_VI_END_F2_MASK 0x0000003f #define TV_V_CTL_2 0x68040 /** Length of vsync, in half lines */ # define TV_VSYNC_LEN_MASK 0x07ff0000 # define TV_VSYNC_LEN_SHIFT 16 /** Offset of the start of vsync in field 1, measured in one less than the * number of half lines. */ # define TV_VSYNC_START_F1_MASK 0x00007f00 # define TV_VSYNC_START_F1_SHIFT 8 /** * Offset of the start of vsync in field 2, measured in one less than the * number of half lines. */ # define TV_VSYNC_START_F2_MASK 0x0000007f # define TV_VSYNC_START_F2_SHIFT 0 #define TV_V_CTL_3 0x68044 /** Enables generation of the equalization signal */ # define TV_EQUAL_ENA (1 << 31) /** Length of vsync, in half lines */ # define TV_VEQ_LEN_MASK 0x007f0000 # define TV_VEQ_LEN_SHIFT 16 /** Offset of the start of equalization in field 1, measured in one less than * the number of half lines. */ # define TV_VEQ_START_F1_MASK 0x0007f00 # define TV_VEQ_START_F1_SHIFT 8 /** * Offset of the start of equalization in field 2, measured in one less than * the number of half lines. */ # define TV_VEQ_START_F2_MASK 0x000007f # define TV_VEQ_START_F2_SHIFT 0 #define TV_V_CTL_4 0x68048 /** * Offset to start of vertical colorburst, measured in one less than the * number of lines from vertical start. */ # define TV_VBURST_START_F1_MASK 0x003f0000 # define TV_VBURST_START_F1_SHIFT 16 /** * Offset to the end of vertical colorburst, measured in one less than the * number of lines from the start of NBR. */ # define TV_VBURST_END_F1_MASK 0x000000ff # define TV_VBURST_END_F1_SHIFT 0 #define TV_V_CTL_5 0x6804c /** * Offset to start of vertical colorburst, measured in one less than the * number of lines from vertical start. */ # define TV_VBURST_START_F2_MASK 0x003f0000 # define TV_VBURST_START_F2_SHIFT 16 /** * Offset to the end of vertical colorburst, measured in one less than the * number of lines from the start of NBR. */ # define TV_VBURST_END_F2_MASK 0x000000ff # define TV_VBURST_END_F2_SHIFT 0 #define TV_V_CTL_6 0x68050 /** * Offset to start of vertical colorburst, measured in one less than the * number of lines from vertical start. */ # define TV_VBURST_START_F3_MASK 0x003f0000 # define TV_VBURST_START_F3_SHIFT 16 /** * Offset to the end of vertical colorburst, measured in one less than the * number of lines from the start of NBR. */ # define TV_VBURST_END_F3_MASK 0x000000ff # define TV_VBURST_END_F3_SHIFT 0 #define TV_V_CTL_7 0x68054 /** * Offset to start of vertical colorburst, measured in one less than the * number of lines from vertical start. */ # define TV_VBURST_START_F4_MASK 0x003f0000 # define TV_VBURST_START_F4_SHIFT 16 /** * Offset to the end of vertical colorburst, measured in one less than the * number of lines from the start of NBR. */ # define TV_VBURST_END_F4_MASK 0x000000ff # define TV_VBURST_END_F4_SHIFT 0 #define TV_SC_CTL_1 0x68060 /** Turns on the first subcarrier phase generation DDA */ # define TV_SC_DDA1_EN (1 << 31) /** Turns on the first subcarrier phase generation DDA */ # define TV_SC_DDA2_EN (1 << 30) /** Turns on the first subcarrier phase generation DDA */ # define TV_SC_DDA3_EN (1 << 29) /** Sets the subcarrier DDA to reset frequency every other field */ # define TV_SC_RESET_EVERY_2 (0 << 24) /** Sets the subcarrier DDA to reset frequency every fourth field */ # define TV_SC_RESET_EVERY_4 (1 << 24) /** Sets the subcarrier DDA to reset frequency every eighth field */ # define TV_SC_RESET_EVERY_8 (2 << 24) /** Sets the subcarrier DDA to never reset the frequency */ # define TV_SC_RESET_NEVER (3 << 24) /** Sets the peak amplitude of the colorburst.*/ # define TV_BURST_LEVEL_MASK 0x00ff0000 # define TV_BURST_LEVEL_SHIFT 16 /** Sets the increment of the first subcarrier phase generation DDA */ # define TV_SCDDA1_INC_MASK 0x00000fff # define TV_SCDDA1_INC_SHIFT 0 #define TV_SC_CTL_2 0x68064 /** Sets the rollover for the second subcarrier phase generation DDA */ # define TV_SCDDA2_SIZE_MASK 0x7fff0000 # define TV_SCDDA2_SIZE_SHIFT 16 /** Sets the increent of the second subcarrier phase generation DDA */ # define TV_SCDDA2_INC_MASK 0x00007fff # define TV_SCDDA2_INC_SHIFT 0 #define TV_SC_CTL_3 0x68068 /** Sets the rollover for the third subcarrier phase generation DDA */ # define TV_SCDDA3_SIZE_MASK 0x7fff0000 # define TV_SCDDA3_SIZE_SHIFT 16 /** Sets the increent of the third subcarrier phase generation DDA */ # define TV_SCDDA3_INC_MASK 0x00007fff # define TV_SCDDA3_INC_SHIFT 0 #define TV_WIN_POS 0x68070 /** X coordinate of the display from the start of horizontal active */ # define TV_XPOS_MASK 0x1fff0000 # define TV_XPOS_SHIFT 16 /** Y coordinate of the display from the start of vertical active (NBR) */ # define TV_YPOS_MASK 0x00000fff # define TV_YPOS_SHIFT 0 #define TV_WIN_SIZE 0x68074 /** Horizontal size of the display window, measured in pixels*/ # define TV_XSIZE_MASK 0x1fff0000 # define TV_XSIZE_SHIFT 16 /** * Vertical size of the display window, measured in pixels. * * Must be even for interlaced modes. */ # define TV_YSIZE_MASK 0x00000fff # define TV_YSIZE_SHIFT 0 #define TV_FILTER_CTL_1 0x68080 /** * Enables automatic scaling calculation. * * If set, the rest of the registers are ignored, and the calculated values can * be read back from the register. */ # define TV_AUTO_SCALE (1 << 31) /** * Disables the vertical filter. * * This is required on modes more than 1024 pixels wide */ # define TV_V_FILTER_BYPASS (1 << 29) /** Enables adaptive vertical filtering */ # define TV_VADAPT (1 << 28) # define TV_VADAPT_MODE_MASK (3 << 26) /** Selects the least adaptive vertical filtering mode */ # define TV_VADAPT_MODE_LEAST (0 << 26) /** Selects the moderately adaptive vertical filtering mode */ # define TV_VADAPT_MODE_MODERATE (1 << 26) /** Selects the most adaptive vertical filtering mode */ # define TV_VADAPT_MODE_MOST (3 << 26) /** * Sets the horizontal scaling factor. * * This should be the fractional part of the horizontal scaling factor divided * by the oversampling rate. TV_HSCALE should be less than 1, and set to: * * (src width - 1) / ((oversample * dest width) - 1) */ # define TV_HSCALE_FRAC_MASK 0x00003fff # define TV_HSCALE_FRAC_SHIFT 0 #define TV_FILTER_CTL_2 0x68084 /** * Sets the integer part of the 3.15 fixed-point vertical scaling factor. * * TV_VSCALE should be (src height - 1) / ((interlace * dest height) - 1) */ # define TV_VSCALE_INT_MASK 0x00038000 # define TV_VSCALE_INT_SHIFT 15 /** * Sets the fractional part of the 3.15 fixed-point vertical scaling factor. * * \sa TV_VSCALE_INT_MASK */ # define TV_VSCALE_FRAC_MASK 0x00007fff # define TV_VSCALE_FRAC_SHIFT 0 #define TV_FILTER_CTL_3 0x68088 /** * Sets the integer part of the 3.15 fixed-point vertical scaling factor. * * TV_VSCALE should be (src height - 1) / (1/4 * (dest height - 1)) * * For progressive modes, TV_VSCALE_IP_INT should be set to zeroes. */ # define TV_VSCALE_IP_INT_MASK 0x00038000 # define TV_VSCALE_IP_INT_SHIFT 15 /** * Sets the fractional part of the 3.15 fixed-point vertical scaling factor. * * For progressive modes, TV_VSCALE_IP_INT should be set to zeroes. * * \sa TV_VSCALE_IP_INT_MASK */ # define TV_VSCALE_IP_FRAC_MASK 0x00007fff # define TV_VSCALE_IP_FRAC_SHIFT 0 #define TV_CC_CONTROL 0x68090 # define TV_CC_ENABLE (1 << 31) /** * Specifies which field to send the CC data in. * * CC data is usually sent in field 0. */ # define TV_CC_FID_MASK (1 << 27) # define TV_CC_FID_SHIFT 27 /** Sets the horizontal position of the CC data. Usually 135. */ # define TV_CC_HOFF_MASK 0x03ff0000 # define TV_CC_HOFF_SHIFT 16 /** Sets the vertical position of the CC data. Usually 21 */ # define TV_CC_LINE_MASK 0x0000003f # define TV_CC_LINE_SHIFT 0 #define TV_CC_DATA 0x68094 # define TV_CC_RDY (1 << 31) /** Second word of CC data to be transmitted. */ # define TV_CC_DATA_2_MASK 0x007f0000 # define TV_CC_DATA_2_SHIFT 16 /** First word of CC data to be transmitted. */ # define TV_CC_DATA_1_MASK 0x0000007f # define TV_CC_DATA_1_SHIFT 0 #define TV_H_LUMA_0 0x68100 #define TV_H_LUMA_59 0x681ec #define TV_H_CHROMA_0 0x68200 #define TV_H_CHROMA_59 0x682ec #define TV_V_LUMA_0 0x68300 #define TV_V_LUMA_42 0x683a8 #define TV_V_CHROMA_0 0x68400 #define TV_V_CHROMA_42 0x684a8 /* Display Port */ #define DP_A 0x64000 /* eDP */ #define DP_B 0x64100 #define DP_C 0x64200 #define DP_D 0x64300 #define DP_PORT_EN (1 << 31) #define DP_PIPEB_SELECT (1 << 30) /* Link training mode - select a suitable mode for each stage */ #define DP_LINK_TRAIN_PAT_1 (0 << 28) #define DP_LINK_TRAIN_PAT_2 (1 << 28) #define DP_LINK_TRAIN_PAT_IDLE (2 << 28) #define DP_LINK_TRAIN_OFF (3 << 28) #define DP_LINK_TRAIN_MASK (3 << 28) #define DP_LINK_TRAIN_SHIFT 28 /* Signal voltages. These are mostly controlled by the other end */ #define DP_VOLTAGE_0_4 (0 << 25) #define DP_VOLTAGE_0_6 (1 << 25) #define DP_VOLTAGE_0_8 (2 << 25) #define DP_VOLTAGE_1_2 (3 << 25) #define DP_VOLTAGE_MASK (7 << 25) #define DP_VOLTAGE_SHIFT 25 /* Signal pre-emphasis levels, like voltages, the other end tells us what * they want */ #define DP_PRE_EMPHASIS_0 (0 << 22) #define DP_PRE_EMPHASIS_3_5 (1 << 22) #define DP_PRE_EMPHASIS_6 (2 << 22) #define DP_PRE_EMPHASIS_9_5 (3 << 22) #define DP_PRE_EMPHASIS_MASK (7 << 22) #define DP_PRE_EMPHASIS_SHIFT 22 /* How many wires to use. I guess 3 was too hard */ #define DP_PORT_WIDTH_1 (0 << 19) #define DP_PORT_WIDTH_2 (1 << 19) #define DP_PORT_WIDTH_4 (3 << 19) #define DP_PORT_WIDTH_MASK (7 << 19) /* Mystic DPCD version 1.1 special mode */ #define DP_ENHANCED_FRAMING (1 << 18) /* eDP */ #define DP_PLL_FREQ_270MHZ (0 << 16) #define DP_PLL_FREQ_160MHZ (1 << 16) #define DP_PLL_FREQ_MASK (3 << 16) /** locked once port is enabled */ #define DP_PORT_REVERSAL (1 << 15) /* eDP */ #define DP_PLL_ENABLE (1 << 14) /** sends the clock on lane 15 of the PEG for debug */ #define DP_CLOCK_OUTPUT_ENABLE (1 << 13) #define DP_SCRAMBLING_DISABLE (1 << 12) #define DP_SCRAMBLING_DISABLE_IGDNG (1 << 7) /** limit RGB values to avoid confusing TVs */ #define DP_COLOR_RANGE_16_235 (1 << 8) /** Turn on the audio link */ #define DP_AUDIO_OUTPUT_ENABLE (1 << 6) /** vs and hs sync polarity */ #define DP_SYNC_VS_HIGH (1 << 4) #define DP_SYNC_HS_HIGH (1 << 3) /** A fantasy */ #define DP_DETECTED (1 << 2) /** The aux channel provides a way to talk to the * signal sink for DDC etc. Max packet size supported * is 20 bytes in each direction, hence the 5 fixed * data registers */ #define DPA_AUX_CH_CTL 0x64010 #define DPA_AUX_CH_DATA1 0x64014 #define DPA_AUX_CH_DATA2 0x64018 #define DPA_AUX_CH_DATA3 0x6401c #define DPA_AUX_CH_DATA4 0x64020 #define DPA_AUX_CH_DATA5 0x64024 #define DPB_AUX_CH_CTL 0x64110 #define DPB_AUX_CH_DATA1 0x64114 #define DPB_AUX_CH_DATA2 0x64118 #define DPB_AUX_CH_DATA3 0x6411c #define DPB_AUX_CH_DATA4 0x64120 #define DPB_AUX_CH_DATA5 0x64124 #define DPC_AUX_CH_CTL 0x64210 #define DPC_AUX_CH_DATA1 0x64214 #define DPC_AUX_CH_DATA2 0x64218 #define DPC_AUX_CH_DATA3 0x6421c #define DPC_AUX_CH_DATA4 0x64220 #define DPC_AUX_CH_DATA5 0x64224 #define DPD_AUX_CH_CTL 0x64310 #define DPD_AUX_CH_DATA1 0x64314 #define DPD_AUX_CH_DATA2 0x64318 #define DPD_AUX_CH_DATA3 0x6431c #define DPD_AUX_CH_DATA4 0x64320 #define DPD_AUX_CH_DATA5 0x64324 #define DP_AUX_CH_CTL_SEND_BUSY (1 << 31) #define DP_AUX_CH_CTL_DONE (1 << 30) #define DP_AUX_CH_CTL_INTERRUPT (1 << 29) #define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28) #define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26) #define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26) #define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26) #define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26) #define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26) #define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25) #define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20) #define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20 #define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16) #define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16 #define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15) #define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14) #define DP_AUX_CH_CTL_SYNC_TEST (1 << 13) #define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12) #define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11) #define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff) #define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0 /* * Computing GMCH M and N values for the Display Port link * * GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes * * ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz) * * The GMCH value is used internally * * bytes_per_pixel is the number of bytes coming out of the plane, * which is after the LUTs, so we want the bytes for our color format. * For our current usage, this is always 3, one byte for R, G and B. */ #define PIPEA_GMCH_DATA_M 0x70050 #define PIPEB_GMCH_DATA_M 0x71050 /* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */ #define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25) #define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25 #define PIPE_GMCH_DATA_M_MASK (0xffffff) #define PIPEA_GMCH_DATA_N 0x70054 #define PIPEB_GMCH_DATA_N 0x71054 #define PIPE_GMCH_DATA_N_MASK (0xffffff) /* * Computing Link M and N values for the Display Port link * * Link M / N = pixel_clock / ls_clk * * (the DP spec calls pixel_clock the 'strm_clk') * * The Link value is transmitted in the Main Stream * Attributes and VB-ID. */ #define PIPEA_DP_LINK_M 0x70060 #define PIPEB_DP_LINK_M 0x71060 #define PIPEA_DP_LINK_M_MASK (0xffffff) #define PIPEA_DP_LINK_N 0x70064 #define PIPEB_DP_LINK_N 0x71064 #define PIPEA_DP_LINK_N_MASK (0xffffff) /* Display & cursor control */ /* Pipe A */ #define PIPEADSL 0x70000 #define PIPEACONF 0x70008 #define PIPEACONF_ENABLE (1<<31) #define PIPEACONF_DISABLE 0 #define PIPEACONF_DOUBLE_WIDE (1<<30) #define I965_PIPECONF_ACTIVE (1<<30) #define PIPEACONF_SINGLE_WIDE 0 #define PIPEACONF_PIPE_UNLOCKED 0 #define PIPEACONF_PIPE_LOCKED (1<<25) #define PIPEACONF_PALETTE 0 #define PIPEACONF_GAMMA (1<<24) #define PIPECONF_FORCE_BORDER (1<<25) #define PIPECONF_PROGRESSIVE (0 << 21) #define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21) #define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21) #define PIPECONF_CXSR_DOWNCLOCK (1<<16) #define PIPEASTAT 0x70024 #define PIPE_FIFO_UNDERRUN_STATUS (1UL<<31) #define PIPE_CRC_ERROR_ENABLE (1UL<<29) #define PIPE_CRC_DONE_ENABLE (1UL<<28) #define PIPE_GMBUS_EVENT_ENABLE (1UL<<27) #define PIPE_HOTPLUG_INTERRUPT_ENABLE (1UL<<26) #define PIPE_VSYNC_INTERRUPT_ENABLE (1UL<<25) #define PIPE_DISPLAY_LINE_COMPARE_ENABLE (1UL<<24) #define PIPE_DPST_EVENT_ENABLE (1UL<<23) #define PIPE_LEGACY_BLC_EVENT_ENABLE (1UL<<22) #define PIPE_ODD_FIELD_INTERRUPT_ENABLE (1UL<<21) #define PIPE_EVEN_FIELD_INTERRUPT_ENABLE (1UL<<20) #define PIPE_HOTPLUG_TV_INTERRUPT_ENABLE (1UL<<18) /* pre-965 */ #define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL<<18) /* 965 or later */ #define PIPE_VBLANK_INTERRUPT_ENABLE (1UL<<17) #define PIPE_OVERLAY_UPDATED_ENABLE (1UL<<16) #define PIPE_CRC_ERROR_INTERRUPT_STATUS (1UL<<13) #define PIPE_CRC_DONE_INTERRUPT_STATUS (1UL<<12) #define PIPE_GMBUS_INTERRUPT_STATUS (1UL<<11) #define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL<<10) #define PIPE_VSYNC_INTERRUPT_STATUS (1UL<<9) #define PIPE_DISPLAY_LINE_COMPARE_STATUS (1UL<<8) #define PIPE_DPST_EVENT_STATUS (1UL<<7) #define PIPE_LEGACY_BLC_EVENT_STATUS (1UL<<6) #define PIPE_ODD_FIELD_INTERRUPT_STATUS (1UL<<5) #define PIPE_EVEN_FIELD_INTERRUPT_STATUS (1UL<<4) #define PIPE_HOTPLUG_TV_INTERRUPT_STATUS (1UL<<2) /* pre-965 */ #define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */ #define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1) #define PIPE_OVERLAY_UPDATED_STATUS (1UL<<0) #define PIPE_BPC_MASK (7 << 5) /* Ironlake */ #define PIPE_8BPC (0 << 5) #define PIPE_10BPC (1 << 5) #define PIPE_6BPC (2 << 5) #define PIPE_12BPC (3 << 5) #define DSPARB 0x70030 #define DSPARB_CSTART_MASK (0x7f << 7) #define DSPARB_CSTART_SHIFT 7 #define DSPARB_BSTART_MASK (0x7f) #define DSPARB_BSTART_SHIFT 0 #define DSPARB_BEND_SHIFT 9 /* on 855 */ #define DSPARB_AEND_SHIFT 0 #define DSPFW1 0x70034 #define DSPFW2 0x70038 #define DSPFW3 0x7003c #define IGD_SELF_REFRESH_EN (1<<30) /* FIFO watermark sizes etc */ #define I915_FIFO_LINE_SIZE 64 #define I830_FIFO_LINE_SIZE 32 #define I945_FIFO_SIZE 127 /* 945 & 965 */ #define I915_FIFO_SIZE 95 #define I855GM_FIFO_SIZE 127 /* In cachelines */ #define I830_FIFO_SIZE 95 #define I915_MAX_WM 0x3f #define IGD_DISPLAY_FIFO 512 /* in 64byte unit */ #define IGD_FIFO_LINE_SIZE 64 #define IGD_MAX_WM 0x1ff #define IGD_DFT_WM 0x3f #define IGD_DFT_HPLLOFF_WM 0 #define IGD_GUARD_WM 10 #define IGD_CURSOR_FIFO 64 #define IGD_CURSOR_MAX_WM 0x3f #define IGD_CURSOR_DFT_WM 0 #define IGD_CURSOR_GUARD_WM 5 /* * The two pipe frame counter registers are not synchronized, so * reading a stable value is somewhat tricky. The following code * should work: * * do { * high1 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >> * PIPE_FRAME_HIGH_SHIFT; * low1 = ((INREG(PIPEAFRAMEPIXEL) & PIPE_FRAME_LOW_MASK) >> * PIPE_FRAME_LOW_SHIFT); * high2 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >> * PIPE_FRAME_HIGH_SHIFT); * } while (high1 != high2); * frame = (high1 << 8) | low1; */ #define PIPEAFRAMEHIGH 0x70040 #define PIPE_FRAME_HIGH_MASK 0x0000ffff #define PIPE_FRAME_HIGH_SHIFT 0 #define PIPEAFRAMEPIXEL 0x70044 #define PIPE_FRAME_LOW_MASK 0xff000000 #define PIPE_FRAME_LOW_SHIFT 24 #define PIPE_PIXEL_MASK 0x00ffffff #define PIPE_PIXEL_SHIFT 0 /* GM45+ just has to be different */ #define PIPEA_FRMCOUNT_GM45 0x70040 #define PIPEA_FLIPCOUNT_GM45 0x70044 /* Cursor A & B regs */ #define CURACNTR 0x70080 /* Old style CUR*CNTR flags (desktop 8xx) */ #define CURSOR_ENABLE 0x80000000 #define CURSOR_GAMMA_ENABLE 0x40000000 #define CURSOR_STRIDE_MASK 0x30000000 #define CURSOR_FORMAT_SHIFT 24 #define CURSOR_FORMAT_MASK (0x07 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_2C (0x00 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_3C (0x01 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_4C (0x02 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_ARGB (0x04 << CURSOR_FORMAT_SHIFT) #define CURSOR_FORMAT_XRGB (0x05 << CURSOR_FORMAT_SHIFT) /* New style CUR*CNTR flags */ #define CURSOR_MODE 0x27 #define CURSOR_MODE_DISABLE 0x00 #define CURSOR_MODE_64_32B_AX 0x07 #define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX) #define MCURSOR_PIPE_SELECT (1 << 28) #define MCURSOR_PIPE_A 0x00 #define MCURSOR_PIPE_B (1 << 28) #define MCURSOR_GAMMA_ENABLE (1 << 26) #define CURABASE 0x70084 #define CURAPOS 0x70088 #define CURSOR_POS_MASK 0x007FF #define CURSOR_POS_SIGN 0x8000 #define CURSOR_X_SHIFT 0 #define CURSOR_Y_SHIFT 16 #define CURSIZE 0x700a0 #define CURBCNTR 0x700c0 #define CURBBASE 0x700c4 #define CURBPOS 0x700c8 /* Display A control */ #define DSPACNTR 0x70180 #define DISPLAY_PLANE_ENABLE (1<<31) #define DISPLAY_PLANE_DISABLE 0 #define DISPPLANE_GAMMA_ENABLE (1<<30) #define DISPPLANE_GAMMA_DISABLE 0 #define DISPPLANE_PIXFORMAT_MASK (0xf<<26) #define DISPPLANE_8BPP (0x2<<26) #define DISPPLANE_15_16BPP (0x4<<26) #define DISPPLANE_16BPP (0x5<<26) #define DISPPLANE_32BPP_NO_ALPHA (0x6<<26) #define DISPPLANE_32BPP (0x7<<26) #define DISPPLANE_STEREO_ENABLE (1<<25) #define DISPPLANE_STEREO_DISABLE 0 #define DISPPLANE_SEL_PIPE_MASK (1<<24) #define DISPPLANE_SEL_PIPE_A 0 #define DISPPLANE_SEL_PIPE_B (1<<24) #define DISPPLANE_SRC_KEY_ENABLE (1<<22) #define DISPPLANE_SRC_KEY_DISABLE 0 #define DISPPLANE_LINE_DOUBLE (1<<20) #define DISPPLANE_NO_LINE_DOUBLE 0 #define DISPPLANE_STEREO_POLARITY_FIRST 0 #define DISPPLANE_STEREO_POLARITY_SECOND (1<<18) #define DISPPLANE_TRICKLE_FEED_DISABLE (1<<14) /* IGDNG */ #define DISPPLANE_TILED (1<<10) #define DSPAADDR 0x70184 #define DSPASTRIDE 0x70188 #define DSPAPOS 0x7018C /* reserved */ #define DSPASIZE 0x70190 #define DSPASURF 0x7019C /* 965+ only */ #define DSPATILEOFF 0x701A4 /* 965+ only */ /* VBIOS flags */ #define SWF00 0x71410 #define SWF01 0x71414 #define SWF02 0x71418 #define SWF03 0x7141c #define SWF04 0x71420 #define SWF05 0x71424 #define SWF06 0x71428 #define SWF10 0x70410 #define SWF11 0x70414 #define SWF14 0x71420 #define SWF30 0x72414 #define SWF31 0x72418 #define SWF32 0x7241c /* Pipe B */ #define PIPEBDSL 0x71000 #define PIPEBCONF 0x71008 #define PIPEBSTAT 0x71024 #define PIPEBFRAMEHIGH 0x71040 #define PIPEBFRAMEPIXEL 0x71044 #define PIPEB_FRMCOUNT_GM45 0x71040 #define PIPEB_FLIPCOUNT_GM45 0x71044 /* Display B control */ #define DSPBCNTR 0x71180 #define DISPPLANE_ALPHA_TRANS_ENABLE (1<<15) #define DISPPLANE_ALPHA_TRANS_DISABLE 0 #define DISPPLANE_SPRITE_ABOVE_DISPLAY 0 #define DISPPLANE_SPRITE_ABOVE_OVERLAY (1) #define DSPBADDR 0x71184 #define DSPBSTRIDE 0x71188 #define DSPBPOS 0x7118C #define DSPBSIZE 0x71190 #define DSPBSURF 0x7119C #define DSPBTILEOFF 0x711A4 /* VBIOS regs */ #define VGACNTRL 0x71400 # define VGA_DISP_DISABLE (1 << 31) # define VGA_2X_MODE (1 << 30) # define VGA_PIPE_B_SELECT (1 << 29) /* IGDNG */ #define CPU_VGACNTRL 0x41000 #define DIGITAL_PORT_HOTPLUG_CNTRL 0x44030 #define DIGITAL_PORTA_HOTPLUG_ENABLE (1 << 4) #define DIGITAL_PORTA_SHORT_PULSE_2MS (0 << 2) #define DIGITAL_PORTA_SHORT_PULSE_4_5MS (1 << 2) #define DIGITAL_PORTA_SHORT_PULSE_6MS (2 << 2) #define DIGITAL_PORTA_SHORT_PULSE_100MS (3 << 2) #define DIGITAL_PORTA_NO_DETECT (0 << 0) #define DIGITAL_PORTA_LONG_PULSE_DETECT_MASK (1 << 1) #define DIGITAL_PORTA_SHORT_PULSE_DETECT_MASK (1 << 0) /* refresh rate hardware control */ #define RR_HW_CTL 0x45300 #define RR_HW_LOW_POWER_FRAMES_MASK 0xff #define RR_HW_HIGH_POWER_FRAMES_MASK 0xff00 #define FDI_PLL_BIOS_0 0x46000 #define FDI_PLL_BIOS_1 0x46004 #define FDI_PLL_BIOS_2 0x46008 #define DISPLAY_PORT_PLL_BIOS_0 0x4600c #define DISPLAY_PORT_PLL_BIOS_1 0x46010 #define DISPLAY_PORT_PLL_BIOS_2 0x46014 #define FDI_PLL_FREQ_CTL 0x46030 #define FDI_PLL_FREQ_CHANGE_REQUEST (1<<24) #define FDI_PLL_FREQ_LOCK_LIMIT_MASK 0xfff00 #define FDI_PLL_FREQ_DISABLE_COUNT_LIMIT_MASK 0xff #define PIPEA_DATA_M1 0x60030 #define TU_SIZE(x) (((x)-1) << 25) /* default size 64 */ #define TU_SIZE_MASK 0x7e000000 #define PIPEA_DATA_M1_OFFSET 0 #define PIPEA_DATA_N1 0x60034 #define PIPEA_DATA_N1_OFFSET 0 #define PIPEA_DATA_M2 0x60038 #define PIPEA_DATA_M2_OFFSET 0 #define PIPEA_DATA_N2 0x6003c #define PIPEA_DATA_N2_OFFSET 0 #define PIPEA_LINK_M1 0x60040 #define PIPEA_LINK_M1_OFFSET 0 #define PIPEA_LINK_N1 0x60044 #define PIPEA_LINK_N1_OFFSET 0 #define PIPEA_LINK_M2 0x60048 #define PIPEA_LINK_M2_OFFSET 0 #define PIPEA_LINK_N2 0x6004c #define PIPEA_LINK_N2_OFFSET 0 /* PIPEB timing regs are same start from 0x61000 */ #define PIPEB_DATA_M1 0x61030 #define PIPEB_DATA_M1_OFFSET 0 #define PIPEB_DATA_N1 0x61034 #define PIPEB_DATA_N1_OFFSET 0 #define PIPEB_DATA_M2 0x61038 #define PIPEB_DATA_M2_OFFSET 0 #define PIPEB_DATA_N2 0x6103c #define PIPEB_DATA_N2_OFFSET 0 #define PIPEB_LINK_M1 0x61040 #define PIPEB_LINK_M1_OFFSET 0 #define PIPEB_LINK_N1 0x61044 #define PIPEB_LINK_N1_OFFSET 0 #define PIPEB_LINK_M2 0x61048 #define PIPEB_LINK_M2_OFFSET 0 #define PIPEB_LINK_N2 0x6104c #define PIPEB_LINK_N2_OFFSET 0 /* CPU panel fitter */ #define PFA_CTL_1 0x68080 #define PFB_CTL_1 0x68880 #define PF_ENABLE (1<<31) #define PF_FILTER_MASK (3<<23) #define PF_FILTER_PROGRAMMED (0<<23) #define PF_FILTER_MED_3x3 (1<<23) #define PF_FILTER_EDGE_ENHANCE (2<<23) #define PF_FILTER_EDGE_SOFTEN (3<<23) #define PFA_WIN_SZ 0x68074 #define PFB_WIN_SZ 0x68874 #define PFA_WIN_POS 0x68070 #define PFB_WIN_POS 0x68870 /* legacy palette */ #define LGC_PALETTE_A 0x4a000 #define LGC_PALETTE_B 0x4a800 /* interrupts */ #define DE_MASTER_IRQ_CONTROL (1 << 31) #define DE_SPRITEB_FLIP_DONE (1 << 29) #define DE_SPRITEA_FLIP_DONE (1 << 28) #define DE_PLANEB_FLIP_DONE (1 << 27) #define DE_PLANEA_FLIP_DONE (1 << 26) #define DE_PCU_EVENT (1 << 25) #define DE_GTT_FAULT (1 << 24) #define DE_POISON (1 << 23) #define DE_PERFORM_COUNTER (1 << 22) #define DE_PCH_EVENT (1 << 21) #define DE_AUX_CHANNEL_A (1 << 20) #define DE_DP_A_HOTPLUG (1 << 19) #define DE_GSE (1 << 18) #define DE_PIPEB_VBLANK (1 << 15) #define DE_PIPEB_EVEN_FIELD (1 << 14) #define DE_PIPEB_ODD_FIELD (1 << 13) #define DE_PIPEB_LINE_COMPARE (1 << 12) #define DE_PIPEB_VSYNC (1 << 11) #define DE_PIPEB_FIFO_UNDERRUN (1 << 8) #define DE_PIPEA_VBLANK (1 << 7) #define DE_PIPEA_EVEN_FIELD (1 << 6) #define DE_PIPEA_ODD_FIELD (1 << 5) #define DE_PIPEA_LINE_COMPARE (1 << 4) #define DE_PIPEA_VSYNC (1 << 3) #define DE_PIPEA_FIFO_UNDERRUN (1 << 0) #define DEISR 0x44000 #define DEIMR 0x44004 #define DEIIR 0x44008 #define DEIER 0x4400c /* GT interrupt */ #define GT_SYNC_STATUS (1 << 2) #define GT_USER_INTERRUPT (1 << 0) #define GTISR 0x44010 #define GTIMR 0x44014 #define GTIIR 0x44018 #define GTIER 0x4401c #define DISP_ARB_CTL 0x45000 #define DISP_TILE_SURFACE_SWIZZLING (1<<13) /* PCH */ /* south display engine interrupt */ #define SDE_CRT_HOTPLUG (1 << 11) #define SDE_PORTD_HOTPLUG (1 << 10) #define SDE_PORTC_HOTPLUG (1 << 9) #define SDE_PORTB_HOTPLUG (1 << 8) #define SDE_SDVOB_HOTPLUG (1 << 6) #define SDEISR 0xc4000 #define SDEIMR 0xc4004 #define SDEIIR 0xc4008 #define SDEIER 0xc400c /* digital port hotplug */ #define PCH_PORT_HOTPLUG 0xc4030 #define PORTD_HOTPLUG_ENABLE (1 << 20) #define PORTD_PULSE_DURATION_2ms (0) #define PORTD_PULSE_DURATION_4_5ms (1 << 18) #define PORTD_PULSE_DURATION_6ms (2 << 18) #define PORTD_PULSE_DURATION_100ms (3 << 18) #define PORTD_HOTPLUG_NO_DETECT (0) #define PORTD_HOTPLUG_SHORT_DETECT (1 << 16) #define PORTD_HOTPLUG_LONG_DETECT (1 << 17) #define PORTC_HOTPLUG_ENABLE (1 << 12) #define PORTC_PULSE_DURATION_2ms (0) #define PORTC_PULSE_DURATION_4_5ms (1 << 10) #define PORTC_PULSE_DURATION_6ms (2 << 10) #define PORTC_PULSE_DURATION_100ms (3 << 10) #define PORTC_HOTPLUG_NO_DETECT (0) #define PORTC_HOTPLUG_SHORT_DETECT (1 << 8) #define PORTC_HOTPLUG_LONG_DETECT (1 << 9) #define PORTB_HOTPLUG_ENABLE (1 << 4) #define PORTB_PULSE_DURATION_2ms (0) #define PORTB_PULSE_DURATION_4_5ms (1 << 2) #define PORTB_PULSE_DURATION_6ms (2 << 2) #define PORTB_PULSE_DURATION_100ms (3 << 2) #define PORTB_HOTPLUG_NO_DETECT (0) #define PORTB_HOTPLUG_SHORT_DETECT (1 << 0) #define PORTB_HOTPLUG_LONG_DETECT (1 << 1) #define PCH_GPIOA 0xc5010 #define PCH_GPIOB 0xc5014 #define PCH_GPIOC 0xc5018 #define PCH_GPIOD 0xc501c #define PCH_GPIOE 0xc5020 #define PCH_GPIOF 0xc5024 #define PCH_DPLL_A 0xc6014 #define PCH_DPLL_B 0xc6018 #define PCH_FPA0 0xc6040 #define PCH_FPA1 0xc6044 #define PCH_FPB0 0xc6048 #define PCH_FPB1 0xc604c #define PCH_DPLL_TEST 0xc606c #define PCH_DREF_CONTROL 0xC6200 #define DREF_CONTROL_MASK 0x7fc3 #define DREF_CPU_SOURCE_OUTPUT_DISABLE (0<<13) #define DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD (2<<13) #define DREF_CPU_SOURCE_OUTPUT_NONSPREAD (3<<13) #define DREF_CPU_SOURCE_OUTPUT_MASK (3<<13) #define DREF_SSC_SOURCE_DISABLE (0<<11) #define DREF_SSC_SOURCE_ENABLE (2<<11) #define DREF_SSC_SOURCE_MASK (3<<11) #define DREF_NONSPREAD_SOURCE_DISABLE (0<<9) #define DREF_NONSPREAD_CK505_ENABLE (1<<9) #define DREF_NONSPREAD_SOURCE_ENABLE (2<<9) #define DREF_NONSPREAD_SOURCE_MASK (3<<9) #define DREF_SUPERSPREAD_SOURCE_DISABLE (0<<7) #define DREF_SUPERSPREAD_SOURCE_ENABLE (2<<7) #define DREF_SSC4_DOWNSPREAD (0<<6) #define DREF_SSC4_CENTERSPREAD (1<<6) #define DREF_SSC1_DISABLE (0<<1) #define DREF_SSC1_ENABLE (1<<1) #define DREF_SSC4_DISABLE (0) #define DREF_SSC4_ENABLE (1) #define PCH_RAWCLK_FREQ 0xc6204 #define FDL_TP1_TIMER_SHIFT 12 #define FDL_TP1_TIMER_MASK (3<<12) #define FDL_TP2_TIMER_SHIFT 10 #define FDL_TP2_TIMER_MASK (3<<10) #define RAWCLK_FREQ_MASK 0x3ff #define PCH_DPLL_TMR_CFG 0xc6208 #define PCH_SSC4_PARMS 0xc6210 #define PCH_SSC4_AUX_PARMS 0xc6214 /* transcoder */ #define TRANS_HTOTAL_A 0xe0000 #define TRANS_HTOTAL_SHIFT 16 #define TRANS_HACTIVE_SHIFT 0 #define TRANS_HBLANK_A 0xe0004 #define TRANS_HBLANK_END_SHIFT 16 #define TRANS_HBLANK_START_SHIFT 0 #define TRANS_HSYNC_A 0xe0008 #define TRANS_HSYNC_END_SHIFT 16 #define TRANS_HSYNC_START_SHIFT 0 #define TRANS_VTOTAL_A 0xe000c #define TRANS_VTOTAL_SHIFT 16 #define TRANS_VACTIVE_SHIFT 0 #define TRANS_VBLANK_A 0xe0010 #define TRANS_VBLANK_END_SHIFT 16 #define TRANS_VBLANK_START_SHIFT 0 #define TRANS_VSYNC_A 0xe0014 #define TRANS_VSYNC_END_SHIFT 16 #define TRANS_VSYNC_START_SHIFT 0 #define TRANSA_DATA_M1 0xe0030 #define TRANSA_DATA_N1 0xe0034 #define TRANSA_DATA_M2 0xe0038 #define TRANSA_DATA_N2 0xe003c #define TRANSA_DP_LINK_M1 0xe0040 #define TRANSA_DP_LINK_N1 0xe0044 #define TRANSA_DP_LINK_M2 0xe0048 #define TRANSA_DP_LINK_N2 0xe004c #define TRANS_HTOTAL_B 0xe1000 #define TRANS_HBLANK_B 0xe1004 #define TRANS_HSYNC_B 0xe1008 #define TRANS_VTOTAL_B 0xe100c #define TRANS_VBLANK_B 0xe1010 #define TRANS_VSYNC_B 0xe1014 #define TRANSB_DATA_M1 0xe1030 #define TRANSB_DATA_N1 0xe1034 #define TRANSB_DATA_M2 0xe1038 #define TRANSB_DATA_N2 0xe103c #define TRANSB_DP_LINK_M1 0xe1040 #define TRANSB_DP_LINK_N1 0xe1044 #define TRANSB_DP_LINK_M2 0xe1048 #define TRANSB_DP_LINK_N2 0xe104c #define TRANSACONF 0xf0008 #define TRANSBCONF 0xf1008 #define TRANS_DISABLE (0<<31) #define TRANS_ENABLE (1<<31) #define TRANS_STATE_MASK (1<<30) #define TRANS_STATE_DISABLE (0<<30) #define TRANS_STATE_ENABLE (1<<30) #define TRANS_FSYNC_DELAY_HB1 (0<<27) #define TRANS_FSYNC_DELAY_HB2 (1<<27) #define TRANS_FSYNC_DELAY_HB3 (2<<27) #define TRANS_FSYNC_DELAY_HB4 (3<<27) #define TRANS_DP_AUDIO_ONLY (1<<26) #define TRANS_DP_VIDEO_AUDIO (0<<26) #define TRANS_PROGRESSIVE (0<<21) #define TRANS_8BPC (0<<5) #define TRANS_10BPC (1<<5) #define TRANS_6BPC (2<<5) #define TRANS_12BPC (3<<5) #define FDI_RXA_CHICKEN 0xc200c #define FDI_RXB_CHICKEN 0xc2010 #define FDI_RX_PHASE_SYNC_POINTER_ENABLE (1) /* CPU: FDI_TX */ #define FDI_TXA_CTL 0x60100 #define FDI_TXB_CTL 0x61100 #define FDI_TX_DISABLE (0<<31) #define FDI_TX_ENABLE (1<<31) #define FDI_LINK_TRAIN_PATTERN_1 (0<<28) #define FDI_LINK_TRAIN_PATTERN_2 (1<<28) #define FDI_LINK_TRAIN_PATTERN_IDLE (2<<28) #define FDI_LINK_TRAIN_NONE (3<<28) #define FDI_LINK_TRAIN_VOLTAGE_0_4V (0<<25) #define FDI_LINK_TRAIN_VOLTAGE_0_6V (1<<25) #define FDI_LINK_TRAIN_VOLTAGE_0_8V (2<<25) #define FDI_LINK_TRAIN_VOLTAGE_1_2V (3<<25) #define FDI_LINK_TRAIN_PRE_EMPHASIS_NONE (0<<22) #define FDI_LINK_TRAIN_PRE_EMPHASIS_1_5X (1<<22) #define FDI_LINK_TRAIN_PRE_EMPHASIS_2X (2<<22) #define FDI_LINK_TRAIN_PRE_EMPHASIS_3X (3<<22) #define FDI_DP_PORT_WIDTH_X1 (0<<19) #define FDI_DP_PORT_WIDTH_X2 (1<<19) #define FDI_DP_PORT_WIDTH_X3 (2<<19) #define FDI_DP_PORT_WIDTH_X4 (3<<19) #define FDI_TX_ENHANCE_FRAME_ENABLE (1<<18) /* IGDNG: hardwired to 1 */ #define FDI_TX_PLL_ENABLE (1<<14) /* both Tx and Rx */ #define FDI_SCRAMBLING_ENABLE (0<<7) #define FDI_SCRAMBLING_DISABLE (1<<7) /* FDI_RX, FDI_X is hard-wired to Transcoder_X */ #define FDI_RXA_CTL 0xf000c #define FDI_RXB_CTL 0xf100c #define FDI_RX_ENABLE (1<<31) #define FDI_RX_DISABLE (0<<31) /* train, dp width same as FDI_TX */ #define FDI_DP_PORT_WIDTH_X8 (7<<19) #define FDI_8BPC (0<<16) #define FDI_10BPC (1<<16) #define FDI_6BPC (2<<16) #define FDI_12BPC (3<<16) #define FDI_LINK_REVERSE_OVERWRITE (1<<15) #define FDI_DMI_LINK_REVERSE_MASK (1<<14) #define FDI_RX_PLL_ENABLE (1<<13) #define FDI_FS_ERR_CORRECT_ENABLE (1<<11) #define FDI_FE_ERR_CORRECT_ENABLE (1<<10) #define FDI_FS_ERR_REPORT_ENABLE (1<<9) #define FDI_FE_ERR_REPORT_ENABLE (1<<8) #define FDI_RX_ENHANCE_FRAME_ENABLE (1<<6) #define FDI_SEL_RAWCLK (0<<4) #define FDI_SEL_PCDCLK (1<<4) #define FDI_RXA_MISC 0xf0010 #define FDI_RXB_MISC 0xf1010 #define FDI_RXA_TUSIZE1 0xf0030 #define FDI_RXA_TUSIZE2 0xf0038 #define FDI_RXB_TUSIZE1 0xf1030 #define FDI_RXB_TUSIZE2 0xf1038 /* FDI_RX interrupt register format */ #define FDI_RX_INTER_LANE_ALIGN (1<<10) #define FDI_RX_SYMBOL_LOCK (1<<9) /* train 2 */ #define FDI_RX_BIT_LOCK (1<<8) /* train 1 */ #define FDI_RX_TRAIN_PATTERN_2_FAIL (1<<7) #define FDI_RX_FS_CODE_ERR (1<<6) #define FDI_RX_FE_CODE_ERR (1<<5) #define FDI_RX_SYMBOL_ERR_RATE_ABOVE (1<<4) #define FDI_RX_HDCP_LINK_FAIL (1<<3) #define FDI_RX_PIXEL_FIFO_OVERFLOW (1<<2) #define FDI_RX_CROSS_CLOCK_OVERFLOW (1<<1) #define FDI_RX_SYMBOL_QUEUE_OVERFLOW (1<<0) #define FDI_RXA_IIR 0xf0014 #define FDI_RXA_IMR 0xf0018 #define FDI_RXB_IIR 0xf1014 #define FDI_RXB_IMR 0xf1018 #define FDI_PLL_CTL_1 0xfe000 #define FDI_PLL_CTL_2 0xfe004 /* CRT */ #define PCH_ADPA 0xe1100 #define ADPA_TRANS_SELECT_MASK (1<<30) #define ADPA_TRANS_A_SELECT 0 #define ADPA_TRANS_B_SELECT (1<<30) #define ADPA_CRT_HOTPLUG_MASK 0x03ff0000 /* bit 25-16 */ #define ADPA_CRT_HOTPLUG_MONITOR_NONE (0<<24) #define ADPA_CRT_HOTPLUG_MONITOR_MASK (3<<24) #define ADPA_CRT_HOTPLUG_MONITOR_COLOR (3<<24) #define ADPA_CRT_HOTPLUG_MONITOR_MONO (2<<24) #define ADPA_CRT_HOTPLUG_ENABLE (1<<23) #define ADPA_CRT_HOTPLUG_PERIOD_64 (0<<22) #define ADPA_CRT_HOTPLUG_PERIOD_128 (1<<22) #define ADPA_CRT_HOTPLUG_WARMUP_5MS (0<<21) #define ADPA_CRT_HOTPLUG_WARMUP_10MS (1<<21) #define ADPA_CRT_HOTPLUG_SAMPLE_2S (0<<20) #define ADPA_CRT_HOTPLUG_SAMPLE_4S (1<<20) #define ADPA_CRT_HOTPLUG_VOLTAGE_40 (0<<18) #define ADPA_CRT_HOTPLUG_VOLTAGE_50 (1<<18) #define ADPA_CRT_HOTPLUG_VOLTAGE_60 (2<<18) #define ADPA_CRT_HOTPLUG_VOLTAGE_70 (3<<18) #define ADPA_CRT_HOTPLUG_VOLREF_325MV (0<<17) #define ADPA_CRT_HOTPLUG_VOLREF_475MV (1<<17) #define ADPA_CRT_HOTPLUG_FORCE_TRIGGER (1<<16) /* or SDVOB */ #define HDMIB 0xe1140 #define PORT_ENABLE (1 << 31) #define TRANSCODER_A (0) #define TRANSCODER_B (1 << 30) #define COLOR_FORMAT_8bpc (0) #define COLOR_FORMAT_12bpc (3 << 26) #define SDVOB_HOTPLUG_ENABLE (1 << 23) #define SDVO_ENCODING (0) #define TMDS_ENCODING (2 << 10) #define NULL_PACKET_VSYNC_ENABLE (1 << 9) #define SDVOB_BORDER_ENABLE (1 << 7) #define AUDIO_ENABLE (1 << 6) #define VSYNC_ACTIVE_HIGH (1 << 4) #define HSYNC_ACTIVE_HIGH (1 << 3) #define PORT_DETECTED (1 << 2) #define HDMIC 0xe1150 #define HDMID 0xe1160 #define PCH_LVDS 0xe1180 #define LVDS_DETECTED (1 << 1) #define BLC_PWM_CPU_CTL2 0x48250 #define PWM_ENABLE (1 << 31) #define PWM_PIPE_A (0 << 29) #define PWM_PIPE_B (1 << 29) #define BLC_PWM_CPU_CTL 0x48254 #define BLC_PWM_PCH_CTL1 0xc8250 #define PWM_PCH_ENABLE (1 << 31) #define PWM_POLARITY_ACTIVE_LOW (1 << 29) #define PWM_POLARITY_ACTIVE_HIGH (0 << 29) #define PWM_POLARITY_ACTIVE_LOW2 (1 << 28) #define PWM_POLARITY_ACTIVE_HIGH2 (0 << 28) #define BLC_PWM_PCH_CTL2 0xc8254 #define PCH_PP_STATUS 0xc7200 #define PCH_PP_CONTROL 0xc7204 #define EDP_FORCE_VDD (1 << 3) #define EDP_BLC_ENABLE (1 << 2) #define PANEL_POWER_RESET (1 << 1) #define PANEL_POWER_OFF (0 << 0) #define PANEL_POWER_ON (1 << 0) #define PCH_PP_ON_DELAYS 0xc7208 #define EDP_PANEL (1 << 30) #define PCH_PP_OFF_DELAYS 0xc720c #define PCH_PP_DIVISOR 0xc7210 #define PCH_DP_B 0xe4100 #define PCH_DPB_AUX_CH_CTL 0xe4110 #define PCH_DPB_AUX_CH_DATA1 0xe4114 #define PCH_DPB_AUX_CH_DATA2 0xe4118 #define PCH_DPB_AUX_CH_DATA3 0xe411c #define PCH_DPB_AUX_CH_DATA4 0xe4120 #define PCH_DPB_AUX_CH_DATA5 0xe4124 #define PCH_DP_C 0xe4200 #define PCH_DPC_AUX_CH_CTL 0xe4210 #define PCH_DPC_AUX_CH_DATA1 0xe4214 #define PCH_DPC_AUX_CH_DATA2 0xe4218 #define PCH_DPC_AUX_CH_DATA3 0xe421c #define PCH_DPC_AUX_CH_DATA4 0xe4220 #define PCH_DPC_AUX_CH_DATA5 0xe4224 #define PCH_DP_D 0xe4300 #define PCH_DPD_AUX_CH_CTL 0xe4310 #define PCH_DPD_AUX_CH_DATA1 0xe4314 #define PCH_DPD_AUX_CH_DATA2 0xe4318 #define PCH_DPD_AUX_CH_DATA3 0xe431c #define PCH_DPD_AUX_CH_DATA4 0xe4320 #define PCH_DPD_AUX_CH_DATA5 0xe4324 #endif /* _I915_REG_H_ */