// SPDX-License-Identifier: GPL-2.0 // Copyright (c) 2017-2018, The Linux foundation. All rights reserved. #if defined(CONFIG_SERIAL_QCOM_GENI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) # define SUPPORT_SYSRQ #endif #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* UART specific GENI registers */ #define SE_UART_LOOPBACK_CFG 0x22c #define SE_UART_TX_TRANS_CFG 0x25c #define SE_UART_TX_WORD_LEN 0x268 #define SE_UART_TX_STOP_BIT_LEN 0x26c #define SE_UART_TX_TRANS_LEN 0x270 #define SE_UART_RX_TRANS_CFG 0x280 #define SE_UART_RX_WORD_LEN 0x28c #define SE_UART_RX_STALE_CNT 0x294 #define SE_UART_TX_PARITY_CFG 0x2a4 #define SE_UART_RX_PARITY_CFG 0x2a8 #define SE_UART_MANUAL_RFR 0x2ac /* SE_UART_TRANS_CFG */ #define UART_TX_PAR_EN BIT(0) #define UART_CTS_MASK BIT(1) /* SE_UART_TX_WORD_LEN */ #define TX_WORD_LEN_MSK GENMASK(9, 0) /* SE_UART_TX_STOP_BIT_LEN */ #define TX_STOP_BIT_LEN_MSK GENMASK(23, 0) #define TX_STOP_BIT_LEN_1 0 #define TX_STOP_BIT_LEN_1_5 1 #define TX_STOP_BIT_LEN_2 2 /* SE_UART_TX_TRANS_LEN */ #define TX_TRANS_LEN_MSK GENMASK(23, 0) /* SE_UART_RX_TRANS_CFG */ #define UART_RX_INS_STATUS_BIT BIT(2) #define UART_RX_PAR_EN BIT(3) /* SE_UART_RX_WORD_LEN */ #define RX_WORD_LEN_MASK GENMASK(9, 0) /* SE_UART_RX_STALE_CNT */ #define RX_STALE_CNT GENMASK(23, 0) /* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */ #define PAR_CALC_EN BIT(0) #define PAR_MODE_MSK GENMASK(2, 1) #define PAR_MODE_SHFT 1 #define PAR_EVEN 0x00 #define PAR_ODD 0x01 #define PAR_SPACE 0x10 #define PAR_MARK 0x11 /* SE_UART_MANUAL_RFR register fields */ #define UART_MANUAL_RFR_EN BIT(31) #define UART_RFR_NOT_READY BIT(1) #define UART_RFR_READY BIT(0) /* UART M_CMD OP codes */ #define UART_START_TX 0x1 #define UART_START_BREAK 0x4 #define UART_STOP_BREAK 0x5 /* UART S_CMD OP codes */ #define UART_START_READ 0x1 #define UART_PARAM 0x1 #define UART_OVERSAMPLING 32 #define STALE_TIMEOUT 16 #define DEFAULT_BITS_PER_CHAR 10 #define GENI_UART_CONS_PORTS 1 #define GENI_UART_PORTS 3 #define DEF_FIFO_DEPTH_WORDS 16 #define DEF_TX_WM 2 #define DEF_FIFO_WIDTH_BITS 32 #define UART_CONSOLE_RX_WM 2 #define MAX_LOOPBACK_CFG 3 #ifdef CONFIG_CONSOLE_POLL #define CONSOLE_RX_BYTES_PW 1 #else #define CONSOLE_RX_BYTES_PW 4 #endif struct qcom_geni_serial_port { struct uart_port uport; struct geni_se se; char name[20]; u32 tx_fifo_depth; u32 tx_fifo_width; u32 rx_fifo_depth; u32 tx_wm; u32 rx_wm; u32 rx_rfr; enum geni_se_xfer_mode xfer_mode; bool setup; int (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop); unsigned int baud; unsigned int tx_bytes_pw; unsigned int rx_bytes_pw; u32 *rx_fifo; u32 loopback; bool brk; unsigned int tx_remaining; }; static const struct uart_ops qcom_geni_console_pops; static const struct uart_ops qcom_geni_uart_pops; static struct uart_driver qcom_geni_console_driver; static struct uart_driver qcom_geni_uart_driver; static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop); static int handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop); static unsigned int qcom_geni_serial_tx_empty(struct uart_port *port); static void qcom_geni_serial_stop_rx(struct uart_port *uport); static const unsigned long root_freq[] = {7372800, 14745600, 19200000, 29491200, 32000000, 48000000, 64000000, 80000000, 96000000, 100000000, 102400000, 112000000, 120000000, 128000000}; #define to_dev_port(ptr, member) \ container_of(ptr, struct qcom_geni_serial_port, member) static struct qcom_geni_serial_port qcom_geni_uart_ports[GENI_UART_PORTS] = { [0] = { .uport = { .iotype = UPIO_MEM, .ops = &qcom_geni_uart_pops, .flags = UPF_BOOT_AUTOCONF, .line = 0, }, }, [1] = { .uport = { .iotype = UPIO_MEM, .ops = &qcom_geni_uart_pops, .flags = UPF_BOOT_AUTOCONF, .line = 1, }, }, [2] = { .uport = { .iotype = UPIO_MEM, .ops = &qcom_geni_uart_pops, .flags = UPF_BOOT_AUTOCONF, .line = 2, }, }, }; static ssize_t loopback_show(struct device *dev, struct device_attribute *attr, char *buf) { struct qcom_geni_serial_port *port = dev_get_drvdata(dev); return snprintf(buf, sizeof(u32), "%d\n", port->loopback); } static ssize_t loopback_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t size) { struct qcom_geni_serial_port *port = dev_get_drvdata(dev); u32 loopback; if (kstrtoint(buf, 0, &loopback) || loopback > MAX_LOOPBACK_CFG) { dev_err(dev, "Invalid input\n"); return -EINVAL; } port->loopback = loopback; return size; } static DEVICE_ATTR_RW(loopback); static struct qcom_geni_serial_port qcom_geni_console_port = { .uport = { .iotype = UPIO_MEM, .ops = &qcom_geni_console_pops, .flags = UPF_BOOT_AUTOCONF, .line = 0, }, }; static int qcom_geni_serial_request_port(struct uart_port *uport) { struct platform_device *pdev = to_platform_device(uport->dev); struct qcom_geni_serial_port *port = to_dev_port(uport, uport); struct resource *res; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); uport->membase = devm_ioremap_resource(&pdev->dev, res); if (IS_ERR(uport->membase)) return PTR_ERR(uport->membase); port->se.base = uport->membase; return 0; } static void qcom_geni_serial_config_port(struct uart_port *uport, int cfg_flags) { if (cfg_flags & UART_CONFIG_TYPE) { uport->type = PORT_MSM; qcom_geni_serial_request_port(uport); } } static unsigned int qcom_geni_serial_get_mctrl(struct uart_port *uport) { unsigned int mctrl = TIOCM_DSR | TIOCM_CAR; u32 geni_ios; if (uart_console(uport) || !uart_cts_enabled(uport)) { mctrl |= TIOCM_CTS; } else { geni_ios = readl_relaxed(uport->membase + SE_GENI_IOS); if (!(geni_ios & IO2_DATA_IN)) mctrl |= TIOCM_CTS; } return mctrl; } static void qcom_geni_serial_set_mctrl(struct uart_port *uport, unsigned int mctrl) { u32 uart_manual_rfr = 0; if (uart_console(uport) || !uart_cts_enabled(uport)) return; if (!(mctrl & TIOCM_RTS)) uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY; writel_relaxed(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR); } static const char *qcom_geni_serial_get_type(struct uart_port *uport) { return "MSM"; } static struct qcom_geni_serial_port *get_port_from_line(int line, bool console) { struct qcom_geni_serial_port *port; int nr_ports = console ? GENI_UART_CONS_PORTS : GENI_UART_PORTS; if (line < 0 || line >= nr_ports) return ERR_PTR(-ENXIO); port = console ? &qcom_geni_console_port : &qcom_geni_uart_ports[line]; return port; } static bool qcom_geni_serial_poll_bit(struct uart_port *uport, int offset, int field, bool set) { u32 reg; struct qcom_geni_serial_port *port; unsigned int baud; unsigned int fifo_bits; unsigned long timeout_us = 20000; /* Ensure polling is not re-ordered before the prior writes/reads */ mb(); if (uport->private_data) { port = to_dev_port(uport, uport); baud = port->baud; if (!baud) baud = 115200; fifo_bits = port->tx_fifo_depth * port->tx_fifo_width; /* * Total polling iterations based on FIFO worth of bytes to be * sent at current baud. Add a little fluff to the wait. */ timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500; } /* * Use custom implementation instead of readl_poll_atomic since ktimer * is not ready at the time of early console. */ timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10; while (timeout_us) { reg = readl_relaxed(uport->membase + offset); if ((bool)(reg & field) == set) return true; udelay(10); timeout_us -= 10; } return false; } static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size) { u32 m_cmd; writel_relaxed(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN); m_cmd = UART_START_TX << M_OPCODE_SHFT; writel(m_cmd, uport->membase + SE_GENI_M_CMD0); } static void qcom_geni_serial_poll_tx_done(struct uart_port *uport) { int done; u32 irq_clear = M_CMD_DONE_EN; done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_DONE_EN, true); if (!done) { writel_relaxed(M_GENI_CMD_ABORT, uport->membase + SE_GENI_M_CMD_CTRL_REG); irq_clear |= M_CMD_ABORT_EN; qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); } writel_relaxed(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR); } static void qcom_geni_serial_abort_rx(struct uart_port *uport) { u32 irq_clear = S_CMD_DONE_EN | S_CMD_ABORT_EN; writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG); qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, S_GENI_CMD_ABORT, false); writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); writel_relaxed(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG); } #ifdef CONFIG_CONSOLE_POLL static int qcom_geni_serial_get_char(struct uart_port *uport) { u32 rx_fifo; u32 status; status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS); writel_relaxed(status, uport->membase + SE_GENI_M_IRQ_CLEAR); status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS); writel_relaxed(status, uport->membase + SE_GENI_S_IRQ_CLEAR); /* * Ensure the writes to clear interrupts is not re-ordered after * reading the data. */ mb(); status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS); if (!(status & RX_FIFO_WC_MSK)) return NO_POLL_CHAR; rx_fifo = readl(uport->membase + SE_GENI_RX_FIFOn); return rx_fifo & 0xff; } static void qcom_geni_serial_poll_put_char(struct uart_port *uport, unsigned char c) { struct qcom_geni_serial_port *port = to_dev_port(uport, uport); writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG); qcom_geni_serial_setup_tx(uport, 1); WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_TX_FIFO_WATERMARK_EN, true)); writel_relaxed(c, uport->membase + SE_GENI_TX_FIFOn); writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); qcom_geni_serial_poll_tx_done(uport); } #endif #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch) { writel_relaxed(ch, uport->membase + SE_GENI_TX_FIFOn); } static void __qcom_geni_serial_console_write(struct uart_port *uport, const char *s, unsigned int count) { int i; u32 bytes_to_send = count; for (i = 0; i < count; i++) { /* * uart_console_write() adds a carriage return for each newline. * Account for additional bytes to be written. */ if (s[i] == '\n') bytes_to_send++; } writel_relaxed(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); qcom_geni_serial_setup_tx(uport, bytes_to_send); for (i = 0; i < count; ) { size_t chars_to_write = 0; size_t avail = DEF_FIFO_DEPTH_WORDS - DEF_TX_WM; /* * If the WM bit never set, then the Tx state machine is not * in a valid state, so break, cancel/abort any existing * command. Unfortunately the current data being written is * lost. */ if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_TX_FIFO_WATERMARK_EN, true)) break; chars_to_write = min_t(size_t, count - i, avail / 2); uart_console_write(uport, s + i, chars_to_write, qcom_geni_serial_wr_char); writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); i += chars_to_write; } qcom_geni_serial_poll_tx_done(uport); } static void qcom_geni_serial_console_write(struct console *co, const char *s, unsigned int count) { struct uart_port *uport; struct qcom_geni_serial_port *port; bool locked = true; unsigned long flags; u32 geni_status; WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS); port = get_port_from_line(co->index, true); if (IS_ERR(port)) return; uport = &port->uport; if (oops_in_progress) locked = spin_trylock_irqsave(&uport->lock, flags); else spin_lock_irqsave(&uport->lock, flags); geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS); /* Cancel the current write to log the fault */ if (!locked) { geni_se_cancel_m_cmd(&port->se); if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_CANCEL_EN, true)) { geni_se_abort_m_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); writel_relaxed(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } else if ((geni_status & M_GENI_CMD_ACTIVE) && !port->tx_remaining) { /* * It seems we can't interrupt existing transfers if all data * has been sent, in which case we need to look for done first. */ qcom_geni_serial_poll_tx_done(uport); } __qcom_geni_serial_console_write(uport, s, count); if (port->tx_remaining) qcom_geni_serial_setup_tx(uport, port->tx_remaining); if (locked) spin_unlock_irqrestore(&uport->lock, flags); } static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop) { u32 i; unsigned char buf[sizeof(u32)]; struct tty_port *tport; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); tport = &uport->state->port; for (i = 0; i < bytes; ) { int c; int chunk = min_t(int, bytes - i, port->rx_bytes_pw); ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, buf, 1); i += chunk; if (drop) continue; for (c = 0; c < chunk; c++) { int sysrq; uport->icount.rx++; if (port->brk && buf[c] == 0) { port->brk = false; if (uart_handle_break(uport)) continue; } sysrq = uart_prepare_sysrq_char(uport, buf[c]); if (!sysrq) tty_insert_flip_char(tport, buf[c], TTY_NORMAL); } } if (!drop) tty_flip_buffer_push(tport); return 0; } #else static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop) { return -EPERM; } #endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */ static int handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop) { unsigned char *buf; struct tty_port *tport; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); u32 num_bytes_pw = port->tx_fifo_width / BITS_PER_BYTE; u32 words = ALIGN(bytes, num_bytes_pw) / num_bytes_pw; int ret; tport = &uport->state->port; ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, port->rx_fifo, words); if (drop) return 0; buf = (unsigned char *)port->rx_fifo; ret = tty_insert_flip_string(tport, buf, bytes); if (ret != bytes) { dev_err(uport->dev, "%s:Unable to push data ret %d_bytes %d\n", __func__, ret, bytes); WARN_ON_ONCE(1); } uport->icount.rx += ret; tty_flip_buffer_push(tport); return ret; } static void qcom_geni_serial_start_tx(struct uart_port *uport) { u32 irq_en; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); u32 status; if (port->xfer_mode == GENI_SE_FIFO) { /* * readl ensures reading & writing of IRQ_EN register * is not re-ordered before checking the status of the * Serial Engine. */ status = readl(uport->membase + SE_GENI_STATUS); if (status & M_GENI_CMD_ACTIVE) return; if (!qcom_geni_serial_tx_empty(uport)) return; irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN; writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG); writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); } } static void qcom_geni_serial_stop_tx(struct uart_port *uport) { u32 irq_en; u32 status; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); irq_en &= ~M_CMD_DONE_EN; if (port->xfer_mode == GENI_SE_FIFO) { irq_en &= ~M_TX_FIFO_WATERMARK_EN; writel_relaxed(0, uport->membase + SE_GENI_TX_WATERMARK_REG); } writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); status = readl_relaxed(uport->membase + SE_GENI_STATUS); /* Possible stop tx is called multiple times. */ if (!(status & M_GENI_CMD_ACTIVE)) return; /* * Ensure cancel command write is not re-ordered before checking * the status of the Primary Sequencer. */ mb(); geni_se_cancel_m_cmd(&port->se); if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_CANCEL_EN, true)) { geni_se_abort_m_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); writel_relaxed(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } static void qcom_geni_serial_start_rx(struct uart_port *uport) { u32 irq_en; u32 status; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); status = readl_relaxed(uport->membase + SE_GENI_STATUS); if (status & S_GENI_CMD_ACTIVE) qcom_geni_serial_stop_rx(uport); /* * Ensure setup command write is not re-ordered before checking * the status of the Secondary Sequencer. */ mb(); geni_se_setup_s_cmd(&port->se, UART_START_READ, 0); if (port->xfer_mode == GENI_SE_FIFO) { irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN); irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN; writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN); irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); } } static void qcom_geni_serial_stop_rx(struct uart_port *uport) { u32 irq_en; u32 status; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); u32 irq_clear = S_CMD_DONE_EN; if (port->xfer_mode == GENI_SE_FIFO) { irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN); irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN); writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN); irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN); writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); } status = readl_relaxed(uport->membase + SE_GENI_STATUS); /* Possible stop rx is called multiple times. */ if (!(status & S_GENI_CMD_ACTIVE)) return; /* * Ensure cancel command write is not re-ordered before checking * the status of the Secondary Sequencer. */ mb(); geni_se_cancel_s_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, S_GENI_CMD_CANCEL, false); status = readl_relaxed(uport->membase + SE_GENI_STATUS); writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); if (status & S_GENI_CMD_ACTIVE) qcom_geni_serial_abort_rx(uport); } static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop) { u32 status; u32 word_cnt; u32 last_word_byte_cnt; u32 last_word_partial; u32 total_bytes; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS); word_cnt = status & RX_FIFO_WC_MSK; last_word_partial = status & RX_LAST; last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >> RX_LAST_BYTE_VALID_SHFT; if (!word_cnt) return; total_bytes = port->rx_bytes_pw * (word_cnt - 1); if (last_word_partial && last_word_byte_cnt) total_bytes += last_word_byte_cnt; else total_bytes += port->rx_bytes_pw; port->handle_rx(uport, total_bytes, drop); } static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done, bool active) { struct qcom_geni_serial_port *port = to_dev_port(uport, uport); struct circ_buf *xmit = &uport->state->xmit; size_t avail; size_t remaining; size_t pending; int i; u32 status; unsigned int chunk; int tail; status = readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS); /* Complete the current tx command before taking newly added data */ if (active) pending = port->tx_remaining; else pending = uart_circ_chars_pending(xmit); /* All data has been transmitted and acknowledged as received */ if (!pending && !status && done) { qcom_geni_serial_stop_tx(uport); goto out_write_wakeup; } avail = port->tx_fifo_depth - (status & TX_FIFO_WC); avail *= port->tx_bytes_pw; tail = xmit->tail; chunk = min3(avail, pending, (size_t)(UART_XMIT_SIZE - tail)); if (!chunk) goto out_write_wakeup; if (!port->tx_remaining) { qcom_geni_serial_setup_tx(uport, pending); port->tx_remaining = pending; } remaining = chunk; for (i = 0; i < chunk; ) { unsigned int tx_bytes; u8 buf[sizeof(u32)]; int c; memset(buf, 0, ARRAY_SIZE(buf)); tx_bytes = min_t(size_t, remaining, port->tx_bytes_pw); for (c = 0; c < tx_bytes ; c++) buf[c] = xmit->buf[tail + c]; iowrite32_rep(uport->membase + SE_GENI_TX_FIFOn, buf, 1); i += tx_bytes; tail += tx_bytes; uport->icount.tx += tx_bytes; remaining -= tx_bytes; port->tx_remaining -= tx_bytes; } xmit->tail = tail & (UART_XMIT_SIZE - 1); out_write_wakeup: if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) uart_write_wakeup(uport); } static irqreturn_t qcom_geni_serial_isr(int isr, void *dev) { unsigned int m_irq_status; unsigned int s_irq_status; unsigned int geni_status; struct uart_port *uport = dev; unsigned long flags; unsigned int m_irq_en; bool drop_rx = false; struct tty_port *tport = &uport->state->port; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); if (uport->suspended) return IRQ_NONE; spin_lock_irqsave(&uport->lock, flags); m_irq_status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS); s_irq_status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS); geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS); m_irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); writel_relaxed(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR); writel_relaxed(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN)) goto out_unlock; if (s_irq_status & S_RX_FIFO_WR_ERR_EN) { uport->icount.overrun++; tty_insert_flip_char(tport, 0, TTY_OVERRUN); } if (m_irq_status & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN) && m_irq_en & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN)) qcom_geni_serial_handle_tx(uport, m_irq_status & M_CMD_DONE_EN, geni_status & M_GENI_CMD_ACTIVE); if (s_irq_status & S_GP_IRQ_0_EN || s_irq_status & S_GP_IRQ_1_EN) { if (s_irq_status & S_GP_IRQ_0_EN) uport->icount.parity++; drop_rx = true; } else if (s_irq_status & S_GP_IRQ_2_EN || s_irq_status & S_GP_IRQ_3_EN) { uport->icount.brk++; port->brk = true; } if (s_irq_status & S_RX_FIFO_WATERMARK_EN || s_irq_status & S_RX_FIFO_LAST_EN) qcom_geni_serial_handle_rx(uport, drop_rx); out_unlock: uart_unlock_and_check_sysrq(uport, flags); return IRQ_HANDLED; } static void get_tx_fifo_size(struct qcom_geni_serial_port *port) { struct uart_port *uport; uport = &port->uport; port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se); port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se); port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se); uport->fifosize = (port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE; } static void set_rfr_wm(struct qcom_geni_serial_port *port) { /* * Set RFR (Flow off) to FIFO_DEPTH - 2. * RX WM level at 10% RX_FIFO_DEPTH. * TX WM level at 10% TX_FIFO_DEPTH. */ port->rx_rfr = port->rx_fifo_depth - 2; port->rx_wm = UART_CONSOLE_RX_WM; port->tx_wm = DEF_TX_WM; } static void qcom_geni_serial_shutdown(struct uart_port *uport) { unsigned long flags; /* Stop the console before stopping the current tx */ if (uart_console(uport)) console_stop(uport->cons); free_irq(uport->irq, uport); spin_lock_irqsave(&uport->lock, flags); qcom_geni_serial_stop_tx(uport); qcom_geni_serial_stop_rx(uport); spin_unlock_irqrestore(&uport->lock, flags); } static int qcom_geni_serial_port_setup(struct uart_port *uport) { struct qcom_geni_serial_port *port = to_dev_port(uport, uport); unsigned int rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT; u32 proto; if (uart_console(uport)) { port->tx_bytes_pw = 1; port->rx_bytes_pw = CONSOLE_RX_BYTES_PW; } else { port->tx_bytes_pw = 4; port->rx_bytes_pw = 4; } proto = geni_se_read_proto(&port->se); if (proto != GENI_SE_UART) { dev_err(uport->dev, "Invalid FW loaded, proto: %d\n", proto); return -ENXIO; } qcom_geni_serial_stop_rx(uport); get_tx_fifo_size(port); set_rfr_wm(port); writel_relaxed(rxstale, uport->membase + SE_UART_RX_STALE_CNT); /* * Make an unconditional cancel on the main sequencer to reset * it else we could end up in data loss scenarios. */ port->xfer_mode = GENI_SE_FIFO; if (uart_console(uport)) qcom_geni_serial_poll_tx_done(uport); geni_se_config_packing(&port->se, BITS_PER_BYTE, port->tx_bytes_pw, false, true, false); geni_se_config_packing(&port->se, BITS_PER_BYTE, port->rx_bytes_pw, false, false, true); geni_se_init(&port->se, port->rx_wm, port->rx_rfr); geni_se_select_mode(&port->se, port->xfer_mode); if (!uart_console(uport)) { port->rx_fifo = devm_kcalloc(uport->dev, port->rx_fifo_depth, sizeof(u32), GFP_KERNEL); if (!port->rx_fifo) return -ENOMEM; } port->setup = true; return 0; } static int qcom_geni_serial_startup(struct uart_port *uport) { int ret; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); scnprintf(port->name, sizeof(port->name), "qcom_serial_%s%d", (uart_console(uport) ? "console" : "uart"), uport->line); if (!port->setup) { ret = qcom_geni_serial_port_setup(uport); if (ret) return ret; } ret = request_irq(uport->irq, qcom_geni_serial_isr, IRQF_TRIGGER_HIGH, port->name, uport); if (ret) dev_err(uport->dev, "Failed to get IRQ ret %d\n", ret); return ret; } static unsigned long get_clk_cfg(unsigned long clk_freq) { int i; for (i = 0; i < ARRAY_SIZE(root_freq); i++) { if (!(root_freq[i] % clk_freq)) return root_freq[i]; } return 0; } static unsigned long get_clk_div_rate(unsigned int baud, unsigned int *clk_div) { unsigned long ser_clk; unsigned long desired_clk; desired_clk = baud * UART_OVERSAMPLING; ser_clk = get_clk_cfg(desired_clk); if (!ser_clk) { pr_err("%s: Can't find matching DFS entry for baud %d\n", __func__, baud); return ser_clk; } *clk_div = ser_clk / desired_clk; return ser_clk; } static void qcom_geni_serial_set_termios(struct uart_port *uport, struct ktermios *termios, struct ktermios *old) { unsigned int baud; unsigned int bits_per_char; unsigned int tx_trans_cfg; unsigned int tx_parity_cfg; unsigned int rx_trans_cfg; unsigned int rx_parity_cfg; unsigned int stop_bit_len; unsigned int clk_div; unsigned long ser_clk_cfg; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); unsigned long clk_rate; qcom_geni_serial_stop_rx(uport); /* baud rate */ baud = uart_get_baud_rate(uport, termios, old, 300, 4000000); port->baud = baud; clk_rate = get_clk_div_rate(baud, &clk_div); if (!clk_rate) goto out_restart_rx; uport->uartclk = clk_rate; clk_set_rate(port->se.clk, clk_rate); ser_clk_cfg = SER_CLK_EN; ser_clk_cfg |= clk_div << CLK_DIV_SHFT; /* parity */ tx_trans_cfg = readl_relaxed(uport->membase + SE_UART_TX_TRANS_CFG); tx_parity_cfg = readl_relaxed(uport->membase + SE_UART_TX_PARITY_CFG); rx_trans_cfg = readl_relaxed(uport->membase + SE_UART_RX_TRANS_CFG); rx_parity_cfg = readl_relaxed(uport->membase + SE_UART_RX_PARITY_CFG); if (termios->c_cflag & PARENB) { tx_trans_cfg |= UART_TX_PAR_EN; rx_trans_cfg |= UART_RX_PAR_EN; tx_parity_cfg |= PAR_CALC_EN; rx_parity_cfg |= PAR_CALC_EN; if (termios->c_cflag & PARODD) { tx_parity_cfg |= PAR_ODD; rx_parity_cfg |= PAR_ODD; } else if (termios->c_cflag & CMSPAR) { tx_parity_cfg |= PAR_SPACE; rx_parity_cfg |= PAR_SPACE; } else { tx_parity_cfg |= PAR_EVEN; rx_parity_cfg |= PAR_EVEN; } } else { tx_trans_cfg &= ~UART_TX_PAR_EN; rx_trans_cfg &= ~UART_RX_PAR_EN; tx_parity_cfg &= ~PAR_CALC_EN; rx_parity_cfg &= ~PAR_CALC_EN; } /* bits per char */ switch (termios->c_cflag & CSIZE) { case CS5: bits_per_char = 5; break; case CS6: bits_per_char = 6; break; case CS7: bits_per_char = 7; break; case CS8: default: bits_per_char = 8; break; } /* stop bits */ if (termios->c_cflag & CSTOPB) stop_bit_len = TX_STOP_BIT_LEN_2; else stop_bit_len = TX_STOP_BIT_LEN_1; /* flow control, clear the CTS_MASK bit if using flow control. */ if (termios->c_cflag & CRTSCTS) tx_trans_cfg &= ~UART_CTS_MASK; else tx_trans_cfg |= UART_CTS_MASK; if (baud) uart_update_timeout(uport, termios->c_cflag, baud); if (!uart_console(uport)) writel_relaxed(port->loopback, uport->membase + SE_UART_LOOPBACK_CFG); writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG); writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG); out_restart_rx: qcom_geni_serial_start_rx(uport); } static unsigned int qcom_geni_serial_tx_empty(struct uart_port *uport) { return !readl(uport->membase + SE_GENI_TX_FIFO_STATUS); } #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE static int __init qcom_geni_console_setup(struct console *co, char *options) { struct uart_port *uport; struct qcom_geni_serial_port *port; int baud; int bits = 8; int parity = 'n'; int flow = 'n'; int ret; if (co->index >= GENI_UART_CONS_PORTS || co->index < 0) return -ENXIO; port = get_port_from_line(co->index, true); if (IS_ERR(port)) { pr_err("Invalid line %d\n", co->index); return PTR_ERR(port); } uport = &port->uport; if (unlikely(!uport->membase)) return -ENXIO; if (!port->setup) { ret = qcom_geni_serial_port_setup(uport); if (ret) return ret; } if (options) uart_parse_options(options, &baud, &parity, &bits, &flow); return uart_set_options(uport, co, baud, parity, bits, flow); } static void qcom_geni_serial_earlycon_write(struct console *con, const char *s, unsigned int n) { struct earlycon_device *dev = con->data; __qcom_geni_serial_console_write(&dev->port, s, n); } static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev, const char *opt) { struct uart_port *uport = &dev->port; u32 tx_trans_cfg; u32 tx_parity_cfg = 0; /* Disable Tx Parity */ u32 rx_trans_cfg = 0; u32 rx_parity_cfg = 0; /* Disable Rx Parity */ u32 stop_bit_len = 0; /* Default stop bit length - 1 bit */ u32 bits_per_char; struct geni_se se; if (!uport->membase) return -EINVAL; memset(&se, 0, sizeof(se)); se.base = uport->membase; if (geni_se_read_proto(&se) != GENI_SE_UART) return -ENXIO; /* * Ignore Flow control. * n = 8. */ tx_trans_cfg = UART_CTS_MASK; bits_per_char = BITS_PER_BYTE; /* * Make an unconditional cancel on the main sequencer to reset * it else we could end up in data loss scenarios. */ qcom_geni_serial_poll_tx_done(uport); qcom_geni_serial_abort_rx(uport); geni_se_config_packing(&se, BITS_PER_BYTE, 1, false, true, false); geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2); geni_se_select_mode(&se, GENI_SE_FIFO); writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); dev->con->write = qcom_geni_serial_earlycon_write; dev->con->setup = NULL; return 0; } OF_EARLYCON_DECLARE(qcom_geni, "qcom,geni-debug-uart", qcom_geni_serial_earlycon_setup); static int __init console_register(struct uart_driver *drv) { return uart_register_driver(drv); } static void console_unregister(struct uart_driver *drv) { uart_unregister_driver(drv); } static struct console cons_ops = { .name = "ttyMSM", .write = qcom_geni_serial_console_write, .device = uart_console_device, .setup = qcom_geni_console_setup, .flags = CON_PRINTBUFFER, .index = -1, .data = &qcom_geni_console_driver, }; static struct uart_driver qcom_geni_console_driver = { .owner = THIS_MODULE, .driver_name = "qcom_geni_console", .dev_name = "ttyMSM", .nr = GENI_UART_CONS_PORTS, .cons = &cons_ops, }; #else static int console_register(struct uart_driver *drv) { return 0; } static void console_unregister(struct uart_driver *drv) { } #endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */ static struct uart_driver qcom_geni_uart_driver = { .owner = THIS_MODULE, .driver_name = "qcom_geni_uart", .dev_name = "ttyHS", .nr = GENI_UART_PORTS, }; static void qcom_geni_serial_pm(struct uart_port *uport, unsigned int new_state, unsigned int old_state) { struct qcom_geni_serial_port *port = to_dev_port(uport, uport); /* If we've never been called, treat it as off */ if (old_state == UART_PM_STATE_UNDEFINED) old_state = UART_PM_STATE_OFF; if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF) geni_se_resources_on(&port->se); else if (new_state == UART_PM_STATE_OFF && old_state == UART_PM_STATE_ON) geni_se_resources_off(&port->se); } static const struct uart_ops qcom_geni_console_pops = { .tx_empty = qcom_geni_serial_tx_empty, .stop_tx = qcom_geni_serial_stop_tx, .start_tx = qcom_geni_serial_start_tx, .stop_rx = qcom_geni_serial_stop_rx, .set_termios = qcom_geni_serial_set_termios, .startup = qcom_geni_serial_startup, .request_port = qcom_geni_serial_request_port, .config_port = qcom_geni_serial_config_port, .shutdown = qcom_geni_serial_shutdown, .type = qcom_geni_serial_get_type, .set_mctrl = qcom_geni_serial_set_mctrl, .get_mctrl = qcom_geni_serial_get_mctrl, #ifdef CONFIG_CONSOLE_POLL .poll_get_char = qcom_geni_serial_get_char, .poll_put_char = qcom_geni_serial_poll_put_char, #endif .pm = qcom_geni_serial_pm, }; static const struct uart_ops qcom_geni_uart_pops = { .tx_empty = qcom_geni_serial_tx_empty, .stop_tx = qcom_geni_serial_stop_tx, .start_tx = qcom_geni_serial_start_tx, .stop_rx = qcom_geni_serial_stop_rx, .set_termios = qcom_geni_serial_set_termios, .startup = qcom_geni_serial_startup, .request_port = qcom_geni_serial_request_port, .config_port = qcom_geni_serial_config_port, .shutdown = qcom_geni_serial_shutdown, .type = qcom_geni_serial_get_type, .set_mctrl = qcom_geni_serial_set_mctrl, .get_mctrl = qcom_geni_serial_get_mctrl, .pm = qcom_geni_serial_pm, }; static int qcom_geni_serial_probe(struct platform_device *pdev) { int ret = 0; int line = -1; struct qcom_geni_serial_port *port; struct uart_port *uport; struct resource *res; int irq; bool console = false; struct uart_driver *drv; if (of_device_is_compatible(pdev->dev.of_node, "qcom,geni-debug-uart")) console = true; if (console) { drv = &qcom_geni_console_driver; line = of_alias_get_id(pdev->dev.of_node, "serial"); } else { drv = &qcom_geni_uart_driver; line = of_alias_get_id(pdev->dev.of_node, "hsuart"); } port = get_port_from_line(line, console); if (IS_ERR(port)) { dev_err(&pdev->dev, "Invalid line %d\n", line); return PTR_ERR(port); } uport = &port->uport; /* Don't allow 2 drivers to access the same port */ if (uport->private_data) return -ENODEV; uport->dev = &pdev->dev; port->se.dev = &pdev->dev; port->se.wrapper = dev_get_drvdata(pdev->dev.parent); port->se.clk = devm_clk_get(&pdev->dev, "se"); if (IS_ERR(port->se.clk)) { ret = PTR_ERR(port->se.clk); dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret); return ret; } res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!res) return -EINVAL; uport->mapbase = res->start; port->tx_fifo_depth = DEF_FIFO_DEPTH_WORDS; port->rx_fifo_depth = DEF_FIFO_DEPTH_WORDS; port->tx_fifo_width = DEF_FIFO_WIDTH_BITS; irq = platform_get_irq(pdev, 0); if (irq < 0) { dev_err(&pdev->dev, "Failed to get IRQ %d\n", irq); return irq; } uport->irq = irq; uport->private_data = drv; platform_set_drvdata(pdev, port); port->handle_rx = console ? handle_rx_console : handle_rx_uart; if (!console) device_create_file(uport->dev, &dev_attr_loopback); return uart_add_one_port(drv, uport); } static int qcom_geni_serial_remove(struct platform_device *pdev) { struct qcom_geni_serial_port *port = platform_get_drvdata(pdev); struct uart_driver *drv = port->uport.private_data; uart_remove_one_port(drv, &port->uport); return 0; } static int __maybe_unused qcom_geni_serial_sys_suspend(struct device *dev) { struct qcom_geni_serial_port *port = dev_get_drvdata(dev); struct uart_port *uport = &port->uport; return uart_suspend_port(uport->private_data, uport); } static int __maybe_unused qcom_geni_serial_sys_resume(struct device *dev) { struct qcom_geni_serial_port *port = dev_get_drvdata(dev); struct uart_port *uport = &port->uport; return uart_resume_port(uport->private_data, uport); } static const struct dev_pm_ops qcom_geni_serial_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(qcom_geni_serial_sys_suspend, qcom_geni_serial_sys_resume) }; static const struct of_device_id qcom_geni_serial_match_table[] = { { .compatible = "qcom,geni-debug-uart", }, { .compatible = "qcom,geni-uart", }, {} }; MODULE_DEVICE_TABLE(of, qcom_geni_serial_match_table); static struct platform_driver qcom_geni_serial_platform_driver = { .remove = qcom_geni_serial_remove, .probe = qcom_geni_serial_probe, .driver = { .name = "qcom_geni_serial", .of_match_table = qcom_geni_serial_match_table, .pm = &qcom_geni_serial_pm_ops, }, }; static int __init qcom_geni_serial_init(void) { int ret; ret = console_register(&qcom_geni_console_driver); if (ret) return ret; ret = uart_register_driver(&qcom_geni_uart_driver); if (ret) { console_unregister(&qcom_geni_console_driver); return ret; } ret = platform_driver_register(&qcom_geni_serial_platform_driver); if (ret) { console_unregister(&qcom_geni_console_driver); uart_unregister_driver(&qcom_geni_uart_driver); } return ret; } module_init(qcom_geni_serial_init); static void __exit qcom_geni_serial_exit(void) { platform_driver_unregister(&qcom_geni_serial_platform_driver); console_unregister(&qcom_geni_console_driver); uart_unregister_driver(&qcom_geni_uart_driver); } module_exit(qcom_geni_serial_exit); MODULE_DESCRIPTION("Serial driver for GENI based QUP cores"); MODULE_LICENSE("GPL v2");